Midea MIEA1091 w

File SA12879

Project 4786113407

November 20, 2013

REPORT

On

HOUSEHOLD FREEZERS

Hefei Hualing Co Ltd

Hefei, Anhui, China

Copyright2013 UL LLC

UL LLC authorizes the above named company to reproduce this Report only
for purposes as described in the Conclusion, provided it is reproduced
in its entirety.

File SA12879 Vol. 1 Sec. 7 Page 1 Issued: 2013-11-20

and Report Revised: 2021-11-01

DESCRIPTION

PRODUCT COVERED:

USL, CNL Free standing type household freezer, Models HS-109FN(SNZ), HS-

109FN(S2NZ), MDUF3**(* can be WH/BK/SS as different color of the
same model), DSD-109MU, CUF-301SS, ARU030S1ARWW, ARU030S1ARSS,
UF300WE, UF-304W, UF-304SS, CUF-301, MRF-161, CF2137, WHS-109FW1,
WHS-109FB1, WHS-109FSS1, CUF30M1W, KTUF88, CUF-301BK, MRU03M2ABB,
HS-52FN(SNZ), HS-52FN(S2NZ), CUF-110, CMF151L-1, CRF150SS-1,
MUFM011AEW, MUFM011AEB, MUFM011AES, MUFM011AET, AUFM011AEW,
AUFM011AEB, AUFM011AES, AUFM011AET, FKAUFM011AEW, FKAUFM011AEB,
FKAUFM011AES, FKAUFM011AET, BAUFM011AEW, BAUFM011AEB, BAUFM011AES,
BAUFM011AET, MNAUFM011AEW, MNAUFM011AEB, MNAUFM011AES,
MNAUFM011AET, UF-114W, UF-114SS, CMF151L, CRF150SS, WHS-52FW1,
WHS-52FB1, WHS-52FSS1, CUF-110, AUFM011AEW, AUFM011AEOT, HS­129CN(NZ), NS-CZ35WH7, NS-CZ35WH7-C, WHS-129C1WSB, WHS-129C1,
KTCF99, ACFM035ADW, ACFM035BDW, ACFM035ADOT, HME030048N, CR350,
3W1CF35, HS-129CN(SNZ), URBD99DE, WHS-129C1W, HS-255FN(NZ), NS­UZ7WH0, MDUF7WH, MDUF7SS, HS-255FN(2NZ), MDUFC7SS, MRU01M3AWW,
MRU01M3ABB, MRU01M3ASL, MRU07M2AWW, FC-1301K, FC-1300W, FC-1110K,
FC-1110W, ARU03M2AWW, CU7DSWBR1RCM, CUF-301BK, CUF-301SS,
ARU030S1ARWW, ARU030S1ARSS, WHS-109FW1, MRU03M2ABB, CUF30M1W,
043-2352-8, H11MFW, H11MFB, H11MFS.

GENERAL:

The models covered in this Report are self-contained freezers. They
employ no defrost system. These units are intended for indoor freestanding
use. An attached length of power supply and terminating in a grounding type
attachment plug is provided for connection to the electrical supply source.

The models employ Refrigerant R-600a (flammable refrigerant, classified
as Class 3 “Higher Flammability” by ASHRAE34) and were evaluated following
additional requirements of Supplement SA of UL 250. The cooling system is
considered a protected cooling system.

Models CF2137, UF-304W, UF-304SS, CUF-301, MRF-161, WHS-109FW1, WHS­109FB1, WHS-109FSS1, CUF30M1W, KTUF88, CUF-301BK, UF300WE, FC-1301K, FC-1300W,
ARU03M2AWW are identical to HS-109FN(SNZ) except model designation.

Models MUFM011AEW, MUFM011AEB, MUFM011AES, MUFM011AET, AUFM011AEB,
AUFM011AES, AUFM011AET, FKAUFM011AEW, FKAUFM011AEB, FKAUFM011AES,
FKAUFM011AET, BAUFM011AEW, BAUFM011AEB, BAUFM011AES, BAUFM011AET,
MNAUFM011AEW, MNAUFM011AEB, MNAUFM011AES, MNAUFM011AET, UF-114W, UF-114SS,
CMF151L, CRF150SS, CUF-110, CMF151L-1, CRF150SS-1, WHS-52FW1, WHS-52FB1, WHS­52FSS1, CUF-110, AUFM011AEW, AUFM011AEOT are identical to HS-52FN(SNZ)
except model designation.

File SA12879 Vol. 1 Sec. 7 Page 1A Issued: 2013-11-20

and Report Revised: 2021-11-12

Models NS-CZ35WH7, NS-CZ35WH7-C, WHS-129C1WSB, WHS-129C1, KTCF99,
ACFM035ADW, ACFM035BDW, ACFM035ADOT, HME030048N, CR350, 3W1CF35 are identical
to HS-129CN(NZ) except model designation.

Model HS-129CN(SNZ) is identical to HS-129CN(NZ) except model
designation, electrical rating and compressor.

Model URBD99DE, WHS-129C1W are identical to HS-129CN(SNZ) except model
designation.

Model HS-52FN(S2NZ) is identical to HS-52FN(SNZ) except compressor and
model designation.

Models ARU030S1ARWW, MRU03M2ABB and ARU030S1ARSS are identical to HS­109FN(SNZ) except model designation.

Models NS-UZ7WH0, MRU07M2AWW, CU7DSWBR1RCM are identical to HS-255FN(NZ)
except model designation.

Models AUFM011AEW, MRU01M3AWW, MRU01M3ABB, MRU01M3ASL, FC-1110K, FC­1110W are identical to model HS-52FN(S2NZ) except model designation.

Model CUF-301SS is identical to model HS-109FN(SNZ) except model
designation.

Model DSD-109MU is identical to model HS-109FN(SNZ) except model
designation.

Model MDUF3**(* can be WH/BK/SS as different color of the same model)
is identical to model HS-109FN(SNZ) except model designation.

Models MDUF7WH and MDUF7SS are identical to model HS-255FN(NZ) except
model designation.

Model HS-109FN(S2NZ) is identical to model HS-109FN(SNZ) except model
designation and compressor.

Model HS-255FN(2NZ) is identical to model HS-255FN(NZ) except model
designation and physical size.

Model MDUFC7SS is identical to model HS-255FN(2NZ) except model
designation.

Models CUF-301BK, CUF-301SS, ARU030S1ARWW, ARU030S1ARSS, WHS-109FW1,
MRU03M2ABB, CUF30M1W, 043-2352-8, KTUF88 are identical to model HS-109FN(S2NZ)
except model designation.

Models H11MFW, H11MFB, H11MFS are identical to model HS-52FN(S2NZ）
except model designation.

File SA12879 Vol. 1 Sec. 7 Page 1B Issued: 2013-11-20

and Report Revised: 2021-10-11

TECHNICAL CONSIDERATIONS (NOT FOR FIELD REPRESENTATIVE USE):

* Products designated USL have been investigated using requirements
contained in the Standard for Safety Of Household And Similar Appliances –
Part 1 :General Requirements, UL 60335-1, Sixth Edition, Revision Date 2016-
10-31 and Particular Requirements for Refrigerating Appliances, Ice-Cream
Appliances and Ice-Makers, UL 60335-2-24, Second Edition, Revision Date 2020-

02-27.

