Master-Bilt MBC40-4A, MBCF220 Owner’s Manual

3299720 / 160555

Rev.1 06/2015

BLAST CHILLERS/FREEZERS

CELLULES DE REFROIDISSEMENT RAPIDE/CELLULES MIXTES

ABATIDORES/CONGELADORES RAPIDOS DE TEMPERATURA

USE AND INSTALLATION MANUAL

MANUEL D’UTILISATION ET D’INSTALLATION

MANUAL DE USO E INSTALACIÓN

Carefully read the instructions contained in the handbook. You may find important safety instructions and recommendations for use and maintenance.

Please retain the handbook for future reference. The Manufacturer is not liable for any changes to this handbook, w hich may be altered without prior

notice.

Lire avec attention les instructions contenues dans ce livret car elles fournissent d'importants renseignements pour ce qui concerne la sécurité, l'emploi et l'entretien.

Garder avec soin ce livret pour des consultations ultérieures de différents opérateurs. Le constructeur se réserve le droit d'apporter des modifications à ce manuel, sans préavis ni

responsabilité d'aucune sorte.

Lea atentamente las advertencias contenidas en este manual pues dan importantes indicaciones concernientes la seguridad, la utilización y el mantenimiento del aparato.

Rogamos guarde el folleto de instalación y utilización, para eventuales futuros usuarios. El constructor se reserva el derecho de hacer modificas al actual manual, sín dar algún preaviso y sín

responsabilidad alguna.

3299720 /160555_GB

INDEX

GENERAL INSTRUCTIONS ON DELIVERY ....................................................................... 5

GENERAL WARNINGS .................................................................................................................................. 5

LIST OF RULES ............................................................................................................................................. 5

TRANSPORT AND HANDLING ....................................................................................................................... 5

UNPACKING ................................................................................................................................................ 5

GENERAL SAFETY WARNINGS ...................................................................................................................... 6

INSTALLATION ............................................................................................................ 7

PLATE DATA ................................................................................................................................................ 7

MAX ROOM TEMPERATURE ........................................................................................................................ 7

INSTALLATION ............................................................................................................................................. 8

DIMENSIONS .................................................................................................................................................................... 9

TECHNICAL DATA ............................................................................................................................................................ 10

WIRING ..................................................................................................................................................... 11

CONDENSATE DRAIN ................................................................................................................................. 11

TESTING .................................................................................................................................................... 11

CONTROL AND SAFETY SYSTEMS ............................................................................................................... 12

REFRIGERANT MATERIAL SAFETY DATA SHEET .......................................................................................... 12

DISPOSAL .................................................................................................................................................. 13

STERILIZATION LAMP INSTALLATION ......................................................................................................... 13

PRINTER INSTALLATION ............................................................................................................................ 13

OPERATION .............................................................................................................. 14

GENERAL DESCRIPTION ............................................................................................................................. 14

SETTING UP .................................................................................................................................................................... 14

MACHINE LOADING ........................................................................................................................................................ 15

POSITION OF TRAYS........................................................................................................................................................ 15

CORE PROBE ................................................................................................................................................................... 15

TEMPERATURES ............................................................................................................................................................. 16

LENGTH .......................................................................................................................................................................... 16

CONTROL PANEL ....................................................................................................................................... 17

FIRST START-UP ......................................................................................................................................... 18

PROGRAM ................................................................................................................................................. 19

PROGRAM DESCRIPTIONS .............................................................................................................................................. 19

STANDARD PROGRAMS .................................................................................................................................................. 21

PROGRAM I.F.R. ............................................................................................................................................................. 22

PROGRAM INFINITY ........................................................................................................................................................ 23

FAVORITE PROGRAMS .................................................................................................................................................... 24

AUTOMATIC PROGRAMS ............................................................................................................................................... 25

STORED PROGRAMS ....................................................................................................................................................... 27

MULTY ............................................................................................................................................................................ 29

COOLING ........................................................................................................................................................................ 30

FUNCTIONS ............................................................................................................................................... 31

DEFROST ......................................................................................................................................................................... 31

SANITATION.................................................................................................................................................................... 32

STORAGE ........................................................................................................................................................................ 33

THAWING ....................................................................................................................................................................... 34

PROVING (PROOFING) ................................................................................................................................................... 36

PROBE HEATING ............................................................................................................................................................. 38

** VIEW / EDIT PARAMETERS CYCLE .............................................................................................................................. 40

3299720 /160555_GB

HACCP ....................................................................................................................................................... 41

Name and Surname

Address

Tel./fax no.

