Maytag MED5591TQ1 User Manual [en, es, fr]

JVXAYKVG

29" (73.7 CM) LONG VENT ELECTRIC DRYER

USE & CARE GUIDE

SECADORA ELÉCTRICA CON DUCTO DE ESCAPE

DE 29" (73,7 CM)

MANUAL DE USO Y CUIDADO

SÉCHEUSE ÉLECTRIQUE AVEC CONDUIT D'ÉVACUATION

DE 29" (73,7 CM)

GUIDE D'UTILISATION ET D'ENTRETIEN

FOR QUESTIONS ABOUT FEATURES, OPERATION/PEREORMANCE,

PARTS, ACCESSORIES OR SERVICE CALL: 1,800,688,9900

IN CANADA, CALL: 1,800,807,6777

VISIT OUR WEBSITE AT WWW,MAYTAG.COM

IN CANADA, WWW,MAYTAG,CA

W10088776A

SI TIENE PREGUNTAS RESPECTO A LAS CARACTERISTICAS,

FUNCIONAMIENTO, RENDIMIENTO, PARTES, ACCESORIOS O

SERVICIO TÉCNICO, LLAME AL: 1.800,688,9900

EN CANADÁ, LLAME AL: 1.800.807.6777

VISITE NUESTRO SITIO WEB EN

WWW.MAYTAG.COM

EN CANADÁ,

WWW.MAYTAG.CA

AU CANADA, POUR ASSISTANCE, INSTALLATION OU SERVICE,

COMPOSER LE : 1,800.807.6777

OU VISITER NOTRE SITE INTERNET A

WWW.MAYTAG.CA

TABLE OF CONTENTS

DRYER SAFETY...................................................................3

INSTALLATION INSTRUCTIONS

Tools and Parts..................................................................4

Location Requirennents.....................................................4

Electrical Requirements - U.S.A. Only Electrical Requirements - Canada Only

Electrical Connection - U.S.A. Only...................................8

Venting Requirements

Plan Vent System...........................................................1 5

Install Vent System.........................................................1 7

Install Leveling Legs........................................................17

Connect Vent...................................................................17

Level Dryer

Reverse Door Swing (Optional).......................................18

Complete Installation

DRYER USE........................................................................19

Starting Your Dryer.........................................................1 9

Drying Rack Option

DRYER CARE....................................................................20

Cleaning the Dryer Location Cleaning the Lint Screen

Cleaning the Dryer Interior..............................................21

Removing Accumulated Lint

Vacation and Moving Care..............................................21

Changing the Drum Light

TROUBLESHOOTING........................................................22

ASSISTANCE OR SERVICE

WARRANTY........................................................................25

......................................................................

.....................................................

.......................................................

.........................................................

........................................

..............................

............................

............................................

.................................................

...........................................

................................................

..............................................

20 20

ÍNDICE

SEGURIDAD DE LA SECADORA......................................27

INSTRUCCIONES DE INSTALACIÓN

ETerramientas y piezas...................................................28

Requisitos de ubicación...................................................29

5 7

Requisitos eléctricos - sólo en EE. UU.............................30

Conexión eléctrica - sólo en EE.UU

Requisitos de ventilación.................................................38

Planificación del sistema de ventilación

Instalación del sistema de ventilación.............................42

Instalación de las patas niveladoras

Conexión del ducto de escape

Nivelación de la secadora

Cómo invertir el cierre de la puerta (opcional)..................43

Complete la instalación

USO DE LA SECADORA

Puesta en marcha de su secadora..................................44

Opción de estante de secado.........................................4.5

CUIDADO DE LA SECADORA

Limpieza del lugar donde está la secadora

Limpieza del filtro de pelusa............................................46

Limpieza del interior de la secadora................................46

Eliminación de pelusa acumulada...................................46

Cuidado para las vacaciones y la mudanza

Cambio de la luz del tambor

SOLUCIÓN DE PROBLEMAS............................................48

AYUDA O SERVICIO TÉCNICO.........................................50

GARANTÍA ........................................................................51

...............................................

...................................................

............................................

...............................

................................

..........................

...............................

........................................

..........................................

.....................

....................

42 42 43

TABLE DES MATIÈRES

SÉCURITÉ DE LA SÉCHEUSE..........................................53

INSTRUCTIONS D'INSTALLATION...................................55

Outillage et pièces..........................................................5.5

Exigences d'emplacement...............................................55

Spécifications électriques Exigences concernant l'évacuation

Planification du système d'évacuation.............................59

Installation du système d'évacuation

Installation des pieds de nivellement...............................62

Raccordement du conduit d'évacuation Mise à niveau de la sécheuse Inversion du sens d'ouverture de la porte (facultatif)

Achever l'installation........................................................63

UTILISATION DE LA SÉCHEUSE

Mise en marche de la sécheuse

Option grille de séchage..................................................65

ENTRETIEN DE LA SÉCHEUSE.......................................66

Nettoyage de l'emplacement de la sécheuse..................66

Nettoyage du filtre à charpie

Nettoyage de l'intérieur de la sécheuse Comment enlever la charpie accumulée Précautions à prendre pour les vacances et avant un

déménagement................................................................67

Changement de l'ampoule du tambour............................67

DÉPANNAGE......................................................................68

ASSISTANCE OU SERVICE

GARANTIE

.........................................................................

................................................

.................................

..............................

..........................

.........................................

........

.....................................

......................................

...........................................

..........................

.........................

..............................................

57 58

62 62

66 66 67

DRYER SAFETY

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word “DANGER” or “WARNING.”

These words mean:

You can be killed or seriously injured if you don't immediately

▲DANGER

▲WARNING

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the dryer, follow basic precautions,

including the following:

Read all instructions before using the dryer. Do not place items exposed to cooking oils in your dryer,

items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry cleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode.

Do not allow children to play on or in the dryer. Close supervision of children is necessary when the dryer is used near children.

Before the dryer is removed from service or discarded, remove the door to the drying compartment.

