Members Mark Sonoma Owner's Manual
Sonoma Hardtop Gazebo 10’ X 12’
Owner’s Manual
Congratulations on your purchase of our Sonoma Hardtop Gazebo. Our clear, easy to follow,
step-by-step instructions will guide you through the assembly process from start to finish.
WARNING:
THIS UNIT IS HEAVY! For safety, DO NOT assemble this item alone. Six to eight people are
recommended for safe assembly.
Keep all children and pets away from assembly area. Children and pets should be supervised
when they are in the assembly area of the gazebo.
Do not assemble less than 6 ft / 1.8 m from any obstruction such as a fence, garage, house,
overhanging branches, laundry line or electrical wires.
Some parts may contain sharp edges. Wear protective gloves.
When assembling and using this product, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment. Please read all instructions before
assembly and usage.
For outdoor use only. Install on level ground.
Check all bolts for tightness before and during usage.
IMPORTANT
Please take time to read these instructions thoroughly and follow each step carefully for safe and
easy operation. Keep this manual for future reference.
We would like to hear from you with any comments or suggestions. In the continental U.S., you can
call us toll-free at 1-888-301-0332 from 8 a.m. to 5 p.m. CST Monday – Friday. You can also send us
an email using the feedback icon at SamsClub.com.
Call centre for missing parts: 1-866-578-6569 from 8:00 a.m. EST to 8:00 p.m. PST.
Parts List
A1 (x2) Long Decorative Gutter B1 (x2) Short Decorative Gutter
C1(X2)
Corner Decorative Gutter
1
D1(x2) Corner Decorative Gutter 2
E1(x4) Middle Beam Connector F1(x8) Decorative Gutter Connector
G1(X4) Corner Connector H1(x4) Long Mosquito Netting Tube
I1(x4)
Short Mosquito Netting
Tube
Step 1
Step 2
A2(x4) Top Slanting Bar B2 (x1) Big Top Frame
C2 (x4)
Middle Beam of
Big Top
D2 (x2)
Left Long Support Beam of
Big Top Long Side
E2 (x2)
Right Long Support Beam
of Big Top Long Side
F2 (x2)
Left Short Support Beam of
Big Top Long Side
G2( x2)
Right Short Support
Beam of Big Top Long
Side
H2
(x2)
Left Long Support Beam of
Big Top Short Side
I2 (x2)
Right Long Support Beam
of Big Top Short Side
J2 (x2)
Left Short Support Beam of
Big Top Short Side
K2 (x2)
Right Short Support
Beam of Big Top Short
Side
Step 3
A3 (X2)
Small Top Bottom Beam
1
B3 (X4) Small Top Sheeting
C3 (x2)
Roof cover of small top
long side
D3 (x2)
Roof Cover of Small Top
Short Side
E3 (x1)
Small Top Bottom
Connecting Frame
F3 (X2) Small Top Bottom Beam 2
G3 ( x1)
Small Top Connector
H3 (x1) Small Top Cover
I3 (x1) Top Decor J3(x1) Chandelier Hook
Step 4
A4(X4) Post Base
B4 (x4) Base Cover
C4 (x4) Post
D4 (x4)
Top Block
E4(X4) Block Plate
F4(X2) Short Right Arc Support
G4(X2) Short Left Arc Support H4(X2) Long Right Arc Support
I
4(X2) Long Left Arc Support
Step 5
A5(x2)
Left Long Big Top
Cover
B5 (x2)
Right Long Big Top Cover
C5 (x4)
Left Middle Big Top
Cover
D5(x4)
Right Middle Big Top
Cover
E5 (x4)
Left Small Big Top
Cover
F5 (x4)
Right Small Big Top Cover
G5 (x2)
Short Big Top Cover
H5(X4)
Top Cover
I5(X18)
Roof Press Sheet
J5(x1)
Mosquito Netting
Hardware Pack 1
AA
Plastic Cap
16 PCS
BB
M6 Flat Washer
64 PCS
CC
M6x15 Short Bolt
64 PCS
JJ
Hook
52 PCS
LL
M6 Wrench
2PCS
Fig.1-1: Connect Decorative Gutter Connectors (F1) with Corner Decorative Gutters1 (C1) and Corner Decorative
Gutters 2 (D1) using Short Bolts (CC) and Flat Washers (BB). Tighten with Wrench (LL).
Fig.1-2: Insert Long Decorative Gutters (A1) into Corner Decorative Gutters (C1& D1) using Short Bolts (CC)
and Flat Washers (BB). Tighten with Wrench (LL). (Note: the Corner Decorative Gutters with A1 labels)
Fig.1-3: Insert Short Decorative Gutters (B1) into Corner Decorative Gutters (C1& D1) using Short Bolts (CC)
and Flat Washers (BB). Tighten with Wrench (LL). (Note: the Corner Decorative Gutter with B1 labels)
Loading...