SETTINGS .................................................................................................................................................. 50

LANGUAGE ..................................................................................................................................................................... 50

SET DATE/CLOCK ............................................................................................................................................................ 51

SECTOR ........................................................................................................................................................................... 52

MULTY ............................................................................................................................................................................ 53

CYCLE CONTROL - AUTO OR MANUAL ........................................................................................................................... 54

SERVICE ..................................................................................................................................................... 55

ALARMS .......................................................................................................................................................................... 55

ALARMS TABLE ............................................................................................................................................................... 56

RESET ALLARMI .............................................................................................................................................................. 57

INPUTS OUTPUTS ........................................................................................................................................................... 58

RESTORE ......................................................................................................................................................................... 59

PARAMETERS .................................................................................................................................................................. 60

MAINTENANCE ......................................................................................................... 61

MAINTENANCE AND CLEANING ................................................................................................................. 61

CLEANING THE CABINET ................................................................................................................................................. 61

CLEANING THE AIR CONDENSER .................................................................................................................................... 62

STAINLESS-STEEL MAINTENANCE ................................................................................................................................... 62

DISCONTINUED USE ....................................................................................................................................................... 63

EXTRAORDINARY MAINTENANCE .............................................................................................................. 63

VIDEO BOARD AND ENCODER MAINTENANCE CHECKLIST ............................................................................................ 63

MAINTENANCE OF PANEL BOARD .................................................................................................................................. 64

CONDENSING SYSTEM MAINTENANCE .......................................................................................................................... 65

REPLACEMENT CORE PROBE .......................................................................................................................................... 66

WIRING DIAGRAM PLATE .......................................................................................................................... 66

Annotate the emergency assistance number of specialised maintenance personnel.

3299720 /160555_GB

GENERAL INSTRUCTIONS ON DELIVERY

GENERAL WARNINGS

We assure you have made the best choice in purchasing our products and hope you will be fully satisfied with the performance. To this purpose, we recommend you strictly comply with the instructions and regulations contained in this handbook.. The user is required to carefully read the manual, always referring to it and conserving it in a known place, accessible to all operators. The equipment is destined only for the function for which it was designed and, being for professional use, must be used only by qualified personnel. The manufacturer declines all responsibility and any obligation to warranty if damage occurs to the equipment, persons or things, imputable to incorrect installation, inappropriate use by untrained personnel, non specific modifications or interventions, use of non original or non specific replacement parts, failure to observe, even partially, the indications found in this manual. Please remember that no reproductions of this handbook are allowed. Due to our constant technological updating and research, the features described in this handbook may be altered without prior notice.

LIST OF RULES

The cooling cabinet we manufacture fully complies with the following regulations: UL Listed for electrical safety – UL471 CSA C22.2.120

NSF standard 7 for sanitation

TRANSPORT AND HANDLING

For transportation and handling, all precautions necessary must be taken in order not to damage the equipment, referring to the indications found on the packaging of the same. Make sure that the consignment has not been tampered with or damaged during transport.

UNPACKING

Installation must be carried out by authorized personnel. After removing the packaging, ensure the integrity of the equipment and verify that all

the parts or components are present and that the characteristics and state correspond to the specifications of the your order. If not, please inform the retailer immediately.

Remove pvc protective film from all over the appliance.

Attention: all the packing material must be disposed of in accordance with the prevailing regulations in the country where the equipment is used and in any case must not be dispersed into the environment.

3299720 /160555_GB

GENERAL SAFETY WARNINGS

The user is responsible for operations carried out on the equipment which do not comply with the indications in this manual, and periodic training of all personnel to work on the equipment is recommended.

List of some general warnings:

- do not touch the equipment with moist or wet hands or feet

- do not insert screwdrivers or kitchen tools or anything else between the guards and the parts in motion

- before any cleaning or maintenance operation, disconnect the equipment from the electrical mains

- do not pull on the power cord to disconnect the machine from the electrical mains

- during loading/unloading of product in the equipment use kitchen gloves

- use the needle probe to read the temperature at the core of the product, making sure to handle it with care

3299720 /160555_GB

INSTALLATION

Model

Air q.ty

[cfm]

BC40A BCF48A BCF35A

BC80A BCF99A

2.060

PLATE DATA

Make sure the technical wiring specifications comply with the ratings (i.e., V, kW, Hz, no. phases and mains power).

