Medeli DR2 Instruction Manual

Download

Page 1

Page 2

FCC Information

NOTICE

FCC WARNING

GUIDELINES LAID DOWN BY FCC RULES FOR USE OF THE UNIT IN THE U.S.A. (not applicable to other areas)

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio / TV technician for help.

Page 3

IMPORTANT NOTES

Thank you very much for purchasing this product . You are recommended to study this manual carefully before using the unit.

This unit could be operated either by a 3V battery or by a 3V center minus DC adaptor.

Before connection, please ensure the power supply has been properly installed and all power devices such as amplifiers must first be turned off, in order to avoid any malfunction. Avoid using this unit together with same circuit of electronic products that will generate line noises. Do not place this unit too close to heat sources such as radiator and amplifier in order to prevent damages like interference. Do not expose this unit under excessive sunlight, water and moisture.

Strong vibration and shock will damage this unit. Clean this unit with a soft and dry cloth. A slightly dampened cloth with mild detergent might remove stubborn dirt. Never use thinners and alcohol for cleaning the unit. Hold the unit firmly while unplugging the cables, never pull the audio cables with stress.

Note: If the recorder doesn

t w

ork w

ell, p

lease

ull

ower

j ack a

ake

battery, then plug the power jack or put the battery in again to turn on the recorder.

The normal function of the product may be disturbed by Strong Electro Magnetic Interference. If so, simply reset the product to resume normal operation by following the instruction manual. In case the function could not resume, please use the product in other location.

Caution!

Page 4

When to use DR2 ?

This product is suitable in the following situation

Sound sampling in an external or internal environment

Live recording

Conference recording

Course recording for students

Home Studio

Journalist and other situation need interview recording to record

This product provides high quality recording function and accurate

position for sound

It stores file in both wav and mp3

Page 5

MAIN FEATURES

Stereo 4 mics recording,360 degree mode. Support mp3 and wav format.

16bit/24bit,44.1K and 48K sample rate.

Support SD/SDHC card up to 16G.

128*64 OLED display.

Bass compensate, 3D effect, Reverb Chorus Pitch and Delay effect.

MP3 voice cancelling.

Tuner function inside for guitar and bass player.

Easy to operate.

Page 6

SIDE PANEL FRONT PANEL BATTERY REPLACEMENT DIAGRAM MENU TREE BASIC OPERATION

RECORDING SETUP

RECORDING SETUP PLAYBACK PLAYBACK

EFFECTS FILE MANAGEMENT

UTILITY SD CARD MIC SPEAKER PHONES CURRENT STATE PROTECT SPECIFICATIONS

CONTENTS

7-8

9-10

13-26 13-15

16-19 20-22 23-26

27-30 31-34

35-38 39-40

41 41

Page 7

1.POWER supply jack:(DC in 3V center minus)

Connect an AC adaptor to this jack.

2.[POWER ON/OFF] button:

Turn the power on/off.

3.[VOLUME] button:

Adjust volume.

4. [MIC GAIN H..L ] button:

Choose high level mic input or low level input.

5.USB jack

Connect to computer.

SIDE PANEL

Page 8

SIDE PANEL

6.LINE IN jack:

Connect to any other audio device such as mp3 and CD player.

7. EXT MIC jack:

Connect the external microphone.

8. [INPUT LEVEL+/-] button:

You can also adjust the recording level by [INPUT LEVEL +] or [INPUT LEVEL-] button.

9. PHONES jack:

Connect a pair of stereo headphones to this jack.

Page 9

10.[MENU] button :

Press [MENU] button to choose the menu.

11. [BACK/CANCEL] button:

Press [BACK/CANEL] goes back to the home screen. Long press[BACK/CANCEL]button to hold on / off .

12. [REPEAT A B] button:

A-B repeat function allows you to specify point A and point B and automatically play the section between these two points repeatedly.

13. [EFFECT] button:

Effects button to choose.

L RL R

24bit WAVE/MP3

RECORDER

24bit WAVE/MP3

RECORDER

FRONT PANEL

Page 10

14. [MONITOR] :

Headphone monitor output on/off. Long press to turn on/off speaker while playing.

15. [REC] :

Record button

16. [Display]

A variety of information about the unit appears

here.