Do not reach into the dryer if the drum is moving. Do not install or store the dryer where it will be exposed

to the weather. Do not tamper with controls.

follow instructions.

You can be killed or seriously injured if you don't follow instructions.

Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in this Use and Care Guide or in published user-repair instructions that you understand and have the skills to carry out.

Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

Clean lint screen before or after each load. Keep area around the exhaust opening and adjacent

surrounding areas free from the accumulation of lint, dust, and dirt.

The interior of the dryer and exhaust vent should be cleaned periodically by qualified service personnel.

See installation instructions for grounding requirements.

SAVE THESE INSTRUCTIONS

INSTALLATION INSTRUCTIONS

Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here.

Flat-blade screwdriver #2 Phillips screwdriver Adjustable wrench that

opens to 1" (2.54 cm) or hex-head socket wrench (for adjusting dryer feet)

Wire stripper (for U.S. only, direct wire installations)

Parts supplied

Remove parts packages from dryer drum. Check that all parts are included.

4 Leveling k‘gs

Parts needed

Check local codes. Check existing electrical supply and venting. See "Electrical Requirements" and "Venting Requirements" before purchasing parts.

Mobile home installations require metal exhaust system hardware available for purchase from the dealer from whom you purchased your dryer. For further information, please refer to the "Assistance or Service" section.

Tin snips (new vent installations)

Level Vent clamps Caulking gun and

compound (for installing new exhaust vent)

Tape measure

Lf]

Explosion Hazard

Keep flammable materials and vapors, such as gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor

for a garage installation. Failure to do so can result In death, explosion, or fire.

You will need

■ A location that allows for proper exhaust installation. See "Venting Requirements."

■ A separate 30-amp circuit.

■ If you are using a power supply cord, a grounded electrical outlet located within 2 ft (61 cm) of either side of the dryer. See "Electrical Requirements."

■ A sturdy floor to support the total weight (dryer and load) of 200 lbs (90.7 kg). The combined weight of a companion appliance should also be considered.

■ A level floor with a maximum slope of 1" (2.5 cm) under entire dryer. (If slope is greater than 1" [2.5 cm|, install Extended Dryer Feet Kit, Part Number 279810.) Clothes may not tumble properly and models with automatic sensor cycles may not operate correctly if dryer is not level.

Do not operate your dryer at temperatures below 45"F (7°C). At lower temperatures, the dryer might not shut off at the end of an automatic cycle. Drying times can be extended.

The dryer must not be installed or stored in an area where it will be exposed to water and/or weather.

Check code requirements. Some codes limit, or do not permit, installation of the dryer in garages, closets, mobile homes or sleeping quarters. Contact your local building inspector.

Installation Clearances

The location must be large enough to allow the dryer door to open fully.

Dryer Dimensions Companion appliance spacing should also be considered.

*Most installations require a minimum 5" (12.7 cm) clearance behind the dryer for the

exhaust vent with elbow. See "Venting Requirements."

Installation spacing for recessed area or closet installation

The following spacing dimensions are recommended for this dryer. This dryer has been tested for spacing of 0" (0 cm) clearance on the sides and rear. Recommended spacing should be considered for the following reasons:

■ Additional spacing should be considered for ease of installation and servicing,

■ Additional clearances might be required for vvalh door and floor moldings.

■ Additional spacing should be considered on all sides of the dryer to reduce noise transfer,

■ For closet installation, with a door, minimum ventilation openings in the top and bottom of the door are required. Louvered doors with equivalent ventilation openings are acceptable.

Electrical iecpirements - ■ ' ■ ■ ily

It is your responsibility

■ To contact a qualified electrical installer,

■ To be sure that the electrical connection is adequate and in conformance with the

National Electrical Code, ANSI/NFPA 70-latest edition and all local codes and

ordinances. The National Electric Code requires a 4-wire power supply connection for homes built

after 1996, dryer circuits involved in remodeling after 1996, and all mobile home

installations.

A copy of the above code standards can be obtained from: National Fire Protection Association, One Batterymarch Park, Quincy, MA 02269.

■ To supply the required 3 or 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply (or 3 or 4 wire, 1 20/208 volt electrical supply, if specified on the serial/rating plate) on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch circuit. Do not have a fuse in the neutral or grounding circuit.

(2.Son)

(73,66 cm)

(2.5 cm) (2.5 cm) (70.5 cm) (12.7 cm)

A. Recesied area

B. Side view - closet or confined area C. Closet door with vents

B c

‘Required spacing

Mobile Home - Additional Installation Requirements

This dryer is suitable for mobile home installations. The installation must conform to the Manufactured Ftome Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the

Federal Standard for Mobile Flome Construction and Safety, Title 24, HUD Part 280) or the

Canadian Manufactured Home Standard, CAN/CSA-Z240 MH,

Mobile home installations require:

■ Metal exhaust system hardware, which is available for purchase from your dealer.

■ Special provisions must be made in mobile homes to Introduce outside air into the dryer. The opening (such as a nearby window) should be at least twice as large as the dryer exhaust opening.

■ Do not use an extension cord,

■ If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.

Electrical Connection

To properly install your dryer, you must determine the type of electrical connection you will

be using and follow the instructions provided for it here.

■ This dryer is manufactured ready to install with a 3-wire electrical supply connection. The neutral ground conductor is permanently connected to the neutral conductor (white wire) within the dryer. If the dryer is installed with a 4-wire electrical supply connection, the neutral ground conductor must be removed from the external ground connector (green screw), and secured under the neutral terminal (center or white wire) of the terminal block. When the neutral ground conductor is secured under the neutral terminal (center or white wire) of the terminal block, the dryer cabinet is isolated from the neutral conductor.

■ If local codes do not permit the connection of a neutral ground wire to the neutral wire, see "Optional 3-wire connection" section in "Electrical Connection - U.S.A. Only" section.