Please quote the product's serial number (shown on the rating plate) on any enquiry to the Manufacturer.

List of rates shown on the rating plate:

1) Model

2) Manufacturer’s name and address

3) Insulation class

4) Year of production

5) Serial number

6) Electrical device casing protection rating A) Input voltage B) Electric current intensity C) Frequency D) Phase E) Compressor F) Compressor RLA G) Compressor LRA H) Defrost heater

I) Power defrost heater L) Condenser fan M) Condenser fan FLA N) Expanding fluid O) Refrigerant name P) Refrigerant quantity Q) Climatic class R) Fuse S) MCA T) Evaporator fan U) Evaporator fan FLA V) Design pressure W) High side pressure Z) Low side pressure

MAX ROOM TEMPERATURE

Air-condenser units should not operate if room temperature is over 100°F. Above 90°F maximum output is not guaranteed.

Min. air circulation

650

3299720 /160555_GB

INSTALLATION

The appliance must be installed and tested in full compliance with accident-prevention regulations contained in national law and current guidelines. Installers are to comply with any current local regulations.

 Place the appliance onto the required working site.

 Avoid locations with exposure to direct sunlight.  Do not place the appliance in hot, poorly-ventilated rooms.  Do not place the refrigerated compartment near heat sources.

 Leave a min. 4” clearance around the appliance on

the sides where air inlet and outlet are located.

 Level the appliance by means of adjustable feet.

WARNING: If the appliance is not properly levelled the performance and condensate drain may be hampered.

3299720 /160555_GB

DIMENSIONS

Please refer to the dimensions of your own appliance.

BC40A BCF48A

80 (3,15")

746,5 (29,38")

1407 (55,39")

720 (28,3")

BCF35A

690 (27,16")

150 (5,88")

82,5

(3,23")

(2,36")

740 (29,13)

150 (5,9")

56,5

(2,22")

(1,97")

(24,6")

(24,88")

929 (36,57")

210

(8,27")

760

(29,92")

625

632

340

(13,87")

(2,36")

56,5

(2,22")

(1,97")

(3,23")

82,5

970 (38,19")

61,7

(2,43")

840 (33,04")

103,3

(4,06")

600

(23,62")

535

(21,06")

783,5 (30,84")

650 (25,59")

510

(20,07")

135,9

(5,35")

1293,9 (50,94")

169,6

(6,67")

BC80A BCF99A

(2,95")

1710

(67,3")

150 (5,9")

(2,36")

800 (31,49")

650

(25,59")

680

(26,77")

(2,95")

(2,36")

1860

(73,23")

105,5

(4,15")

842,7 (33,17")

700 (27,56")

600

(23,62")

1562 (61,49")

125,3

(4, 93")

3299720 /160555_GB

Model

BC40A

BC80A

Gross weight [lb]

276

496

Net weight [lb]

254

440

Dimensions

29,38”x28,3”x38,19”

31,49”x33,17”x73,23”

Capacity

Mass /cycle [lb] (+194°Fy+37°F)

100

Net internal volume [cuft]

2,55

5,52

Grids

Power supply

Voltage [V]

220 ~

Frequency [Hz]

Phase

1 ph

3 ph

Intensity [A]

6,5

Power input [W]

1051

2972

Refrigerating unit

Refrigerating power [W]

1083

4152

Evaporation temperature [°F]

Cooling temperature [°F]

+194y+37

Cooling time [min]

Condensation temperature [°F]

+130

Max room temperature [°F]

+90

Compressor type

Ermetic

Refrigerant

R404A

Refrigerant qty [lb]

4,4

Condesation air

Air

Noise [dB] (A)

IFR

Multi-detector probe

Model

BCF48A

BCF35A

BCF99A

Gross weight [lb]

286

297

496

Net weight [lb]

264

440

Dimensions

29,38”x28,3”x38,19”

36,57”x33,04”x30,84”

31,49”x33,17”x73,23”

Capacity

Mass /cycle [lb] (+194°Fy+37°F)

100

Mass /cycle [lb] (+194°Fy0°F)

Net internal volume [cuft]

2,55

5,52

Grids

3 3 3

Power supply

Voltage [V]

220 ~

Frequency [Hz]

Phase

1 ph

3 ph

Intensity [A]

6 6 8,5

Power input [W]

1139

1122

2625

Refrigerating unit

Refrigerating power [W]

1054

3136

Evaporation temperature [°F]

-22

Cooling temperature [°F]

+194y+37

Cooling time [min]

Freezing temperature [°F]

+194y0

Freezing time [min]

240

Condensation temperature [°F]

+130

Max room temperature [°F]

+90

Compressor type

Ermetic

Refrigerant

R404A

Refrigerant qty [lb]

3 3 4,4

Condesation air

Air

Noise [dB] (A)

IFR

Multi-detector probe

TECHNICAL DATA

Please refer to the technical data of your own appliance.