17. [ ]/[ ]:

[PLAY/PAUSE] button / [Up] button .

18. [ ]/[ ] :

[STOP] button / [Down] button .

19. [ ]/[ ] [F.F] button / [Right] button .

20.[ ]/[ ] [REWIND] button / [Left] button .

L RL R

24bit WAVE/MP3

RECORDER

24bit WAVE/MP3

RECORDER

18 17

FRONT PANEL

Page 11

Size AA,

Sum-3,R6 battery.

Page 12

MENU TREE

File

Play Setup

Utility

Track Select

Play Mode

SD Card

Display

Information

Format

Effect

Effect Type

Open

Delete

Rename

Volume

Auto Gain

Main

Record Setup

Sample Rate

Record Format

Preset

Power

Auto Shutdown

Special

Time/Rate/Pitch

Level/Mix/Feedback

Vocal Enhance

Input Select

Brightness

Dim Light Time

Tuner

Calibration

Page 13

BASIC OPERATION

At the main screen, press [MENU] button, the following menu appears. This screen let you select RECORD SETUP by [ ] or [ ] button.

The screen now indicates five parameter items: SAMPLE RATE REC FO RMAT

INPUT SEL EDT AUTO GAIN and

VOCAL ENHANCE . You c an selec t them

by [ ] or [ ]button .

Press the [BACK/CANCEL] button will return to the main menu .

RECORDING SETUP

00:00:00

00:02:22

DR2-0001.mp3

-48 0-6-12-24-36

STOP FX:off

1.RECORD SETUP

2.PLAY SETUP

3.EFFECT

4.FILE

5.UTILITY

SAMPLE RATE

RECORD FORMAT Mp3 320kbps INPUT SELECT 4 MICS

48kHZ

RECORD SETUP

SAMPLE RATE 48kHZ RECORD FORMAT

INPUT SELECT 4 MICS

Mp3 320kbps

RECORD SETUP

1.RECORD SETUP

2.PLAY SETUP

3.EFFECT

4.FILE

5.UTILITY

00:00:00

00:02:22

DR2-0001.mp3

-48 0-6-12-24-36

STOP FX:off

Page 14

BASIC OPERATION

SAMPLE RATE is sample rate parameter .

you can use [ ] or [ ] button to choose

44.1kHz or 48kHz(default) samplerate.

SAMPLE RATE

REC FORMAT is the parameter for

recording format. This product supports to 9 formats: WAV24bit WAV16bit MP3-320kbps MP3-224kbps MP3-192kbps MP3-160 kbps MP3-128kbps MP3-96kbps and MP3-64kbps .

You can use [ ] or [ ] button to choose.The default is MP3-320kbps.

REC FORMAT

SAMPLE RATE

RECORD FORMAT Mp3 320kbps INPUT SELECT 4 MICS

48kHZ

RECORD SETUP

SAMPLE RATE

RECORD FORMAT Mp3 320kbps INPUT SELECT 4 MICS

44.1kHZ

RECORD SETUP

SAMPLE RATE 48kHZ RECORD FORMAT

INPUT SELECT

4 MICS

Mp3 320kbps

RECORD SETUP

SAMPLE RATE 48kHZ RECORD FORMAT

INPUT SELECT 4 MICS

Mp3 224kbps

RECORD SETUP

Page 15

AUTO GAIN is the switch that adjust input sensitivity use [ ] or [ ] button to choose ON or OFF .The default is ON.

AUTO GAIN

BASIC OPERATION

INPUT SELECT is parameter for number of

microphone to be choosed . select 2 MICS record mode or 4 MICS record mode by [ ] or [ ]button The default is 4MICS.

INPUT SELECT

SAMPLE RATE 48kHZ RECORD FORMAT Mp3 320kbps INPUT SELECT 4 MICS

RECORD SETUP

SAMPLE RATE 48kHZ RECORD FORMAT Mp3 320kbps INPUT SELECT 2 MICS

RECORD SETUP

Note:If you use line in or ext mic, you can choose 2 MIC for only external input or 4 MIC with 2 back MIC and external input together.

VOCAL ENHANCE can enhance the vocal band signal and make less the others use [ ] or [ ]buttonto choose OFF LEVEL ONE and LEVEL TWO .The default is OFF.