* Products designated CNL have been investigated using requirements
contained in Standard for Safety Of Household And Similar Appliances – Part
1 :General Requirements, CAN/CSA C22.2 NO. 60335-1:16, Second Edition,
Revision Date 2016-10-31 and Particular Requirements for Refrigerating
Appliances, Ice-Cream Appliances and Ice-Makers, CAN/CSA C22.2 No. 60335-2­24:17, Second Edition, Revision Date 2020-02-27.

RATINGS:

See MARKING.

INSTRUCTIONS:

Each unit is provided with instruction manual.

*

Cord connected units only.

CONSTRUCTION DETAILS:

Electrical Spacings - Unless otherwise noted in this Report, the
spacings between uninsulated live parts of opposite polarity and between
uninsulated live parts and dead-metal parts are not less than 1/8 in. through
air, 1/4 in. oversurface, and 1/4 in. to the enclosure.

File SA12879 Vol. 1 Sec. 7 Page 1C Issued: 2013-11-20

and Report New: 2021-10-11

The instruction shall provide the following information.

1. A child entrapment warning statement shall be included in either the
operating instructions or in a use and care manual provided with each
refrigerator and shall include the following or equivalent wording:
WARNING: Risk of child entrapment. Before you throw away your old
refrigerator or freezer:

Take off the doors.
Leave the shelves in place so that children may not easily climb inside.

2. The instructions for COMPRESSION-TYPE APPLIANCES that use FLAMMABLE
REFRIGERANTS shall additionally include the substance of the warnings listed
below:
– WARNING: Keep ventilation openings, in the appliance enclosure or in the
built-in structure, clear of obstruction.
– WARNING: Do not use mechanical devices or other means to accelerate the
defrosting process, other than those recommended by the manufacturer.
– WARNING: Do not damage the refrigerant circuit.
– WARNING: Do not use electrical appliances inside the food storage
compartments of the appliance, unless they are of the type recommended by the
manufacturer.

For units to be sold in Canada, instruction shall be in English and French.

File SA12879 Vol. 1 Sec. 7 Page 2 Issued: 2013-11-20

10-5 Nameplate Marking

Recognized (PGDQ2, 8)

*Model

HS-109FN(SNZ)

HS-52FN(SNZ)#

HS-129CN(NZ)*

Material

Any R/C suitable for the mounting surface

Manufacturer

Various

Recognized Designation

Various

Location

Unit Rear or Side

Secured By

Adhesive

Listee's Name

Hefei Hualing Co., Ltd.

Refrigerant

- Type

R600a

R600a

R600a

- Amount, oz (g)

1.59 (45)

0.92 (26)

1.34 (38)

Design Pressure

High Side, psig

180

150

150

Low Side, psig

606060

Electrical Rating

V

115 Vac

115 Vac

115 Vac

A - Total

1.1

1.1

1.2

Frequency, Hz

606060

Date Code

See Sec. Gen for details

Model

HS-129CN(SNZ)

HS-255FN(NZ)

HS-52FN(S2NZ)

Material

Any R/C suitable for the mounting surface

Manufacturer

Various

Recognized Designation

Various

Location

Unit Rear or Side

Secured By

Adhesive

Listee's Name

Hefei Hualing Co., Ltd.

Refrigerant

- Type

R600a

R600a

R600a

- Amount, oz (g)

1.48 (42)

2.65 (75)

0.92 (26)

Design Pressure

High Side, psig

150

150

160

Low Side, psig

606070

Electrical Rating

V

115 Vac

115 Vac

115 Vac

A - Total

1.1

1.5

1.1

Frequency, Hz

606060

Date Code

See Sec. Gen for details

and Report Revised: 2020-08-21

10 MARKING:

- This model employed two alternate compressors (model FZ40E1J manufactured
by Anhui Meizhi Compressor Co., Ltd. And model DG40BY1B manufactured by
HUANGSHI DONGBEI ELECTRICAL APPLIANCE CO LTD) with the same electrical rating.

# - The model HS-52FN(SNZ) employed two alternate compressors (model FZ40E1J
manufactured by Anhui Meizhi Compressor Co., Ltd and model FZ35C1M
manufactured by Anhui Meizhi Compressor Co., Ltd) with the same electrical
rating

File SA12879 Vol. 1 Sec. 7 Page 2A Issued: 2013-11-20

10-5 Nameplate Marking

Recognized (PGDQ2, 8)

Model

HS-109FN(S2NZ)

HS-255FN(2NZ)

Material

Any R/C suitable for the mounting surface

Manufacturer

Various

Recognized Designation

Various

Location

Unit Rear or Side

Secured By

Adhesive

Listee's Name

Hefei Hualing Co., Ltd.

Refrigerant

- Type

R600a

R600a

- Amount, oz (g)

1.62 (46)

2.12 (60)

Design Pressure

High Side, psig

N/A

N/A

Low Side, psig

N/A

N/A

Electrical Rating

V

115 Vac

115 Vac

A - Total

0.8

1.5

Frequency, Hz

60

60

Date Code

See Sec. Gen for details

and Report Revised: 2021-03-18

10 MARKING(Cont’d):

File SA12879 Vol. 1 Sec. 7 Page 3 Issued: 2013-11-20

Model

All

*

A. Type or Material

Manufacturer

See Section General

Recognized Designation

See Section General

Location

Unit Rear, above machine compartment

Quote Marking

*

1) DANGER – Risk of fire or explosion. Flammable refrigerant used. To be
repaired only by trained service personnel. Use only manufacturer-authorized
service parts. Any repair equipment used must be designed for flammable
refrigerants. Follow all manufacturer repair instructions. Do not puncture
refrigerant tubing.

The above symbol shall be at least 15 mm.

*

2) CAUTION - Risk Of fire or explosion. Dispose of refrigerator properly in
accordance with the applicable federal or local regulations. Flammable
refrigerant used.

*

3) CAUTION - Risk of fire or explosion due to puncture of refrigerant tubing;
follow handling instructions carefully. Flammable refrigerant Used.

*

* Comments

The markings shall be in letters no
less than 3.2 mm high.

“DANGER”, “WARNING”, and “CAUTION” no
less than 5.0 mm high.

B. Type or Material

Manufacturer

See Section General

Recognized Designation

See Section General

* Location

evaporator that can be contacted by

the user.

Quote Marking

*

DANGER - Risk of fire or explosion. Flammable refrigerant used. Do not use
mechanical devices to defrost refrigerator. Do not puncture refrigerant
tubing.

comments

The markings shall be in letters no
less than 3.2 mm high.
“DANGER”, “WARNING”, and “CAUTION” no
less than 5.0 mm high.

and Report Revised: 2016-09-28

10-10 Special Marking

File SA12879 Vol. 1 Sec. 7 Page 3A Issued: 2013-11-20

Model

HS-129CN(NZ), HS-109FN(SNZ), HS­52FN(SNZ), HS-52FN(S2NZ), HS-129CN(SNZ)

*A.

Type or Material

Manufacturer

See Section General

Recognized Designation

See Section General

Location

Lock key and near key slot

Quote Marking



CAUTION – To Prevent A Child From Being
Entrapped, Keep Out Of Reach Of Children
And Not In The Vicinity Of Freezer (or

Refrigerator)”

Comment

Optional, for models with door lock
construction only. The key slot is spring
loaded or equivalent so that the key must
be manually held in the lock in any
position of the lock.

