Medeli DP660 Instruction Manual

Page 1

Page 2

Welcome...

Thank you for purchasing our Digital Piano. The use of high technology and the most advanced sampling technique brings you high quality sound and enjoyment. The combination of digital piano and electronic keyboard features let you perform perfectly. We hope this digital piano will be able to explore your creativity, and brings you unlimited happiness and music enjoyment. Before you use the piano, we recommend you to read through this manual. Please keep this instruction manual for future reference.

Precautions!

Please read the following carefully before use:

Do not expose the piano to high temperature, direct sunlight and excessively dusty places.

Do not place the piano too close to other electrical appliances such as television and radio. It may cause interference.

Do not place the piano to excessive humid area. Avoid putting container with liquid on top of the piano for preventing the damage of the internal parts of the piano by flowing liquid.

Always unplug cables by gripping the plug firmly, but not pulling on the cable.

Do not apply excessive force to the switches and buttons.

When the piano is not in use or in the time of thunderstorm, please remember disconnect the power supply.

Avoid adjusting the volume level to the maximum or to the levels that you feel uncomfortable, we recommend you to limit the volume level to two-third of the max for preventing the damage of audiory sense.

Unplug the power cable before cleaning the piano,and do not connect or disconnect the power cable with a wet hand.

Check and clean the power plug periodically.

To avoid damage to the piano and other devices to which it is connected, turn the power switches of all related device off prior to connecting or disconnecting cables.

Clean the piano with a dry soft cloth or a slightly damp cloth to remove dirt as well.

Never use cleaners such as thinner or alcohol. To prevent damage the surface of the LCD display, please use lens cleaning tissue to clean the display.

If the piano cable is damaged, please do not use the piano. Otherwise it may cause fire or electrical hazard.

In the case of malfunction due to improper handling the piano, please switch off and on again after 30 seconds.

Do not attempt to disassemble or repair the internal parts of the piano by yourself. If the piano does not work properly, please contact the approved repairer.

During the process of ESD test, if the piano does not work properly, please restart it for normal mode.

NOTE:

Page 3

Contents

Set-up Guide General Guide The Connectors

1. Using the AC power jack

2.Using headphones

3.Using the AUX.OUT jack

4. Using the foot pedals

5.Using the MIDI IN/OUT jacks

Basic Operation

Power switch & volume

Voice and Effects

1.Voice selecting

2.Dual voice

3.Lower voice

4.Split point

5.Piano

Keyboard Function

1.ABC on

2.Naming

3.Portamento & Modulation

4.Sustain

Auto Accompaniment

1.Play the style(only drum)

2.Play the style(all tracks)

3.The accompaniment section

4.Accompaniment operation

Chord Recognize Volume Control

Accomp volume control Keyboard volume

Tempo Metronome One Touch Setting Memory Demonstration Album Song

Function

1.Transpose

2.Tune

3.Octave

4.Beat

5.Touch

6.Split point

7.Key select

8.Portamento time

9.PAD assign

10.DSP on/off

11.Reverb type

12.Reverb level

13.Chorus type

14.Chorus level

15.Local on/off

16.Receive channel

17.Transmit channel

18.Default parameters

Disk

1.Using floppy disks

2.Disk utility

3.Disk save

Record

1.Start recording

2.Playback recording

MIDI

1.What is MIDI

2.MIDI connection

3.MIDI application

Specifications Appendix 1-Voice List Appendix 2-Style List Appendix 3-Demo List Appendix 4-Song List Appendix 5-Album List Appendix 6-Chord Chart Appendix 7-MIDI Chart

3-5 6-7 8-9

8 8 8 9 9

10-11

10 10

11 11 11

12-13

12 12 12 13

13-15

13-14

14-15

16 17

17 17

18 18

18-19

19-20

20 20

21-24

21 21 21 21 21 22 22 22

22-23

23 23 23 23 23 24 24 24 24

25-30

25-26 26-29 29-30

30-31

32 32 32

33 34 35 36 36 37 38 39

Page 4

Main Features

88 graded Hammer key.

Multi-functional LCD which can display the staff.

Use the +/- key or dial to select voice, style or song.

Function features that include transpose, tune, octave, split point, pedal select, touch, DSP, midi etc.

142 high quality voices at all, including 128 GM Voices.

100 auto accompaniment styles, from 001 to 100.

8 demos of different style.

60 songs that have melody off mode.

100 albums that offer you some good classic music setting.

8 banks with 6 memories each .

Both Single finger detect and fingers detect.

Each record song has 5 tracks--1 accomp track and 4 melody tracks.

Portamento and Modulation, 4 level portamento sensitivity.

Mixer function including the volume adjustment of Voice R1, Voice R2, Voice L, Drum, Bass, Chord1,Chord2,Chord3,Accomp.

Pedal selection function including sustain, soft, accomp start, tempo tap, and memory select.

DSP function that can set the level of Reverb and Chorus .

MIDI IN and MIDI OUT function, and you can select which channel to receive or transmit midi message.

Dual, Lower voice, Sustain, Piano, O.T.S etc.

Floppy disk driver. You can play standard midi music files(format 0,format 1),and save midi files from recorded data.

Page 5

Set-up Guide

Open the package, and check whether the following parts are available:

1. Piano body

2. Music stand

3. Right leg component

4. Left leg component

5. Center supporting board

6. Foot pedal unit

7. Hand screw (4 pcs.)

8. Screws (8 pcs.)

9. Screw caps (8 pcs.)

10. Power cable stabling hook (2 purchase.)

11.Floppy drive

Page 6

Follow the illustration below and finish off the set-up procedures.

Caution: When setting up the piano, please use the screws supplied and avoid using the

unspecified screws which may damage the piano body and cause the lost of stability.

Parts required in this step:

7. Hand screws x 4

8. Screws x 8

9. Screw caps x 8

Put the foot pedal unit(6) in between the left and right legs components (3&4).Use 4 pieces of screws (2 on each side) to stable the legs onto the foot pedal unit. (Make sure the direction of the placement is correct before screwing)

Page 7

Use 4 pieces of screws (2 on each side) to stable the center supporting board (5) onto the assembly finished in Part A on the previous page.

Put the piano body(1) on the top of the assembly finished in part B, and use 4 pieces of hand screws to stable afterward.

After the initial set-up, stick the cable stabling hook(10) on the internal side of the leg component (see the below illustration for reference).