3299720 /160555_GB

WIRING

The connection to power supply may be carried out at the back of the appliance after removing the protection grid.

All wiring cables are to comply with the ratings shown on the technical specifications

Cables are to be connected to the no potential difference terminal.

The grounding cable is to be directly connected to a good grounding system.

The guarantee will cease and the Manufacturer will not be liable for any damage to appliances or operators arising from the non-compliance with the and tamperings to any part of the appliance (electric, thermodynamic or hydraulic plant).

CONDENSATE DRAIN

The equipment has a condensation collection tray. The tray is extractable from the lower part of the equipment.

TESTING

Should the appliance have been transported horizontally instead of a vertical position DO NOT START THE APPLIANCE IMMEDIATELY. WAIT FOR AT LEAST 24 HOURS BEFORE OPERATING.

The manufacturer declines any responsibility and any warranty obligation if damage occurs to the equipment imputable to transportation in a horizontal position.

Carry out the following checkings:

1) Outside temperatures must be included between 59°F and 100°F.

2) Turn on the appliance and wait 30 minutes before the use if the external temperature is “low”.

3) Check power input

4) Carry out at least one full quick cooling cycle

3299720 /160555_GB

CONTROL AND SAFETY SYSTEMS

The following information concerns skilled staff only.

 Door micro-switch: Prevents the appliance from working when the door is open  Overall protection fuses: Protect the whole power circuit from and short-circuits and overloads  Compressor thermal relay: Operates in case of an overload or working failures  Motor-fan thermal relay: Operates in case of an overload or working failures  Safety pressure-switch: Operates in case of coolant over-pressure  Cabinet temperature control: Is run by NTC probe through the relevant electronic card  Core temperature control: Is run by PT100 probe through an electronic card  Electronic boards: based on the parameters entered they command and control any devices connected

to the equipment.

REFRIGERANT MATERIAL SAFETY DATA SHEET

1) R404a: fluid components

x trifluoroethane (HFC 143a) 52% x pentafluoroethane (HFC 125) 44% x tetrafluoroethane (HFC 134a) 4%

GWP = 3750 ODP = 0

2) Hazard identification

Overexposure through inhalation may cause anaesthetic effects. Acute overexposure may cause cardiac rhythm disorders and sudden death. Product mists or sprays may cause ice burns of eyes and skin.

3) First aid procedures

x Inhalation: keep injured person away from exposure, warm and relaxed. Use oxygen, if necessary. Give

artificial respiration if respiration has stopped or is about to stop. In case of cardiac arrest give external cardiac massage. Seek immediate medical attention

x Skin: use water to remove ice from affected areas. Remove contaminated clothes.

CAUTION: clothes may adhere to skin in case of ice burns. In case of contact with skin, wash with copious quantities of lukewarm water. In case of symptoms (irritation or blisters) seek medical attention.

x Eyes: immediately wash with ocular solution or fresh water, keeping eyelids open for at least 10 minutes.

Seek medical attention.

x Ingestion: it can cause vomit. If conscious, rinse mouth with water and drink 200-300 ml of water. Seek

medical attention

x Other medical treatment: symptomatic treatment and support therapy when indicated. Do not administer

adrenaline or sympatheticomimetic drugs after exposure, due to the risk of arrhythmia and possible cardiac arrest.

4) Environmental data

Persistence and degradation

x HFC 143a: slow decomposition in lower atmosphere (troposphere). Duration in atmosphere is 55 years. x HFC 125: slow decomposition in lower atmosphere (troposphere). Duration in atmosphere is 40 years. x HFC 134a: relatively rapid decomposition in lower atmosphere (troposphere). Duration in atmosphere is

15.6 years x HFC 143a, 125, 134a: does not affect photochemical smog (not included in volatile organic

components – VOC – as established in the UNECE agreement). Does not cause ozone rarefaction.