Model

HS-129CN(SNZ)

B.

Type or Material

Manufacturer

Various

Recognized Designation

Various

Location

Control Enclosure near lampholder

Quote Marking



Max 15 W”

Model

All

C.

Type or Material

Manufacturer

See Section General

Recognized Designation

See Section General

Location

Unit side or Unit Rear

Quote Marking

CYCLOPENTANE

Comments

The markings shall be in letters no less
than 40 mm high.

and Report Revised: 2021-10-11

10-10 Special Marking (Cont’d)

File SA12879 Vol. 1 Sec. 7 Page 4 Issued: 2013-11-20

Model

HS-109FN(SNZ)

HS-52FN(SNZ),
HS-52FN(S2NZ)

HS-129CN(NZ),
HS-129CN(SNZ)

Approximate Physical Size
(including door lid), W x H
x D, mm.

500 x 848 x
542

470 x 482 x
442

565 x 850 x
523
Model

HS-255FN(NZ)

HS-109FN(S2NZ)

HS-255FN(2NZ)

Approximate Physical Size
(including door lid), W x H
x D, mm.

545 x 1425 x
565

501 x 860 x
540

550 x 1430 x
570

*Model

All

Material

Steel

Thickness, mm.

Min 0.20 mm

Corrosion Protection
(Method)

Paint Coating

Bonding for Grounding
(Method)

Screw connected with grounding conductor of the
power cord.

Model

All except models HS-255FN(NZ), HS-255FN(2NZ)

Material

Steel

Thickness, Min. mm.

0.35 mm

Corrosion Protection
(Method)

Paint Coating

Bonding for Grounding
(Method)

Screw-connected with unit base.
Model

HS-255FN(NZ), HS-255FN(2NZ)

Material

Steel

Thickness, Min. mm.

0.4 mm

Corrosion Protection
(Method)

Paint Coating

Bonding for Grounding
(Method)

Screw-connected with unit base.

and Report Revised: 2021-03-18

20 ENCLOSURES:

20-5 Ultimate Enclosure

20-10 Unit Base

20-15 Unit Sides

20-15 Unit Sides

File SA12879 Vol. 1 Sec. 7 Page 4A Issued: 2013-11-20

Model

HS-52FN(SNZ), HS-52FN(S2NZ)

Material

Steel

Thickness, Min. mm.

0.35mm

Corrosion Protection
(Method)

Paint Coating

Bonding for Grounding
(Method)

Screw-connected with unit base.

Model

All except model HS-

255FN(NZ), HS­255FN(2NZ)

HS-255FN(NZ), HS­255FN(2NZ)

Material

Steel

Thickness, Min. mm.

0.35 mm

0.32 mm

Corrosion Protection
(Method)

Paint Coating

Bonding for Grounding
(Method)

Integral with unit sides.

and Report Revised: 2021-03-18

20-15 Alternate Unit Sides

20-20 Unit Top

File SA12879 Vol. 1 Sec. 7 Page 5 Issued: 2013-11-20

Model

HS-52FN(SNZ),
HS-52FN(S2NZ)

HS-129CN(NZ),
HS-129CN(SNZ)

HS-255FN(NZ),
HS-255FN(2NZ)

Material

Galvanized Steel

Thickness, mm.

Min. 0.35 mm

0.32 mm

Compressor Compartment
Opening, H x W, mm

214 x 467

560 x 772

222 x 465

Model

HS-109FN(SNZ)

HS-52FN(SNZ),
HS-52FN(S2NZ)

HS-129CN(NZ),
HS-129CN(SNZ)

Material

Polymeric

Manufacturer

Hefei Chenyuan Industry and Trade Co., Ltd.

Designation

PVC

Thickness, mm.

0.7 mm

Size, H x W, mm

490 x 1430

465 x 980

455 x 325
(Base)

Comments

The radiant panel test have been done under
SR10267598; also refer to Test Reference No. 2
in SA12508, Vol. 1, Sec. 14.

Alternate Manufacturer 1

HF MeiLian Metal Pressing Process Co., Ltd.

Alternate Designation 1

PVC-sg5y

Thickness, mm.

0.8 mm

Alternate Manufacturer 2

Zhongshan Panshun Plastic Co., Ltd.

Alternate Designation 2

PS-v02

Thickness, mm.

0.8 mm

Comments

The radiant panel test have been done under
Project No. 4786575151; also refer to Test
Record No. 4 in SA12879, Vol. 1, Sec. 8.

Alternate Manufacturer 3

HF MeiLian Metal Pressing Process Co., Ltd.

Alternate Designation 3

PVC-sg5y

Thickness, mm.

0.8 mm

Comments

The radiant panel test have been done under
Project No. 4786575151; also refer to Test
Record No. 4 in SA12879, Vol. 1, Sec. 8.

and Report Revised: 2021-03-18

20-25 Unit Rear

20-25 Alternate Unit Rear or Base, same as above except:

20-25 Alternate Unit Rear, same as above, except:

20-25 Alternate Unit Rear, same as above, except:

File SA12879 Vol. 1 Sec. 7 Page 5A Issued: 2013-11-20

Model

HS-255FN(NZ), HS-255FN(2NZ)

Material

Polymeric

Manufacturer

Hefei Chenyuan Industry and Trade Co., Ltd.

Designation

PVC

Thickness, mm.

0.7 mm

Size, H x W, mm

222 x 465

Comments

The radiant panel test has been done with
satisfactory result under UL project
No.SR10267598 according to ASTM E162.

Alternate Manufacturer 1

HF MeiLian Metal Pressing Process Co., Ltd.

Alternate Manufacturer 2

Zhongshan Panshun Plastic Co., Ltd.

Alternate Manufacturer 3

Qingdao tianfule Plastic Co.,Ltd Hefei Branch.

Designation

PVC

Thickness, mm.

0.8 mm

Comments

The radiant panel test has been done with
satisfactory result under UL project No.
4786575151 and No. 4786893908 according to ASTM
E162.

Model

HS-52FN(SNZ), HS-52FN(S2NZ)

Material

Polymeric

Steel

Manufacturer

Hefei Chenyuan Industry and Trade Co., Ltd.

Designation

PVC

N/A

Thickness, mm.

0.7 mm

Min. 0.35 mm

Size, H x W x D, mm

201 x 464 x 326

Comments

The radiant panel test has been done with
satisfactory result under UL project
No.SR10267598 according to ASTM E162.

and Report Revised: 2021-03-18

20-25 Alternate Unit Rear or Base, same as above except:

20-25 Alternate Unit Rear, same as above, except:

20-25 Alternate Unit Rear or Base, same as above except:

File SA12879 Vol. 1 Sec. 7 Page 5A Issued: 2013-11-20

Model

All except HS-129CN(NZ), HS-129CN(SNZ)

Material

Polymeric, See Sec. 30 for details

Model

HS-129CN(NZ), HS-129CN(SNZ)

Material

Aluminum

Galvanized Steel with
painting

Thickness, mm

0.32 mm

0.35 mm

Model

All

Material

Steel

Thickness, mm.