VOCAL ENHANCE

AUTO GAIN ON VOCAL ENHANCE

OFF

RECORD SETUP

AUTO GAIN ON VOCAL ENHANCE

LEVEL ONE

RECORD SETUP

AUTO GAIN

VOCAL ENHANCE

OFF

RECORD SETUP

AUTO GAIN

VOCAL ENHANCE OFF

OFF

RECORD SETUP

Page 16

00:00:00

04:36:22

DR2-0001.mp3

-48 0-6-12-24-36

PUAS FX:off

RECORDING

At the main screen or file manage screen (FILE) ,press the [REC] button goes into standby record mode. The [REC] button lightens and flashes.

We can see two highlight record levels are scanning. This product detects the level of the currently selected input source. The current file name displays under the record level (eg:DR2-xxxx.mp3 or DR2-xxxx.wav).

00:00:00

04:36:22

DR2-0001.mp3

-48 0-6-12-24-36

BASIC OPERATION

STOP FX:off

Page 17

Adjust the record level by pressing

[INPUT LEVEL+] [INPUT LEVEL-] button so that the highlight record level reaches thehighest level without the peak indicator shown in red turning on .

00:00:00

04:36:22

DR2-0001.mp3

-48 0-6-12-24-36

PUAS FX:off

MIC GAIN: 16

BASIC OPERATION

Page 18

At the standby condition, Press [PLAY/ PAUSE] or [REC] button to start recording The [REC] button lightens . the time level begin to increase as recording starts. The time show above indicate the record time, and the time appeals on the right side indicates the time left for record.

Note: the amount of record time available depend on capacity of SD card.

You can also adjust the recording level by [INPUT LEVEL+] or [INPUT LEVEL-] button while recording.

Note: if you use the input MIC, the sound of pressing the key will simultaneously be recorded.

00:00:01

04:36:21

DR2-0001.mp3

-48 0-6-12-24-36

REC FX:off

BASIC OPERATION

Page 19

Adjust the output volume by pressing [VOLUME+] or [VOLUME-] at the left side.

Press [PLAY/PAUSE] button to pause the recording . Press the [PLAY/PAUSE]

button again to continue recording.

During recording , press [STOP] button or [REC] button to stop the record, Light on [REC] button darkens,and the file will be saved to the SD card.

00:02:11

04:36:21

DR2-0001.mp3

-48 0-6-12-24-36

VOLUME: 20

00:11:49

04:25:37

DR2-0001.mp3

-48 0-6-12-24-36

00:00:00

00:12:12

DR2-0001.mp3

-48 0-6-12-24-36

BASIC OPERATION

REC FX:off

STOP FX:off

Page 20

SETUP PLAYBACK

At the home screen , press [MENU] button to go into the main menu. Use [ ] or [ ] button to choose play setup then press [MENU] button to go into the playback setup screen .

Use [ ] or [ ] button to edit the parameters such as TRACK SELECT ,

BASS C OMP , PLAY M ODE and

VOLUME .

Press [BACK/CANEL] to go back to the home screen.

00:00:00

00:02:22

DR2-0001.mp3

-48 0-6-12-24-36

1.RECORD SETUP

2.PLAY SETUP

3.EFFECT

4.FILE

5.UTILITY

TRACK SELECT

SPECIAL

OFF PLAY MODE ONCE

STEREO

PLAY SETUP

1.RECORD SETUP

3.EFFECT

4.FILE

5.UTILITY

2.PLAY SETUP

TRACK SELECT STEREO

SPECIAL

PLAY MODE ONCE

OFF

PLAY SETUP

BASIC OPERATION

STOP FX:off

Page 21

TRACK SELECT controls selection of playback channel . Press [ ] or [ ] button to choose the channel among STEREO(default), LEFT, RIGHT and VOCAL CUT.

TRACK SELECT

PLAY MODE controls playback mode. We can use [ ] or [ ] button to choose the mode such as ONCE (default), LOOP, LOOP ALL.