■ A 4-wire power supply connection must be used when the appliance is installed in a location where grounding through the neutral conductor is prohibited. Grounding through the neutral is prohibited for (1) new branch-circuit installations, [2) mobile homes, (3) recreational vehicles, and (4j areas where local codes prohibit grounding through the neutral conductors.

If using a power supply cord:

Use a UL listed power supply cord kit marked for use with clothes dryers. The kit should contain:

■ A Ul. listed 30-amp power supply cord, rated 120/240 volt minimum. The cord should be type SRD or SRDT and be at least 4 ft (1.22 m) long. The wires that connect to the dryer must end in ring terminals or spade terminals with upturned ends.

■ A UL listed strain relief.

If your outlet looks like this:

4-wire receptacle (14-30R)

Then choose a 4-wire power supply cord with ring or spade terminals and Ul., listed strain relief. The 4-wire power supply cord, at least 4 ft (1.22 m) long, must have four 10-gauge copper wires and match a 4-wire receptacle of NEMA Type 14-30R. The ground wire (ground conductor) may be either green or bare. The neutral conductor must be identified by a white cover.

If your outlet looks like this:

If connecting by direct wire:

Power supply cable must match power supply (4-wire or 3-wire) and be:

■ Flexible armored cable or nonmetallic sheathed copper cable (with ground wire), protected with flexible metallic conduit. All current-carrying wires must be insulated.

■ 1 0-gauge solid copper wire (do not use aluminum).

■ At least 5 ft (1.52 m) long.

GROUNDING INSTRUCTIONS

® For a grounded, cord-connected dryer:

This dryer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This dryer uses a cord having an equipment-grounding

conductor and a grounding plug. The plug must be plugged

into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

■ For a permanently connected dryer: This dryer must be connected to a grounded metal, permanent wiring system, or an equipment-grounding

conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the dryer.

WARNING: Improper connection of the equipment

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug on the power supply cord: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

3-wire receptacle (10-30R)

Then choose a 3-wire power supply cord with ring or spade terminals and Ul. listed strain relief. The 3-wire power supply cord, at least 4 ft (1.22 m) long, must have three 10-gauge copper wires and match a 3-wire receptacle of NEMA Type 1 0-30R,

SAVE THESE INSTRUCTIONS

Electrical iec|iiirements - Canada Only

■ Do not use an extension cord.

^WARNING

Electrical Shock Hazard

Plug into a grounded 4 prong outlet. Failure to do so can result in death or eiectricai shock.

It is your responsibility

■ To contact a qualified electrical installer,

■ To be sure that the electrical connection is adequate and in conformance with the Canadian Electrical Code, C22.1 -latest edition and all local codes. A copy of the above codes standard may be obtained from; Canadian Standards Association, 178 Rexdale Blvd., Toronto, ON M9W 1R3 CANADA.

■ To supply the required 4 wire, single phase, 120/240 volt, 60 Hz., AC only electrical supply on a separate 30-amp circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. Connect to an individual branch circuit.

■ This dryer is equipped with a CSA international Certified Power Cord intended to be

plugged into a standard 14-30R wall receptacle. The cord is 5 ft (1,52 m) in length. Be

sure wall receptacle is within reach of dryer's final location.

If you are using a replacement power supply cord, it is recommended that you use Power Supply Cord Replacement Part Number 3394208. For further information, please reference the service numbers located in the "Assistance or Service" section.

GROUNDING INSTRUCTIONS

■ For a grounded, cord-connected dryer: This dryer must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This dryer is equipped with a cord having an equipment grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

WARNING: Improper connection of the equipment

grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative or personnel if you are in doubt as to whether the dryer is properly grounded. Do not modify the plug provided with the dryer: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

SAVE THESE INSTRUCTIONS

4-wire receptacle 14-30R

Power Supply Cord Direct Wire

▲WARNING

Fire Hazard

Use a new UL listed 30 amp power supply cord. Use a UL listed strain relief. Disconnect power before making electrical connections. Connect neutral wire (white or center wire) to center

terminal (silver). Ground wire (green or bare wire) must be connected to

green ground connector. Connect remaining 2 supply wires to remaining

2 terminals (gold). Securely tighten all electrical connections.

Failure to do so can result In death, fire, or

electrical shock.

1. Disconnect power,

2. Remove the hold-down screw and terminal block cover.

B C D

▲WARNING

Fire Hazard Use 10 gauge solid copper wire. Use a UL listed strain relief.

Disconnect power before making electrical connections.

Connect neutral wire (white or center wire) to center terminal (silver).

Ground wire (green or bare wire) must be connected to green ground connector.

Connect remaining 2 supply wires to remaining 2 terminals (gold).

Securely tighten all electrical connections. Failure to do so can result in death, fire, or

electrical shock.

Style 1: Power supply cord strain relief

■ Remove the screws from a %" (1,9 cm) Ul. listed strain relief (UL marking on strain relief). Put the tabs of the two clamp sections into the hole below the terminal block

opening so that one tab is pointing up and the other is pointing down, and hold in

place. Tighten strain relief screws just enough to hold the two clamp sections together.

/1, Termiiitil block cover

B. External ground conductor

screw

C. Center, silverwolorerj terminal

block screw

D. Hold-down screw location

E. Neutral ground wire f. Hole below terminal block

opening

' '

.......

A. Strain relief tab pointing up

B. Hole below terminal block opening C. Clamp section D. Strain relief tab pointing down

Put power supply cord through the strain relief. Be sure that the wire insulation on the power supply cord is inside the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Do not further tighten strain relief screws at this point.

Put direct wire cable through the strain relief. The strain relief should have a tight fit with the dryer cabinet and be in a horizontal position. Tighten strain relief screw against the direct wire cable.

Style 2: Direct wire strain relief

■ Unscrew the removable conduit connector and any screws from a %" (1.9 cm) Ul. listed strain relief (UL marking on strain relief). Put the threaded section of the strain relief through the hole below the terminal block opening. Reaching inside the terminal block opening, screw the removable conduit connector onto the strain relief threads.