Product exhausts released in the atmosphere do not cause long-term water contamination.

3299720 /160555_GB

DISPOSAL

WASTE STORAGE

At the end of the product life, avoid release to the environment. The doors should be removed before disposal. Temporary storage of special waste is permitted while waiting for disposal by treatment and/or final collection. Dispose of special waste in accordance with the laws in force with regard to protection of the environment in the country of the user.

PROCEDURE FOR ROUGH DISMANTLING THE APPLIANCE

Countries have different legislation; provision laid down by the laws and the bodies of the countries where the demolition takes place are therefore to be observed. A general rule is to deliver the appliance to collection and demolition centers. Dismantle the refrigerator grouping together the components according to their chemical nature. The compressor contains lubricating oil and refrigerant, which may be recycled. The refrigerator components are considered special waste, which can be assimilated with domestic waste. Make the appliance totally unusable by removing the power cable and any door locking mechanisms in order to avoid the risk of anyone being trapped inside.

DISMANTLING OPERATIONS SHOULD BE CARRIED OUT BY QUALIFIED PERSONNEL. The improper disposal of Waste Electrical and Electronic Equipment is liable to punishment under

the relevant laws in the countries where the offence is committed. Waste electrical and Electronic Equipment may contain hazardous substances with potential harmful

effects on the environment and human health. You are urged to dispose of them properly.

STERILIZATION LAMP INSTALLATION

The sterilization lamp kit is not supplied as standard equipment.

Should you purchase the kit, please follow the installation instructions to install.

PRINTER INSTALLATION

The printer is not supplied as standard equipment .

Should you purchase the printer, please follow the installation instructions to install.

3299720 /160555_GB

OPERATION

Standard of

shelves

+194[°F]y+37[°F]

+194[°F]y0[°F]

n° max

BC40A

48[lb]

- 3 6

12“x20“

1,5“

BCF48A

48[lb]

28[lb] 3 6

12“x20“

1,5“

BCF35A

35[lb]

22[lb]

12“x20“

1,5“

BC80A

100[lb]

- 3 12

12“x20“

1,5“

BCF99A

100[lb]

60[lb]

12“x20“

1,5“

GENERAL DESCRIPTION

This unit is capable of reducing the internal temperature of the contents from 135°F (57°C) to 40°F (4°C) with in 4 hours, in order to conserve it for a long period of time without altering the organoleptic characteristics. Machine capacity as to the quantity to be cooled depend on the model purchased.

SETTING UP

Before setting to operation thoroughly clean the cooling cabinet with a suitable detergent or sodium bycarb dissolved in lukewarm water. Clean the appliance inside to remove any condensate caused by the Manufacturer's final testing.

Cooling and freezing speed depends on the following factors:

a) container shape, type and material; b) whether container lids are used; c) foodstuff features (density, water contents, fat contents); d) starting temperature; e) thermal conduction inside the foodstuffs.

Positive /Negative quick cooling time depends on type of foodstuffs to be processed. In general the programs the machine is equipped with are based on the chamber temperature management, the fan speed and the chilling time, in any case never exceed 7lb of load (for 12”x20” pans) or 15lb of load (for 18”x26” pans) and a thickness of 2” in negative chilling phase and 3” in positive chilling phase (table 2). Check that the positive chilling program, up to +37°F at the product core, does not take more than 90 minutes and that the negative chilling program, up to 0°F at the product core, does not take more than 4 hours. We recommend pre-chilling the work chamber before beginning with a chilling program and not covering the food during the program in order not to increase times. We recommend using the core probe in order to have the exact core temperature reading. Do not stop the cycle before reaching a temperature of +37°F during positive quick cooling and 0°F during negative quick cooling.

Tab.2

Model Max. output/cycle

Capacity h

3299720 /160555_GB

SINGLE-DETECTOR PROBE

MULTI-DETECTOR PROBE

PRODUCT CORE

PRODUCT SURFACE

MACHINE LOADING

Do not pile up foodstuffs to be cooled. Thickness should be lower than 2” in negative quick cooling and lower than 3” in positive quick cooling.

Make sure air circulation is not hampered between food trays.

The grid-holding frame (included in those models which include trolleys) is to be located at the centre of the cabinet.

POSITION OF TRAYS

Place the trays as close to the evaporator as possible.