0.35 mm

Corrosion Protection
(Method)

Paint Coating

Bonding for Grounding
(Method)

Not required, no electrical components in door.
Model

All

Material

Polymeric, See Sec. 30 for details

Model

All

*Material

CYCLOPENTANE

Where Used

Inside cabinet liner

Comments

All entrance and exit holes for wiring (all the
employed wiring are VW-1 rated) or foaming are
sealed with caps or permagum.

and Report Revised: 2021-10-11

20-30 Cabinet Liner

20-30 Cabinet Liner

20-35 Unit Door

20-40 Cabinet Door Liner

20-45 Thermal Insulation

File SA12879 Vol. 1 Sec. 7 Page 6 Issued: 2013-11-20

Model

All

Material

Galvanized Steel

Model

All except
HS-129CN(NZ),
HS-129CN(SNZ)

HS-129CN(NZ),
HS-129CN(SNZ)
Type

Magnetic gasket

Gasket

Model

HS-109FN(SNZ)

Location

Inside machine compartment

Material

Polymeric, See Sec. 30 for details

Thickness, mm.

1.5 mm

Method of Securement

Two screws connected to steel cabinet rear

Dimension, H x W x D, mm.

100 x 57 x 45

Components Within

Temperature Controller

Comments

The 0.2 mm metal foil is attached inside
control cover.

Model

HS-52FN(SNZ), HS-52FN(S2NZ)

Location

Front

Liner in refrigerated compartment

Rear Cover

Machine compartment

Material

Polymeric, See Section 30 for details

Method of Securement

Rear Cover

Two screws to steel cabinet rear

Openings, Number

None

Dimension, H x W x D, mm

89 x 38 x 51

Corrosion Protection

Inherent

Bonding for Grounding

None Required

Components Within

Thermostat, wiring

and Report Revised: 2019-12-25

20-50 Door Hinges

20-55 Door Latching Device

20-60 Control Enclosure

File SA12879 Vol. 1 Sec. 7 Page 6A Issued: 2013-11-20

Model

HS-129CN(NZ), HS-129CN(SNZ)

Location

Inside machine compartment

Material

Polymeric, See Sec. 30-1

Thickness, mm.

2.0 mm

Method of Securement

Two screws connected with control panel

Components Within

Temperature Controller

Model

HS-255FN(NZ), HS-255FN(2NZ)

Location

Inside machine compartment

Material

Polymeric, See Sec. 30-1

Thickness, mm.

Min 1.5

*Method of Securement

Snap joint to control panel

Components Within

Temperature Controller

Model

HS-129CN(NZ), HS-129CN(SNZ)

Location

Unit front

Material

Polymeric, See Sec. 30-1

Thickness, mm.

2.0 mm

Method of Securement

Clamped into unit side and connected with
control enclosure with 2 screws.

Openings, Number and Size

See Ill. 6 for details

Location of Openings

On the side of Control Panel

Components Within

Fast-freeze switch, power indicator light and
compressor running indicator light

Model

HS-129CN(NZ), HS-129CN(SNZ)

Location

Unit front

Material

Polymeric, See Sec. 30-1

Thickness, mm.

2.0 mm

Method of Securement

Clamped into unit side and connected with
control enclosure with 2 screws.

Openings, Number and Size

See Ill. 7 and 7A for details

Location of Openings

On the side of Control Panel

and Report Revised: 2021-03-18

20-60 Control Enclosure

20-60 Control Enclosure

20-65 Control Panel

20-65 Alternate Control Panel

File SA12879 Vol. 1 Sec. 7 Page 6B Issued: 2013-11-20

Model

HS-255FN(NZ), HS-255FN(2NZ)

Location

Inside machine compartment

Material

ABS

Flammability Rating

HB

Thickness, mm.

Min 1.5

Method of Securement

Secured by two screws to let side of inner
liner.

Dimensions, H x W x D, mm

478.5 x 47.7 x 101.3

Openings, Number and Size

See Test Reference ILL. 2 Photo 12 and Test
Reference ILL. 3 for details

Location of Openings

On the side of Control Panel

Components Within

Temperature Controller Switch

and Report Revised: 2021-03-18

20-65 Control Panel (Horizontal beam):

File SA12879 Vol. 1 Sec. 7 Page 6B Issued: 2013-11-20

Model

HS-129CN(NZ), HS-129CN(SNZ)

Material

Steel

Thickness, mm.

0.45

Location and Dimension

See Fig. 5 and Ill. 9 for details

Model

HS-129CN(NZ), HS-129CN(SNZ)

Material

Polymeric, See Sec. 30-1

Thickness, mm.

2.0

Location and Dimension

See Fig. 5A and Ill. 9A for details

Model

HS-129CN(NZ), HS-129CN(SNZ)

Material

Polymeric, See Sec. 30-1

Thickness, mm.

2.0 mm

Location and Dimension

See Fig. 6 and Ill. 10 for details

Comments

This shutter is used for air ventilation and
power cord passage.

Model

HS-255FN(NZ), HS-255FN(2NZ)

Material

Polymeric, See Sec. 30-1

Dimension, L x W x H, mm

153.5 x 125.0 x 60.0

Thickness, mm.

1.5

Location

Machine compartment, below compressor

and Report Revised: 2021-03-18

20-70 Machine Compartment Cover

20-70 Alternative Machine Compartment Cover

20-75 Shutter (optional)

20-80 Drip Pan

File SA12879 Vol. 1 Sec. 7 Page 7 Issued: 2013-11-20

Model

All

Cabinet Liner/Door Liner (Vacuum Formed)

Recognized (QMFZ2, 8)

Manufacturer

Various

Material Designation

Various

Thickness, mm. (minimum) +

Minimum recognized thickness

Flammability Classification

(minimum)

HB
Control Enclosure, Wiring Box/Cover

Recognized (QMFZ2, 8)

Manufacturer

LG Chemical Ltd.

Material Designation

AF360(#), AF305(#), AF315

Thickness, mm. (minimum)

2.5

Flammability Classification

(minimum)

5VA

Control Panel for model HS-129CN(NZ)/HS­129CN(SNZ) only

Recognized (QMFZ2, 8)

Manufacturer

POLYROCKS
CHEMICAL CO LTD

Material Designation

7001(+)

Thickness, mm. (minimum)

2.0

Flammability Classification (minimum)

5VA

and Report Revised: 2016-09-28

30 NONMETALLIC COMPONENTS:

File SA12879 Vol. 1 Sec. 7 Page 7A Issued: 2013-11-20

Strain-relief Means for model
HS-129CN(NZ)/HS-129CN(SNZ) only

Recognized (QMFZ2)

Manufacturer

NINGBO LG YONGXING CHEMICAL CO LTD

Material Designation

FR-500A

Thickness, mm. (minimum)

3.0

Flammability Classification

(minimum)

V-0

Door Hinge Guard for model
HS-129CN(NZ)/HS-129CN(SNZ) only

Recognized (QMFZ2, 8)

Manufacturer

NINGBO LG YONGXING CHEMICAL CO LTD

Material Designation

HI-121H

Thickness, mm. (minimum)

1.5

Flammability Classification

(minimum)

HB

Machine Compartment Cover/Shutter for
model HS-129CN(NZ)/HS-129CN(SNZ) only

Recognized (QMFZ2, 8)

Manufacturer

SHANDONG DAWN POLYMER CO LTD

Material Designation

HFPP-01

Thickness, mm. (minimum)

2.0

Flammability Classification

(minimum)

V-0
Model

HS-255FN(NZ), HS-255FN(2NZ)

Cabinet Liner/Door Liner (Vacuum
Formed), Drip Pan

Recognized (QMFZ2, 8)

Manufacturer

Various

Material Designation

Various

Thickness, mm. (minimum) +

Minimum recognized thickness

Flammability Classification

(minimum)

HB
Control Enclosure, Wiring Box/Cover

Recognized (QMFZ2, 8)

Manufacturer

SILVER AGE ENGINEERING PLASTICS
(DONGGUAN) CO LTD.

