Metabo Invert 130-40, Invert 130-60 User Manual

Bedienungsanleitung

Operating Instructions

Instructions de service

Gebruiksaanwijzing

Instrucciones de uso

Invert 130/40
Invert 130/60

Achtung! Lesen Sie diese Anleitung vor der Installation und Inbetriebnahme aufmerksam durch.
Attention! Carefully read through these instructions prior to installation and commissioning.
Attention! Prière de lire attentivement la présente notice avant l'installation et la mise en service.
Attentie! Lees deze instructies voor de installatie en ingebruikname aandachtig door.

115 162 4029 / 0803 - 3.2

¡Atención! Lea con detenimiento estas instrucciones antes de la instalación y de la puesta en servicio.

Table of Contents

1 Technical Specifications
2 Scope of Application

2.1 Information
3 Commissioning
4 Description
5 Operation
6 TIG-Welding (optional)

6.1 Tips for TIG-Welding
7 Overloads
8 Trouble Shooting
9 Safety Information

9.1 Protection against Electrical Accidents
10 Wiring Diagram

1 Technical Specifications

Invert 130/40 Invert 130/60

Mains voltage: 1 ~ 230/240 V 1 ~ 230/240 V
Mains frequency: 50 - 60 Hz 50 - 60 Hz
Setting range: 100 V 100 V
Stromeinstellbereich: 5 - 130 A 5 - 130 A
Power input: manual arc 4.5 kVA 4.85 kVA

TIG 3.1 kVA 3.1 kVA

Operating voltage: manual arc 20,2 - 25,2 V 20.2 - 25.2 V

TIG 10,2 - 15,2 V 10.2 - 15.2 V
Max. current draw: 27 A 27 A
Mains fuse: 16 A time-lag 16 A time-lag
Duty cycle at max. manual arc 130 A / 50 % / 35 % 130 A / 80 % / 55 %
ouput (25 °C/ 40 °C): TIG 130 A / 40 % / 30 % 130 A / 60 % / 40 %
Operating modes: manual arc/TIG manual arc/TIG
Setting: stepless stepless
Suitable electrodes manual arc from 1.5 mm Ø from 1.5 mm Ø

TIG for steel 0.3 mm and up for steel 0.3 mm and up
Protection class: IP 23 S IP 23 S
Cooling: F F
Insulation class: F F
Temperature range: operation -10 °C - +40 °C -10 °C - +40 °C
Dimensions ( l x w x h): 255 x 110 x 210 mm 235 x 110 x 220 mm
Weight: 4.9 kg 4.9 kg
Operating conditions: relative humidity 10-80 % relative humidity 10-80 %

ENG

2 Scope of Application

The inverter welding machines are designed as a compact, easy to operate and field-safe unit. With it all metals
(except aluminium) can be welded. Special consideration has been given to stick electrode welding capabilities,
i.e. vertical-down welding. Due to its wide range of welding current setting the Invert 130 is very versatile, e.g. for
sheet metal and steel welding. In addition there is the capability of TIG welding with scratch start. With this welding
process steel, stainless steel and NF-metals (except aluminium) can be welded, e.g. thin plate welding or car body
work.

Product Liability/Warranty

This product shall only be used as specified. Any other use requires the written consent of
Metabo GmbH, Business Unit Elektra Beckum, P.O.Box 1352, D-49703 Meppen, Germany.
Please contact your dealer for any warranty claims.
Warranty work will essentially be carried out by service centres authorised by us. Repairs beyond the warranty
period may be carried out only by our authorised service centres.

Please preserve all repair invoices!

We reserve the right to make technical changes!

2.1 Information - Shown On Type Plate

The following explanations refer to the numbered boxes shown in Figure 2.3 according to ISO/IEC 60974-1.

a) Identification

Box l Name and address of the manufacturer or distributor or importer and, optionally, a trade mark and the

country of origin, if required
Box 2 Type (identification) as given by the manufacturer
Box 3 Traceability of design and manufacturing data, e.g. serial number
Box 4 Welding power source symbol (optional) e g

Single-phase transformer
Single- or three-phase transformer-rectifier
Single- or three-phase static frequency

converter-transformer-rectifier
Three-phase motor-generator
Three-phase motor-generator-rectifier

Three-phase rotating frequency Converter
Single-phase combined a.c. and d.c. power source

Engine-a.c. generator
Engine-generator-rectifier

Box 5 Reference to this Standard confirming that the welding power source complies with its requirements

b) Welding Output

Box 6 Welding process Symbol e.g.:

Manual metal arc welding with covered electrodes
Tungsten inert-gas welding

Metal inert and active gas welding including the use of flux cored wire

Selfshielded flux cored arc welding
Submerged arc welding
Symbol for plasma cutting
Symbol for plasma gouging

Box 7 Symbol for welding power sources which are suitable for supplying power to welding operations

carried out in an environment with increased hazard of electric shock (if applicable).

Box 8 Welding current symbol e.g.:

Direct current
Alternating current, and additionally the rated frequency in

hertz e.g.: ~50 Hz

Box 9 U0... V Rated no-load voltage

a) Arithmetic mean value in case of direct current
b) RMS value in case of alternating current
c) Ur... V Reduced rated no-load voltage in case of a voltage reducing device
d) Us... V Switched rated no-load voltage in case of an a.c. to d.c. switching device

Box 10 ... A/... V to... A/... V Range of output, rated minimum and maximum welding current and their

corresponding conventional load voltage.
Box 11 X Duty cycle (duty factor) symbol.
Box 12 I2 Rated welding current symbol.
Box 13 U2 Conventional load voltage symbol.
Boxes 11a, 11b, 11c ...% Values of the duty cycle (duty factor).