A. Removable conduit connector

B. Hole below terminal block opening

C. Strain relief threads

4. Now complete installation following instructions for your type of electrical connection: 4-wire (recommended)

3-wire (if 4-wire is not available)

Electrical Connection Options

If your home has:

4-wire receptacle (NEMAType 14-30R)

/"'u\

And you will be connecting to:

A UL listed,

120/240-volt minimum, 30-amp, dryer power supply cord*

Go to Section

4-wire connection: Power supply cord

( a D

4-wire direct A fused disconnect or

3-wire receptacle (NEMA type 10-30R)

circuit breaker box*

A UL listed,

120/240-volt minimum, 30-amp, dryer power supply cord*

^ OJ

3-wire direct

A fused disconnect or circuit breaker box*

4-wire connection: Direct Wire

3-wire connection: Power supply cord

3-wire connection: Direct Wire

(8.9 cm)

*if local codes do not permit the connection of a cabinet-ground conductor to the neutral

wire, go to "Optional 3-wire connection" section.

4-wire connection: Power Supply Cord

3. Connect ground wire (green or bare) of power supply cord to external ground conductor screw. Tighten screw.

IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do

not permit the use of 3-wire connections.

A. 4-wire receptacle (NEMA type 14-30R)

B. 4-prong plug C. Cround prong D. Neutral prong

E. Spade terminah with upturned endf

F. ■%" (1.9 cm) UL listed terrain relief C. Ring terminals

Remove center silver-colored terminal block screw.

Remove neutral ground wire from external ground conductor screw. Connect neutral ground wire and the neutral wire (white or center wire) of power supply cord under center, silver-colored terminal block screw. Tighten screw.

A. External ground conductor screw

B. Center silver-colored terminal block screw C. Neutral wire (white or center wire) D. %" (t.9 cm) UL listed strain relief

E. Cround wire (green or bare) of power supply cord

F. Neutral ground wire

Connect the other wires to outer terminal block screws. Tighten screws.

Tighten strain relief screws.

Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold

down screw.

7. You have completed your electrical connections. Now go to "Venting Requirements."

A. External ground conductor screw - Dotted line shows

position of NEUTELAL ground wire before being moved to center silver-colored terminal block screw.

B. Center silver-colored terminal block screw C. Neutral wire (white or center wire) D. Vs" (1.9 cm) UL listed strain relief

E. Neutral ground wire

4-wire connection: Direct Wire

IMPORTANT: A 4-wire connection is required for mobile homes and where local codes do

not permit the use of 3-wire connections. Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed. Strip 5" (12.7 cm) of outer covering from end of cable, leaving bare ground wire at 5"

(12.7 cm). Cut 11/2" (3.8 cm) from 3 remaining wires. Strip insulation back 1" (2.5 cm). Shape ends of wires into a hook shape.

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw, as shown.

1.2.Remove center silver-colored terminal block screw. Remove neutral ground wire from external ground conductor screw. Connect neutral

ground wire and place the hooked end (hook facing right) of the neutral wire (white or center wire) of direct wire cable under the center screw of the terminal block. Squeeze

hooked ends together. Tighten screw.

/4 B

3. Connect ground wire (green or bare) of power supply cable to external ground conductor screw. Tighten screw.

/4 B

/t. External ground conductor screw

B. Center silver-colored terminal block screw C. Neutral wire (white or center wire) D. Vs" ( T9 cm) UL listed strain relief

E. Ground wire (green or bare) of power supply cable

F. Neutral ground wire

4. Place the hooked ends of the other power supply cable wires under the outer terminal block screws (hooks facing right). Squeeze hooked ends together. Tighten screws.

A. External gi'ound conductor screw - Dotted line shows

position of NEUTRAL ground wire before being moved to center silver-colored terminal block screw.

B. Center silver-colored terminal block screw C. Neutral wire (white or center wire) D. %" (T9 cm) UL listed strain relief

E. Neutral ground wire

I t

5. Tighten strain relief screws.

6. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold down screw.

7. You have completed your electrical connections. Now go to "Venting Requirements."

3-wire connection: Power Supply Cord

3-wire connection: Direct Wire

Use where local codes permit connecting cabinet-ground conductor to neutral wire:

B. 3-wire plug C. Neutral prong

D. Spade terminals with up turned ends

E. {1.9 cm) UL listed strain relief F. Ring terminals

C. Neutral (white or center wire)

1. Loosen or remove center silver-colored terminal block screw.

2. Connect neutral wire (white or center wire) of power supply cord to the center, silver-

colored terminal screw of the terminal block. Tighten screw.

Use where local codes permit connecting cabinet-ground conductor to neutral wire.

Direct wire cable must have 5 ft (1.52 m) of extra length so dryer can be moved if needed. Strip 31/2" (8,9 cm) of outer covering from end of cable. Strip insulation back 1" (2.5 cm). If

using 3-wire cable with ground wire, cut bare wire even with outer covering. Bend ends of wires into a hook shape.

When connecting to the terminal block, place the hooked end of the wire under the screw of the terminal block (hook facing right), squeeze hooked end together and tighten screw, as shown.

1. Loosen or remove center silver-colored terminal block screw.

2. Place the hooked end of the neutral wire (white or center wire) of power supply cable under the center screw of terminal block (hook facing right). Squeeze hooked end together. Tighten screw

A. Neutral ground wire

B. External ground conductor screw C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

E. ¥4" (1.9 cm) UL listed strain relief

3. Connect the other wires to outer terminal block screws. Tighten screws.

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold down screw.

6. You have completed your electrical connections. Now go to "Venting Requirements."

A. Neutral ground wire

B. External ground conductor screw

C. Center silverwohred terminal block screw

D. Neutral wire (white or center wire)

E. yC (1.9 cm) UL listed strain relief

3, Place the hooked ends of the other power supply cable wires under the outer terminal

block screws (hooks facing rightj. Squeeze hooked ends together. Tighten screws.