Material Designation

3370

Thickness, mm. (minimum)

Min 1.5

Flammability Classification

(minimum)

5VA
Model

HS-109FN(SNZ)

All unit wiring is Recognized (AVLV2, 8) and rated VW-1, FT-1 or Listed
SJT(rated FT-1 or FT-2) power cord. All wiring is routed and secured within
the machine compartment or the cabinet liner. All wire splices are totally
insulated and there are no exposed live parts. There are no open coils or
exposed high voltage parts.

and Report Revised: 2021-03-18

30-5 Isolation From Ignition Sources

File SA12879 Vol. 1 Sec. 7 Page 7B Issued: 2013-11-20

30-10 Connection-related nonmetallic
materials

Ref.
Model

Connector
Description

Manufacturer

Manufacturer
Model Number

Location

Housing
Flammability
(minimum)

All

4 pin quick­connector
inside of
machine
compartment

Various

Various

Inside of
machine
compartment,
See Fig. 7
for details

V-0

and Report New: 2019-04-29

The electrical connectors shown below are used in circuits where the total
circuit load is greater than 60W during normal operation and have
materials within the flame cylinder (as defined in UL 60335-2-24 101.DVD.5)
which have required them to be evaluated to the Nichrome Wire Test of UL
60335-2-24 101.DVD.6. The first row is filled in as an example.

File SA12879 Vol. 1 Sec. 7 Page 8 Issued: 2013-11-20

40-5 Condenser (Warm Wall)

Model

HS-109FN(SNZ)

HS-52FN(SNZ),
HS-52FN(S2NZ)

HS-129CN(NZ),
HS-129CN(SNZ)

Manufacturer

Various

N/A

N/A

See Ill. 2 and
2A for details

Mounting (Method)

Foam in place against inside surface of Cabinet

Type of Construction

Tube Type

No. Provided

112

Physical Size, W x H x D,
mm.

487 x 706 x
390

460 x 480 x
335

660 x 525 and
740 x 510

Tubing Material

Steel

Tubing OD, mm.

4.0

Tubing Wall Thickness, mm.

0.5

Total Tube Length, mm.

11130

7374

6076 and 7134

40-5 Condenser (Warm Wall)

Model

HS-255FN(NZ),
HS-255FN(2NZ)

Manufacturer

Various

See Test
Reference ILL.
1

Mounting (Method)

Foam in place against inside surface of Cabinet

Type of Construction

Tube Type

No. Provided

1

Physical Size, mm.

See Test
Reference ILL.
3 for details

Tubing Material

Steel

Tubing OD, mm.

4.0

Tubing Wall Thickness, mm.

0.5

Total Tube Length, mm.

17575

and Report Revised: 2021-03-18

40 REFRIGERATION SYSTEM:

File SA12879 Vol. 1 Sec. 7 Page 8-1 Issued: 2013-11-20

40-5 Alternate Condenser

Model

HS-52FN(SNZ),
HS-52FN(S2NZ)

Manufacturer

Various

*

See Ill. 2B
for details

Mounting (Method)

Foam in place against inside surface of Cabinet

Type of Construction

Tube Type

No. Provided

1

Physical Size, mm.

1330 x 390

Tubing Material

Steel

Tubing OD, mm.

4.0

Tubing Wall Thickness, mm.

0.5

Total Tube Length, mm.

6880

and Report New: 2019-09-06

File SA12879 Vol. 1 Sec. 7 Page 8A Issued: 2013-11-20

40-5A Condenser (Rear Wall)

Model

HS-255FN(NZ),
HS-255FN(2NZ)

Manufacturer

Various

See Test
Reference ILL.
1

Mounting (Method)

Held in place by aluminium adhesive foil and
foamed in place.

Type of Construction

Tube Type

No. Provided

1

Physical Size, mm.

See Test
Reference ILL.
3 for details

Tubing Material

Galvanized steel

Tubing OD, mm.

4.0

Tubing Wall Thickness, mm.

0.5

Total Tube Length, mm.

8970

40-5B Condenser (Anti-sweet)

Model

HS-255FN(NZ),
HS-255FN(2NZ)

Manufacturer

Various

See Test
Reference ILL.
1

Mounting (Method)

Held in place by aluminium adhesive foil and
foamed in place.

Type of Construction

Tube Type

No. Provided

1

Physical Size, mm.

See Test
Reference ILL.
3 for details

Tubing Material

Galvanized steel

Tubing OD, mm.

4.0

Tubing Wall Thickness, mm.

0.5

Total Tube Length, mm.

8970

and Report Revised: 2021-03-18

File SA12879 Vol. 1 Sec. 7 Page 9 Issued: 2013-11-20

40-10 Evaporator

Model

HS-109FN(SNZ)

HS-52FN(SNZ),
HS-52FN(S2NZ)

HS-129CN(NZ),
HS-129CN(SNZ)

Manufacturer

Various

See Ill. 3 for
details

N/A

See Ill. 3A
for details

Corrosion Protection
(Method)

Inherent

Mounting (Method)

Screws to Cabinet liner with metal backup
plates

Bonding for Grounding
(Method)

Through tubing to compressor
Type of Construction

Roll Bond

Dimensions, W x H x D, mm.

375 x 705 x
330

360 x 334 x
340

448 x 383 x
695

Material

Aluminum

Tubing OD, mm.

8.0

6.0

7.0

Tubing Wall Thickness, mm.

0.71

0.75

0.75

Total Tube Length, mm.

13290

15700

19900

40-10 Evaporator

Model

HS-255FN(NZ)

HS-255FN(2NZ)

Manufacturer

Various

Corrosion Protection
(Method)

Inherent

Mounting (Method)

Wrap around Cabinet liner by aluminum adhesive
foil and foamed in place.

Bonding for Grounding
(Method)

Through tubing to compressor
Type of Construction

Roll Bond

Dimensions, mm.

See Test Reference ILL. 3 for
details

Material

Aluminum

Tubing OD, mm.

7.5

Tubing Wall Thickness, mm.

0.75

Total Tube Length, mm.

8970

24000

and Report Revised: 2021-03-18

File SA12879 Vol. 1 Sec. 7 Page 10 Issued: 2013-11-20

40-10 Alternate Evaporator

Model

HS-52FN(SNZ),
HS-52FN(S2NZ)

Manufacturer

See Ill. 3B
for details

Corrosion Protection
(Method)

Inherent

*Mounting (Method)

Wrap around Cabinet liner by aluminum adhesive
foil and foamed in place.

Bonding for Grounding
(Method)

Through tubing to compressor
Type of Construction

Roll Bond

Dimensions, mm.

360 x 334 x
340

Material

Aluminum

Tubing OD, mm.

7.0

Tubing Wall Thickness, mm.