12a, 12b, 12c ... A Values of the rated welding current.

13a, 13b, 13c ... V Values of the conventional load voltage.
These boxes form a table with corresponding values of the three settings:
a) ... % duty cycle (duty factor) at the rated maximum welding current;
b) 60 % duty cycle (duty factor);

and

c) 100 % duty cycle (duty factor) as far as relevant.

Column a) need not be used if the duty cycle (duty factor) for the rated maximum welding

current is 60 % or 100 %.

Column b) need not be used if the duty cycle (duty factor) at the rated maximum welding current is 100 %.

c) Energy input

Box 14 Energy input symbol e.g.:

Input supply, number of phases (e.g. l or 3), symbol for
alternating current
and the rated frequency (e.g. 50 Hz or 60 Hz)

Engine
Motor
Belt drive

Box 22 IP.. Degree of protection, e.g. IP21 or IP23.
Box 23 Symbol for protection class II, if applicable.

3 Commissioning

Caution:

This product is assembled with great care and thoroughly checked. All units undergo a computerised check before
leaving the factory. Please check your machine for transport damage after unpacking. In case such damage is
detected please notify your supplier immediately.
Ensure that mains voltage matches the machine's rated voltage as shown on its name plate. Connect to 230/240V
AC circuit. The supply circuit need to be protected by a 16 amp time-lag fuse. Operation of other electrical equipment
on the same circuit while welding is limited.
Pure argon (of at least 99.998 % purity) is preferably used for TIG welding. Connection of the TIG torch to the gas
cylinder must be by means of a suitable pressure reducing device (max. 10 bar). The earth cable must have a
minimum lead cross section of 16 mm2. After setting the main switch [1] to ON the machine is ready to operate.

4Description

Controls

1
4

2
3

5
6

Figure 1: Front panel

Figure 2: Rear view

1 Mains ON/OFF switch
2 Welding current setting 5 - 130 A; with integrated automatic hot start
3 Neon control light; indicates thermal overloads or short circuits
4 ON/OFF control light
5 Socket for positive (+) pole; electrode holder, TIG: earth cable
6 Socket for negative (-) pole; earth cable, TIG: torch
7 Power cable
8 Cooling fan

7

8

5 Operation

The welding machines Invert 130/40 and 130/60 are primary clocked inverters, suitable for manual arc welding with
coated stick electrodes and for direct current TIG welding (optional).
The electrode diameter and the required welding current are selected according to the material to be welded.

Dust, dirt and metal chips will harm any welding machine. It is of particular importance that the air ventilation for
cooling is not disabled.

Prior to welding the joints must be cleaned and dirt, rust, grease and paint removed. Also slag from previous welds
must be completely removed.

Attach earth clamp firmly to work piece, assuring good metal to metal contact. Check that all cables and connectors
are in proper operating condition to ensure proper current conduction.
Place the uncoated end of the electrode into a notch of the electrode holder. With the welding machine a welding
accessory kit, consisting of welding visor and pick hammer, can be purchased. The tinted glass of the welding visor
protects the eye from harmful rays (ultraviolet and infrared rays). The clear glass plate protects the dark glass from
spatters and breakage. When removing slag it is strongly recommended to wear eye protection to prevent injury
from sharp and hot slag particles. Depending on electrode type and eye sensitivity protective glasses are available
in different shades. Normally protective glasses of shade DIN 9 are used for electrodes from 1.5 mm to 4 mm Ø.

Select the correct welding current as shown below:

Current (A) Electrode Ø Material Thickness

25 - 50 1.0 - 2.0 mm 1.0 - 2.0 mm
50 - 100 2.0 - 2.5 mm 2.0 - 4.0 mm
100 - 140 2.5 - 3.25 mm 4.0 - 8.0 mm
140 - 220 3.25 - 5.0 mm 8.0 - 12.0 mm

In principle do not use too thick an electrode.
As a general rule calculate 40 amps welding current per 1 mm of electrode core wire diameter. Depending on
electrode type, material thickness and weld position this calculated value may have to be adjusted plus or minus.
The Invert 130/40 and 130/60 works perfectly with thin plate, which is the outstanding feature of this machine, aside
from its extreme compact and robust design. It is characteristic of an inverter to generate a true direct current, which
makes for a soft and smooth running arc with reduced spatter formation.

Overview Of Stick Electrodes And Their Correct Use

In order to achieve a good weld the electrode has to be dry, so storing in a dry place is essential. Should electrodes
have become moist, dry in an oven at 200°C to 300°C for 1 - 2 hours.
Basic-coated electrodes always require pre-drying at 200°C to 300°C for 3 hours, unless they are vacuum-packed.
Stick electrodes are coded according to EN 499 and other standards, such as B.S. 639, AWS-SFA 5.1 and ISO

2560. The codes are always shown on the electrode package. The electrode description is defined by the
manufacturer according to the standards, the description is checked by an independent test institute for
compliance. This information is shown on the packaging.

