The FCC has adopted a safety standard for human exposure to RF energy. Proper
operation of this radio under normal conditions results in user exposure to RF energy
below the Occupational Safety and Health Act and Federal Communication
Commission limits.
Mandatory Safety Instructions to Installers and Users:
This radio is NOT approved for use by the general population in an uncontrolled
environment. This radio is restricted to occupational use and work related operations
only. Radio operators must have the knowledge to control their exposure conditions
and the exposure conditions of bystanders and/or passengers to satisfy the lower
exposure limit allowed for General Population.
To comply with FCC RF exposure limits, DO NOT operate the transmitter of this mobile
radio when a person outside the vehicle is within 38 inches (94 centimeters) of the
antenna.
The antenna supplied by the manufacturer or radio dealer must be mounted at a
location such that during radio transmission, no person or persons can come closer
than the above indicated minimum safe distance to the antenna, i.e. 38 inches. To
comply with current FCC RF exposure limits, the antenna must be installed at or
exceeding the minimum safe distance stated above, and in accordance with the
requirements of the antenna manufacturer or supplier.
Vehicle Installation Instructions:
The antenna used for this transmitter must be mounted on the center of the roof ONLY
and must be installed in vehicle having the following characteristics in order to prevent
bystanders and passengers from being exposed to levels exceeding the limits for
General Population/Uncontrolled Exposure environment:
1. All passengers must be sitting under a solid metal roof.
2. Rooftop width must be at least 76 inches (183 centimeters) OR the edges of the
physical boundary of the vehicle must be at least 76 inches apart.
DO NOT operate the radio without the proper antenna installed. Do not substitute any
antenna for the one supplied or recommended by the manufacturer or radio dealer. The
antenna gain must not exceed 0 dBd. By not following the antenna recommendations
you may be exposing person(s) to excess radio frequency radiation. You may contact
your radio dealer or the manufacturer for further instructions.
DO NOT transmit more than 50% of total radio use time (50% duty cycle). Transmitting
for more than 50% of the time can cause FCC RF exposure compliance requirements
to be exceeded. This radio is transmitting whenever the TX icon is displayed on the
radio LCD. Pressing the PTT switch on the side of the microphone normally causes the
radio to transmit.
The preceding information is provided to make you aware of RF exposure and
how to ensure that this radio is operated within FCC RF exposure limits.
You, as the qualified end-user of this radio device must control the exposure conditions
of bystanders to ensure the minimum separation distance, stated above for satisfying
FCC RF exposure compliance, is maintained between the antenna and nearby
persons. Transmit only when all person(s) are at least the minimum distance from the
properly installed, externally mounted antenna.
This symbol marks a “caution”. Cautions are special notices
which you should read and follow carefully to avoid possible
damage to your equipment and to avoid potential danger to
yourself or other people.
! This symbol marks an “important point”. Important points are
specific instructions which should be followed closely for proper
operation.
This symbol marks a “note”. Notes are hints or tips which offer
additional information to help you.
Disclaimer
Midland Radio Corporation is committed to continuous quality
improvements, for this reason specifications may change without
prior notice.
Every effort has been made to ensure that the information in this
document is complete, accurate, and up-to-date. Midland
assumes no responsibility for the results of errors beyond its
control. The manufacturer of this equipment also cannot
guarantee that changes in the equipment made by unauthorized
people will not affect the transceiver’s performance or functions.
Safety
Your Titan™ mobile transceiver has been carefully designed to
give you years of safe, reliable performance. As with all electrical
equipment, however, there are a few basic precautions you
should take to avoid injury to yourself or damage to the radio:
Read the instructions in this book carefully. Be sure to save it for
future reference.
Read and follow all warning and instruction labels on the radio
itself.
Be sure the PTT button is not pressed when you do not need to
Do not operate the radio near unshielded electrical blasting caps
or in an explosive atmosphere.
Do not operate the transmitter of any radio unless all RF
connectors are secure.
All equipment must be properly grounded for safe operation.
Do not allow children to operate or play with the radio equipment.
Never attempt to disassemble or service the radio yourself. All
equipment should be serviced by a qualified technician. Contact you
local dealer or communications coordinator for assistance.
It is mandatory that radio installations in vehicles fueled by
liquefied petroleum gas conform to the NFPA 58 standard. National
Fire Protection Association Standard, NFPA 58, applies to radio
installations in vehicles fueled by liquefied petroleum (LP) gas with the
LP gas container in the trunk or other sealed-off space within the interior
of the vehicle. This standard requires that:
1. Any space containing radio equipment shall be isolated by a seal
from the space in which the LP gas container and its fittings are
located.
2. Remote (outside) filling connections shall be vented to the
outside.
Do not allow the antenna to touch or come in very close proximity
with the eyes, face, or any exposed body parts while the radio is
transmitting.
The above warning list is not intended to include all hazards that may
Congratulations! By choosing the Midland Titan™ mobile
transceiver, you have selected a professional grade radio. Its
rugged design will provide years of reliable service and
exceptional performance.
Radio Models
The models in the Titan mobile radio line allow selection by
frequency band, transmit power, control head, and mounting
configuration.
transmit power for mid power radios. 100 Watts (UHF)/110 Watts (VHFHigh Band)/110 Watts (VHF-Low Band) transmit power for high power
radios
5 12.5 KHz and 25 KHz channel spacing programmable per channel.
5 Auxiliary button for activation of optional accessories.
5 Software adjusted noise squelch level. The squelch level may be easily
adjusted using the menu functions.
5Flexible scan programming allows for two priority channels to be
assigned. Priority scan, priority transmit and priority lookback are
standard. Nuisance delete and scan escape functions are available.
5 Extensive and simple scan list editing functions.
5 User selectable scan modes (busy scan, priority scan and public safety
scan).
5 47 CTCSS tones and 104 DCS codes are programmable per channel.
5 A busy channel lockout feature is programmable. An override function is
available to allow transmission during repeater hangtime.
5A transmit time-out timer may be programmed to limit continuous
transmission time.
5The AUX button may be configured to provide repeater talk-around
without using an additional channel.
5 2-tone decode built-in. Individual and group calls can be decoded.
5 A DTMF ANI sequence may be sent on PTT press. A thirty second PTT
release timer is standard.
5 Audio compandering programmable per channel.
5 Radio alignment is performed using programming software.
70-2202 Standard (three character) control head
70-2203 Deluxe (twelve character) control head
70-2278 Trunk mount conversion kit
70-2290 Under dash mounting bracket
70-2291 Trunk mount tray
70-2358 Remote speaker
Cables
70-0038 6 meter DC power cable (mid power radios)
70-0039 2 meter DC power cable (mid power radios)
70-0042 2 meter DC power cable (high power radios)
70-0046 6 meter DC power cable (high power radios)
70-0076 6 meter control cable
70-0076QC 7 meter quick connect control cable
Base Equipment
70-2020D Tone termination panel (factory install only)
70-2286 11 Amp power supply w/shroud (mid-power radios)
70-2305BT Desktop microphone
for VHF-low and UHF band mobiles
(factory install only)
70-2945-2A Internal UHF mobile repeater package
for VHF-low and VHF-high band mobiles
(factory install only)