PLAY MODE

TRACK SELECT

SPECIAL OFF PLAY MODE ONCE

STEREO

PLAY SETUP

TRACK SELECT STEREO SPECIAL

PLAY MODE ONCE

OFF

PLAY SETUP

TRACK SELECT

SPECIAL OFF PLAY MODE ONCE

LEFT

PLAY SETUP

TRACK SELECT STEREO SPECIAL OFF PLAY MODE LOOP

PLAY SETUP

BASIC OPERATION

SPEAIAL is the special effect open when playback.

You can use [ ] or [ ] button to choose bass compensate or 3D effect. Bass compensate can compensate the low frequency signal and 3D effect can offer you a surrounding effect.The default is OFF.

SPEAIAL

In Voice Cut, the melody on the mp3 file could be muted, leaving the background music playing. Note:This function will be effective only for the normal mp3 files,and could not be effective if the mp3 file has only one melody track or thebackground is in both 2 tracks.

Page 22

VOLUME controls playback volume. You can use [ ] or [ ] button to adjust the playback volume from 0 to 32. Default parameter is 20.

VOLUME

VOLUME 21

PLAY SETUP

BASIC OPERATION

Page 23

This product supports playback files of MP3 and WAV .

PLAYBACK

At the home screen, you can use [PLAY/PAUSE] button to start playing the file , press [PLAY/ PAUSE] button for the second time to pause the playing , press [PLAY/PAUSE] button for the third time to continue playing. The recorder playback the current song according to the playback setup (ONCE, LOOP, LOOP ALL).

Press [STOP] button to stop the current playing.

You can also playback the file by this way . go into the file manage screen (MENUFILE), select the file you need and press the [MENU] button.

00:00:00

00:02:22

DR2-0001.mp3

-48 0-6-12-24-36

00:01:18

00:02:22

DR2-0001.mp3

-48 0-6-12-24-36

1.RECORD SETUP

2.PLAY SETUP

3.EFFECT

5.UTILITY

4.FILE

1.RECORD SETUP

2.PLAY SETUP

3.EFFECT

4.FILE

5.UTILITY

DR2-xxx1.MP3

DR2-xxx2.

MP3

DR2-xxx3.MP

FILE LIST

BASIC OPERATION

STOP FX:off

PLAY FX:off

Page 24

00:01:18

00:02:22

DR2-0001.mp3

-48 0-6-12-24-36

Choose the OPEN at the files edit menu and press the [MENU] button to start playing the selected file.

At the home screen, when file is playing, press the [F.F] button to go to next file

Press [rewind] button to return to the beginning of the current file, Press [rewind] button again to go to previous file .

While playing,Hold [REWIND] button to fast search to the beginning of the current file.

While playing,Hold [F.F] button to fast search to the end of the current file. Continue holding the

[F.F] button will enter the next file and continue to fast search . If the A-B repeat function is on, holding the [F.F] button would not exceed the point B.

1.OPEN

2.DELETE .RENAME3

FILE LIST

00:01:18

00:03:20

DR2-0002.mp3

-48 0-6-12-24-36

BASIC OPERATION

PLAY FX:off

Page 25

The A-B repeat function allows you to specify point A and point B and automatically play the section between these two points repeatedly.

While playing, press the [REPEAT A-B] button for the first time to locate the start point for the range to be repeated.

Press the [REPEAT A-B] button for the second time to locate the end point for the range to be repeated .if the point B before point A , the setting will not be saved .

Press the [REPEAT A-B]button for the third time will cancel this setting.

00:0:20

00:03:20

DR2-0002.mp3

-48 0-6-12-24-36

00:1:45

00:03:20

DR2-0002.mp3

-48 0-6-12-24-36

PLAY FX:off

00:0:22

00:03:20

DR2-0002.mp3

-48 0-6-12-24-36

PLAY RPT A

00:1:30

00:03:20

DR2-0002.mp3

-48 0-6-12-24-36

PLAY RPT A-B

BASIC OPERATION

PLAY FX:off

Page 26

The volume of playback can be controlled by the volume of PLAY SET . The [VOLUME+] [VOLUME -] button on the left side panel can also adjust the volume of the recorder.

00:1:45

00:03:20

DR2-0002.mp3

-48 0-6-12-24-36

PLAY FX:off

VOLUME 21

BASIC OPERATION

Page 27

EFFECT

In home screen ,press [MENU] button to go into the main menu, use [ ] or [ ] button to select EFFECT and press [MENU] button to enter the effect type .