Welding Hints

(Figure 6)

(Figure 5)

(Figure 7)

Because of the multitude of and great differences in the important points for welding only the very basic operations for
the most common electrodes for low-carbon steels, the rutile or rutile cellulose electrode, are introduced here. In the
case that other electrodes have to be used, the electrode manufacturers supply upon request all relevant information
for the type of special electrode to be used.
Always make some trial welds on scrap material. Select electrode diameter and welding current as per Table 1. Attach
earth clamp to work piece and place electrode into electrode holder as described earlier. Now hold the electrode tip
approx. 2 cm above the starting point of your weld seam. Hold the welding visor in front of your face and draw the
electrode with a short stroke along the groove. Through the welding shield you watch the arc, keeping it to a length of
1 to 1.5 times the electrode diameter.

wrong

arc too long

(Figure 3)

correct

approx. 1 - 1.5 the electrode-Ø

(Figure 4)

The correct arc length is important for a good weld, because with too short or too long an arc both welding current and
working voltage change. A low working voltage causes insufficient penetration. Too high or too low welding current gives
a poor welding seam. Too long an arc does not sufficiently melt the parent material, resulting in high spatter losses. Also
the air, with its detrimental substances like hydrogen and nitrogen, may get access to the weld pool.
For a good weld the work angle of the electrode (or electrode inclination angle) is of substantial importance. The
inclination should be 70° - 80° to the welding direction. With the work angle too steep slag will run under the weld pool,
too flat an work angle causes the arc to spatter, in both cases the result is a porous, weak welding seam (see figure
5 - 7).

wrong
welding direction

> 80°

wrong correct
welding direction

welding direction

< 70°

70-80°

The welder has to keep the arc at the same length, that is the electrode burn-off is compensated by feeding the electrode
into the weld. At the same time the welder has to watch the weld pool for even penetration and width.
Welding is always done from left to right (backhand welding).
At the end of the welding seam the electrode can not simply be lifted or pulled from the weld, this creates porous end
craters, which weaken the weld. To correctly terminate a weld the electrode is held for a short moment at the end of the
weld seam, then lifted in an arc over the just laid weld.

wrong

(Figure 8)

correct

(Figure 9)

Remove slag only after it has cooled down and is no longer glowing.
If an interrupted weld is to be continued, the slag at the end of the already finished weld must be removed. Then the
arc can be started either in the groove or on the weld, as described earlier, and then moved to the end of the weld, which
has to be thoroughly melted for good fusion. Welding is then continued normally.

6 TIG Welding (optional)

Due to the same welding characteristics as with manual arc welding, TIG welding is possible with models Invert
130/40 and 130/60.
For TIG welding a TIG torch model SR 17 V (see section 11) is used, which is always connected to the negative
(-) pole. The arc is started by scratching with the tungsten electrode on the workpiece (causing a short-circuit).
The shielding gas is supplied directly from the pressure reducing device of the gas cylinder to the torch. A gas flow
rate of 6-7 l/min is recommended. Pure argon is required as shielding gas.
The earth lead is connected to socket [4]. The welding current is selected with the potentiometer [2], then the arc
is ignited by a brief contact of the tungsten electrode with the workpiece (scratch start).

6.1 Practical Hints for Operation

To ensure good arc starting and good welding results the following should be adhered to:

Electrode types

1

Only thoriated electrodes are recommended for use, e.g.
WT 20 1.8 - 2.2 % thorium oxide, colour code: red or grey

2

Electrode diameter
The electrode diameter must correspond to the welding current.
Rule of thumb: less than 80 A Ø 1.0 mm

70 to 140 A Ø 1.6 mm

3

Tungsten electrodes have to be ground in longitudinal direction. Use a fine grit grinding wheel and grind from
tip to shaft.

Too much gas flow can reduced the arc starting ability (arc extinguished by blowing).

4

7 Overloads

The inverter welding machines are positively protected against overloads by several independent protection
devices. If the permissible duty cycle is exceeded, the machine is shut down automatically. This is indicated by
the control light [3]. After a short cooldown period the machine is operational again.
Important: Do not switch the machine off during the cooldown period, as this will cut the power to the fan,
considerably extending the cooldown period.

8 Trouble Shooting

When welding the control light [3] comes on and the
welding current goes off.

It is difficult to keep the arc burning.

Machine switched on but no welding current.

Thermal overload protection has engaged. Let machine
run idle for several minutes to let cool down.

If the electrode is not moist, damaged or has been stored
too long, there may be a voltage drop (less than 190 V at
full load), probably caused by too long and extension
cord.

- check mains fuse

- voltage too high (over 250 V), which triggers the
corresponding protection device

Poor arc starting with TIG welding

Porous welding seam

- insufficient or no gas supply

- tungsten electrode wrongly ground

- wrong electrode diameter

- workpiece surface not clean (oil, grease)

- wrong setting of shielding gas flow rate (too much or
too little)

- wrong shielding gas (pure argon only)

- impurities in shielding gas

- wrong position of TIG torch

9 Safety Precautions/Accident Prevention

- This Welding Machine should only be used for its intended application (TIG and manual arc welding).

- Operate machine only on power supply circuits having a fully operational protective bonding circuit (earth/ground
lead).

- Know and adhere to all applicable local safety standards and codes.

9.1 Protection against the Risk of Electric Shock

The earth cable is to be firmly attached to the workpiece, ensuring good conduction. Protect welding cables and
the power cable from damage. Replace damaged cables with genuine Elektra Beckum replacement parts. Place
torch or electrode holder on insulated backing during short work breaks. For longer work breaks switch machine
off. Wear dry and insulating gloves and shoes when welding. Always disconnect machine from power by pulling
the power cable's plug from the outlet before servicing.

