Maytag MVWX600BW0, MVWX500BW0, 7MMVWH450DW0, WTW8500DW0, WTW8500DC0 Installation Guide
...
WASHER INSTALLATION INSTRUCTIONS
INSTRUCTIONS POUR UINSTALLATION DE LA LAVEUSE
Table of Contents Table des matibres
WASHER SAFETY ........................................................................ 1
iNSTALLATiON REQUIREMENTS ............................................... 2
Tools and Parts ..................................................................... 2
Location Requirements ....................................................... 2
Drain System ........................................................................ 3
Electrical Requirements ...................................................... 4
INSTALLATION iNSTRUCTiONS ................................................. 4
Before you start: remove shipping materials .................... 4
Connect Drain Hose ............................................................. 5
Connect inlet Hoses ............................................................. 6
Level Washer ........................................................................ 7
Complete installation Checklist .......................................... 8
TROUBLESHOOTING .................................................................. 9
Para obtener acceso al instrucciones de instalaci6n en espaSol, o para obtener informaci6n adicional
acerca de su producto, visite: www.whirlpool.com
iNSTALLATiON NOTES
Date of purchase:
Date of installation:
Installer:
Model number:
Serial number:
SLeCURITE DE LA LAVEUSE ..................................................... 11
EXIGENCES D'INSTALLATION ................................................. 11
Outillage et pibces ............................................................... 11
Exigences d'emplacement ................................................. 12
Systbme de vidange ............................................................. 12
Sp6cifications _lectriques ................................................... 13
iNSTRUCTiONS D'INSTALLATION ........................................... 14
Avant de commencer : retrait du mat6riel d'e×p6dition ... 14
Raccordement du tuyau de vidange ................................... 15
Raccordement des tuyau× d'arriv_e d'eau ........................ 16
Etablissement de I'aplomb de la laveuse ........................... 17
Liste de v_rification pour I'ach_vement de I'installation.. 18
DEPANNAGE .............................................................................. 19
NOTES SUR L'INSTALLATION
Date d'achat :
Date d'installation :
Installateur :
Num_ro de module :
Num_ro de s_rie :
WASHER SAFETY
Your safety and the safety of others are very important.
We have provided many important safety messages inthis manual and on your appliance. Always read and obey all safety
messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word "DANGER" or "WARNING."
These words mean:
You can be kifled or seriously injured if you don't immediately
follow instructions.
You can be killed or seriously injured if you don't follow
instructions.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
W10455762B
W10455774B=SP
INSTALLATION REQUIREMENTS
Tools and Parts
Gather required tools and parts before starting installation.
Tools needed:
@
Adjustable or open end
wrench 9/16" (14 mm)
4 ='rnirl
(102 mm)_
Level
ff
Wood block
Pliers that open to 13/4"
(44.5 mm)
Optional tools:
Flashlight
Parts supplied:
NOTE: All parts supplied for installation are in
cardboard insert in the top of the washer.
Ruler or measuring tape
Bucket
Parts needed: (Not supplied with washer)
Net hoses with
flat washers
To order, please refer to toll-free phone numbers on back page
of your Use and Care Guide.
[] 8212656RP 10 ft. (3.0 m) inlet hose, Black EPDM (2 pack)
[] 8212641RP 5 ft. (1.5 m) Net hose, Black EPDM (2 pack)
[] 8212646RP 4 ft. (1.2 m) Inlet hose, Black EPDM (2 pack)
[] 8212545RP 5 ft. (1.5 m) Inlet hose, Red and Blue EPDM
(2 pack)
[] 8212487RP 5 ft. (1.5 m) Nylon braided inlet hose (2 pack)
[] 8212638RP 6 ft. (1.8 m) Nylon braided inlet hose, space
saving 90° elbow, hypro-blue steel couplings
(2 pack)
[] 8212637RP 6 ft. (1.8 m) Net hose, Black EPDM, space
saving 90° elbow, hypro-blue steel couplings
(2 pack)
Alternate parts: (Not supplied with washer)
Your installation may require additional parts. To order, please
refer to toll-free numbers on back page of your Use and Care
Guide.