The corresponding parameters of the effect will change to follow the effect type.Press[ ] or [ ]button to select effect parameter . Press[ ] or [ ] button to adjust the value for in the selected parameter .

Press [BACK/CANCEL] button can back to the home screen.

1.RECORD SETUP

2.PLAY SETUP

4.FILE

5.UTILITY

3.EFFECT

1.RECORD SETUP

2.PLAY SETUP

3.EFFECT

4.FILE

5.UTILITY

EFFECT EDIT

EFFECT TYPE OFF

EFFECT EDIT

EFFECT TYPE ROOM TIME

LEVEL 20

Press the [ ] and [ ] for effect type change , including OFF ,ROOM, HALL , CHORUS ,PITCH SHIFT, DELAY .The default is OFF.

EFFECT EDIT

EFFECT TYPE

TIME 20 LEVEL 20

ROOM

EFFECT EDIT

EFFECT TYPE ROOM TIME

LEVEL 20

BASIC OPERATION

Page 28

Hall provides the grand musical ambience that is experienced listening to music in a hall Time and Level can be set arrange from 0 to 32.

HALL:

Room provides warm musical ambience that is experience while listening to music in a room. Time and Level can be set arrange from 0to 32.

ROOM:

Effect is Off .

OFF:

EFFECT EDIT

EFFECT TYPE OFF

EFFECT EDIT

EFFECT TYPE

TIME 20 LEVEL 20

ROOM

EFFECT EDIT

EFFECT TYPE H TIME 20 LEVEL 20

ALL

BASIC OPERATION

Page 29

Pitch shift copies the incoming signal, then shifts the pitch of the copy to a different note .the shifted note is then mixed back with the original, sounding as if two guitars were playing different notes. The Pitch can be set arrange from -12 to 12 , the Mix can be set arrange from 0 to 32.

PITCH SHIFT:

DELAY:

Delay is an effect that records a portion of the incoming signal, then play back in a preset time. Time and Feedback can be set arrange from 0 to 32 .

The Chorus effect combines delay time and amplitude modulation to effectively thicken and add warmth to the sound . Rate and Level can be set arrange from 0 to 32.

CHORUS :

EFFECT EDIT

EFFECT TYPE

RATE 20 LEVEL 20

CHORUS

EFFECT EDIT

EFFECT TYPE

PITCH 8 MIX 20

PITCH SHIFT

EFFECT EDIT

EFFECT TYPE

TIME 13 FEEDBACK 13

DELAY

BASIC OPERATION

Page 30

In home screen ,You can also press [EFFECT] button to select Room, Hall ,Chorus ,Pitch Shift, or Delay .

The effect will automatically turn off when you start recording .

00:0:20

00:03:20

DR2-0002.mp3

-48 0-6-12-24-36

STOP FX:off

00:0:20

00:03:20

DR2-0002.mp3

-48 0-6-12-24-36

STOP FX:room

00:0:20

00:03:20

DR2-0002.mp3

-48 0-6-12-24-36

STOP FX:hall

BASIC OPERATION

Page 31

In home screen , press the [MENU] button to ENTER the main menu. Press [ ] or [ ] button to choose FILE and press the [MENU] button to go into the file manage interface , the screen display the file list of the root directory .

Use [ ] or [ ] button to choose file or subdirectory, press [MENU] button to enter the subdirectory ,then the file list of current directory will display.

Use [MENU] button after selection to enter the file edit menu, you will see the three option : OPEN , DELETE , RENAME . Press the [BACK/CANCEL] button to go back to the file manage screen.

FILE MANAGEMENT

1.RECORD SETUP

2.PLAY SETUP

3.EFFECT

5.UTILITY

4.FILE

1.RECORD SETUP

2.PLAY SETUP

3.EFFECT

4.FILE

5.UTILITY

Dr2-0001.MP3

Dr2- 2.

000 MP3

Dr2-0003.MP

FILE LIST

DR2-0001.MP3

DR2-0003.MP3

DR2-0002.MP3

FILE LIST

1.OPEN

2.DELETE .RENAME3

FILE LIST

BASIC OPERATION

Page 32

choose the DELETE to delete the file , then press the [MENU] button . confirmation message for deletion appears.