Protection against UV Rays, Burns and Fumes:

- Wear suitable protective clothing to prevent burns (sleeved gloves, welding apron etc.).

- Always use a welding visor.

- Screen off workplace to protect other persons working nearby against UV rays.

- Welding materials with contaminated surfaces may generate toxic fumes. Ensure surface is clean before welding.

- Zinc-plated or galvanized material should not be welded as zinc fumes are highly toxic.

- When welding under an increased electrical hazard it is important to wear undamaged, dry and insulating clothing.

Fire Prevention

- Hot slag or sparks can cause fire when getting in contact with combustible solids, liquids and gases.

- Remove all combustible and inflammable material from the work area.

- Fuel, lubricant and solvent containers must not be welded, even when they are empty. The same applies to hollow
spaces containing or having contained combustible materials.

10 Wiring Diagram Invert 130/40 and 130/60

(5)

(6)

(4)

(2)

(3)

(7)

(1)

11 Exploded View Drawing and Spare Parts List TIG-Torch SR 17 V

1

2

3
4
5
6

7
8

9
10
11
12
13

Ø 1,0
Ø 1,6

Ø 1,0

Ø 1,6
(5) Ø 8,0
(6) Ø 9,5

(1) Power cable
(2) Switch/plug
(3) Control PCB
(4) Transformer
(5) Diodes
(6) Choke
(7) Fan

1 132 712 7230
2 132 712 7248
3 132 712 7892
4 132 712 7078
5 132 712 7086
6 132 766 9202
7 132 766 9199
8 132 712 7256
9 132 717 1174

1514 16

10 132 712 7132
11 132 712 7140
12 132 712 7876
13 132 712 7175
14 132 766 9148
15 132 766 9180
16 821 503 7887

D DEUTSCH ENG ENGLISH

S

L

Ê

A

ÖRSÄ

E

K

A

KONFORMITÄTSERKLÄRUNG DECLARATION OF CONFORMITY
Wir erklären in alleiniger Verantwortlichkeit, dass dieses Produkt mit den

folgenden Normen übereinstimmt* gemäß den Bestimmungen der
Richtlinien**.

F FRANÇAIS NL NEDERLAND
DECLARATION DE CONFORMITE CONFORMITEITSVERKLARING

Nous déclarons, sous notre seule responsabilité, que ce produit est en
conformité avec les normes ou documents normatifs suivants* en vertu
des dispositions des directives **

IT ITALIANO ES ESPAÑO
DICHIARAZIONE DI CONFORMITÀ DECLARACION DE CONFORMIDAD

Noi dichiariamo sotto la nostra esclusiva responsabilità che il presente
prodotto è conforme alle seguenti norme*. in conformità con le
disposizioni delle normative **

We herewith declare in our sole responsibility that this product complies
with the following standards*
in accordance with the regulations of the undermentioned Directives**

Wij verklaren als enige verantwoordelijke, dat dit product in
overeenstemming is met de volgende normen*
conform de bepalingen van de richtlijnen**

Declaramos bajo nuestra exclusiva responsabilidad, que el presente
producto cumple con las siguientes normas*.de acuerdo a lo dispuesto
en las directrices**

PT PORTUGU
DECLARAÇÃO DE CONFORMIDADE

Declaramos sob nossa responsabilidade que este produto está de
acordo com as seguintes normas*.de acordo com as directrizes dos
regulamentos **

FIN SUOMI NO NORGE
VAATIMUKSENMUKAISUUSVAKUUTUS SAMSVARSERKLÆRING

Vakuutamme, että tämä tuote vastaa seuraavia normeja*.on direktiivien
määräysten mukainen**

DA DANS
OVERENSSTEMMELSESATTEST OŚWIADCZENIE O ZGODNOŚCI

Hermed erklærer vi på eget ansvar, at dette produkt stemmer overens
ed følgende standarder*. iht. bestemmelserne i direktiverne**

EL ΕΛΛHNIK
∆ΗΛΩΣΗ ΑΝΤΙΣΤΟΙΧΕΙΑΣ MEGEGYEZŐSÉGI NYILATKOZAT

∆ηλώνουµε µε ιδία ευθύνη ότι το προϊόν αυτό αντιστοιχεί στις
ακόλουθες προδιαγραφές*
σύµφωνα µε τις διατάξεις των οδηγιών**

S SV SVENSK

KRAN OM ÖVERENSSTÄMMELS

F
Vi försäkrar på eget ansvar att denna produkt överensstämmer med

följande standarder*. Enligt bestämmelserna i direktiven**

Vi erklærer under eget ansvar at dette produkt samsvarer med følgende
normer*. henhold til bestemmelsene i direktiv**

POL POLSKI

Oświadczamy z pełną odpowiedzialnością, że niniejszy produkt
odpowiada wymogom następujących norm*.według ustaleń wytycznych
**

HU MAGYAR

Kizárólagos felelősségünk tudatában ezennel igazoljuk, hogy ez a
termék kielégíti az alábbi szabványokban lefektetett
követelményeket*.megfelel az alábbi irányelvek előírásainak**

INVERT 130/40

* EN 60974-1, EN 50199

** 89/ 336/ EWG, 72/ 23/ EWG, 93/68/ EWG

Jürgen Kusserow

Vorstand

ELEKTRA BECKUM AG – Daimlerstraße 1 – 49716 Meppen

Meppen, 27.02.2001 1001016

Apartado 53; 7000-171 Evora Codex; (+351) 266 - 74 93 00; (+351) 266 - 74 93 09;

