Page 1
General
Please read these instructions carefully before using the system, and always
keep the operating instructions close to hand. Note the warnings in the operation
instructions and always keep the operating instructions close to hand. If you sell
or give the device away, make sure you also hand over these instructions.
Never allow children to use electrical devices unattended.
SAFETY ADVISES
DocumentUK-ARG 16/07/03 19:16 Page 1
Environmental conditions
Protect the device from damp and heat.
Avoid placing the devices in poorly ventilated areas (such as between shelves
or where curtains or furniture can block the vents).
Do not allow foreign bodies or liquids to get into the device. Do not expose
the devices to water.
Naked flames such as lit candles must not be placed on the devices.
The rubber feet on the devices may leave marks on furniture surfaces
Place the devices on a suitable underlay if necessary.
Power connection
Connect the mains adapters to easily accessible 230 V ~ 50 Hz power sockets only.
Use only the mains adapters supplied.
Never try to connect the mains adapters to other connectors as this may
damage the device.
Faults
Remove the mains adapter(s) from the power socket immediately if the mains
adapter, the connection cable or the devices are damaged.
Never try to open and/or repair the devices yourself.
Contact our service centre or qualified personnel.
Environmental protection
All packaging and packaging materials that are no longer required can and should
be recycled.
Health
The low transmitting power of the devices eliminates any danger to health
according to the current state of research and technology
Cleaning and maintanence
Use a dry soft cloth to clean the devices.
Never use cleaning solutions that could damage the surface of the devices.
Never spray cleaning fluids directly onto the devices.
1
Page 2
Zeichnung Gerät 9048.FH11 Tue Nov 16 15:29:26 2004 Seite 2
DESCRIPTION OF THE AUDIO/VIDEO TRANSMITTER
Audio/Videotransmission
antenna
433 MHz
antenna
On/Off
button
12 Volt input (AC adaptor)
Audio input
DESCRIPTION OF THE AUDIO/VIDEO RECEIVER
Audio/Videoreception
antenna
On/Off
button
12 Volt input (AC adaptor)
Audio input
Video input
Channel selector
Channel selector
Video input
2
Infrated LED
connector output
433 MHz
antenna
75 antenna
output
Page 3
Page 4
HOW DOES THE SYSTEM OPERATE
y
t
t
t
t
A
4
T
t
Ins
Infrared
LED
Original
remote control of
the Audio/Video source
Receiver
Transmitter
The transmitter sends an Audio/Video signal fr om the source to the r eceiver.
This 2,4 GHz signal can be broadcasted up to a 100 meters in free field and up to
30 meters indoors. The receiver converts the infrared signals sent by the remote
control of the A/V source into 433 MHz radio frequency signals. The transmitter
will then reconvert these signals into infrared signals in order to contr ol the A/V
device wanted.
DocumentUK-ARG 16/07/03 19:16 Page 4
4
Page 5
1. Insert the 3 plugs of the supplied Audio/Video cable into the inputs of
your A/V transmitter, ensuring to match up the different colours. Plug
the other end of your cable to the double scart plug,; then connect
the scart plug into the scart socket of the selected A/V source. Connect
the original scart cable (not supplied) to the local T.V.
2. Connect the 12 Volts input of the transmitter with the AC adaptor and
then plug it into a standard 230 Volts electric socket.
3. Connect the infrared cable at the back of the transmitter and put one
of the LED on the infrared receiver of the A/V source. You have 2 more
LEDs at your disposal to control 2 additional A/V appliances. It is however
necessary that the 3 appliances are line-connected by scart cables. In this
case, place the scart plug on the last A/V device of the chain. To use the
A/V source device, you have to select it with its remote control.
4. Switch on the transmitter.
5. Select the “A” channel.
6. Point the 2,4 GHz transmission antenna towards the A/V receiver.
7. Straighten up the 433 MHz antenna.
CONNECTING THE AUDIO/VIDEO TRANSMITTER
A TTENTION :
The double scart adaptor must be connected to the scart
socket of the A/V source. If you want to transmit the audio
and video from your PC the installation step 1 is different:
connect the red and white plugs of the second end of the
audio/video cable into the jack 3,5mm/RCA adaptor then
connect the cable into the audio output of your PC; insert
the yellow plug left of the audio/video cable into the video
output of your PC.
Installation example:
IR-LED IR-LED IR-LEDTransmitter
Transmitter
DocumentUK-ARG 16/07/03 19:17 Page 5
5
Page 6
1. Insert the 3 plugs at the Audio/Video cable into the input of your
receiver while minding the different colours. Connect the plugs at the
other end of the cable to the scart adaptor that you will then connect to
the scart socket of the Audio/Video device that will receive the sounds
and images.
If your T.V does not have an Audio/Video scart input, connect the
75 Ohms antenna output of your receiver to the antenna input of your
T.V and adjust it to channel 36.
2. Link the 9 Volts input of the receiver with the A/C adaptor that you
will then plug into a standard 230 Volts electric socket.
3. Switch on your receiver.
4. Select the A canal.
5. Point the receiving antenna towards the transmitter.
6. Straighten up the 433 MHz antenna.
When you wish to receive images and sounds on your T.V, select the scart
input corresponding to the connection, with your remote control, or a
channel set up on channel 43 if the receiver is connected to your T.V by
antenna cable.
CONNECTING YOUR AUDIO/VIDEO RECEIVER
3 pole AV cinch cable
or 75Ω antenna cable
Remote control
Y
t
Receiver
Y
•
•
•
•
•
•
T
•
•
•
•
•
DocumentUK-ARG 16/07/03 19:17 Page 6
6
Page 7
Page 8
TECHNICAL DATA
DocumentUK-ARG 17/07/03 18:32 Page 8
Subject to technical modifications.
Transmitter
AC adaptor Input: 230V ~ 50Hz
Output: 12V 200mA, 2.4VA
Transmitter 4 channels
channel A: 2.411GHz
channel B: 2.434GHz
channel C: 2.453GHz
channel D: 2.473GHz
Power emission: 10mW
Receiver: 433.92MHz
Modulation: FM
Video input signal: 1Vpp (type) / 750 Ohms
Audio input signal: 1Vpp (type) / 600 Ohms
Size: 135x100x140mm
Weight: 185g
Receiver
AC adaptor Input: 230V~ 50Hz
Receiver 4 channels
channel A: 2.411GHz
channel B: 2.434GHz
channel C: 2.453GHz
channel D: 2.473GHz
Video output signal: 1Vpp (type) / 75 Ohms
Audio output signal: 1Vpp (type) / 600 Ohms
Size: 135x100x140mm
Weight: 235g
Output: 9V 400mA 3,6VA
AC adaptor CE-tested.
8
Page 9
Seite KONF-INF.FH11 Fri Sep 09 16:07:46 2005 Seite 15
DISPOSAL
PACKAGING
All packaging and packaging materials that are no longer
required can and should be recycled.
DEVICE
At the end of its life, the appliance must not be disposed
of in household rubbish. Enquire about the options for
environmentally-friendly disposal.
9
Page 10
Seite KONF-INF.FH11 Fri Sep 09 16:07:46 2005 Seite 16
INFORMATION CONCERNING THE
DECLARATION OF CONFORMITY
Hereby, Medion AG declares that MD 9048 is in compliance
with the essential requirements and other relevant provisions of
Directive 1999/5/EC.
For further information concercing the Declaration of Conformity,
please contact our Service Center.
0682
Tested to be used in all EU-countries.
10
Loading...