Metro SAQHD25BP-1 Installation Manual

®

SEISMIC FLOOR PLATES

SASES25BP-1 SASES50BP-1

INSTALLATION

INSTRUCTIONS

SASES25BP-2 SASES50BP-2

SASES25BP-4 SASES50BP-4

SAQHD25BP-1 SAQHD50BP-1

SAQHD25BP-2 SAQHD50BP-2

Wire Shelving Systems

Super Adjustable
2™ Super Erecta
Shelving

Original Super

®

Erecta® Shelving

Super Erecta
qwikSLOT
Shelving

™

®

SAQHD25BP-4 SAQHD50BP-4

®

MetroMaxQ® Shelving HD Super™ Shelving

InterMetro Industries Corporation

North Washington Street, Wilkes-Barre, PA 18705

For Product Information Call: 1-800-433-2232
Visit Our Web Site: www.metro.com

L01-418

Information and specifications are subject to change

without notice. Please confirm at time of order.

9/05

®

SEISMIC FLOOR PLATES

LIST OF
COMPONENTS:

(Floor Anchors not included)

INSTALLATION
INSTRUCTIONS

For Seismic Floor Plates

Part Number: Consists of:

SASES25BP-1 (4) floor plates (1) hardware bag (1) label bag
SASES50BP-1 (4) floor plates (1) hardware bag (1) label bag
SASES25BP-2 (2) floor plates (1) hardware bag (1) label bag
SASES50BP-2 (2) floor plates (1) hardware bag (1) label bag
SASES25BP-4 (1) floor plate (1) hardware bag (1) label bag
SASES50BP-4 (1) floor plate (1) hardware bag (1) label bag
SAQHD25BP-1 (4) floor plates (1) hardware bag (1) label bag
SAQHD50BP-1 (4) floor plates (1) hardware bag (1) label bag
SAQHD25BP-2 (2) floor plates (1) hardware bag (1) label bag
SAQHD50BP-2 (2) floor plates (1) hardware bag (1) label bag
SAQHD25BP-4 (1) floor plate (1) hardware bag (1) label bag
SAQHD50BP-4 (1) floor plate (1) hardware bag (1) label bag

FLOOR PLATE ASSEMBLY TO
SHELVING POST CONNECTION

The floor plate anchor assembly is
designed to allow in-field leveling of
the shelving and secure anchorage of
the shelving to the floor plates. This is
accomplished with standard shelves

and posts with leveling bolts.

1. Place the assembled shelving unit
in its intended location.

2. Mark on the floor the location of the
shelving posts, or place the floor
plates under the posts. Move the
shelving unit out of the way.

3. Utilizing a template, or the actual
floor plate, mark the location of the
floor anchors, drill appropriate holes,
and install the floor plates.

4. Move the shelving unit adjacent to
the floor plates and level the unit. Lift
the shelving unit and place the posts
into the pipe sleeves in the floor
plate assembly.

5. Once the shelving unit is in place
and level, horizontal holes in each
pipe sleeve are used to align a 13/32"
drill bit and a horizontal hole (or two,
as determined from the Seismic
Specifying Guide (L04-160)) is drilled
through the post. Alternatively, the
pipe sleeve holes can be used to
mark the post hole locations, the
shelving unit removed and the holes
in the post drilled.

6. Install a 3/8" diameter clevis pin (or
two) from the supplied hardware bag
through the floor plate pipe sleeve and
post, install a hitch pin clip.

7. Finally, affix the proper label
designating the unit as either 30 psf or
50 psf per shelf. The load rating is
determined by the tables in the
Seismic Specifying Guide and may be
shown on the installation drawing
provided with the quote package in
the planning stage of this project.

Notes: The lowest shelf should be as
close as possible to the floor plate, no
higher than 12" from floor.

If cleaning is an issue, it is
recommended a donut bumper be
specified to cover any spaces
between the post and the floor plate
anchor pipe. These may have been
specified in the quoting process and
provided — if not, order the donut
bumper to match the post type.

Metro does not provide the concrete
floor anchors. The correct floor
anchors must be used for the specific
installation conditions and meet all
applicable codes.