[e-mail]

Portugal; BOLAS-Maq. e Ferramentas de Qualidade, S.A.; Rua B, Lotes 8-10-12;

Puerto Rico; J.J. Trading; PMB 409 P.O. Box 4956 Caguas; ; Puerto Rico 00726-4956;

AJAC

(+1) 787 - 739 9693; (+1) 787 - 739 1177; [e-mail]

[e-mail]

Zona 9-A; Panamá; ([phone]; ([phone]; [e-mail]

STREET; MEADOWDALE - Germiston; Johannesburg; (+27) 11 - 372 - 96 00;

(+27) 11 - 453-41 63; [e-mail]

Domingo; (+1) 809 - 531 50 80; (+1) 809 - 531 53 38;

[e-mail]

(+40) 1 - 3 46 31 31; (+40) 1 - 3 46 31 51; [e-mail]

(+7) 095 - 198 43 14/198 17 13; (+7) 095 - 198 43 14; [e-mail]

(+41 ) 52 - 3 54 34 44; (+41) 52 - 3 54 34 45; [e-mail]

(+22) 1 - 823.67.14; (+22) 1 - 823.67.14;

Number One Building; Singapore 408563; ([phone]; ([phone];

[e-mail]

(+421) 33 - 641 2522; (+421) 704 - 6 41 25 22; [e-mail]

(+386) 61 - 1 68 16 16; [e-mail]

263-1 Ipchung-Dong, Chung-Gu; Seoul; (+82) 2 - 22 76 09 14/5; (+82) 2 - 2 78 62 62;

[e-mail]

P.O. Box 214 / 130 Front Street; Colombo 11; (+94) 1 - 2 81 71 / 72 / 73;

(+94) 1 - 50 11 83; [e-mail]

Santa Lucia; (+1)758 - 452-99 14; (+1)758 - 452-99 15; [e-mail]

P.O. Box 169 / Code 113; ; Muscat; ([phone]; ([phone];

[e-mail]

(+46) 36 - 16 07 54; [e-mail]

(+963) 21 - 2 11 62 45; [e-mail]

(+886) 2 - 28 11 08 08; (+886) 2 - 28 16 98 38; [e-mail]

Pomprab Bangkok 10100; (+66) 2 - 3 28 11 89; (+66) 2 - 3 28 13 04; [e-mail]

(+216) 1 - 25 83 92; (+216) 1 - 35 18 45; [e-mail]

(+90) 212 - 2 56 49 50; (+90) 212 - 2 38 98 26; [e-mail]

03 151 Kiev; (+380) 44 - 2 45 94 34; (+380) 44 - 2 45 96 57; [e-mail]

(+971) 6 - 533 05 51 ; (+971) 6 - 533 73 68; [e-mail]

Brandywine Industrial Park; West Chester, PA 19380; (+1) 610 - 4 36 59 00;

(+1) 610 - 4 36 90 72; [e-mail]

(+598) 2 - 92 26 06; (+598) 2 - 92 12 69; [e-mail]

Caracas 1071; (+58) 212 - 2 37 30 22; (+58) 212 - 2 39 23 65;

[e-mail]

Tan Binh District; Ho Chi Minh City; (+84) 8 - 811 74 54; (+84) 8 - 811 63 38;

[e-mail]

([phone]; ([phone]; [e-mail]

Qatar; Gulf Incon; P.O.Box 4076; ; Doha; ([phone]; ([phone];

Rep. de Panamá; German-Tec (Panamá) S.A.; Via Argentina 46-70; Apartado 342,

Republic of South Africa; Metabo Power Tools SA (Pty.) Ltd.; 165 Van DER BIJL

Republica Dominicana; Agroindustrial Ferretera S.A.; Av. Luperon No. 42; ; Santo

Rumania; S.C. Agent Trade S.R.L.; Splaiul Unirii 235-237; ; 74299 Bucuresti 3;

Russia; OOO ITA-Strojinkom; Uliza Alabjana 3; ; 125057 Moskau;

Schweiz; Metabo (Schweiz) AG; Lindauerstr. 17; ; 8317 Tagelswangen;

Senegal; Ets. M.Y.S.; 12, Rue Tolbiac; B. P. 2389; Dakar;

Singapore; HOMELY HARDWARE PTE LTD; No. 1 Ubi Crescent #01-01;

Slovakia; STAMET Bratislava spol. s.r.o.; M.R. Stefanika 28; ; 90201 Pezinok;

Slovenia; Dilex d.o.o.; Ogrinceva 17; ; 1000 Ljubljana; (+386) 61 - 1 68 16 20;

South Corea; Metabo-Korea Co. Ltd.; Room No. 101, Daesung Building;

Sri Lanka; Hunter + Company Ltd.; General Hardware Importers ;

St. Lucia; Eurotools Int`l Ltd; P.O.Box RB 2484; Rodney Bay, Gros Islet, West Indies;

Sultanate of Oman; Suhail & Saud Bahwan Building Materials L.L.C.;

Sverige; Metabo Sverige AB; Skiffervägen 6; ; 553 03 Jönköping; (+46) 36 - 10 06 60;

Syria; Bachar & Elias Taoutel; Boite Postal 325; ; Aleppo; (+963) 21 - 2 11 80 30;

Taiwan; Taiwan Overseas Trade Co. Ltd.; No. 103 Chung King N. Road Sec. 4; ; Taipei;