B c

-D

""E

A. External ground conductor screw

B. Neutral ground wire C. Center silver-colored terminal block screw

D. Neutral wire (white or center wire)

E. %" (1.9 cm) UL listed strain relief E Grounding path determined by a qualified electrician

3. Connect the other wires to outer terminal block screws. Tighten screws.

4, Tighten strain relief screw. 5, Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold

down screw.

6, You have completed your electrical connections. Now go to "Venting Requirements."

Optional 3-wire connection

Use for direct wire or power supply cord where local codes do not permit connecting cabinet-ground conductor to neutral wire.

1, Remove center silver-colored terminal block screw.

2, Remove neutral ground wire from external ground conductor screw. Connect neutral

ground wire and the neutral wire (white or center wire) of power supply cord/cable under center, silver-colored terminal block screw. Tighten screw.

4. Tighten strain relief screws.

5. Insert tab of terminal block cover into slot of dryer rear panel. Secure cover with hold down screw.

6. Connect a separate copper ground wire from the external ground conductor screw to an adequate ground.

entine

^WARNING

JÉ

Fire Hazard

Use a heavy metal vent Do not use a plastic vent Do not use a metal foil vent. Failure to follow these Instructions can result In death

or fire.

WARNING: To reduce the risk of fire, this dryer MUST BE EXHAUSTED OUTDOORS,

IMPORTANT: Observe all governing codes and ordinances.

The dryer exhaust must not be connected into any gas vent, chimney, wall, ceiling or a concealed space of a building.

llirt'l I itfi list

Rigid metal vent

■ Eor best drying performance, rigid metal vents are recommended.

■ Rigid metal vent is recommended to avoid crushing and kinking.

Flexible metal vent

■ flexible metal vents are acceptable only if accessible for cleaning.

■ flexible metal vent must be fully extended and supported when the dryer is in its final location,

■ Remove excess flexible metal vent to avoid sagging and kinking that may result in reduced airflow and poor performance,

■ Do not install flexible metal vent in enclosed walls, ceilings or floors.

Elbows

45° elbows provide better airflow than 90° elbows.

If using an existing vent system

Clean lint from the entire length of the system and make sure exhaust hood is not plugged with lint.

Replace any plastic or metal foil vent with rigid or flexible heavy metal vent. Review Vent system chart. Modify existing vent system if necessary to achieve the best

drying performance.

If this is a new vent system

Vent material

■ Use a heavy metal vent. Do not use plastic or metal foil vent.

■ 4" (10.2 cm) heavy metal exhaust vent and clamps must be used.

4“ (10.2 cm) heavy metal exhaust vent

Vent products can be purchased from your dealer or by calling Maytag Services. For more information, see the "Assistance or Service" section.

Good Better

Clamps

■ Use clamps to seal all joints.

■ Exhaust vent must not be connected or secured with screws or other fastening devices that extend into the interior of the duct. Do not use duct tape.

Clamp

Exhaust

Recommended hood styles are shown here.

Plan ■ ■■■

Choose your exhaust installation type

Recommended exhaust installations

Typical installations vent the dryer from the rear of the dryer. Other installations are possible.

A. Louvered hood style

B. Box hood style

The angled hood style (shown here) is acceptable.

An exhaust hood should cap the vent to keep rodents and insects from entering the home.

Exhaust hood must be at least 12" (30.5 cm) from the ground or any object that may be in

the path of the exhaust (such as flowers, rocks or bushes, snow line, etc.).

FOo not use an exhaust hood with a magnetic latch.

Improper venting can cause moisture and lint to collect indoors, which may result in:

■ Moisture damage to woodwork, furniture, paint, wallpaper, carpets, etc.

■ Housecleaning problems and health problems.

■E F

A. Dryer E. Clamps

B. Elbow E. Rigid metal or flexible metal vent

C. Wall C. Vent length necessary to connect elbows

D. Exhaust hood H. Exhaust outlet

Standard exhaust installation with rigid metal or flexible metal vent

Alternate installations for close clearances

Venting systems come in many varieties. Select the type best for your installation. Two closeclearance installations are shown. Refer to the manufacturer's instructions.

A. Over-the-top inftaliation (ako available with one offset elbow)

B. Periscope installation

NOTE: The following kits for close clearance alternate installations are available for purchase. Please see the "Assistance or Service" section to order.

■ Over-the-Top Installation: Part Number 4396028

■ Periscope Installation (For use with dryer vent to wall vent mismatch): Part Number 4396037 - 0" (0 cm) to 18" (45,72 cm) mismatch Part Number 4396011 - 1 8" (45.72 cm) to 29" (73.66 cm) mismatch Part Number 4396014 - 29" (73.66 cm) to 50" (127 cm) mismatch

Special provisions for mobile home installations

The exhaust vent must be securely fastened to a noncombustible portion of the mobile home structure and must not terminate beneath the mobile home. Terminate the exhaust vent outside.

Determine vent path

Select the route that will provide the straightest and most direct path outdoors. Plan the installation to use the fewest number of elbows and turns. When using elbows or making turns, allow as much room as possible. Bend vent gradually to avoid kinking. Use the fewest 90° turns possible.

Determine vent length and elbows needed for best drying performance

■ Use the Vent system chart below to determine type of vent material and hood combinations acceptable to use.

NOTE: Do not use vent runs longer than those specified in the Vent system chart. Exhaust systems longer than those specified will;

■ Shorten the life of the dryer.

■ Reduce performance, resulting in longer drying times and increased energy usage.

The Vent system chart provides venting requirements that will help to achieve the best drying performance.

Vent systems charts

When using only one type of metal vent:

Use the following chart to help you determine your maximum vent length based on the number of 90° [urns or elbows you will rteed artd lire type of verrt (rigid arrd/or flexible metal) you will use.