If you have:
Overhead sewer
1" (25 mm) standpipe
Drain hose too short Extension Drain Hose Part
Lint clogged drain
You will need:
Standard 20 gal. (76 L) 39" (990 mm)
tall drain tub or utility sink, sump
pump and connectors (available from
local plumbing suppliers)
2" (51 mm) diameter to 1" (25 mm)
diameter Standpipe Adapter
Part Number 3363920
Connector Kit Part Number 285835
Number 285863
Connector Kit Part Number 285835
Drain Protector Part Number 367031
Connector Kit Part Number 285835
Drain hose with clamp,
U-form, and cable tie
2
LOCATION REQUIREMENTS
Select proper location for your washer to improve performance
and minimize noise and possible "washer walk." install your
washer in a basement, laundry room, closet, or recessed area.
42"
(1067mm)
You will need:
[] A water heater set to 120° F (49° C).
[] A grounded electrical outlet located within 4 ft (1.2 m) of
power cord on back of washer.
[] Hot and cold water faucets located within 3 ft (0.9 m) of hot
and cold water fill valves on washer, and water pressure
of 20-100 psi (138-690 kPa).
[] A level floor with maximum slope of 1" (25 mm) under entire
washer. Installing on carpet is not recommended.
[] Floor must support washer's total weight (with water and load)
of 315 Ibs (143 kgs).
iMPORTANT: Do not install, store, or operate washer where it will
be exposed to weather or in temperatures below 32° F (0° C).
Water remaining in washer after use may cause damage in low
temperatures. See "Washer Care" in your Use and Care Guide
for winterizing information.
Proper installation is your responsibility.
Recessed area or closet installation
3 II
(76 ram)
i i
i i
i i
i i
i i
i
i i
i
i
14 =. max. ::
(356 ram)
48 in.2
(310 cm2)
DRAIN SYSTEM
Drain system can be installed using a floor drain, wall standpipe,
floor standpipe, or laundry tub. Select method you need.
Floor standpipe drain system
Minimum diameter for a standpipe drain: 2" (51 mm). Minimum
carry-away capacity: 17 gal. (64 L) per minute. Top of standpipe
must be at least 39" (990 mm) high; install no higher than 96"
(2.44 m) from bottom of washer. If you must install higher than
96" (2.44 m), you will need a sump pump system.
Wall standpipe drain system
"'-:
r _ ,q
24 in?
(155cm_)
I
,\jq
"O,q
125ram)
iiii
_" 1"
(25 ram)
176 ram)
511 I ill
(126 m , ,,,,
Dimensions show recommended spacing allowed, except for
closet door ventilation openings which are minimum required.
This washer has been tested for installation with spacing of 0"
(0 mm) clearance on the sides. Consider allowing more space
for ease of installation and servicing, and spacing for companion
appliances and clearances for walls, doors, and floor moldings.
Add spacing of 1" (25 mm) on all sides of washer to reduce
noise transfer. If a closet door or Iouvered door is installed,
top and bottom air openings in door are required.
See requirements for floor standpipe drain system.
Floor drain system
(
Floor drain system requires a Siphon Break Kit (Part Number
285834), 2 Connector Kits (Part Number 285835), and an
Extension Drain Hose (Part Number 285863) that may be
purchased separately. To order, please see toll-free phone
numbers in your Use and Care Guide. Minimum siphon break:
28" (710 mm) from bottom of washer. (Additional hoses may
be needed.)
Laundry tub drain system
Minimum capacity: 20 gal. (76 L). Top of laundry tub must be at
least 39" (990 mm) above floor; install no higher than 96" (2.44 m)
from bottom of washer.
IMPORTANT: To avoid siphoning, no more than 4.5" (114 mm)
of drain hose should be inside standpipe or below the top of
wash tub. Secure drain hose with cable tie.
ELECTRICAL REQUIREMENTS
INSTALLATION INSTRUCTIONS
Excessive Weight Hazard
Use two or more people to move and install washer.
Failure to do so can result in back or other injury.
Electrical Shock Hazard
Plug into a grounded 3 prong outlet.
Do not remove ground prong.
Do not use an adapter.
Do not use an extension cord.
Failure to follow these instructions can result in death,
fire, or electrical shock.
[] A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply
is required. A time-delay fuse or circuit breaker is recommended.
It is recommended that a separate circuit breaker serving only this
appliance be provided.
[] This washer is equipped with a power supply cord having
a 3 prong grounding plug.
[] To minimize possible shock hazard, the cord must be plugged
into a mating, 3 prong, grounding-type outlet, grounded in
accordance with local codes and ordinances. If a mating outlet
is not available, it is the personal responsibility and obligation
of the customer to have the properly grounded outlet installed
by a qualified electrician.
[] If codes permit and a separate ground wire is used, it is
recommended that a qualified electrician determine that
the ground path is adequate.
