Page 1
Watch your fingers when adjusting clamps. They may become pinched resulting in injury.
Be careful around pipe ends, inside the pipe and screw ends. Metal shavings, etc. May injure your fingers.
Before assembly, please make sure that all the items listed below are present.
ASSEMBLY INSTRUCTIONS
Caution !
Inside This Package
[10” DRUM PADS] BOX
ACCESSORY BOX
[14" CYMBAL PAD] BOX [12" CYMBAL PADS] BOX [HI-HAT PEDAL] BOX
L-Rods of Pads X 5
Drumsticks X 2
Cymbal Holder (Short)
Cymbal Holder (Long)
Boom Cymbal Arms X 2
Drum Key
AC Adapter
Instruction Manual
Connection Cables X 11
Pillar(L1)
Pillar(R1)
Pillar(L2) Pillar(R2)
Kick Pad
10” Drum Pad x 2
12" Cymbal Pads x 314" Cymbal Padx2
Hi-Hat Control Pedal
DRUM RACK
[DRUM MODULE] BOX
[Kick Trigger] BOX
Hexagon Key (M5)
Center Pipe(1)
Center Pipe(2)
Side Arm(L1)
Side Arm(R)
Side Arm(L2)
13
Side Arm(L2)
14
Tighten
the screw
Tighten th e screw
12
Pillar(L1)
11
10
Tighten th e screw
Pillar(R1)
Assembly
Side Arm( )
R
[8” DRUM PADS] BOX
8” Drum PadX2
8” Drum PadX1
[8” DRUM PAD] BOX
Owner’s Manual
Pillar(L1)
Center Pipe(1)
1
9
Tighten th e screw
Pillar(L2)
4
2
Center Pipe(2)
S
id
e Arm(L1)
Pillar(L1)
Pillar(R1)
Center Pipe(1)
3
3
Center Pipe(2)
5
Pillar(L2)
Side Arm(L1)
Side Arm(R)
7
Pillar(R2)
Assembly
1 Setting up the frame of the digital drum set
[1] Attach the Center Pipe(1) to the clamp on the pillar(L1)
[2] Attach the Center Pipe(2) to the clamp on the pillar(L1)
[3] Attach the Center Pipe(1)(2) to the clamp on the pillar(R1)
[4] Using the wing nut tighten the screws on the clamp.
[5] Attach the side arm (L1) to the clamp on the pillar(L2)
[6] Tighten the screws on the clamp.
[7] Attach the side arm (R) to the clamp on the pillar(R2)
[8] Tighten the screws on the clamp.
[9] Attach the side arm(L1) to the clamp on the pillar (L1)
[10] Tighten the screws on the clamp.
[11] Attach the side arm(R) to the clamp on the pillar(R1)
[12] Tighten the screws on the clamp.
[13] Attach the side arm(L2) to the clamp on the pillar(L1)
[14] Tighten the screws on the clamp.
Tighten th e screw
4
Tighten th e screw
Tighten th e screw
6
8
4
4
4
4
[ ] BOXKick Pad
Page 2
Loo sen the w ing scr ew on the c lamp
Ins ert the d rum mod ule to th e clamp
Tigh ten the w ing scr ew on the c lamp
Loo sen L-r od wing n uts on dr um pad cl amp.
Ins ert tex tured p lasti c end of L- rod int o tom cla mp and ti ghten w ing nut s.
Rep eat for e ach dru m pad cla mp.
Loo sen win g nut on pa d.
Att ach pad s to L-ro ds and ti ghten w ing nut s. Repe at for ea ch pad.
1
2
3
4
Attaching pads to rack
Attaching module
Attaching cymbals
Bass drum and Hi-Hat pedal
1
2
3
Place the kick pad on the floor in the center of rack.
Attach your kick pedal to the kick pad.
Place the hi-hat control pedal on the floor on your left side.
Please connect the clearly marked cables from the pads to the correct inputs on the drum module, and you are ready to play!
1
2
3
Insert each boom cymbal arm into pillar(L1) and pillar(R1).
Insert cymbal holder(short) on the left side-arm cymbal clamp.
Insert cymbal holder(long) on the right side-arm cymbal clamp.
Remove wing nut and felt washer from cymbal tilter.
Place cymbal pad on tilter assembly.
Re-attach the felt washer and wing nut. Tighten wing nut.
Note: Cymbals are arranged as follows: 12" Hi-Hat on left-side
short arm, 12" crash on left-side boom arm, 14" ride on right-side
boom arm, 14" crash2 on right-side long arm.
1
2
3
4
5
2
3
side a rm(L1 )
Inse rt the dr um modu le
Tigh ten the wi ng scre w
Loos en the wi ng scre w
1
12" Cymbal Pad
12" Cymbal Pad
Drum module
14" Cymbal Pad
10” Pad
Kick pad
Hi-Hat Control
Pedal
12” Cymbal Pad
10”
12"
12"
14"
12”
1
Win g Nut
Fel t Washer
3
Win g Nut
Fel t Washer
4
10”
8”
8”
8”
10” Pad
8” Pad 8” Pad
8” Pad
DD518DX_Setup_G02_120217
kick pedal
1
Loading...