Maytag MVWB850YW, MVWB850YG, MVWB750YW, MVWB950YG, MVWB950YW Dimension Guide

PRODUCT MODEL NUMBERS

MVWB750Y, MVWB800Y,
MVWB850Y, MVWB950Y

Washer Dimensions:

Top Loading Washer

157⁄8"*

(403 mm)

1"

(25 mm)

* Required spacing

14"* max.

27 1/2"

(699 mm)

1"

(25 mm)

1"

(25 mm)

(356 mm)

27"

(686 mm)

(127 mm)

48 in.2*

(310 cm2)

24 in.2*

(155 cm2)

5"*

Front view Side view Closet door

with vents

Spacing for recessed area or closet installation

All dimensions show recommended spacing allowed, with tested
spacing of 0" (0 mm) clearance on sides.

■ Additional spacing should be considered for ease of

installation and servicing.

■ Additional clearances might be required for wall, door, and

oor moldings.

■ Additional spacing should be considered on all sides of the

washer to reduce noise transfer.

■ For closet installation, with a door, minimum ventilation

openings in the top and bottom of the door are required.
Louvered doors with equivalent ventilation openings are
acceptable.

■ Companion appliance spacing should also be considered.

3"*

(76 mm)

3"*

(76 mm)

W10410358A

ELECTRICAL REQUIREMENTS

41/2"

(114 mm)

A 120 volt, 60 Hz., AC only, 15- or 20-amp, fused electrical supply is required. A time-delay fuse or circuit breaker is recommended. It is
recommended that a separate circuit serving only this appliance be provided.

DRAIN SYSTEM

Drain system can be installed using a oor drain, wall standpipe, oor standpipe, or laundry tub. Select method you need.

Floor standpipe drain system

39"

41/2"

(114 mm)

(990 mm)

Minimum diameter for a standpipe drain: 2" (51 mm). Minimum
carry-away capacity: 17 gal. (64 L) per minute. Top of standpipe
must be at least 39" (990 mm) high; install no higher than 96"
(2.4 m) from bottom of washer. If you must install higher than 96"
(2.4 m), you will need a sump pump system.

Wall standpipe drain system

41/2"

(114 mm)

See requirements for oor standpipe drain system.

Floor drain system

Floor drain system requires a Siphon Break Kit (Part Number

285834), 2 Connector Kits (Part Number 285835), and an
Extension Drain Hose (Part Number 285863) that may be
purchased separately. To order, please see toll-free phone
numbers in your “Use and Care Guide.” Minimum siphon break:
28" (710 mm) from bottom of washer. (Additional hoses may
be needed.)

Laundry tub drain system

30"

39"

(762 mm)

(990 mm)

Minimum capacity: 20 gal. (76 L). Top of laundry tub must be at
least 39" (990 mm) above oor; install no higher than 96" (2.4 m)
from bottom of washer.

IMPORTANT: To avoid siphoning, no more than 41⁄2" (114 mm)
of drain hose should be inside standpipe or below the top of
wash tub. Secure drain hose with cable tie.

Because Whirlpool Corporation policy includes a continuous commitment to improve Dimensions are for planning purposes only. For complete details, see Installation
our products, we reserve the right to change materials and specications without notice. Instructions packed with product. Specications subject to change without notice.

W10410358A

11/2011