Thailand; SSM - Sri Siam Mongkol Co., Ltd; 1570-1576 Krung Kasem RD.; ;

Tunesia; L´Equipment Moderne; 86, Ave. de Carthage; ; 1000 Tunis;

Turkey; Burla A.S.; Voyvoda Cad. 61-65; ; 80003 Karaköy-Istanbul;

Ukraine; Comservice; Ukraian-Russian Joint Venture 2; Narodnogo Opolcheniaya;

United Arab Emirates; Sedana Trading Co; P.O. Box 1919; ; Sharjah;

United States of America; Metabo Corporation; 1231 Wilson Drive / P.O.Box 2287;

Uruguay; Goldfarb S. A.; Rio Negro 1617; P.O. Box 11100; Montevideo;

Venezuela; OLY-COPIA C.A.; 3 ra Transversal Los Ruices ; Edificio Principal II, Piso 4;

Vietnam; HUU HONG MACHINERY CO., LTD.; 157-159 Xuan Hong Street, Ward 12;

(+263) 4 - 77 52 56-9; (+263) 4 - 77 06 95; [e-mail]

Yugoslavia; WHM WOBY HAUS MARKT; Brace Ribnikara 55; ; 21000 Novi Sad;

Zimbabwe; Field Technical Sales; 45 Kelvin Road North; Graniteside; Harare;

Ambethan Road, Kharabwadi; Chakan, Tal.: Khed, Dist.-Pune(Pin410 501);

India; Metabo Power Tools PVT Ltd.; Plot No. 40, WMDC Industrial Complex;

Country; Company; Address 1; Address 2; City; Phone; Fax; E-mail

Albania; Extra Industrial Goods; Rl. Fadil Rada 88; ; Tirana; (+355) 42 - 3 30 62;

(+91) 213 - 55 22 03; (+91) 213 - 55 21 61

Indonesia; P.T. Kawan Lama Sejahtera pt; Gedung Kawan Lama Jl. Puri Kencana No. 1;

(+355) 42 - 3 30 62; [e-mail]

Algerie; Haddad Equipement Professionel; 98 A, Site du Lycée; ; 16012 Rouiba;

Meruya - Kembangan; Jakarta 11610; (+62) 21 - 5 82 82 82;

(+213) 21 - 85 49 05; (+213) 21 - 85 57 72; [e-mail]

(+62) 21 - 5 82 55 88; [e-mail]

Argentina; Metabo Argentia S.A.; Teniente Gral. Richieri 4773; ; 1702 - Ciudadela -

Iran; Kalavaran Co. Ltd.; P.O.Box: 11365 - 4653; ; Tehran;

Buenos Aires; (+54) 11 - 44 88 - 9180; (+54) 11 - 44 88 - 39 89; [e-mail]

(+98)21 - 67 00 862/67 01 383; (+98)21 - 67 09 427; [e-mail]

Australia; Metabo Pty. Ltd; 10 Dalmore Drive; ; Scoresby, Melbourne, Vic. 3179;

Israel; Proter + Cohn Ltd; Technical Supply P.O.Box 33215 / 3; Haatzmaut Road;

(+61) 3 - 97 65 01 99; (+61) 3 - 97 65 01 89; [e-mail]

33033 Haifa; (+972) 4 - 8 64 04 69; (+972) 4 - 8 67 18 03; [e-mail]

Italia; Carlo Stechel & Figli S.rl; Via Buozzi, 22; ; 20 097 San Donato Milanese (MI);

P.O. Box 5262; Manama; ([phone] / 71 41 74; ([phone];

Bahrain; Bokhammas Establishment; Bldg. 334 Block 321 Old Exhibition Road;

(+39) 02 - 52 77 71; (+39) 02 - 55 60 03 22; [e-mail]

Japan; Metabo Japan Co., Ltd.; 5-1024-3, Baigou, Ohme-city; ; Tokyo 198-0063;

[e-mail]

Bangladesh; East Bengal Impex; 175, Nawabpur Road (4th floor); ; Dhaka; ;

(+81) 4 - 28 77 05 06; (+81) 4 - 28 77 05 07

Jordan; Newport Trading Agency; P.O.Box 6166 / 151 Hashimi Str.; City Center;

(+880) 2 - 9 56 94 77 / 9 55 04 00;

Belarus; Rosinstrument LTD. INTL. DEPT.; PR-T Skkoriny 107-11; P.O.Box 67; 220023

Amman 111 18; (+962) 6 - 465 56 80; (+962) 6 - 464 54 39; [e-mail]

Minsk; ([phone]; ([phone]; [e-mail]

Kenya; Agriquip Agencies (E.A.) Ltd.; Lusaka Rd.; P.O.Box 30 612; Nairobi;

Belgique; Metabo Belgium; ´t Hofveld 3 - 5; ; 1702 Groot Bijgaarden;

(+254) 2 - 54 02 70 / - 73; (+254) 2 - 54 00 56; [e-mail]

Kingdom of Saudi Arabia; Saudi Industrial Tools Corporation; Madinah Road, Kilo 9;

(+32) 2 - 4 67 32 10; (+32) 2 - 4 66 75 28; [e-mail]

Bolivia; Agencias Generales S.A.; Casilla de Correo 530 Avda. San Martin S-0253; ;

P.O.Box 11429; Jeddah 21453; (+96) 62 - 6 82 04 58; (+96) 62 - 6 91 12 67;