Vent system chart

Number of 90“

turns or elbows 0 1 '0 ft (36.6 m) 40 ft (12,2 m) 1 11 0 ft (33.5 m) 37 ft (11,3 m) 2 1 00 ft (30.5 m) 33 ft (10,1 m) 3 90 ft (27.4 m) 30 ft (9.1 m) 4 80 ft (24.4 m) 27 ft (8.2 m) 5 70 ft (21,3 m) 23 ft (7.0 m)

Rigid metal vent Flexible metal vent

When using a combination of rigid and flexible metal vent:

Use the following charts to help you determine your maximum vent length based on the number of 90° turns or elbows you will need.

■ Determine the number of elbows or turns you will need.

■ Determine the length of the fully extended flexible metal vent you will use. Find the

column that has the nearest number of feet to what you will be using.

■ Match the number of turns or elbows with the length of the fully extended flexible

metal vent you will use to find the maximum length of rigid metal vent you can use.

Vent system chart - 0 ft {0 m) to 10 ft (3.0 m)

No. of turns or elbows

0 120 ft

1 110 ft

2 100 ft

3 90 ft

4 80 ft

5 70 ft

0 ft (0 m)

(36.6 m)

(33.S m)

(30.5 m)

(27.4 m)

(24.4 m)

(21.3 m)

1 -5 ft

(0.3-1.5 m)

105 ft

(32.0 m) 95 ft

(29.0 m) 85 ft

(25.9 m)

75 ft

(22.9 m) 65 ft

(1 9.8 m) 55 ft

(1 6.8 m)

6-10 . (1.8-3.0 m)

90 ft (27.4 m)

80 ft (24.4 m)

70 ft (21.3 m)

60 ft (1 8.3 m)

50 ft (1 5.2 m)

40 ft (1 2.2 m)

Length of flexible metal vent

Length of rigid metal vent

Vent system chart - 11 ft (3.4 m) to 25 ft (7.6 m)

No. of

turns or elbows

0 75 ft

1 65 ft

2 55 ft

3 45 ft

4 35 ft

5 25 ft

t. Install exhaust hood. Use caulking compound to seal exterior wall opening around

exhaust hood.

2. Connect vent to exhaust hood. Vent must fit inside exhaust hood. Secure vent to exhaust hood with 4" (10.2 cm) clamp.

11-15 ft (3.4-4,6 m)

(22,9 m)

(19.8 m)

(1 6.8 m)

(1 3.7 m)

(10.7 m)

(7.6 m)

16-20 ft

(4.9-6,1 m)

60 ft (1 8,3 m)

50 ft (1 5.2 m)

40 ft (12.2 m)

30 ft (9.1 m)

20 ft (6.1 m)

10 ft

(3.0 m)

Install Vnnt Sys item

21-25 ft (6.4-7,6 m)

45 ft (1 3,7 m)

35 ft (10.7 m)

25 ft (7.6 m)

15 ft

(4.6 m) 5 ft

(1.5 m) 0 ft

(0 m)

Length of flexible metal vent

Length of rigid metal vent

3. Run vent to dryer location. Use the straightest path possible. See "Determine vent path" in "Plan Vent System." Avoid 90° turns. Use clamps to seal all joints. Do not use duct tape,

screws or other fastening devices that extend into the interior of the vent to secure vent.

install Leveling Legs

Excessive Weight Hazard

Use two or more people to move and install dryer. Failure to do so can result in back or other injury.

1. To protect the floor, use a large, flat piece of cardboard from the dryer carton. Place

cardboard under the entire back side of the dryer.

2. Firmly grasp the body of the dryer (not the top or console panel). Gently lay the dryer on

the cardboard. See illustration.

3, Examine the leveling legs. Find

diamond marking is no longer visible.

Place a carton corner post from dryer packaging under each of the 2 dryer back corners.

Stand the dryer up. Slide the dryer on the corner posts until it is close to its final location.

Leave enough room to connect the exhaust vent.

Using a 4" (1 0.2 cm) clamp, connect vent to exhaust outlet in dryer. If connecting to

existing vent, make sure the vent is clean. The dryer vent must fit over the dryer exhaust outlet and inside the exhaust hood. Check that the vent is secured to exhaust hood with a 4" (1 0.2 cm) clamp.

Jim •

4. Once the exhaust vent connection is made, remove the corner posts and cardboard.

I fm

Check the levelness of the dryer. Check levelness first side to side, then front to back.

/ “

6. Insert screws into bottom holes on left side of cabinet. Tighten screws halfway. Position

door so large end of door hinge slot is over screws. Slide door up so screws are in bottom of slots. Tighten screws. Insert and tighten top screws in hinges.

If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for levelness.

You can change your door swing from a right-side opening to a left-side opening, if desired.

Place towel (A) on top of dryer to protect surface.

Open dryer door. Remove bottom screws from cabinet side of hinges (C). Loosen (do not remove) top screws from cabinet side of hinges.

Lift door until top screws in cabinet are in large part of hinge slot. Pull door forward off screws. Set door (handle side up) on top of dryer. Remove top screws from cabinet.

Remove screws attaching hinges to door.

Use a small, flat-blade screwdriver to gently remove 4 hinge hole plugs (D) on left side of cabinet. Insert plugs into hinge holes on right side of cabinet.

7. Close door and check that door strike aligns with door catch (B), If it is needed, slide door catch left or right within slot to adjust alignment.

' - ■ ^ ■ italiaticin

1. Check that all parts are now installed. If there is an extra part, go back through the steps to see which step was skipped.

2. Check that you have all of your tools.

3. Dispose of/recycle all packaging materials,

4. Check the dryer's final location. Be sure the vent is not crushed or kinked.

5. Check that the dryer is level. See "level Dryer."

6. In the U.S.A,

■ For power supply cord installation, plug into an outlet. For direct wire installation,

turn on power.

In Canada

■ Plug into a grounded 4 prong outlet. Turn on power.

