Maxtor DIAMONDMAX 21 PATA User Manual

Product Manual

DiamondMax 21 PATA

STM3320820A

STM3300620A

STM3250620A

STM3250820A

STM3200820A

STM3160215A

STM380215A

100451230 Rev. B September 2007

Revision status summary sheet

Revision Date Sheets Affected

Rev. A 11/16/06 Initial Release. Rev. B 09/21/07 Front cover, 1, 3, 8-13, 16-18, 22 and 33.

Publication number: 100451230, Rev. B September 2007

Seagate, Seagate Technology and the Wave logo are registered trademarks of Seagate Technology LLC in the United States and/or other countries. DiamondMax, MaxBlast, Maxtor and the Maxtor logo are either trademarks or registered trademarks of Seagate Technology LLC or one of its affiliated companies in the United States and/or other countries. All other trademarks or registered trademarks are the property of their respective owners.

One gigabyte, or GB, equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment and formatting. Seagate reserves the right to change, with out notice, product offerings or specifications.

Contents

1.0 Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2.0 Drive specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.1 Specification summary tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

2.2 Formatted capacity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.2.1 LBA mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.3 Default logical geometry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.4 Recording and interface technology . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.5 Physical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.6 Seek time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.7 Start/stop times . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.8 Power specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.8.1 Power consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.8.2 Conducted noise . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.8.3 Voltage tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.8.4 Power-management modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

2.9 Environmental specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.9.1 Ambient temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.9.2 Temperature gradient. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.9.3 Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.9.4 Altitude . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

2.9.5 Shock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.9.6 Vibration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

2.10 Acoustics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

2.11 Electromagnetic immunity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

2.12 Reliability . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.12.1 Annualized Failure Rate (AFR and Mean Time Between Failures (MTBF) . . . . 20

2.13 Agency certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.13.1 Safety certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.13.2 Electromagnetic compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

2.13.3 FCC verification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

2.14 Environmental protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

2.14.1 European Union Restriction of Hazardous Substances (RoHS) Directive . . . . . 22

2.14.2 China Restriction of Hazardous Substances (RoHS) Directive . . . . . . . . . . . . . 22

2.15 Corrosive environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

3.0 Configuring and mounting the drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3.1 Handling and static discharge precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

3.2 Breather filter hole precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3.3 Jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

3.3.1 Master/slave configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

3.3.2 Cable-select option . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

3.3.3 Ultra ATA/100 cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

3.4 Drive mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

4.0 ATA interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

4.1 ATA interface signals and connector pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

4.1.1 Supported ATA commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

4.1.2 Identify Device command. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

4.1.3 Set Features command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

4.1.4 S.M.A.R.T. commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

5.0 Maxtor support services . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

DiamondMax 21 PATA Product Manual, Rev. B i

ii DiamondMax 21 PATA Product Manual, Rev. B

List of Figures

Figure 1. Typical 5V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 2. Typical 12V startup and operation current profile . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 3. Breather filter hole location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Figure 4. Master/slave jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Figure 5. Ultra ATA cable connectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Figure 6. Mounting dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Figure 7. I/O pins and supported ATA signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

DiamondMax 21 PATA Product Manual, Rev. B iii

iv DiamondMax 21 PATA Product Manual, Rev. B

1.0 Introduction

This manual describes the functional, mechanical and interface specifications for the following Maxtor DiamondMax® 21 PATA model drives:

STM3320820A STM3250620A STM3200820A STM380215A

STM3300620A STM3250820A STM3160215A

These drives provide the following key features:

• 7,200-RPM spindle speed

• High instantaneous (burst) data transfer rates (up to 100 Mbytes per second) using Ultra DMA mode 5.

• Tunneling magnetoresistive (TMR) recording heads and EPRML technology, which provide the drives with increased areal density.

• State-of-the-art cache and on-the-fly error-correction algorithms.

• Full-track multiple-sector transfer capability without local processor intervention.

• Quiet operation.

• SeaTools diagnostic software performs a drive self-test that eliminates unnecessary drive returns.

• Support for S.M.A.R.T. drive monitoring and reporting.

• Support for Read Multiple and Write Multiple commands.

• Support for autodetection of master/slave drives that use cable select (CSEL).

DiamondMax 21 PATA Product Manual, Rev. B 1

2 DiamondMax 21 PATA Product Manual, Rev. B

2.0 Drive specifications

Unless otherwise noted, all specifications are measured under ambient conditions, at 25°C, and nominal power. For convenience, the phrases the drive and this drive are used throughout this manual to indicate the following drive models:

STM3320820A STM3250620A STM3200820A STM380215A

STM3300620A STM3250820A STM3160215A

2.1 Specification summary tables

The specifications listed in the following tables are for quick reference. For details on specification measurement or definition, see the appropriate section of this manual.