Cochabamba; (+591) 4 - 425 10 62 ; (+591) 4 - 425 10 61; [e-mail]

[e-mail]

Bosnia and Herzegovina; Agrarkombinat; Majevicka 1; ; Banja Luka;

Kuwait; Naser Moh. Al-Sayer ; Gen. Trading & Contracting Co.; P.O. Box 663 SAFAT;

(+387) 51 - 302 718; (+387) 51 - 785 708; [e-mail]

13007 State of Kuwait; ([phone]; ([phone];

Brazil; Metabo do Brasil Ltda.; Rua Guicurus 306 - Vila Conceicao; ;

[e-mail]

Diadema - Sao Paulo - Cep 09911-630; (+55) 11 - 40 51 - 25 11;

Latvia; SIA WESS Instrumenti un Tehnika Ltd.; Ganibu dambis 34 a; ; 1005, Riga;

(+55) 11 - 4056 - 4152; [e-mail]

([phone]; ([phone]; [e-mail]

Latvia; Stoller Sia; Krasta 42; ; 1003, Riga; ([phone];

(+359) 2 - 9 78 58 90; (+359) 2 - 9 78 86 04; [e-mail]

Bulgariia; KIROV Ltd.; Gara Iskar; Porutschik-Nedeltscho-Bontschev-Str.10; 1582 Sofia;

([phone]; [e-mail]

Lebanon; SPAN s.a.r.l.; Tools & Equipment Division; P.O. Box 90 - 1218; Beirut;

Ontario, L4Z 1 W6; (+1) 905 - 755 06 08; (+1) 905 - 755 06 11; [e-mail]

Canada; Metabo Canada Inc.; 190 Britannia Road East; Unit No. 12; Mississauga,

([phone]; (+961) 1 - 902 690; [e-mail]

Ceska Republica; Metabo s.r.o; Kralovicka 544; ; 250 01 Brandys nad Labem;

Lithuania; Technikonas; Savanoriu 286; ; 3042 Kaunas; (+370) 37 - 31 15 53;

(+420) 202 - 80 44 55; (+420) 202 - 80 44 56; [e-mail]

(+370) 37 - 31 10 21; [e-mail]

Macedonia; MAKWELD D.O.O.; Ilindenska 138; ; 1000 Skopje; (+389) 2 - 363 180;

(+56) 2 - 6 99 04 85; [e-mail]

Chile; Nordchil S.A.; San Diego 895; ; Santiago de Chile; (+56) 2 - 6 72 29 11;

(+389) 2 - 364 746; [e-mail]

Magyarorszag; INNOSERVICE-METABO Márkaszerviz Kft.; 1101 Bp. Köbányai út.

Bogota; (+57) 1 - 346 28 99; (+57) 1 - 346 29 16; [e-mail]

Colombia; EUROTOOLS Ltda.; Avenida Caracas No. 74-25; Edificio Ferricentros-4 Piso;

47./b.; ; 1475 Budapest; (+36) 12 - 60 67 12; (+36) 12 - 60 14 23;

Costa Rica; Capris S.A.; Frente la Imprenta Nacional, La Uruca; P.O. Box 7-2400;

[e-mail]

San José; ([phone]; ([phone]; [e-mail]

56100 Kuala Lumpur; (+60) 3 - 92002966 / 92003966; (+60) 3 - 92007599;

Malaysia; Finetools SDN BHD; No. 7 Jalan 1/92C; Batu 3 1/4 Jalan Cheras;

(+385) 1 - 24 06 000; [e-mail]

Croatia; CROM d.o.o.; Obrtnicka 2; ; 10000 Zagreb; (+385) 1 - 24 06 246;

[e-mail]

Malta; G + T Imports Limited; Metabo Shop, Birkirkara By-Pass; ; Iklin BZN 11;

1641 Lefkosia, Cyprus; (+357) 22 - 34 95 77; (+357) 22 - 34 93 94;

Cyprus; Med Marketing Ltd. (eurotools); P.O. Box 27017; 17, Digenis Akritas Ave;

(+356) 21 - 43 54 24; (+356) 21 - 41 73 58; [e-mail]

[e-mail]

([phone]; [e-mail]

Mauritanie; S.T.A.F; B.P.: 40246; ; Nouakchott; ([phone];

(+45) 43 - 31 34 01; [e-mail]

Danmark; Metabo Danmark A/S; Helgeshoj Allé 12; ; 2630 Tastrup; (+45) 43 - 31 34 00;

([phone]; [e-mail]

Mauritius; Dema - Supplies Ltd.; 2A Deschartres Street; ; Port Louis; ([phone];

0180 - 3 00 04 16; 0180 - 300 04 17; [e-mail]

Deutschland; Metabowerke GmbH ; Walter-Rauch-Str. 1; ; 72622 Nuertingen;

Mexico; Uniservicio Ferretero S.A de C.V.; Matamoros No. 237 Col. la Joya ;

Ecuador; Maquinarias Henriquez C.A.; P.O.Box 09 - 01 - 43 61; ; Guayaquil;

Del. Talpan; C.P. 14090 México, D.F.; (+52) 5 - 555 737 233; (+52) 5 - 555 737 244;

(+593) 4 - 25 43 00; (+593) 4 - 25 49 39; [e-mail]

[e-mail]

Moldova; BRISAR-COM S.R.L.; str. Sciusev, 78; ; 2012 Chisinau; (+373) 2 - 22 24 50;