7. Remove any protective film on the console and any tape remaining on the dryer.

8. Read "Dryer Use."

9. Wipe the dryer drum interior thoroughly with a damp cloth to remove any dust.

10. Set the dryer on a full heat cycle (not an air cycle) for 20 minutes and start the dryer. If the dryer will not start, check the following:

Controls are set in a running or "On" position. Start button has been pushed firmly.

Dryer is plugged into an outlet and/or electrical supply is on. Ffousehold fuse is intact and tight, or circuit breaker has not tripped. Dryer door is closed.

11. When the dryer has been running for 5 minutes, open the dryer door and feel for heat. If you feel heat, cancel cycle and close the door.

If you do not feel heat, turn off the dryer and check the following:

■ There may be 2 household fuses or circuit breakers for the dryer. Check that both fuses

are intact and tight, or that both circuit breakers have not tripped. If there is still no

heat, contact a qualified technician.

NOTE: You may notice a burning odor when the dryer is first heated.' when the heating element is first used. The odor will go away.

tIs odor Is common

DRYER USE

AWARNING

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer. Do not dry anything that has ever had anything

flammable on it (even after washing). Failure to follow these instructions can result in death,

explosion, or fire.

WARNING: To reduce the risk of fire, electric shock, or injury to persons, read the

IMPORTANT SAFETY INSTRUCTIONS before operating this appliance. This book covers several different models. Your dryer may not have all of the cycles and

features described. Before using your dryer, wipe the dryer drum with a damp doth to remove dust from storing

and shipping.

1. Clean lint screen before each load. See "Cleaning the Lint Screen."

2. Load clothes loosely into the dryer and close the door. Do not pack the dryer. Allow space for clothes to tumble freely.

3. Turn the Cycle Control knob to the recommended cycle for the type of load being dried.

Use the Energy Preferred setting (*) to dry most heavy to medium-weight fabrics.

4. If your dryer has a Temperature selector, set it to the recommended setting for the type of fabric being dried. See "Dryer Cycle Descriptions" (separate sheet) for temperature suggestions. On some models, temperature is included in the cycle selections.

5. (OPTIONAL) Your dryer may have a WRINKLE PREVENT feature selector. When you are

unable to remove a load from the dryer as soon as it stops, wrinkles can form. This feature periodically tumbles, rearranges and fluffs the load without heat to help smooth out

wrinkles.

6. (OPTIONAL] Your dryer may have an END OE CYCLE SIGNAL. The signal is helpful when drying items that should be removed from the dryer as soon as it stops.

■ On some models, the volume of the End of Cycle signal can be adjusted. Turn the

selector to the desired volume.

AWARNING

Fire Hazard

No washer can completely remove oil. Do not dry anything that has ever had any type of oil on

It (including cooking oils). Items containing foam, rubber, or plastic must be dried

on a clothesline or by using an Air Cycle. Failure to follow these instructions can result in death

or fire.

■ On other models, the End of Cycle signal is part of the Start button and is selectable. Turn the START button to ON or OEE. The signal will sound only if the selector is set to On.

7. Select the desired Option. See "Dryer Cycle Descriptions" (separate sheet).

8. If desired, add fabric softener sheet. Follow instructions on the package.

9. Push the START button.

How Automatic Drying Works

When you are using the Auto Moisture Sensing Cycle, the dryness of the load is determined

by two metal strips (sensors] located on the inside of the dryer. The metal strips help "feel" the amount of moisture left in the clothes as they tumble. When moisture is left in the clothes, the Cycle Control knob will not advance. As clothes begin to dry, the amount of water left in the clothes decreases, and the timer advances through the remainder of the cycle. When the selected dryness level is reached, the dryer goes into a cool down period of up to 10 minutes.

Stopping and Restarting

You can stop your dryer anytime during a cycle.

To stop your dryer

Open the dryer door or turn the Cycle Control knob to OFF.

NOTE: The Cycle Control knob should point to an Off area when the dryer is not in use.

To restart your dryer

t. Close the door.

2. Select a new cycle and temperature (if desired).

3. Push the START button.

Drying Rack Option

Use the Drying Rack to dry items such as sweaters and pillows without tumbling. The drum turns, but the rack does not move.

If your model does not have a drying rack, you may be able to purchase one for your model. To find out whether your model allows drying rack usage and for information on ordering, please refer to the front page of the manual or contact the dealer from whom you purchased your dryer,

NOTE: The rack must be removed for normal tumbling. Do not use the automatic cycle with the drying rack.

To use the drying rack

1. Place drying rack in dryer. Style 1 : Your drying rack has front legs. Slide rear pegs into the dimples on the back wall

of the dryer. Lower the front legs to rest on the dryer opening. Style 2: Your drying rack does not have front legs. Do not remove the lint screen. Slide

drying rack over the bottom of the dryer door opening. Push down to secure rack on frame.

DRYER CARE

f r'f ;. ..■■■ : :. ■■■... ■ .tiiin

Keep dryer area clear and free from items that would obstruct the flow of combustion and ventilation air.

AWARNING

Aliy

2. Put wet items on top of rack, leaving space between items. Do not allow items to hang over the edge of the rack. Close the door.

3. Select a timed drying cycle and temperature, or an air cycle. Items containing foam, rubber, or plastic must be dried on a clothesline or by using an air cycle. Refer to the following table.

4. Start the dryer. Reset cycle to complete drying, if needed.

Rack Dry Cycle Temp Time

Washable wool items (block to shape, lay flat on rack)

Stuffed toys/pillows (cotton or polyester filled)

Stuffed toys/pillows Foam rubber filled

Clean lint screen before each load. A screen blocked by lint can increase drying time,

IMPORTANT:

■ Do not run the dryer with the lint screen loose, damaged, blocked or missing. Doing so can cause overheating and damage to both the dryer and fabrics.

■ If lint falls off the screen into the dryer during removal, check the exhaust hood and remove the lint.

Every Load Cleaning

Ti med

Drying

1 imed

Drying

Air (no heat)

l.ow 60 min.

Low 60 min.

N/A 90 min.