Press [MENU] button to confirm .

Press [BACK/CANCEL] button to cancel this

operation and return the file edit menu.

choose the OPEN press [MENU] button to play the file, the screen will go back to the home screen.

OPEN

DELETE

00:00:01

00:03:20

DR2-0002.mp3

-48 0-6-12-24-36

PLAY FX:off

1.OPEN

2.DELETE .RENAME3

FILE LIST

1.OPEN

3.RENAME

2.DELETE

FILE LIST

ARE YOU SURE

BASIC OPERATION

Page 33

choose RENAME to rename the file,

then press the [MENU] button,the

current file name appears.

Use [ ] or [ ] button move the cursor .

after use [ ] or [ ] button select the

character ,

press [MENU] button to confirm .

RENAME

1.OPEN

2.DELETE

3.RENAME

FILE LIST

DR2-0002

RENAME

DR2-0002

RENAME

DR2-00 20

RENAME

DR2-00 21

RENAME

DR2-0001.MP3

DR2-0003.

MP3

DR2-00012.MP

FILE LIST

BASIC OPERATION

Page 34

if a file with the same name already exists in

the folder, a message appears and the name

change cannot be executed .

Press [MENU] to edit the name.

Press [BACK/CANCEL] button to exit the edit menu.

DR2-0003

RENAME

SAME FILE NAME EXISTS PRESS [BACK] TO CANCEL

PRESS [MENU] TO REEDIT

DUPLICATE NAME

BASIC OPERATION

Page 35

UTILITY

At the home screen, press [MENU] to go to the main menu .press [ ] or [ ] button choose UTILITY . Five items SD CARD

DISPLAY PRESET POWER and TUNER will be listed on the screen . use [ ] or [ ] button to choose the item.

Press [BACK/CANCEL] button to return to the home screen.

SD CARD

choose SD CARD , press the [MENU] button to enter the SD menu, there are two operation INFORMATION a nd FORMAT . You can use[ ] or [ ] button to choose .

Press [BACK/CANCEL] button back to return to utility menu.

1.RECORD SETUP

2.PLAY SETUP

3.EFFECT

4.FILE

5.UTILITY

1.RECORD SETUP

2.PLAY SETUP

3.EFFECT

4.FILE

5.UTILITY

1.SD CARD

2.DISPLAY

3.PRESET

4.POWER

5.TUNER

UTILITY

1.INFORMATION

2.FORMAT

SD CARD

1.INFORMATION

2.FORMAT

SD CARD

BASIC OPERATION

1.SD CARD

2.DISPLAY

3.PRESET

4.POWER

5.TUNER

UTILITY

Page 36

Choose FORMAT , press [MENU] button . this initialization process will erase all information stored on the SD card, and the information cannot be retrieved. Perform this operation with care. The screen will display the warning message. Press [MENU] to confirm.

Press [BACK/CANCEL]button to cancel this initialization process.

Press [MENU] button again ,Confirmation message for formation (ARE YOU SURE?)appears.

1.INFORMATION

2.FORMAT

SD CARD

Choose INFORMATION , then press the [MENU] button ,the screen displays the information of SD card such as capacity ,used capacity and the free capacity. press [BACK/CANCEL] button back to SD card menu

1.INFORMATION

2.FORMAT

SD CARD

SD INFORMATION

CAPACITY 952 MB USED 342 MB FREE 610 MB

DATA IN SD WILL LOST PRESS [BACK] TO CANCEL

PRESS [MENU] TO PROCESS

BASIC OPERATION

SD FORMAT

Page 37

DISPLAY

choose DISPLAY ,press [MENU] button . the parameter of BRIGNTNESS and

DIM LIGHT TIME appears ,You can use [ ] or [ ] button to choose .

you can use[ ] or [ ] button adjust the BRIGHTNESS of LCD. The BRIGHTNESS can be set arrange from 1 to 32,the default is16 .

You can use[ ] or [ ] button adjust the DIM LIGHT TIME by 5 minutes, 10 minutes,20 minutes, 1 hour or DIM OFF .

Press [BACK/CANCEL]button to return to utility menu.