0.75

Total Tube Length, mm.

9150

Model

All

Means Provided

Soldered or Brazed Joint

Location

All tube connections

Model

All

*Manufacturer

Various

*

Material

Copper

Length, mm.

100.0 or 105.0

OD, mm.

19.0

Wall Thickness, mm.

0.5

Location

High side of refrigeration system- Right side
machine compartment

Corrosion Protection
(Method)

Inherent

and Report Revised: 2019-09-06

40-15 Pressure Relief

40-20 Drier/Filter

File SA12879 Vol. 1 Sec. 7 Page 11 Issued: 2013-11-20

Model

All

Material

Copper

Outside Diameter,

mm.

Minimum Wall Thickness,

mm.

6.0

0.65

Model

HS-109FN(SNZ)

HS-52FN(SNZ),
HS-52FN(S2NZ)

HS-129CN(NZ),
HS-129CN(SNZ),

HS-255FN(NZ),
HS-255FN(2NZ)

Capillary Tube - No.
Provided

1

Material

Copper

ID, mm.

0.6

Wall Thickness, mm.

0.6

Length, mm.

2640

2200

3000

Model

All

Method of Joining

Soldered or brazed connections

Model

All

Manufacturer

CHANG SHA HURGE INDUSTRIAL CO., LTD.

Usage

Condenser

Evaporator

Designation

21#

20#

Material

Stainless Steel

Aluminum Alloy

OD, mm.

7.8

11

Wall thickness, mm.

1.625

1.85

Location

Machine compartment

Corrosion protection
(method)

Inherent

and Report Revised: 2021-03-18

40-25 Interconnecting Tubing

40-30 Refrigerant Control

40-35 Refrigeration System Joints

Note: Copper-aluminum transition joints are painted to prevent galvanic

corrosion.

40-40 Refrigerant Tubing Connector (Optional)

File SA12879 Vol. 1 Sec. 7 Page 12 Issued: 2013-11-20

50-5A Compressor

Recognized (SLIS2, 8)

Model

HS-109FN(SNZ), HS-52FN(SNZ), HS­129CN(NZ)

Manufacturer

Anhui Meizhi Compressor Co., Ltd.

Designation

FZ40E1J

Electrical Rating

Volts

115 Vac

RLA (Not for Inspector Use)

0.66

* LRA

5

Phase

1

Cycle

60

Bonding for Grounding (Method)

No. 18 AWG green colored ground wire
from compressor terminal block to unit
base. Each end of the ground wire is
secured with a closed eyelet and screw
with nut. Eyelets on painted surfaces
are provided with serrated-head
washers to break the paint.

Overload Protector(+)

External

Manufacturer

Hang Zhou Star Shuaier Electric
Appliance Co., Ltd.

Designation

DRB17N61A1

Alternate Manufacturer

SENSATA TECHNOLOGIES (E15962)

Designation

4TM158NFBYY

Location

Compressor Terminal Enclosure

Compressor Start Assist Device(+)

Recognized (SDFY2, 8)

Type

PTC Type

Manufacturer

Hang Zhou Star Shuaier Electric
Appliance Co., Ltd.

Designation

QP2-4R7 or QP2-4R7 K

Alternate Manufacturer

SENSATA TECHNOLOGIES (SA3745)

Designation

8EA14C1

Location

Inside Compressor Terminal Cover

and Report Revised: 2021-05-11

50 MOTOR - COMPRESSOR ASSEMBLY:

(+) - Part of Recognized motor-compressor assembly.

File SA12879 Vol. 1 Sec. 7 Page 12A Issued: 2013-11-20

50-5B Compressor

Recognized (SLIS2, 8)

Model

HS-129CN(SNZ)

Manufacturer

Anhui Meizhi Compressor Co., Ltd

Designation

FZ40C1J

Electrical Rating

Volts

115 Vac

RLA (Not for Inspector Use)

0.67

LRA

6

Phase

1

Cycle

60

Bonding for Grounding (Method)

No. 18 AWG green colored ground wire
from compressor terminal block to unit
base. Each end of the ground wire is
secured with a closed eyelet and screw
with nut. Eyelets on painted surfaces
are provided with serrated-head
washers to break the paint.

Overload Protector(+)

External

Manufacturer

HANG ZHOU STAR SHUAIER ELECTRIC
APPLIANCE CO LTD

Designation

DRB20T61A1

Location

Compressor Terminal Enclosure

Compressor Start Assist Device(+)

Recognized (SDFY2, 8)

Type

PTC Type

Manufacturer

HANG ZHOU STAR SHUAIER ELECTRIC
APPLIANCE CO LTD

Designation

QP2-4R7

Location

Inside Compressor Terminal Cover

and Report New: 2016-09-28

50 MOTOR - COMPRESSOR ASSEMBLY:

(+) - Part of Recognized motor-compressor assembly.

File SA12879 Vol. 1 Sec. 7 Page 12B Issued: 2013-11-20

50-5B Compressor

Recognized (SLIS2, 8)

Model

HS-129CN(NZ)

Manufacturer

HUANGSHI DONGBEI ELECTRICAL
APPLIANCE CO LTD

Designation

DG40BY1B

Electrical Rating

Volts

115 Vac

RLA (Not for Inspector Use)

0.75

LRA

11.8

Phase

1

Cycle

60

Bonding for Grounding (Method)

No. 18 AWG green colored ground wire
from compressor terminal block to unit
base. Each end of the ground wire is
secured with a closed eyelet and screw
with nut. Eyelets on painted surfaces
are provided with serrated-head
washers to break the paint.

Overload Protector(+)

External

Manufacturer

HANG ZHOU STAR SHUAIER ELECTRIC
APPLIANCE CO LTD

Designation

DRB21N61A

Location

Compressor Terminal Enclosure

Compressor Start Assist Device(+)

Recognized (SDFY2, 8)

Type

PTC Type

Manufacturer

HANG ZHOU STAR SHUAIER ELECTRIC
APPLIANCE CO LTD

Designation

QPS2-B4R7MG1

Location

Inside Compressor Terminal Cover

and Report New: 2016-12-20

50 MOTOR - COMPRESSOR ASSEMBLY:

(+) - Part of Recognized motor-compressor assembly.

File SA12879 Vol. 1 Sec. 7 Page 12C Issued: 2013-11-20

Rating, uF, V

N/A

and Report Revised: 2021-05-11

50 MOTOR--COMPRESSOR ASSEMBLY

50-5 Compressor Recognized (SLIS2, 8)

Model HS-52FN(SNZ), HS-52FN(S2NZ)
Manufacturer Anhui Meizhi Compressor Co., Ltd.

Designation FZ35C1M
Electrical Rating

Volts 115
Phase 1
Cycle 60
LRA 5
RLA 0.73
Bonding for Grounding Bonded to the unit base through
(method) a No. 18 AWG eyelet connectors

and screws.

50-10 Overload Protector (+) External

Manufacturer Hang Zhou Star Shuaier Electric

Appliance Co., Ltd.
Designation DRB18T61A1
Location Compressor terminal enclosure
Comments This model was evaluated according

to IEC 60079-15 for ignition

protection

50-15 Compressor Start Assist Device (+) External

Manufacturer Hang Zhou Star Shuaier Electric

Appliance Co., Ltd.
Designation QP2-4R7 or QP2-4R7 K
Location Compressor terminal enclosure

50-20 Running Capacitor - Recognized (CYWT2, 8)

(+) - Part of Recognized Motor-Compressor Assembly.