DiamondMax 21 PATA Product Manual, Rev. B 3

Table 1: Drive specifications summary for the 320 and 300 Gbyte models

Drive specification STM3320820A STM3300620A

Formatted Gbytes (512 bytes/sector)* 320 300

Guaranteed sectors 625,142,448 586,072,368

Heads 4 3

Discs 2

Bytes per sector 512

Default sectors per track 63

Default read/write heads 16

Default cylinders 16,383

Recording density 781 kbits/in max

Track density 145 ktrakcs/in avg.

Areal density 114.4 Gbits/in2 avg

Spindle speed 7,200 RPM

Internal data transfer rate 1,030 Mbits/sec max

Sustained data transfer rate 72 Mbytes/sec max

I/O data-transfer rate 100 Mbytes/sec max

ATA data-transfer modes supported PIO modes 0–4

Cache buffer 8 Mbytes 16 Mbytes

Height (max) 26.1 mm (1.028 inches)

Width (max) 101.6 mm (4.000 inches) +/- 0.010 inches

Length (max) 146.99 mm (5.787 inches)

Weight 635 grams 600 grams

Average latency 4.16 msec

Power-on to ready (max) 15 sec 11 s ec

Standby to ready (max) 15 sec

Track-to-track seek time (typical) <0.8 msec (read), <1.0 msec (write)

Average seek, read (typical) <11.0 msec

Average seek, write (typical) <12.0 msec

Startup current (typical) 12V (peak) 2.8 amps

Voltage tolerance (including noise) 5V ± 5%

Ambient temperature 0° to 60°C (operating)

Temperature gradient 20°C per hour max (operating)

Relative humidity 5% to 90% (operating)

Relative humidity gradient 30% per hour max

Wet bulb temperature (max) 37.7°C (operating)

Altitude, operating –60.96 m to 3,048 m

Altitude, nonoperating (below mean sea level, max)

Operational Shock 68 G at 2 msec

Non-Operational Shock 350 G at 2 msec

Multiword DMA modes 0–2 Ultra DMA modes 0–5

12V ± 10%

–40° to 70°C (nonoperating)

30°C per hour max (nonoperating)

5% to 95% (nonoperating)

37.7°C (nonoperating)

(–200 ft. to 10,000+ ft.)

–60.96 m to 12,192 m (–200 ft. to 40,000+ ft.)

4 DiamondMax 21 PATA Product Manual, Rev. B

Drive specification STM3320820A STM3300620A

Vibration, operating 5–22 Hz: 0.25 G, Limited displacement

Vibration, nonoperating 5–22 Hz: 0.25 G, Limited displacement

Drive acoustics, sound power (Bels)

Idle** 2.7 (typical)

Quiet seek 3.0 (typical)

Nonrecoverable read errors 1 per 10

Annualized Failure Rate (AFR) 0.34%

Warranty 3 years on distribution units.

Contact start-stop cycles 50,000 at 25°C, 50% rel. humidity

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment

and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and

power to operational levels.

22–350 Hz: 0.50 G 350–500 Hz:: 0.25 G

22–350 Hz: 5.0 G 350–500 Hz:: 1.0 G

3.0 (max)

3.4 (max)

bits read

To determine the warranty for a specific drive, use a web browser to access the following web page: From this page, click on the “Verify Your Warranty” link. You will be asked to provide the drive serial number, model number (or part number) and country of purchase. The sys tem will display the warranty information for your drive.

http://www.seagate.com/support/service/

2.5 (typical)

2.8 (max)

3.0 (typical)

3.1 (max)

DiamondMax 21 PATA Product Manual, Rev. B 5

Table 2: Drive specifications summary for 250 and 200 Gbyte models

Drive specification STM3250620A STM3250820A STM3200820A

Formatted Gbytes (512 bytes/sector)* 250 200

Guaranteed sectors 488,397,168 390,721,968

Heads 3

Discs 2

Bytes per sector 512

Default sectors per track 63

Default read/write heads 16

Default cylinders 16,383

Recording density 813 kbits/in max 781 kbits/in max

Track density 145 ktracks/in avg.

Areal density 114.4 Gbits/in2 avg

Spindle speed 7,200 RPM

Internal data transfer rate 1,030 Mbits/sec max

Sustained data transfer rate OD 72 Mbytes/sec max

I/O data-transfer rate 100 Mbytes/sec max

ATA data-transfer modes supported PIO modes 0–4

Cache buffer 16 Mbytes 8 Mbytes

Height (max) 26.1 mm (1.028 inches)

Width (max) 101.6 mm (4.000 inches) +/- 0.010 inches

Length (max) 146.99 mm (5.787 inches)

Weight (max) 600 grams

Average latency 4.16 msec

Power-on to ready (max) 11 sec

Standby to ready (max) 15 sec

Track-to-track seek time (typical) <0.8 msec (read), <1.0 msec (write)

Average seek, read (typical) <11.0 msec

Average seek, write (typical) <12.0 msec

Startup current (typical) 12V (peak) 2.8 amps

Voltage tolerance (including noise) 5V ± 5%

Ambient temperature 0° to 60°C (operating)

Temperature gradient 20°C per hour max (operating)

Relative humidity 5% to 90% (operating)

Relative humidity gradient 30% per hour max

Wet bulb temperature 37.7°C max (operating)

Altitude, operating –60.96 m to 3,048 m

Altitude, nonoperating (below mean sea level, max)

Operational Shock 68 G at 2 msec

Non-Operational Shock 350 G at 2 msec

Multiword DMA modes 0–2 Ultra DMA modes 0–5

12V ± 10%

–40° to 70°C (nonoperating)

30°C per hour max (nonoperating)

5% to 95% (nonoperating)

37.7°C max (nonoperating)

(–200 ft. to 10,000+ ft.)