Cable stabling hook

Page 8

General Guide

Top View

Rear View

Front View

Control Panel Pedal Jack MIDI IN/OUT Jack AUX. OUT Jack AC Power Jack

Headphones Jack Soft Pedal Sustenoto Pedal Sustain Pedal Music Stand Piano Keyboard

Page 9

STYLES

OFF

ACCOMPANIMENT CONTROL

01 8 Beat 1 07 16 Beat 1 15 Ballad 1 34 BigBand

23 SlowRock 1

73 March 1 79 Waltz 1 92 XinJiang

94 NeiMengGu

85 Pianist

52 Pop Bossa

57 Samba 1

66 Beguine

46 CountryShuf

63 Pop Reggae

06 8 Beat Pop 08 16 Beat 2 29 Disco 1

38 Swing 1

22 Rock'N'R

51 Bluegrass 55 Rhumba 1 64 Tango 69 Bounce

61 PopChaCha

76 Polka 93 YunNan 95 JiangNan

00 Custom80 SlowWaltz

SEQUENCER

START / STOP SYNC

FILL-IN A FILL-IN B

INTRO / ENDING

PLAY / STOP

ACCOMP /

CLEAR

MELODY 1 MELODY 2 MELODY 3 MELODY 4

O.T.S.

FUNCTION+

/NEXT

FUNCTION-

/BACK

TEMPO TEMPO

RECORD

PORTAMENTO

SPLIT / LOW VOICE

MIXER

SUSTAIN

A.B.C./

MELODY OFF

ALBUM/SONG/

STYLE

DUAL

VOICE

DEMO

VOICES

49 StringEns 1

01 GrandPno

05 E.Piano 1

09 Celesta

22 Accordion

25 Nylon Gtr 37 SlapBass 117 DrawOrgan

69 Oboe

129 Pipa 134 Erhu

138 Qudi

74 Flute

141 C. Percus

55 SynVoice

63 SynBrass 146 Pizz. Str

58 Trombone

51 Syn. Strs 1

61 FrenchHorn

72 Clarinet 132 Guzheng 136 Hi-Suona

139 Bangdi76 PanFlute 142 Percus

07 Harpsi. 13 Marimba 23 Harmonica

27 Jazz Gtr

41 Violin04 Honky-Tonk

20 Ch-Organ

57 Trumpet

62 BrassSect 67 TenorSax

47 Harp

53 ChoirAah50 StringEns 2

60 MuteTrump

ONE TOUCH CONTROL

/ NO

/ YES

M 1 M 2

M 3

M 4

M 5 M 6

BANK

STORE PIANO METRONOME

DISK SAVE UTILTY

VOLUME

MAXMIN

POWER

MODULATION

232220

A.B.C

SPLIT

PORTAMENTO

MODULATION

TEMPO/MEASURE/BEAT

DUAL

TOUCH

MELODY OFF

SUSTAIN

CHORD

M1/M2/M3/M4/M5/M6/O.T.S

DISK/DSP

VOICE LR12/STYLE/SONG

TREBLE CLEF

BASS CLEF

RECORD

PLAY/STOP

ACCOMP/CLEAR

MELODY 1/2/3/4

MODULATION

Front panel

POWER SWITCH

MASTER VOLUME

ACCOMP/CLEAR

ACCOMPANIMENT CONTROL

-START/STOP

-SYNC

-FILL-IN A

-FILL-IN B

-INTRO/ENDING

SEQUENCER

-MELODY 1

-MELODY 2

-MELODY 3

-MELODY 4

RECORD

PLAY/STOP

OTS

FUNCTION

TEMPO

PORTAMENTO/MODULATION

A.B.C/MELODY OFF

SPLIT

MIXER

SUSTAIN

DEMO

DUAL

VOICE

ALBUM/SONG/STYLE

PIANO

METRONOME

DISK

SAVE

UTILITY

ONE TOUCH CONTROL

-BANK

-STORE

-M1-M6

DIAL/[+/YES]/[-/NO]

LCD display

Page 10

The Connectors

Turn the volume switch anti-clockwise to reach the minimum volume level.

Plug the power cable into an AC power outlet.

If you have done the above procedures you are now safe to turn on the piano.

When the piano is not in use or in the time of thunderstorm, please disconnect the power for safety sake.

An optional set of stereo headphones can be connected to the headphones jack located on the left underside of the piano body. When a pair of headphones is connected to the jack,the internal speakers will switch off automatically.

Never use the headphone with high volume, as it may hurt your ears. To prevent the damage of the speakers, ensure that the volume is set to the minimum level before connecting the power and other devices.

Connect the rear-panel AUX.OUT jack to amplified speakers, amplifiers or domestic hi-fi-units for external amplification.

Connect both left(L) and right(R) channels for the stereo result. If you only connect either one of the channels, the connected channel will only take effect.

Using headphones

Using the AUX.OUT jack

Using the AC power jack

Ensure the piano is turned off when connecting and disconnecting the power.

Connect the power cable to the AC power jack on the underside of the piano body.

CAUTIONS!

NOTE:

POWER

OFF ON

Page 11

Using the foot pedals

MIDI stand for Musical Instrument Digital Interface. MIDI is a world wide standard that makes it possible for various electronic musical instruments and other devices.

Data transmitted from other MIDI instrument via MIDI is received at this terminal.

Data produced by the Digital Piano is transmitted to other MIDI instruments via MIDI from this terminal.

Using the MIDI IN/OUT jacks

Connect the plug of the foot pedal unit to the pedal jack on the rear panel. You will experience the sustain effect.

MIDI IN:

MIDI OUT:

Basic Operation

Power switch & volume

Turn the [POWER] switch on.The LCD display lights up.

Use the volume control switch to adjust the volume to your desired level.

If the LCD display does not light up after you turned on the piano, please check the power supply. If the piano is silent, the volume may be adjusted to its minimum level.

NOTE:

POWER

OFF ON

Page 12

Vocies and Effects

Voice selecting

Voice numeber

142 voice at all (Appendix 1), including 128 GM voice, 12 Chinese voices, and 2 percussion voices.

Voice setting

Press [VOICE] button to select three separate voice modes: VOICE R1,VOICE R2,VOICE L. The default VOICE R1 is No.001; LCD displays "VOICE R1"and the voice name.

Press [+/YES]/[-/NO] button or use dial to select the voice wanted.

Use 20 voice direct select keys to select the voice with direct voices in each botton (upper & nether)

When change the voice, pay attention to the rules. If press the same button, the voice will be

changed between upper and nether. If one direct button is the upper (nether) voice,

the voice is also the upper(nether) when pressing other direct bottons.

/ NO

/ YES

VOICE

NOTE:

DUAL

Dual voice

3 4

Press [DUAL] button to turn on the DUAL VOICE. When VOICE R1 is lightened off , VOICE R2 and dual flag are both lightened. The dual voice name is also displayed on the LCD.

Press [+/YES]/[-/NO] button or the dial to select the dual voice number. The default dual voice number is No. 50: Strings2.

Press [DUAL] button again to turn off the DUAL VOICE.

Select the dual voice with the Direct Voice keys.

Page 13

PIANO

Lower voice

Split point

Piano

You can split the keyboard to right and left area in this function.