File SA12879 Vol. 1 Sec. 7 Page 12D Issued: 2013-11-20

50-5A Compressor

Recognized (SLIS2, 8)

Model

HS-255FN(NZ), HS-255FN(2NZ)

Manufacturer

Anhui Meizhi Compressor Co., Ltd.

Designation

EZ75E1B-U

Electrical Rating

Volts

115-127 Vac

RLA (Not for Inspector Use)

0.95

LRA

10.7

Phase

1

Cycle

60

Bonding for Grounding (Method)

No. 18 AWG green colored ground wire
from compressor terminal block to unit
base. Each end of the ground wire is
secured with a closed eyelet and screw
with nut. Eyelets on painted surfaces
are provided with serrated-head
washers to break the paint.

Overload Protector(+)

External

Manufacturer

Hang Zhou Star Shuaier Electric
Appliance Co., Ltd.

Designation

DRB31T61A1

Location

Compressor Terminal Enclosure

Compressor Start Assist Device(+)

Recognized (SDFY2, 8)

Type

PTC Type

Manufacturer

Hang Zhou Star Shuaier Electric
Appliance Co., Ltd.

Designation

QP2-4R7 or QPE2-A4R7MD3

Location

Inside Compressor Terminal Cover

and Report Revised: 2021-03-18

50 MOTOR - COMPRESSOR ASSEMBLY:

(+) - Part of Recognized motor-compressor assembly.

File SA12879 Vol. 1 Sec. 7 Page 12E Issued: 2013-11-20

50-5 Compressor

Recognized (SLIS2, 8)

Model

HS-109FN(S2NZ)

Manufacturer

Sichuan Danfu Environment Technology
Co.,Ltd (SA12717)

Designation

DFB30DF

Electrical Rating

Volts

110-120

RLA (Not for Inspector Use)

0.49

LRA

5.5

Phase

1

Cycle

60

Bonding for Grounding (Method)

No. 18 AWG green colored ground wire
from compressor terminal block to unit
base. Each end of the ground wire is
secured with a closed eyelet and screw
with nut. Eyelets on painted surfaces
are provided with serrated-head
washers to break the paint.

Overload Protector(+)

External

Manufacturer

Hang Zhou Star Shuaier Electric
Appliance Co., Ltd. (E213160)

Designation

DRB16N61A1

Location

Compressor Terminal Enclosure

Compressor Start Assist Device(+)

Recognized (SDFY2, 8)

Type

PTC Type

Manufacturer

Hang Zhou Star Shuaier Electric
Appliance Co., Ltd. (E232371)

Designation

QP2-4R7

Location

Inside Compressor Terminal Cover

and Report New: 2021-02-04

50 MOTOR - COMPRESSOR ASSEMBLY:

(+) - Part of Recognized motor-compressor assembly.

File SA12879 Vol. 1 Sec. 7 Page 13 Issued: 2013-11-20

70-5 Temperature Controller

Recognized (SDFY2, 8)

Model

All

Use (Loads Controlled)

Compressor

A. Manufacturer

ZHEJIANG HUAHENG THERMOSTAT CO.,LTD

Designation

WDF*** Series or WPF*** Series

*Rating, V ac, FLA, LRA

125, 6, 36 or 250, 4, 20

B. Alternate Manufacturer

CHUZHOU JPOLY ELECTRIC FITTING CO LTD

Designation

WPF24-EX, WP0~20, WPF1~38, WDF24-EX,
WD0~4, WDF1~38

Rating, V ac, FLA, LRA

250, 4/6, 24/36

C. Alternate Manufacturer

CHANGZHOU HUISHANG ELECTRIC CO LTD

Designation

WP Series or WD Series or WDvwxy-Lz or

WPvwxy-Lz

Rating, V ac, FLA, LRA

125, 8, 48 or 250, 6, 36

D. Alternate Manufacturer

Jiujiang Hengtai Autocontrol Device
Co., Ltd.

Designation

WP-EX, WPF-EX, WD-EX, WDF-EX

Rating, V ac, FLA, LRA

250, 5(4), 24

E. Alternate Manufacturer

Jiujiang Hengtong Autocontrol Device
Co., Ltd.

Designation

WD, WP, WPF

Rating, V ac, FLA, LRA

250, 6, 36

F. Alternate Manufacturer

CHANGZHOU THERMOSTER ELECTRICAL
APPLIANCE CO LTD

Designation

WDFE, WPFE, WSFE

Rating, V ac, FLA, LRA

250, 6, 24 or 250, 6(4), 16

Location (Physical)

Inside machine compartment and within
thermostat enclosure

Mounting

Screws to thermostat enclosure.

Bonding for Grounding (Method)

A green/yellow ground wire is secured
to the thermostat mounting plate and
to the grounding terminal of the
compressor.

Marked Switch Positions

"Off"

and Report Revised: 2021-03-18

70 ELECTRICAL COMPONENTS:

Note: Located in ungrounded side of power supply

File SA12879 Vol. 1 Sec. 7 Page 13A Issued: 2013-11-20

70-10 Lampholder(Optional)

Recognized (SEVS2, 8)

*Model

HS-129CN(SNZ)

Use (Loads Controlled)

Incandescent lamp

Manufacturer

SHENZHEN GOODPAL ELECTRONICS CO., LTD.

Designation

LHE14-1

Rating, V, W

125, 75

Location (Physical)

Under unit lid

Mounting

Snap in place

Prevented from turning by:

Totally enclosed by lamp guard

Bonding for Grounding (Method)

Not required.

and Report New: 2016-09-28

Note: Located in the ungrounded side of power supply.

File SA12879 Vol. 1 Sec. 7 Page 14 Issued: 2013-11-20

Model

All

Key No.

Wire
Type

(2)

Wire

Style

No. (3)

Minimum

Wire Size

AWG

Insulation (4)

Minimum Wall

Thickness,

in.

Minimum

Temperature

Rating, °C

Minimum

Rating, V

1

AWM

1015180.8

105

300

(1)

Acceptable for refrigeration use, with VW-1 insulation.

(2)

Appliance wiring material, cord type or Listed wire type.

(3)

Applies only to Recognized appliance wiring material.

(4)

Information on the voltage and temperature ratings for the
insulation of wiring that has a marked National Electrical Code Type
designation need not be provided.

and Report Revised: 2013-12-25

80 INTERNAL WIRING:

80-5 Types

Recognized (AVLV2) appliance wiring material(1), Listed cords or Listed

insulated wiring as described below. Wiring which is color-coded green or
green with one or more yellow stripes is employed on grounding conductors
only.

File SA12879 Vol. 1 Sec. 7 Page 15 Issued: 2013-11-20

Model

All

No. From
Previous

Page

Specify the electrical

components connected to

the wiring described

Specify all details of wire routing

including locations and types of clamps,

means of isolating from combustible

materials, Recognized splice and wire

connecting lead terminations, etc.

Key No.

From

To

Details

*

1

Thermostat

Compressor

Routed within machine compartment. Leads
have additional 1.0 mm thick Recognized
(YDPU2) tubing.