–60.96 m to 12,192 m (–200 ft. to 40,000+ ft.)

6 DiamondMax 21 PATA Product Manual, Rev. B

Drive specification STM3250620A STM3250820A STM3200820A

Vibration, operating 5–22 Hz: 0.25 G, Limited displacement

Vibration, nonoperating 5–22 Hz: 0.25 G, Limited displacement

Drive acoustics, sound power (Bels)

Idle** 2.5 (typical)

Quiet seek 3.0 (typical)

Nonrecoverable read errors 1 per 10

Annualized Failure Rate (AFR) 0.34%

Warranty 3 years on distribution units.

Contact start-stop cycles 50,000 at 25°C, 50% rel. humidity

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment

and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and

power to operational levels.

22–350 Hz: 0.50 G 350–500 Hz:: 0.25 G

22–350 Hz: 5.0 G 350–500 Hz:: 1.0 G

2.8 (max)

3.1 (max)

bits read

http://www.seagate.com/support/service/

DiamondMax 21 PATA Product Manual, Rev. B 7

Table 3: Drive specifications summary for the 160 and 80 Gbyte model

Drive specification STM3160215A STM380215A

Formatted Gbytes (512 bytes/sector)* 160 80

Guaranteed sectors 312,581,808 156,301,488

Heads 2 1

Discs 1

Bytes per sector 512

Default sectors per track 63

Default read/write heads 16

Default cylinders 16,383

Recording density 824 kbits/in max

Track density 137.259 ktracks/in avg.

Areal density 101 Gbits/in2 avg

Spindle speed 7,200 RPM

Internal data transfer rate 930 Mbits/sec max

Sustained data transfer rate OD 78 Mbytes/sec max

I/O data-transfer rate 100 Mbytes/sec max

ATA data-transfer modes supported PIO modes 0–4

Cache buffer 2 Mbytes

Height (max) 19.99 mm (0.787 inches)

Width (max) 101.6 mm (4.000 inches) +/- 0.010 inches

Length (max) 146.99 mm (5.787 inches)

Weight (max) 380 grams 365 grams

Average latency 4.16 msec

Power-on to ready (max) 7.9 sec

Standby to ready (max) 7.9 sec

Track-to-track seek time (typical) <1.0 msec (read), <1.2 msec (write)

Average seek, read (typical) <11.0 msec

Average seek, write (typical) <12.0 msec

Startup current (typical) 12V (peak) 2.8 amps

Voltage tolerance (including noise) 5V ± 5%

Ambient temperature 0° to 60°C (operating)

Temperature gradient 20°C per hour max (operating)

Relative humidity 5% to 90% (operating)

Relative humidity gradient 30% per hour max

Wet bulb temperature 37.7°C max) (operating)

Altitude, operating –60.96 m to 3,048 m

Altitude, nonoperating (below mean sea level, max)

Operational Shock 63 G max at 2 msec

Non-Operational Shock 350 G max at 2 msec

Multiword DMA modes 0–2 Ultra DMA modes 0–5

12V ± 10%

–40° to 70°C (nonoperating)

30°C per hour max (nonoperating)

5% to 95% (nonoperating)

40.0°C max) (nonoperating)

(–200 ft. to 10,000+ ft.)

–60.96 m to 12,192 m (–200 ft. to 40,000+ ft.)

8 DiamondMax 21 PATA Product Manual, Rev. B

Drive specification STM3160215A STM380215A

Vibration, operating 5–22 Hz: 0.25 G, Limited displacement

Vibration, nonoperating 5–22 Hz: 0.25 G, Limited displacement

Drive acoustics, sound power (Bels)

Idle** 2.8 (typical)

Quiet seek 3.0 (typical)

Nonrecoverable read errors 1 per 10

Annualized Failure Rate (AFR) 0.34%

Warranty 3 years on distribution units.

Contact start-stop cycles 50,000 at 25°C, 50% rel. humidity

*One Gbyte equals one billion bytes when referring to hard drive capacity. Accessible capacity may vary depending on operating environment

and formatting.

**During periods of drive idle, some offline activity may occur according to the S.M.A.R.T. specification, which may increase acoustic and

power to operational levels.

22–350 Hz: 0.50 G 350–500 Hz:: 0.25 G

22–350 Hz: 5.0 G 350–500 Hz:: 1.0 G

3.0 (max)

3.2 (max)

bits read

http://www.seagate.com/support/service/

DiamondMax 21 PATA Product Manual, Rev. B 9

+ 35 hidden pages