Press [SPLIT/LOW VOICE] button to turn on the lower voice. LCD lights the lower voice flag and displays "VOICE L" and the lower voice name.

Press [+/YES]/[-/NO] button or the dial to select the lower voice number. The default lower voice number is No. 50: Strings2.

Press [SPLIT/LOW VOICE] button again to turn off the lower voice.

Split point(#F)

VOICE L VOICE R1/R2

SPLIT / LOW VOICE

Select the lower voice with the Direct Voice buttons.

In the Split Voice mode, you can assign two different Voices to opposite sections of the keyboard, and play one Voice with your left hand while your right hand plays another voice.

#F3 is the default split point. Each key on the keyboard can be set as the split point, and be stored in the memory.

Press [PIANO] to the piano mode. The LCD displays PIANO, and the voice is changed to piano immediately. At that time, ABC, DUAL, and LOWER are all OFF.

Press [PIANO] again or press any of keys as follows :[DEMO]/[VOICE]/[ALBUM/SONG/ STYLE]/[DISK]/[SAVE]/[UTILITY]/[PLAY/STOP]/ [ALBUM/SONG/STYLE]/[BANK] and the memory keys will exit the PIANO mode. The voice will no longer retain as the piano voice.

You can select the style number with the [+/YES]/ [-/NO] key, or the wheel at the PIANO mode. Press the [START/STOP] key to play the style (Only drum) .

The MIXER and FUNCTION menu can be functioned.

Page 14

Keyboard Function

ABC on

Naming

Portamento

Modulation

SPLIT POINT(#F3)

VOICRE R1/R2ACCOMP

The keyboard not only plays three voices at the same time, but also has other necessary functions.

Turn ABC on. The left area of keyboard is chord area. When you play the chord, both the bass and the chord voice will phonate.

If you want to save a midi file or memory file,you can name this file with the keyboard.

SHIFT

DELETE

B D E

G I K L N P Q S U W X Z 1 2 4 6 8 9 # % & ( @ {

A C F H

M O R T V Y 0 357 1

)

While holding down the [PORTAMENTO] button, you can play the keyboard. The note will have portamento effect.(See the chart) This keyboard has four kinds of portamento time (0-3). The default is 2. (you can modify the portamento time with function menu)

You can set [PORTAMENTO] button to modulation function.(See FUNCTION MENU) LCD will display the portamento icon.While holding down the [PORTAMENTO] button you can play the keyboard. The note will have modulation effect.

Page 15

Sustain

Press the [SUSTAIN] button to turn the SUSTAIN effect on. The sustain icon will appear next to "sustain" on the LCD. All notes played on the keyboard will have a longer sustain effect.

When the Sustain feature is ON, press the [SUSTAIN] button to turn the SUSTAIN effect OFF.

SUSTAIN

Auto Accompaniment

Press the [ALBUM/SONG/STYLE] button, or the direct style button.

Select a style. Select the desired style number with dial,[+/YES], [-/NO],or direct style keys. (See Style Chart)

Press the [START/STOP] button to start/stop playing the style (only drum).

Play the style(only drum)

Play the style (all tracks)

/ NO

/ YES

ALBUM / SONG

STYLE

A.B.C/

MELODY OFF

ACCOMPANIMENT CONTROL

START / STOP SYNC

FILL-IN A FILL-IN B

INTRO / ENDING

Press the [ALBUM/SONG/STYLE] button, or the direct style button.

Select the desired style number with dial,[+/YES], [-/NO] or direct style buttons.

Press the[ABC/MELODY OFF]button.The A.B.C icon will appear next to "A.B.C" on the LCD. This keyboard automatically plays bass and chord parts in accordance with the chords you finger. The relevant chord name will be shown above "CHORD" on the LCD.

Page 16

Sync start Press the [SYNC] button. The Beat display will flash at the current tempo when the synchronized start mode has been selected. The keyboard will start to play the accompaniment by pressing "recognized" chord.

Play another chord.

Press the [START/STOP] button to stop playing the style.

START / STOP

SYNC

ACCOMPANIMENT CONTROL

START / STOP SYNC

FILL-IN A FILL-IN B

INTRO / ENDING

ACCOMPANIMENT CONTROL

START / STOP SYNC

FILL-IN A FILL-IN B

INTRO / ENDING

ACCOMPANIMENT CONTROL

START / STOP SYNC

FILL-IN A FILL-IN B

INTRO / ENDING

ACCOMPANIMENT CONTROL

START / STOP SYNC

FILL-IN A FILL-IN B

INTRO / ENDING

flash

The accompaniment section

Accompaniment operation

Accompaniment consists of Intro, normal, variation, fill (a-a, a-b, b-a, b-b), ending. Using different sections based on the structure of songs enables you to enhance musical performance.

INTRO

Press the [INTRO] button to insert an intro section before you start to play . The main section will be followed by the Intro section.

NORMAL and VARIATION

There are two main sections: normal and variation. It has its own two or four-measure section.

FILL

While the accompaniment is playing, you can fill in the rhythm/accompaniment by pressing the [FILL A] button or the [FILL B] button. This will automatically insert a fill section.

ENDING

When you press the [INTRO/ENDING] button, it brings rhythm accompaniment and your performance to the end.

Press the [ALBUM/SONG/STYLE] or direct style button.

Select a style. Select the desired style number with dial,[+/YES],[-/NO], or direct style buttons.

Start accompaniment. Start immediately Press the [START/STOP] button to start playing the rhythm without bass and chord accompaniment. Sync Start Press the [SYNC] button.The beat display will flash at the current tempo. To start the main section and accompaniment, play any key on the keyboard. (When A.B.C is On, play a key or chord in the auto accompaniment section of the keyboard).

Play the INTRO section This digital piano let you insert a short intro a rhythm pattern to make intro more smoother and more natural. Beats on LCD flash simultaneously in current tempo when pressing [SYNC] button. Press [INTRO/ENDING] button to insert INTRO. LCD lightens the intro flag. The INTRO plays automatically when the keyboard at the same time.

Page 17

Play the Main(A/B) section. Choose the desired style and press the [START/STOP] button. Press the [FILL A] button.The fill a-a or fill b-a will begin immediately and smoothly lead into the normal. LCD displays :"MAIN A".

Press the [FILL B] button.The fill a-b or fill b-b will begin immediately and smoothly lead into the VARIATION. LCD displays:"MAIN B".

Play the ENGING section To play the ENDING section, press [INTRO/ENDING]. LCD display :"ENDING".

FILL-IN A

FILL-IN B

INTRO / ENDING

NOTE:

If holding down the [FILL A] or [FILL B] button, the keyboard will play the fill section all along.

If pressing the [FILL A] or [FILL B] button at the last beat of the current measure, the fill will begin from the first beat of the next measure.