Explosion Hazard

Keep flammable materials and vapors, such as

gasoline, away from dryer.

Place dryer at least 18 inches (46 cm) above the floor

for a garage installation.

Failure to do so can result in death, explosion, or fire.

1. The lint screen is located on top of the dryer. Pull the lint screen toward you. Roll lint off

the screen with your fingers. Do not rinse or wash screen to remove lint. Wet lint is hard to remove.

2. Push the lint screen firmly back into place.

As Needed Cleaning

1, Roll lint off the screen with your fingers. 2, Wet both sides of lint screen with hot water. 3, Wet a nylon brush with hot water and liquid detergent. Scrub lint screen with the brush to

remove residue buildup. 4, Rinse screen with hot water. 5, Thoroughly dry lint screen with a clean towel. Replace screen in dryer.

For direct-wired dryers:

Clear''.,: : ■ s.'.:

1, Apply a liquid, nonflammable household cleaner to the stained area of the drum and rub

with a soft cloth until stain is removed, 2, Wipe drum thoroughly with a damp cloth. 3, Tumble a load of clean cloths or towels to dry the drum, NOTE: Garments that contain unstable dyes, such as denim blue jeans or brightly colored

cotton items, may discolor the dryer interior. These stains are not harmful to your dryer and will not stain future loads of clothes. Dry unstable dye items inside-out to avoid transfer of dye.

flemcivirig ■■ ■ ;.f...

From Inside the Dryer Cabinet

Lint should be removed every 2 years, or more often, depending on dryer usage. Cleaning should be done by a qualified person.

From the Exhaust Vent

Lint should be removed every 2 years, or more often, depending on dryer usage.

Vacation

Vacation care

Operate your dryer only when you are at home. If you will be on vacation or not using your dryer for an extended period of time, you should:

1, Unplug dryer or disconnect power. 2, Clean lint screen. See "Cleaning the Lint Screen,"

Moving care

Electrical Shock Hazard

Disconnect power before servicing. Replace all parts and panels before operating. Failure to do so can result In death or electrical shock.

t. Disconnect power.

2. Disconnect wiring,

3. Make sure leveling legs are secure in dryer base.

4. Use masking tape to secure dryer door.

1. Unplug dryer or disconnect power.

2. Open the dryer door. I.ocate the light bulb cover on the back wall of the dryer. Remove the screw located in the lower right-hand corner of the cover. Remove the cover.

3. Turn bulb counterclockwise. Replace the bulb with a 1 0-watt appliance bulb only. Replace the cover and secure with the screw.

4. Plug in dryer or reconnect power.

For power supply cord-connected dryers:

1, Unplug the power supply cord. 2, Make sure leveling legs are secure in dryer base. 3, Use masking tape to secure dryer door.

TROUBLESHOOTING

First try the solutions suggested here and possibly avoid the cost of a service call.

Dryer Operation

Dryer will not run

Has a household fuse blown, or has a circuit breaker tripped?

Electric dryers use 2 household fuses or circuit breakers. The drum may be turning, but you may not have heat. Replace the fuse or reset the circuit breaker. If the problem continues, call an electrician.

Is tbe correct power supply available?

Electric dryers require 240-volt power supply. Check with a qualified electrician.

Was a regular fuse used?

Use a time-delay fuse.

Is the dryer door firmly closed? Was the Start button firmly pressed? Is a cycle selected?

The dryer will not start in the Wrinkle Prevent position. Move the dial past OFF.

No heat

Has a household fuse blown, or bas a circuit breaker tripped?

Unusual sounds

Has tbe dryer bad a period of non-use?

If the dryer hasn't been used for a while, there may be a thumping sound during the first few minutes of operation.

Is a coin, button, or paper clip caught between tbe drum and front or rear of the dryer?

Check the front and rear edges of the drum for small objects. Clean out pockets before laundering.

Are the four legs installed, and is the dryer level front to back and side to side?

The dryer may vibrate if not properly installed. See the Installation Instructions.

Is the clothing knotted or balled up?

When balled up, the load will bounce, causing the dryer to vibrate. Separate the load items and restart the dryer.

Timer does not noticeably advance

Is the dryer set to Timed or Air Dry?

The timer moves slowly and continuously for the time setting.

Is the dryer set to Automatic Drying?

The timer moves only when the clothing is mostly dry. See "How Automatic Drying Works" in "Dryer Use."

Dryer Results

clothes are not drying satisfactorily, drying times are too long, or load is too hot

Is the lint screen clogged with lint?

Lint screen should be cleaned before each load.

Fire Hazard

Use a heavy metal vent.

Do not use a plastic vent. Do not use a metal foil vent

Failure to follow these instructions can result in death or fire.

Is the exhaust vent or outside exhaust hood clogged with lint, restricting air movement?

Run the dryer for 5-10 minutes. Hold your hand under the outside exhaust hood to check air movement. If you do not feel air movement, clean exhaust system of lint or replace exhaust vent with heavy metal or flexible metal vent. See the Installation Instructions.

Are fabric softener sheets blocking the grille?

Use only one fabric softener sheet, and use it only once.

Is the exhaust vent the correct length?

Check that the exhaust vent is not too long or has too many turns. Long venting will increase drying times. See the Installation Instructions.

Is the exhaust vent diameter the correct size?

Use 4" (1 0.2 cm) diameter vent material.

+ 50 hidden pages

Maytag MED5591TQ1 User Manual [en, es, fr]

Specifications and Main Features

Frequently Asked Questions

User Manual

DRYER SAFETY

▲DANGER

▲WARNING

INSTALLATION INSTRUCTIONS

Electrical iecpirements - ■ ' ■ ■ ily

Electrical iec|iiirements - Canada Only

^WARNING

install Leveling Legs

' - ■ ^ ■ italiaticin

DRYER USE

AWARNING

AWARNING

DRYER CARE

AWARNING

Vacation

TROUBLESHOOTING

Dryer Operation

Dryer Results