([phone]; [e-mail]

Eestlane; A/S MECRO; Peterburi tee 44; ; 11415 Tallinn; ([phone];

(+373) 2 - 27 77 87; [e-mail]

Morocco; Sté Yyes Rouger; 20 Bd. Ibn Tachfine; ; 20300 Casablanca;

(Cairo); (+20) 2 - 3 03 02 51 / 3 47 89 17; (+20) 2 - 3 02 58 96;

Egypt; Modern Machines + Materials Co.; 18 Geziret El Arab. St.; ; Mohandseen Giza

([phone]; (+212) 2 - 31 24 62

El Salvador; Metabo S.A. de C.V.; Colonia Santa Clara, Pasaje C No. 20;

Nederland; Metabo Nederland b.v.; Postbus 180; ; 3620 AD Breukelen;

Cuscatancingo; San Salvador; (+503) 2 - 38 47 65; ([phone];

(+31) 3462 - 6 42 44; (+31) 3462 - 6 35 54; [e-mail]

[e-mail]

New Caledonia; Ets. Szemmelveisz; 3, Rue Fernand Forest; Boite Postale 668;

Espana; Herramientas Metabo S.A.; Polígono Ind. Prado del Espino; C/Forjadores, 12;

98845 Nouméa; ([phone]; ([phone]; [e-mail]

New Zealand; Tooline Ltd.; 49 A Sonter Road; P.O. Box 797; Christchurch;

28660 Boadilla del Monte (Madrid); (+34) 91 - 6 32 47 40; (+34) 91 - 6 32 41 47;

[e-mail]

(+64) 3 - 36 55 931; (+64) 3 - 36 55 932; [e-mail]

Nigeria; Mathani Brothers Ltd.; 60 Park View North Action; ; London W3 OPT;

([phone]; ([phone]; [e-mail]

Ethiopia; SUTCO Pvt. Ltd. Co.; W. 19 K. 50 HN new, Wollo Sefer; ; Addis Ababa;

(+44) 20 - 8992 5727; (+44) 20 - 8992 5335; [e-mail]

Finland; Wihuri Oy Autola; P.O. Box 58 Manttaalitie 9; ; 01511 Vantaa;

(+234) 1 - 774 1305; (+234) 1 - 774 1305; [e-mail]

Nigeria; Bestline Nigeria Ltd.; 15, Hospital Road; Olodi Apapa; Lagos ;

(+358) 9 - 41 58 15; (+358) 9 - 41 58 22 07; [e-mail]

France; Metabo S.A.; Z.A.C. 2, Avenue des Ormeaux; ; 78180 Montigny-le-Bretonneux;

Norway; Metabo Norge AS; Postboks 1296; ; 3205 Sandefjord; (+47) 33 - 44 55 55;

(+33) 1 - 30 64 55 30; (+33) 1 - 30 44 37 68; [e-mail]

(+47) 33 - 44 55 50; [e-mail]

Pakistan; Mercantile Company; Mercantile House 44-Brandreth Road; ; Lahore;

P.O. Box 1783; Accra; (+233) 21 - 66 39 94; (+233) 21 - 78 02 90;

Ghana; Emmnock Powercom Ltd.; Knutsford. Avenue opp. Morocco House;

(+92) 42 - 7 66 11 88/7 63 06 81; (+92) 42 - 7 66 45 89/7 63 45 95;

[e-mail]

(+595) 981 - 43 15 13; (+595) 21 - 33 36 77; [e-mail]

(+51) 14 - 4 22 86 31; (+51) 14 - 442 41 30; [e-mail]

(+63) 2 - 3 63 01 59; (+63) 2 - 3 61 48 41; [e-mail]

(+48) 91 - 5 78 11 95; (+48) 91 - 5 78 07 76; [e-mail]

Paraguai; Taguato S.A.; Avda.Gra.Santos No. 1948/Tte. Garay; ; Asuncion;

Peru; Sucesion Carlos Kaufmann; Juan de Arona 760, Of.102 ; ; San Isidro ;

Philippines; Mach Tools Inc.; 185 A & B del Monte Avenue; ; Manresa, Quezon City;

[e-mail]

Southampton / SO 16 OYT; (+44) 2380 - 73 20 00; (+44) 2380 - 74 75 00;

[e-mail]

01009; ([phone]; ([phone]; [e-mail]

Great Britain; Metabo (UK) Ltd.; 25 Majestic Road ; Nursling Industrial Estate;

Guatemala; Almacen la Palma S.A.; 2a Calle 4-38, Zona 9; ; Guatemala Ciudad,

Hellas; Fedon N. Economides + Co.; Prigiponison Street 27; ; 11363 Athens;

([phone]; [e-mail]

Polska; Metabo Polska Sp. z o.o.; Gdynska 28; ; 73-110 Stargard Szczecinski;

Polynésie francaise; Ets Dieumégard Import; BP 14 132 Arue; ; Tahiti; ([phone];

(+30) 1 - 8 21 60 83 / 8 84 29 66; (+30) 1 - 8 82 56 00; [e-mail]

Sha Wan Road; Kowloon / Hong Kong; ([phone]; ([phone];

[e-mail]

([phone]; [e-mail]

Hong Kong; Jebsen & Co. Ltd. ; 9/F, Jebsen Motor Group Building; 924-926 Cheung

Iceland; Fossberg Ltd; Sudurlandsbraut 14; ; 108 Reykjavik; ([phone];