Stop playing the style.

The accompaniment can be stopped at any time by pressing the [START/STOP] button.

Press the [INTRO/ENDING] button if you want to go to the ending section and then stop. The ending section will begin from the top of the next measure.

SYNC STOP press the [SYNC] button to stop playing, and the synchronized start mode has been selected.

ACCOMPANIMENT CONTROL

START / STOP SYNC

FILL-IN A FILL-IN B

INTRO / ENDING

ACCOMPANIMENT CONTROL

START / STOP SYNC

FILL-IN A FILL-IN B

INTRO / ENDING

ACCOMPANIMENT CONTROL

START / STOP SYNC

FILL-IN A FILL-IN B

INTRO / ENDING

Page 18

Chord Recognize

Press the [A.B.C/MELODY OFF] button to turn on the A.B.C. mode. The A.B.C icon will appear next to "A.B.C" on the LCD.

In this mode, play the chords the chord section below the split point.

You can change the chords of the accompaniment by playing keys in the auto accompaniment section of the keyboard using either the "Single Finger" or "Fingered" method.

A.B.C/

MELODY OFF

Single Finger detect

C Cm

C7 Cm7

Major[M] Minor[m]

Seventh[7] Minor Seventh[m7]

Choose the desired style.(See appendix 2) Press the [START/STOP] button to start to play back the style. Play the chords by following the Single Finger Chord table.

The examples of Single Finger Chord C, Cm, C7 and Cm7 are shown as follows: C Major [M]:To play a major chord: Press the root note of the chord. Cm Minor[m]:To play a minor chord: press the root note together with any black key to the left of it. C7:To play a seventh chord: Press the root note together with any white key to the left of it. Cm7:To play a minor seventh chord: Press the note together with any white and black keys to the left of it. (Three keys altogether.)

Fingered detect

Play the Fingered Chord on the keys below the Spilt point. Choose your desired style. Press the [START/STOP] button to start to playback the style. Play the desired chords by following the Chord Chart (See appendix 6).

A total of 32 chords are provided as well as follows:

NOTE:

When A.B.C is ON, press the keys on the left of the split point. The chord will be recognized as fingered chords.

Cmadd9

C C

Cm9

Cm11 Cm

Madd9 M9 M7

Page 19

Volume Control

Accomp volume control

Accomp track adjust

Keyboard volume

To adjust accomp volume control, please [MIXER] button. LCD displays :"100 Accomp V".

You can adjust the volume values of ACCOMP with dial, [+/YES], [-/NO]. Parameter range: 000-127.

Press [+] and [-] at the same time will set the ACCOMP volume to 0. LCD displays:" OFF ACCOMP". Press them again to resume the original ACCOMP volume.

TRACK CHANNEL PARAMETER DEFAUL T

ACCOMP CH1, CH3, CH5,

CH7, CH10

0 127

109

CHORD 1 CH1

0 127

CHORD 2 CH3

0 127

CHORD 3 CH5

0 127

7392

DRUM CH10

0 127

BASS CH7

0 127

MIXER

/ NO

/ YES

FUNCTION-

/BACK

FUNCTION-

/BACK

FUNCTION+

/NEXT

FUNCTION+

/NEXT

TEMPO

This digital piano has 3 keyboard tracks: VOICE 1, VOICE 2, LOWER.

Track

Channel

Parameter Range

Default

VOICE 1

CH12

0 127

110

VOICE 2

CH13

0 127

LOWER

CH14

0 127

How to adjust:

Press the [MIXER] button. LCD displays:"100 ACCOMP V".

Press the [FUNCTION+/NEXT] or [FUNCTION-/BACK] button to select track that you want to adjust. Order: VOICE 1, VOICE 2,LOWER.

If you adjust the track voice 1, LCD displays:"112 VOICE1".

You can adjust the volume values of voice1 with dial, [+/YES],[-/NO].Parameter range :000-127.

Press [+] and [-] at the same time will set the volume voice1 to 0. LCD displays OFF VOICE 1; Press [+] and [-] simultaneously again to resume the original ACCOMP volume.

The volume adjustment of other track is the same as the track:Voice 1

Press the [MIXER] button to exit this mixer menu.

There are 5 accompaniment tracks for you to adjust: CHORD 1, CHOARD 2, CHORD 3, BASS and BASS DRUM.

Select a style to adjust track volume.

Press [MIXER] button. LCD displays:"100 ACCOMP V".

Press the [FUNCTION+/NEXT] or the [FUNCTION-/ BACK] button to select the track that you want to adjust.

You can adjust the accomp track volume values with dial, [+/YES], [-/NO]. Parameter range: 000-127. For example, CHORD1. LCD displays: "094 CHORD1 V".

Press [+] and [-] at the same time will set the accomp track volume to 0. LCD displays:"OFF CHORD1 V". Press them again to resume the original volume.

Press [MIXER] button to exit the mixer menu.

Page 20

Tempo

Metronome

One Touch Setting

Press the [TEMPO+] or [TEMPO-] button. The tempo value will be flashing. At that time, the tempo can be adjusted in the range of 30-280.

Hold down the [TEMPO+] or [TEMPO-] button and adjust the tempo continuously.

Press [TEMPO+] and [TEMPO-] simultaneously to set the tempo value back to the default one.

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

NOTE:

When the style stops while select the style, the tempo will change with the style automatically to the default tempo. When style is playing, the tempo will not change with the style.

The time signature changes automatically as soon as a style is selected.

In the FUNCTION menu, you can adjust the beat with dial,[+/YES],[-/NO].The range 0,2~9.(SEE FUNCTION OPERATION).

Press the [METRONOME] key to turn on the metronome and the metronome sound will be played .

Press the [METRONOME] key again to turn it off.

METRONOME

One Touch Setting is powerful and convenient Style mode function that let you instantly reconfigure virtually all setting of the instrument. You can save the following setting. Voice R1 number and volume Dual function. Voice R2 number and volume REVERB and CHORUS type and level OCTAVE

How to recall a one touch setting

Select a style.

Each style has four desired settings.

Press the [O.T.S] button. LCD displays O.T.S and turns A.B.C ON automatically. Press the [M1~M4] button. LCD displays O.T.S 1~4. corresponding to the desired setting.

O.T.S.

ONE TOUCH CONTROL

M 1 M 2

M 3

M 4

M 5 M 6

Page 21

When the style is playing, press [O.T.S] to turn on the O.T.S mode to inset a "Fill in " automatically. To insert "FILL A-A'',"FILL A-B'',"FILL B-A'' or "FILL B-B" ,please press memory number.

NOTE:

Press [O.T.S] key again to turn O.T.S mode off. LCD displays MEMORY.

O.T.S.