1.SD CARD

3.PRESET

4.POWER

5.TUNER

2.DISPLAY

UTILITY

BRIGHTNESS

DIM LIGHT TIME 00:00:20

DISPLAY

BASIC OPERATION

Press [MENU] to confirm,the screen will display Processing............,then begin to format ,

After finishing the operation the display will go to the SD menu .

BRIGHTNESS

DIM LIGHT TIME 00:00:20

DISPLAY

Page 38

POWER

choose POWER ,press [MENU] button . the screen displays the auto power off time. Press [ ] or [ ] button to adjust auto power off time by 5 minutes, 15 minutes, 30 minutes, 1 hour or DISABLE.

1.SD CARD

2.DISPLAY

3.PRESET

5.TUNER

4.POWER

UTILITY

AUTO SHUT DOWN 00:30:00

POWER

AUTO SHUT DOWN 01:00:00

POWER

BASIC OPERATION

PRESET

choose PRESET , press [MENU] button . the screen will display the warning message to confirm the loading of factory reset . Press [BACK/CANCEL] to cancel and return to the utility menu. Press [MENU] button the screen will display ARE YOU SURE?

Press [MENU] button again,the screen will display PROCESSING....... ,then load the default

parameters. After finishing the operation the display will return to utility menu.

1.SD CARD

2.DISPLAY

4.POWER

5.TUNER

3.PRESET

UTILITY

LOAD FACTORY PRESET! PRESS [BACK] TO CANCEL, PRESS [MENU] TO PROCESS

PRESET

TUNER

choose TUNER ,press [MENU] button to enter the TUNER menu. Press [ ] or [ ] button to adjust Calibration from 435-445Hz The default is 440HZ .

1.SD CARD

2.DISPLAY

3.PRESET

4.POWER

5.TUNER

UTILITY

CALIBRATION 440

TUNER

Page 39

This product supports SD card to exchange data between recorder and PC or other peripheral equipments . Format the card before using it .Most preferable to use the recorder's format function to ensure the compatibility of the card.

This product supports SD and SDHC card up to 16G . Product being connected to the computer or the other equipments used as host , will be recognised as an USB storage device .the screen will display only USB connection and the recorder forbids other operations until the USB cable disconnection.

SD CARDS:

Note: In order to avoid any error, please do not eject the SD card while USB

cable is connected.

BASIC OPERATION

Note: When you insert a SD card with the improper format, the recorder will

display SD NEED FORMAT! Press [MENU] to confirm Press [Back] to

cancel .

Page 40

Note:In order to avoid any error, please shut down the recorder when inserting a SD card .

BASIC OPERATION

Page 41

MIC:

This product has 4 high-powered stereo MICs inside and can be used as a high quality microphone . Press [MONITOR] button to turn on or turn off the output function form the phone jack.

Press [INPUT LEVEL +/-] to change the input level.

Press[MONITOR] button and hold on to turn on / off the speaker.

PHONES:

Connect the headphone to the product. The [VOLUME +/-]button are used to adjust the output level.

00:00:00

04:36:22

DR2-0001.mp3

-48 0-6-12-24-36

Monitor off

00:00:00

04:36:22

DR2-0001.mp3

-48 0-6-12-24-36

MIC GAIN: 16

Headphones

BASIC OPERATION

SPEAKER:

STOP FX:off

Page 42

CURRENT STATE PROTECT :

Hold [BACK/CANCEL] to start the hold function Display show HOLD KEY ON

It will lock all the keys on the panel,

except the USB connection and power off.

Hold on the [BACK/CANCEL] button again to turn off this condition with display

HOLD KEY OFF .Then all the keys on the

panel will be unlock.

00:00:00

04:36:22

DR2-0001.mp3

-48 0-6-12-24-36

HOLD KEY ON

00:00:00

04:36:22

DR2-0001.mp3

-48 0-6-12-24-36

HOLD KEY OFF

BASIC OPERATION

STOP FX:off

Page 43

SPECIFICATIONS

Power Requirements: AC adaptor DC3V center minus type or SIZE AA,SUM-3,R6 battery

Dimensions: 108(L) x 67.5(W) x 28.5(H) mm

Weight: 97g without battery

Page 44

Version:G13