If the cabinet is not full place the trays at equal distance from one another.

CORE PROBE

For proper position of the probe, refer to the following pictures.

SONDA A SING OLO RILEVAMENTO

SONDA A MULTIPLO RILEVAMENTO

0,19”-0,79”

SUPER FICIE PR OD OT TO

CUORE PRODOTTO

3299720 /160555_GB

TEMPERATURES

Do not leave the cooked products that are to be chilled/frozen at room temperature. Avoid humidity losses, which will be detrimental to the conserved fragrance of the product. We recommend beginning the chilling/freezing program as soon as the preparation or cooking phase has ended, being careful to insert the product into the equipment at a temperature no lower than +160°F. The cooked product can enter the equipment even at very high temperatures, greater than +212°F, as long as the chamber has been pre-chilled. In any case it should be taken into consideration that the program reference times always start from a temperature of +194°F, in positive chilling from +194°F to +37°F and in negative chilling from +194°F to 0°F.

LENGTH

Cooled or frozen processed foodstuffs may be stored in a refrigerator for 5 days of processing with no quality alterations. For best results we recommend keeping temperature constant throughout the

storing (32°F to 39°F), according to the various commodities. Storing time may be increased to approx. two weeks by using vacuum

processing. After a negative quick cooling cycle, foodstuffs may be stored safely for 3 to 18 months, according to the type of foodstuff processed. We strongly recommend keeping storing temperature at -4°F or below. The cooled product should be wrapped in a specific film for foodstuffs (better still, vacuum stored) and provided with a sticker reporting the content [A], date of processing [B] and expiry date [C] written in permanent type ink.

3299720 /160555_GB

D B C

CONTROL PANEL

The illustration shows the equipment control panel, while the list indicates the description and functionality of the individual commands.

SOFT+37°F

HARD +37°F IFR

SOFT 0 ° F HARD 0 ° F

INFINITY

A–Display: Displays all the information relative to the menus on the board and the application in progress. B–

HOME button: In any context, if enabled, this allows the user to return immediately to the main screen. If

the button is enabled this is indicated by the corresponding back lighting.

C–

BACK button: During navigation this button allows the user to return to the previous level in the menu

structure, while when any cycle is in progress, it allows the user to modify the control parameters of the process in progress, temporarily saving the modified values.

D–

Knob: The clockwise and anticlockwise turning of the knob allows the user to navigate through the

various menus on the display, while pressing it allows access to the selected item.

The RGB LED bar, built into the door handle, takes on a different color depending on the process in progress:

- Stand-by: low intensity steady light blue light

- Chilling/freezing cycle (including infinity, Multy) Defrost and Cooling, in progress: high intensity flashing

light blue light

- Conservation in progress: high intensity steady light blue light

- Freezing in progress: high intensity steady red light

- Sanitation in progress: low intensity steady red light

- Fault: steady yellow light

3299720 /160555_GB

1. Select LANGUAGE by rotating the knob

2. Press the knob to confirm the selected

1. Select the SECTOR by rotating the

2. Press the knob to confirm the selected

FIRST START-UP

At the first start-up the operator will be asked to choose the language and the sector.

LANGUAGE SETTING

ITALIA NO

DUTCH

DANSK

ENGLISH

SVENSKA

FRANCAIS DEUTSCH

NORSK

ESPAN OL

language

The language can also be changed later (see

page 50)

ITALIA NO

ENGLISH

FRANCAIS DEUTSCH

ESPAN OL

SECTOR SETTING

knob

sector

The sector can also be changed later (see page 52)

CATERING

PASTRY

BAKERY

ICE CR EAM

CATERING

PASTRY BAKERY ICE CR EAM

DUTCH DANSK SVENSKA

NORSK

3299720 /160555_GB

PROGRAM

DESCRIPTION

STANDARD PROGRAMS

Cycle carried out through probe at the core or time, suitable for chilling foods up to +37°F, using a chamber temperature of about

Cycle suitable for delicate products such as mousse, creams, desserts, vegetables or foods that are not very thick

Cycle carried out through probe at the core or time, suitable for chilling foods up to +37°F, using a chamber tem

Cycle suitable for very dense products, with high grease content or large sized products

I.F.R. is the patented positive blast chilling system that automatically optimises the process for any type of food, no matter the size and quantity, chilling its surface thanks to the use of a multipoint, three sensor needle probe