Memory

Demonstration

Memory feature can be used to memorize 48 complete control-panel setups (8 banks, 6 setups each) that you can recall whenever needed.

Data stored by the Memory

Voice R1, Voice R2, Voice L, Sustain, Style, Tempo, Function parameter, Mixer parameter, ACCOMP volume, ABC ON/OFF.

Select a Memory

Press the [BANK] button. LCD displays:" 001 MEM BANK". Press the [M1] to [M6] button. LCD displays 1-1 to 1-6. Select the desired memory bank with dial,[+/YES], [-/NO],or [BANK].

STORE MEMORY

Holding down the [STORE] button and pressing the [M1] to [M6] button simultaneously to store your desired memory.

RECALL YOUR MEMORY

First select your desired memory bank, and press any of the [M1] to [M6] button, then you can recall your desired memory.

BANK

STORE

ONE TOUCH CONTROL

M 1 M 2

M 3

M 4

M 5 M 6

Press the [DEMO] button to the DEMO mode. This digital piano plays all demos by turns from 001demo.

If you hold down [DEMO] for three seconds, it will play the current demo circularly.

Use the [MASTER VOLUME] to adjust the volume of DEMO.

Press the [TEMPO+] or [TEMPO-] button to adjust the tempo of the DEMO.

DEMO

Page 22

There are 8 demos at all. You can select the demo number with dial,[+/YES],[-/NO].

Press the [DEMO] or [START/STOP] button to exit from demo mode.

DEMO

START / STOP

Album

Song

NOTE:

All function keys on the panel are void.

Press [ALBUM/SONG/STYLE] button to the album mode. LCD displays the name and the number of the current album.

There are 100 albums at all. You can select the album number with dial,[+/YES],[-/NO].

Album parameters: accomp volume, tempo , voice, octave, DSP, normal or variation, dual ,etc.

These above parameters can be adjusted, but cannot be saved in this album.

Press the [TEMPO+] or [TEMPO-] button to adjust the tempo of the album. If you press the [TEMPO+] and [TEMPO-] button at the same time, you can adjust the tempo to the default tempo.

ALBUM / SONG

STYLE

ALBUM / SONG

STYLE

A.B.C/

MELODY OFF

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

Press the [STYLE/ALBUM/SONG] button to enter the SONG mode. This digital piano plays 60 songs circularly.

Use the [MASTER VOLUME] to adjust the volume of the SONG.

Press the [TEMPO+] or [TEMPO-] button to adjust the tempo of the SONG.

There are 60 songs at all. You can select the song number with dial,[+/YES],[-/NO].

Press the [SONG] or [START/STOP] button to stop playing this song.

Press the [START/STOP] button again to play current song circularly.

Press the [A.B.C/MELODY OFF] button to enter the lesson mode. The melody is mute. You can play the note shown on the LCD display.

There is a Intro and measure hint at the beginning of the song, which is easy for your learning.

Page 23

Function

Press the [FUNCTION+/NEXT] or [FUNCTION-/BACK] button to enter or exit the menu of function.

Transpose

Tune

Octave

Beat

Touch

Press the [FUNCTION+/NEXT] button to adjust transpose parameter with dial,[+/YES],[-/NO].

Parameter Range:-12 to +12 semitones.

FUNCTION-

/BACK

FUNCTION-

/BACK

FUNCTION-

/BACK

FUNCTION+

/NEXT

FUNCTION+

/NEXT

FUNCTION+

/NEXT

TEMPO

NOTE:

X'pose 1: Adjust the transpose parameter of voice R1; X'pose 2: Adjust the transpose parameter of voice R2, X'pose L: Adjust the transpose parameter of voice L.

You can change the OCTAVE and TRANSPOSE parameters of VOICER1, VOICER2, VOICE L separately and change the TUNE parameters of VOICE 1 only.

Press the button to adjust tune parameter with the dial,[+/YES],[-/NO].

Parameter Range:-50 to +50 cents.

[FUNCTION+/NEXT]

Press the [FUNCTION+/NEXT] button to adjust Octave parameter with dial,[+/YES],[-/NO].

Parameter Range:-2 to +2.

Press the [FUNCTION+/NEXT] button to adjust beat parameter with dial,[+/YES],[-/NO].

Parameter Range:0,2 to 9.

Press the [FUNCTION+/NEXT] button to adjust touch parameter with dial,[+/YES],[-/NO].

Parameter Range:from off to 3.

If you select the OFF,the touch sign will put out.

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

Page 24

Split point

Key select

Portamento time

PAD assign

Press the [FUNCTION+/NEXT] button to adjust split point parameter with dial,[+/YES],[-/NO] or press the corresponding key.

Parameter Range:from 1 to 76.

Press the [FUNCTION+/NEXT] button to adjust portamento time with dial,[+/YES],[-/NO].

Parameter Range:from 0 to 3.

Press the [FUNCTION+/NEXT] button to adjust PAD parameter with dial,[+/YES],[-/NO].

Parameter Range:from 1 to 5---Sustain,Soft,Accompst, Tempo tap,Memory.

The default pedal is the sustain pedal. All notes played on the keyboard will have a longer sustain by stepping the pedal.

If you select the soft pedal, all notes played on the keyboard will have a soft effect by stepping the pedal.

Press the [FUNCTION+/NEXT] button, you can select

portamento or modulation with dial,[+/YES],[-/NO].

If you select the modulation,the PORTAMENTO sign will put out.

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

/ NO

/ YES

NOTE:

This digital piano has another substantive soft pedal.

/ NO

/ YES

Page 25

DSP on/off

Reverb type

Reverb level

Chorus type

Chorus level

If you select the AccompSt pedal, it has the same function as press the [START/STOP] button by stepping the pedal.

If you select the TEMPOTAP pedal, you can quickly adjust the tempo of songs, demos, and styles, by stepping the pedal four times continuously,

If you select the MEMORY SELECT pedal, you can select each memory in turn by stepping the pedal. (from the MEMORY 01-1 to 08-4,all 32 memorys ).

Press the [FUNCTION+/NEXT] button to turn DSP on/ off with dial,[+/YES],[-/NO].

If you turn DSP off, the DSP sign will put out.

Press the [FUNCTION+/NEXT] button to adjust reverb type parameter with dial,[+/YES],[-/NO].

Parameter Range:from 0 to 7.

Press the [FUNCTION+/NEXT] button to adjust reverb level parameter with dial,[+/YES],[-/NO].

Parameter Range:from 0 to 127.

Press the [FUNCTION+/NEXT] button to adjust chorus type parameter with dial,[+/YES],[-/NO].

Parameter Range:from 0 to 7.

Press the [FUNCTION+/NEXT] button to adjust chorus level parameter with dial,[+/YES],[-/NO].

Parameter Range:from 0 to 127.