[] Do not ground to a gas pipe.
[] Check with a qualified electrician if you are not sure the
washer is properly grounded.
[] Do not have a fuse in the neutral or ground circuit.
Before you start: remove shipping materials
It is necessary to remove all shipping materials for proper
operation and to avoid excessive noise from washer.
, Move washer
Move washer to within 48" (1.2 m) of its final location; it must
be in a fully upright position.
NOTE: To avoid floor damage, set washer onto cardboard
before moving it and make sure lid is taped shut.
2, Remove shipping base
GROUNDING INSTRUCTIONS
For a grounded, cord-connected washer:
This washer must be grounded, in the event of a malfunction
or breakdown, grounding will reduce the risk of electrical
shock by providing a path of least resistance for electric
current. This washer is equipped with a cord having an
equipment-grounding conductor and a grounding plug.
The plug must be plugged into an appropriate outlet that is
properly installed and grounded in accordance with all local
codes and ordinances.
WARNING: improper connection of the equipment-
grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or serviceman if you are
in doubt as to whether the appliance is properly grounded.
Do not modify the plug provided with the appliance - if it will
not fit the outlet, have a proper outlet installed by a qualified
electrician.
For a permanently connected washer:
This washer must be connected to a grounded metal,
permanent wiring system, or an equipment grounding
conductor must be run with the circuit conductors and
connected to the equipment=grounding terminal or lead
on the appliance.
4
To avoid damaging floor, place cardboard supports from
shipping carton on floor behind washer. Tip washer back and
place on cardboard supports. Remove shipping base. Set
washer upright.
IMPORTANT: Removing shipping base is necessary for proper
operation. If your washer includes a sound shield, please refer
to the instructions included with the sound shield to install it at
this time.
Remove packing tray from tub
Remove tape from washer lid, open lid and remove cardboard
packing tray from tub. Be sure to remove all parts from tray.
NOTE: Keep tray in case you need to move washer later.
CONNECT DRAIN HOSE
Attach drain hose to drain port
Remove the red plastic plug from the black drain port on the
back of the washer.
If clamp is not already in place on elbow end of drain hose,
slide it over end as shown. Squeeze clamp with pliers and
slide black elbow end of drain hose onto black drain port
and secure with clamp.
For a laundry tub or standpipe drain, go to step 6.
For a floor drain, remove the preinstalled drain hose form as
shown in Step 7. You may need additional parts with separate
directions. See "Tools and Parts."
Firmly grasp power cord plug and pull to free from rear panel.
Gently place power cord over console to allow free access
to back of washer.
_6. Place drain hose in standpipe
Drain
Place hose into standpipe (shown in picture) or over side
of laundry tub.
IMPORTANT: 4.5" (114 mm) of drain hose should be inside
standpipe; do not force excess hose into standpipe or lay
on bottom of laundry tub. Drain hose form must be used.
(floor drain installations only)
I
For floor drain installations, you will need to remove the drain
hose form from the end of the drain hose. You may need
additional parts with separate directions. See "Tools and Parts."
Clear water lines
Run water for a few seconds through hoses into a laundry tub,
drainpipe, or bucket to avoid clogs. Water should run until clear.
Make note of which hose is connected to hot water to help in
attaching hoses to washer correctly.
CONNECT INLET HOSES
Washer must be connected to water faucets with new inlet
hoses with flat washers (not provided). Do not use old hoses.
NOTE: Both hoses must be attached and have water flowing
to inlet valves. If you are only connecting to a cold water
faucet, you must use a Y-adapter (not provided).
8, Connect inlet hoses to water faucets
Attach hose to hot water faucet. Screw on coupling by hand
until it is seated on washer. Use pliers to tighten couplings an
additional two-thirds turn. Repeat this step with second hose
for cold water faucet.
IMPORTANT: Do not overtighten or use tape or sealants on
valve when attaching to faucets or washer. Damage can result.
O, Connect inlet hoses to washer
Attach hot water hose to hot water inlet valve marked with a
red ring. Screw coupling by hand until it is snug. Use pliers to
tighten couplings an additional two-thirds turn. Repeat with
cold water inlet valve.
IMPORTANT: To reduce risk of hose failure, replace the hoses
every 5 years. Record hose installation or replacement dates
for future reference.
[] Periodically inspect and replace hoses if bulges, kinks, cuts,
wear, or leaks are found.
fl "1. Check for leaks
C
Turn on water faucets to check for leaks. A small amount of
water may enter washer. It will drain later.
6
Loading...