1

Thermostat

Lamp

Connected by a quick-connect terminal or
wire nuts.

and Report Revised: 2017-02-17

80-10 Wiring Methods

All wiring is installed and positively routed in such a manner that it

is not subject to mechanical damage due to contact with sharp edges, abrasive
surfaces, vibrating or moving parts. Exposed lengths of ripped parallel
conductors do not exceed 3 in.

Wiring which is completely enclosed within steel conduit, metal

raceways, metallic tubing, cabinet walls, or other separate electrical
enclosures employs 2/64 in. thick (minimum) electrical insulation unless
specified differently in this Report.

Wiring which is not completely enclosed as specified above employs

4/64 in. thick (minimum) electrical insulation unless specified differently
in this Report.

Cords or appliance wiring material employed in the refrigerated

compartment has 4/64 in. thick (minimum) electrical insulation and is located
or protected so as not to be subjected to contact by product containers,
removable shelves, and the like.

Green or green with yellow stripe wire may be employed only as

grounding conductors. Splices are not employed in grounding conductors
unless otherwise noted in the Report.

Holes for the passage of wires or cords through walls, panels or

barriers have smooth, rounded surfaces or are provided with smoothly rounded
bushings.

All splices are mechanically secured to a fixed member or located in a

separate enclosure.

Unless otherwise noted all wires terminate in quick-connect or eyelet

type materials.

Wiring diagram shown in Ill. 1.

Wiring is employed as follows:

File SA12879 Vol. 1 Sec. 7 Page 16 Issued: 2013-11-20

Model

All

Power Supply Cord Set

Listed

Type

SJT

Size, AWG

18 AWG

Attachment Plug Rating, V, A

125 V, 15 A grounding type

Strain Relief Means

By metal clamp and one screw to unit
base Or supply cord is secured to the
machine compartment base with plastic
bushing by screws.

Cord Length, ft

5 Minimum, 10 Maximum

Grounding Conductor Color

Green With or Without Yellow Stripes

Location

Machine compartment base.

Means

Supply cord ground conductor is
secured to the compressor grounding
terminal by a dedicated closed eyelet
and screw.

and Report Revised: 2013-12-25

90 SUPPLY CONNECTIONS:

90-5 Cord Connected Unit

File SA12879 Vol. 1 Sec. 7 Page 17 Issued: 2013-11-20

Model

HS-109FN(SNZ)

A.

Aluminum/Evaporator Tube Shelf

Dimension, L x W, mm.

385 x 310

Aluminum plate thickness, mm.

0.33

No. of shelves

2

Location

Freezer compartment

Method of support

Evaporator coil tubing is attached to
aluminum plate. Plastic inserts are
attached to liner and inserted in
plastic groove. Note an additional
aluminum/evaporator tube plate is
employed on the top internal surface
of unit, to hold evaporator in place
and serve as a restraint for the
removable top drawer/basket

B.

Drawer/Removable Basket

Material

Steel wire with coated plastic and
front plastic cover

No. of drawers/baskets

1

Location

Freezer compartment

Method of restraint

Plastic inserts with stoppers

*Model

HS-52FN(SNZ), HS-52FN(S2NZ)

A.

Wire Shelf

Steel Wire (painted)

Dimension, D x W, mm.

180 x 356

Wire Rod Shelf

Thickness, perimeter wire, mm

4.5

Thickness, mm/No. shelf wires

2.5 / 15

No of shelves

1

Method of Support

Integral to molded liner

Method of Restraint

None required

and Report Revised: 2018-10-19

100 SHELVING AND DRAWERS:

100-5 Shelves (Removable Basket)

File SA12879 Vol. 1 Sec. 7 Page 17A Issued: 2013-11-20

Model

HS-129CN(NZ), HS-129CN(SNZ)

Location

Freezer Food Compartment, right side

Material

Steel

Dimensions, mm. (H x D x W)

173 x 180 x 355

Wire Rod Shelf

Thickness, Perimeter Wire

See Ill. 8 for details

Thickness/No. Shelf Wires

See Ill. 8 for details

No. of Baskets

1

Method of Restraint

Restraint between partition shelf and
right cabinet liner

Model

HS-255FN(NZ)

Wire Shelf

Glass

Dimension, D x W, mm.

397 x 298

400 x 350

400 x 200

Wire Rod Shelf

Thickness, perimeter wire, mm

See Test Reference ILL. 2 Photos 13
and Test Reference ILL. 3 7a,7b,7c for
details

Thickness, mm/No. shelf wires

See Test Reference ILL. 2 Photos 13
and Test Reference ILL. 3 7a,7b,7c for
details

No of shelves

131

Method of Support

Integral to molded liner

Method of Restraint

The glass shelves are rested on inner
liners and held in place by traps in
the inner liner
and stoppers which are integrally
molded to the plastic shelf frames
snapped fitted to
the sides of each glass shelf.

Model

HS-255FN(2NZ)

Dimension, D x W, mm.

400 x 314

400 x 352

400 x 200

No of shelves

141

and Report Revised: 2021-03-18

100-5 Shelves (Removable Basket) (Cont’d)

100-5 Shelves (Cont’d)

100-5 Shelves (Cont’d)

Same as above except:

File SA12879 Vol. 1 Sec. 7 Page 18 Issued: 2013-11-20

and Report Revised: 2021-02-04

Fig. 1 – View of unit front of model HS-109FN(SNZ).

Fig. 2 – View of unit front with door open of model HS-109FN(SNZ).

Fig. 3 – View of unit rear of model HS-109FN(SNZ).

Fig. 4 – View of machine compartment of model HS-109FN(SNZ).

Fig. 5, 5A & 6 – View of Machine Compartment Cover.

Fig. 7 – View of connector location of models HS-52FN(SNZ) and HS-52FN(S2NZ).

Ill. 1, 1A – Nameplate marking including wiring diagram of model HS­109FN(SNZ), HS-109FN(S2NZ).

Ill. 2, 2A – Drawing of condenser of model HS-109FN(SNZ).

Ill. 2B – Drawing of condenser of models HS-52FN(SNZ) and HS-52FN(S2NZ).

Ill. 3 – Drawing of evaporator of model HS-109FN(SNZ).

Ill. 3A – Drawing of evaporator of model HS-129CN(NZ)/HS-129CN(SNZ).

Ill. 3B – Drawing of evaporator of models HS-52FN(SNZ) and HS-52FN(S2NZ).

Ill. 4 - IEC 60079-15 (for Group II A gases or the flammable refrigerant)
Certificate of compressor overload protector model DRB Series.

Ill. 5, 5A - IEC 60079-15 (for Group II A gases or the flammable refrigerant)
Certificate of thermostats.

Ill. 5A - IEC 60079-15 (for Group II A gases or the flammable refrigerant)
Certificate of thermostat model WP and WPF series.

Ill. 6 – Drawing of control panel for model HS-129CN(NZ)/HS-129CN(SNZ).

Ill. 7, 7A – Drawing of alternate control panel for model HS-129CN(NZ)/HS­129CN(SNZ).

Ill. 8 – Drawing of shelves for model HS-129CN(NZ)/HS-129CN(SNZ).

Ill. 9, 9A & 10 – Drawing of Machine Compartment Cover.

Ill. 11 - IEC 60079-15 (for Group II A gases or the flammable refrigerant)
Certificate of lampholder.