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

Page 26

Local on/off

Receive channel

Transmit channel

Default parameters

Press the [FUNCTION+/NEXT] button to turn local on/ off with dial,[+/YES],[-/NO].

Press the [FUNCTION+/NEXT] button to adjust receive channel with dial,[+/YES],[-/NO].

Parameter Range: 1 16 ALL.

If you select All , the instrument can receive midi message from all (1-16) midi channel.

Press the [FUNCTION+/NEXT] button to adjust transmit channel with dial,[+/YES],[-/NO].

Parameter Range: 1-16.

Only select one channel to transmit the midi message each time.

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

Press the [+] and [-] button simultaneously to set the parameter to its default value. For example:

PARAMETER RANGE DEFAULT

XPOSE -12~12 0

TUNE -50~50 0

OCTA VE -2~2 0

BEAT 0,2~9 4

TOUCH OFF-1~3 2

SPLITPT 1-76 27

PB RANGE 0~12 2

KEY SELECT PORTAMNETO/MODULATION PORTAMENTO

PORT AMEN 0~3 2

PEDAL SUS PEDALSUS,SOF,ACC,TAP,MEM PEDALSUS

DSP TYPE ON/OFF ON

REV .TYPE 0~7 4

REV.LEVL 0~127 40

CHO.TYPE 0~7 2

CHO.LEVL 0~127 0

LOCAL ON/OFF ON

RECEIVE 1~16-ALL ALL

TRANSMIT 1-16 1

Page 27

Disk

Using floppy disks

List Song Names of Disk

Insert the floppy disk that containing standard midi file into the disk drive, and then press the [DISK] button, "Wait "will display and the disk icon will flash on the LCD during loading disk song names. A song name of disk and disk icon is appeared on the LCD display. Only the names which extension is .MID in disk will be displayed and maximum value is 8. For example, the midi file is SONG1.MID. The LCD displays SONG1. Press the [YES/+],[NO/-], dial to select the song of disk that you want to playback. If there is no disk in the disk drive,"No Disk" appears on the LCD after pressing [DISK]button.

Playback Disk Song

It will begin or stop playing back the disk song after you pressed the [START/STOP]button You can choose another disk song while a midi song is playing by pressing the dial and [YES/+]/[NO/-] button . The playing song will be stopped as soon as the number of song is changed. If the song's number you selected have loaded, the song name will appear and it will start to play at once. Otherwise the "Wait " will display until the midi file to be loaded.

DISK

START / STOP

/ NO

/ YES

NOTE:

Flashing disk icon indicates the song data is loading or writing. Do not take out the floppy disk from disk drive while disk icon is flashing. The disk icon will stop flashing and lighting after having loaded. There is enough memory to store the disk song data in the piano. Playing any of the disk song will load nothing if all disk songs' data have been loaded. "No Disk" will appear on the LCD when taking out floppy disk from disk drive in disk mode. It is suggested that users should insert a disk into disk drive while playing the unit.

If no floppy disk in disk drive, the LCD will display "No Disk".

If the floppy disk is empty or there is no file which extension is .mid, the LCD will display "No File" .

If loading disk is error, the LCD will display "Disk Err".

Page 28

If the track number of a playing song is more than 64, the LCD will display:"Track Err".

If the midi format of a playing song is not format0 or format1 the LCD will display :"Format Err".

If the ticks in one beat of a playing song is more than 1024 or less than 24, the LCD displays :"Midi Err".

If midi data is irregular, the LCD will display :"Midi Err" or "Track Err".

Disk utility

Press the [UTILITY] button, the "Play Mode","Format" and "Delete" functions will be selected by [+] [-] button and data dial. If you want to enter these disk functions, you can press the [FUNCTION+/NEXT] button. To exit, press the [BACK] button..

Play mode

Press [UTILITY] button, the LCD will display:

Press [FUNCTION+/NEXT] button to enter PlayMode "Loop One" appearing on the LCD, indicating the disk songs will playback repeatedly.

Press [+] button or data dial. The "Loop All" indicating the disk songs will playback from the first songs to the end and then return to start first song again. Press [-] button or data dial will appear Loop One .

UTILITY

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

You can still receive MIDI data through the MIDI IN connector when the disk song is playing, but it may cause unexpected errors .We suggest you do not playback disk songs and receive MIDI data simultaneously.

NOTE:

/ NO

/ YES

Page 29

Disk format

Delete midi

UTILITY

Press [UTILITY] button and then press [+] button or rotate data dial LCD will display: "U2:Format".

Press [FUNCTION+/NEXT] button."FORMAT "will appear on the display.

Press [+] button to execute the format operation (or

press [-] button to cancel )."Wait...."will appear and

disk icon will flash on the display when format is in process.

When the disk has been formatted "FormatOK" will display on the LCD.

Select the disk midi deletion function by pressing the [UTILITY] and [+] button or rotating data dial,"DelMid" will appear on the display.

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

/ NO

/ YES

/ NO

/ YES

There is no action if you press any buttons when the disk is formatting. When a write-protected disk is loading,"Protect!" will be displayed.

NOTE:

Press [FUNCTION+/NEXT] button and the disk song name(.midi) will display.

Press [+] button or data dial to select the song you want to delete.

Page 30

Delete memory

Load midi

Press [NEXT] button and LCD will display:"Delete ?"

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

If you are sure, press [+] button and "Wait ."will appear on the LCD. If you do not want to delete the song, press [-] button .

Return to step 2 after the step above.

Select the disk memory deletion function by pressing the [UTILITY] and [+] button or rotating data dial. "Del Memo" will appear on the display.

Press [FUNCTION+/NEXT] button and the disk memory name(.mem) will display.

Press [+] button or data dial to select the memory you want to delete.

Press [FUNCTION+/NEXT] button and LCD will display Delete ?

If you are sure,you can press [+] button and "Wait ." will appear on the LCD. If you do not want to delete the song,you can press [-] button .

Return to step 2 after the step above.

UTILITY

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

Select the load disk midi function by pressing the [UTILITY] and [+] button or rotating data dial "LoadRec" will appear on the display.

Press [FUNCTION+/NEXT] button and the saved disk mid name (*.mid) will display.

Press [+] button or data dial to select the mid you want to load.

Press [FUNCTION+/NEXT] button and LCD will display "Wait " LCD will display as below when the MIDI song is loading at the end.

Page 31

Load mid function is only used for the midi files that be saved by the piano. If the midi files saved from PC or other midi devices, their names will not display on LCD and this function will be no effect. If you modify the midi file with PC, the midi file will not display in this function. If data is error, LCD will display "ERRORREC". If you have loaded a midi file by this function, the recorded memory data will be overwritten. You can continue to edit recorded data by record.

This function is only used for the memory files that saved by the piano. If not, LCD will display "ERRORMEM".

NOTE:

Select the load disk memory function by pressing the [UTILITY] and [+] button or rotating data dial. "LoadMem" will appear on the display.

Press [FUNCTION+/NEXT] button and the disk memory name(.mem) will display.

Press [+] button or data dial to select the mem you want to load.

Press [NEXT] button and LCD will display"Wait ".LCD will display as below if the memo is loading at the end .

Load memory

Save midi

UTILITY

SAVE

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

Disk save

Press [SAVE] button to select Disk Save mid job.

Press [FUNCTION+/NEXT] button to enter save midi file mode.

"MIDI0001" will appear on the LCD and the character "0" will flash to be changed by keyboard

You can press some special keyboards to remove the "flash" character to rename or delete it.

A standard midi format file will be saved in the disk. The file is always located in the root of disk. This midi file can be continued to edit by MIDI function.

Page 32

Input file name: If you want to enter a new name for the saved song, you can press the [ ] keyboard or[ ] keyboard to move the position of character you want to modify and then press the other special keyboard to name the song. A song name can consist of up to 8 characters.

Press [FUNCTION+/NEXT] button after entering new song name to confirm. The OverWri will appear on the LCD when there is a same song name in the disk. Press [FUNCTION-/BACK] or [-] button to rename . Press [+] button to overwrite the original file.

The "DISK FUL" will appear on the LCD if there is no more space in the disk.

The LCD will display :"Protect! " if a write-protected disk is load. Press number button or [+]/[-]/[FUNCTION-/BACK] button to return renaming song.

NOTE:

Save memory

Press [SAVE] and [+] button to select Save memory file function.

Press [FUNCTION+/NEXT] button to enter save memory file mode. LCD will display memory name.

SAVE

FUNCTION-

/BACK

FUNCTION+

/NEXT

TEMPO TEMPO

If you want to enter a new name for the new mem file, press the [ ] keyboard or [ ] keyboard to move the position of character you want to modify and then press the other special keyboard to name of mem. A mem name can consist of up to 8 characters.

Press [FUNCTION+/NEXT] button after entering new song name if you confirm. The "OverWri " will appear on the LCD when there is a same song name in the disk. Press [FUNCTION-/BACK] or [-] button to rename . Press [+] button to overwrite the original file.

Record

Start recording

There is one user song can be recorded in the piano. Each song has 5 tracks (1 ACCOMP track, 4 MELODY tracks). You can record the user song and save them into disk with the standard MIDI format.

RECORD

Press [RECORD] button. The REC flag will appear on the LCD and enter real time recording mode. The 4 beats will flash simultaneity on the LCD, indicating that it is ready for record.

Page 33

Playback recording

A melody track will be selected automatically after entering recording mode. You can also press melody track buttons to select other track for recording.

The recording will start as soon as you play a note on the keyboard or press [START/STOP] button. The TEMPO data will display with current TEMPO value and beat will appear on the LCD.

If a track is started to record, the data recorded before in this track will be deleted and over written by new record data.

If record starts, the parameter of TUNE will be reset automatically. You can turn on the metronome but the click is not recorded in user song when recording is in process.

Press [START/STOP] button to play or stop the STYLE. It will not exit record mode when the piano is recording.

Press [DEMO] button to stop recording.Demo song plays at once.The record will not lose.

ONE TOUCH CONTROL

M 1 M 2

M 3

M 4

M 5 M 6

ONE TOUCH CONTROL

M 1 M 2

M 3

M 4

START / STOP

DEMO

Select track

Press the [M1]--[M4]/[ACCOMP/CLEAR] button to select a record track. A lighting flag of the track indicates that the relative track is turned on. You can not light the flag of the track that there is not any record data.

Playback

Press [PLAY/STOP] button to start playing the tracks after you have selected it.

If the USER SONG is empty or no tracks are selected, the LCD will display :"NoRecord".

Stop playback

Press [PLAY/STOP] button to stop playing when a user song is playing

PLAY/STOP

The recorded data will be clear after power on or reset.

NOTE:

Page 34

MIDI

What is MIDI

MIDI connection

MIDI application

Musical Instrument Digital Interface. The standard interface between PC and Electronic instrument.

It is equipped with standard MIDI interface, including 1 MIDI IN and 1 MIDI OUT.

Connection It can connect with PC or other MIDI equipment.

Connection rule

In midi connection, the equipment which controls another equipment is called Host equipment , while anotheris called affiliated equipment . The host equipment's MIDI OUT connect with affiliated equipment's MIDI IN. Do not connect MIDI OUT with MIDI IN on the same equipment.

The method of connection

A.Connect the MIDI interface with PC.

B.Connect the MIDI interface with the other MIDI interface.

The keyboard controls other equipment or electronic instrument.

Other equipments control it. (See MIDI CHART for details of MIDI information on P.39)

PC can record the play on it.

A B

Page 35

Specifications

Keyboard Voice Style Demo Song Album Max, Polyphony Display Switch and Buttons

Accompaniment Control

Record function Sequencer

Panel Memory

MIDI Connectors Speaker

Dimension Weight

88 Graded Hammer keys,3 kinds of touch level.

142 Voices 100 Styles 8 Demos and 60 Songs and 100 albums 64-note Polyphony (max) Multi functional LCD display with blue backlit POWER SWITCH, VOLUME,ALBUM/SONG/STYLE,DUAL, O.T.S, DEMO, TOUCH, DIAL, TEMPO,ACCOMP VOLUME,NUMERIC KEYPAD, SPLIT/LOW VOICE, METRONOME, BANK,STORE, MEMORY 1-6,PIANO,FUNCTION +/NEXT,FUNCTION-/BACK, MIXER,SUSTAIN,TOUCH,DSP,PORTAMENTO/MODULATION, A.B.C/MELODY OFF,DISK,SAVE,UTILITY

START/STOP, SYNC, INTRO/ENDING, FILL-IN A, FILL-IN B

RECORD,PLAY/STOP 4 Melody tracks and 1accompaniment track

ACCOMP/CLEAR, MELODY 1-4

48 Memory Storage TRANSMIT, RECEIVE, 16 MIDI TERMINALS

AC POWER, HEADPHONES, AUX.OUT, MIDI IN/OUT,

3 PEDALS

8 25w x 2

1380 x 520 x 830MM

62kg

Page 36

Appendix 1-Voice List

Santur

Jazz

Classic

Page 37

Page 38

01 The Fusion

02 The Ballad

03 Pop

04 Latin

05 The Jazz

06 Pop Rock

07 My Motherland

08 Jasmine

Appendix 3-Demo List

Appendix 4-Song List

Concerto for Violin and Orchestra in a Minor Nocturne Symphone No.94 Suprise

Page 39

NO NO NO

ALBUM ALBUM ALBUM

FAVORITE

001 Easy Sunday

002 Moon Light

003 Love Me Or Not

004 Someone For Me

005 Sitting D own Here

006 Don t Break My Heart

007 Donot Say Love Me

008 Saving All My Love For You

009 Wish You Safe

010 Beauty And The Beast

011 Quiet- Here W ith You

012 Only You

013 The Girl Opposite Look Here

014 Dave Again

015 Go Home

016 Only Love

017 Funky Disco

018 Corazon Espioade

019 When The Saints Go Marching In

020 Funky Pieces

021 Bath Song

BALLROOM

022 Aura Lee

023 Unchained Melody

024 American Patrol

025 Georgia On My Mind

026 When You Hold Me You Love Me

027 Appointment in 98

028 Im Mai

029 Old Folks At Home

030 Rising Sun

031 Curfew

ROCK

032 Serbian Barber

033 Turkey In The Straw

034 Ring The B anjo

035 Die Lorelei

036 Who Can Tell Me

037 Funiculi - Funicula

038 Snowing Street

FUNK&SOUL

039 Down By The Riverside

040 Billy Bailey

041 Greensleeves

042 The Cuckoo

043

DANCE&POP

044 Dry Sky Thunder

045 The Boy Reading

046 In The Rain

047 London Bridge

048 Little Star Partita

049 Strlight On The Rail

050 Battle Hymn Of

051 Pop Goes The Weasel

052 Galloper

053 Spain Dance

054 Ten Little Indias

JAZZ&SWING

055 Path

056 Duckling

057 Silent Night

058 Yankee Doodle

059 Chopsticks

060

Hungarian Dance Of Gypsia Style

061 Aloha Oe

062 Twinkle Twinkle Little Star

063 Jingle Bells

064 Night at suburb of Moscow

065 Home Sweet Home

066 Grandfather

067 Washing Song

068 Cuerchack Dance

069 Colt Pace

070 Samba Dance

071 Attractive Lagtime Dance

072 ve been working on the railroad

073 The Cup Of

074 Happy Birthday To You

075 O Du Lieber Augustin

076 Waltz Of The King

077 Dance Of The Crown 078

Beer Tub Boercar

The Republic

s Clock

Live

079 The Happiness Of Bumper

080 Amusement

081 Tulip

082 Mary Had A Little Lamb

083 Mornin g Of Miaolin

DRUM&BASS

084 My Bonnie

085 I Want To Have A Home

086 Friend

087 Long Long Ago

088 Celebration

089

090 Loessial Tableland

TRADITIONAL

091 Flapping Tambourine And Sing

092 Raising Your Cover

093 A Girl From Altai

094 Meet At The Aobao

095 Guard The Border On Running Horse

096 Record Of The Journey To The West

097 Plait Corbeil

098 Jasmine

099 Higher Step By Step

100 Solo Riverside

Don't Let The Sun Go Down On Me

From The Magic Flute

Appendix 5-Album List

Page 40

Appendix 6-Chord Chart

Major[M]

Major sixth [6]

Major seventh [M7]

Major seventh sharp Eleventh [M7#11]

Major add ninth [Madd9]

Major ninth [M9]

Major sixth add ninth [6 9]

augmented [aug]

Minor [m]

Minor sixth [m6]

Minor seventh [m7]

Minor seventh flatted fifth [m7b5]

Minor add ninth [madd9]

Minor ninth [m9]

Minor eleventh [m11]

Minor major seventh [mM7]

Minor major ninth [mM9]

Diminished [dim]

Diminished seventh [dim7]

Seventh [7]

Seventh suspended Fourth [7sus4]

Seventh flatted Fifth [7b5]

Seventh Ninth [79]

Seventh sharp eleventh [7#11]

Seventh thirteen [7 13]

Seventh flatted Ninth [7b9]

Seventh flatted Thirteen [7b13]

Seventh sharp ninth [7#9]

Major Seventh augmented [M7aug]

Seventh augmented [7 aug]

Suspended Fourth [sus4]

One plus two plus five [1+2+5]

1-3-5

1-(3)-5-6

1-3-(5)-7

1-(2)-3-#4-(5)-7

1-2-3-5

1-2-3-(5)-7

1-2-3-(5)-6

1-3-#5

1-b3-5

1-b3-5-6

1-b3-(5)-b7

1-b3-b5-b7

1-2-b3-5

1-2-b3-(5)-b7

1-(2)-b3-4-5-(b7)

1-b3-(5)-7

1-2-b3-(5)-7

1-b3-b5

1-b3-b5-6

1-3-(5)-b7

1-4-5-b7

1-3-b5-b7

1-2-3-(5)-b7

1-2-3-#4-(5)-b7 or

1-(2)-3-#4-5-b7

1-b2-3-(5)-b7 or

2-3-5-6-b7

1-b2-3-(5)-b7

1-3-5-b6-b7

(1)-#2-3-(5)-b7

1-3-#5-7

(1)-3-#5-b7

1-4-5

1-2-5

CM7

CM7#11

Cmadd9

Cm9

C6 9

Caug

Cm6

Cm7

Cm7b5

Cmadd9

Cm9

Cm11

CmM7

CmM9

Cdim

Cdim7

C7sus4

C7b5

C7 9

C7#11

C7 13

C7b9

C7b13

C7#9

CM7aug

C7aug

Csus4

C1+2+5

CM7

CM7#11

Cm(9)

CM(9)

C6(9)

Caug

Cm6

Cm7

Cm7b5

Cm(9)

Cm7(9)

Cm7(11)

CmM7

CmM7(9)

Cdim

Cdim7

C7sus4

C7b5

C7(9)

C7(#11)

C7(13)

C7(b9)

C7(b13)

C7(#9)

CM7aug

C7aug

Csus4

Chord Name [Abbreviation] Normal Voicing Chord Display

Page 41

Appendix 7-MIDI Chart

Function

Transmitted

Recognized Remarks

Basic Default Channel Changed

1 ch

1 -16 ch

ALL

1-16 ch

Default

Mode Message

Altered

** *********

Note

Number : True voice

1-60/72-127

0 —127

Velocity : Note on

Note off

After key’s

Touch Ch’s

Pitch Bend

Control 0

120

121

123

Bank select Modulation Portamento time

Volume Pan Expression

Sustain Pedal

Sostenuto Pedal

Soft Pedal Reverb Program

Chorus Program

Reverb Level Chorus Level All sound off

Reset all controllers

All notes off

Program

Bank Select

Change : true

System Exclusive

System : Song Position

: Song Select

Common : Tune

System :

Clock

Real Time :

Commands

Aux :

LOCAL ON/OFF

: All notes

off Messages:Active sense

Mode 1: OMNI ON , POLY Mode 2 : OMNI ON , MONO : YES Mode 3: OMNI OFF , POLY Mode 4 : OMNI OFF , MONO : NO

36-96