Cycle carried out through probe at the core or time, suitable for freezing foods up to 0°F, using a chamber temperature varying from

Cycle suitable for leavened products, baked or cooked foods that are not very thick

Cycle carried out through probe at the core or time, suitable for freezing foods up to 0°F, using a chamber temperature that can reach

Cycle suitable for raw or cooked, large size foods

Time chilling/freezing cycle with infinite duration, suitable for cooling various type food pans. The temperature at the core can be checked

AUTOMATIC PROGRAMS +37°F - CATERING

LASAGNE

Cycle dedicated to chilling of lasagne

SOUPS AND SAUCES

Cycle dedicated to chilling of soups and sauces

RICE AND PASTA

Cycle dedicated to chilling of rice and pasta

MEAT

Cycle dedicated to chilling of meat

FISH

Cycle dedicated to chilling of fish

COOKED VEGETABLES

Cycle dedicated to chilling of cooked vegetables

HOT PASTRY

Cycle dedicated to chilling of hot pastry products

DRY PASTRY

Cycle dedicated to chilling of dry pastry products

WALNUTS VEAL

Cycle dedicated to chilling of walnuts veal

AUTOMATIC PROGRAMS 0°F - CATERING

LASAGNE

Cycle dedicated to freezing of lasagne

SOUPS AND SAUCES

Cycle dedicated to freezing of soups and sauces

RICE AND PASTA

Cycle dedicated to freezing of rice and pasta

MEAT

Cycle dedicated to freezing of meat

FISH

Cycle dedicated to freezing of fish

COOKED VEGETABLES

Cycle dedicated to freezing of cooked vegetables

RAW VEGETABLES

Cycle dedicated to freezing of raw vegetables

PASTR Y

Cycle dedicated to freezing of pastry products

RAW FISH

Cycle dedicated to freezing of raw fish

SUSHI

Cycle dedicated to freezing of Sushi

It is a special blast freezing cycle that enables preventive and total food preservation and restoration. Once the probe reads

at the food core, the appliance will automatically

start the "devitalization phase for 24 hours”

it is a special blast freezing cycle that enables preventive and total food preservation and restoration. Once the probe reads

at the food core, the appliance will automatically

start the "devitalization phase for 15 hours”

It is a special blast freezing cycle that enables preventive and total food preservation and restoration. Once the probe reads

at the food core, the appliance will automatically

start the "devitalization phase for 24 hours”

PROGRAM

PROGRAM DESCRIPTIONS

SOFT +37°F

HARD +37°F

IFR

SOFT 0°F

HARD 0°F

INFINITY

34°F.

perature varying from 5°F to 34°F.

34°F to -40°F.

-40°F.

ANISAKIS 24h*

ANISAKIS 15h*

OPISTORKIS 24h

* Tested and validated in cooperation with: University of Naples Federico II - Department of Zootechnical Sciences and Food inspection and the University Research laboratory at the wholesale fish market of Pozzuoli, Naples

-4°F

-31°F

-4°F

3299720 /160555_GB

AUTOMATIC PROGRAMS +37°F - PASTRY SHOP

DOUGH SHEETING

Cycle dedicated to chilling of sheet dough

MIXING IN DIE

Cycle dedicated to chilling of moulded dough

CREAM

Cycle dedicated to chilling of creams

LEAVENED

Cycle dedicated to chilling of leavened products

LEAVENED +50°F

Cycle dedicated to chilling of leavened products +50°F

SHORT PASTRY

Cycle dedicated to chilling of shortcrust dough

STUFFED PRODUCTS

Cycle dedicated to chilling of filled products

TARTS

Cycle dedicated to chilling of tarts

BRIOCHE

Cycle dedicated to chilling of brioche

PANNA COTTA

Cycle dedicated to chilling of panna cotta

YOGURT BOX

Cycle dedicated to preparing of yogurt

AUTOMATIC PROGRAMS 0°F - PASTRY SHOP

DOUGH SHEETING

Cycle dedicated to freezing of sheet dough

MIXING IN DIE

Cycle dedicated to freezing of moulded dough

TARTS

Cycle dedicated to freezing of tarts

MOUSSE

Cycle dedicated to freezing of mousse

CROISSANT

Cycle dedicated to freezing of croissants

ICE CREAM

Cycle dedicated to freezing of ice cream

AUTOMATIC PROGRAMS +37°F - BAKERY

TARTS

Cycle dedicated to chilling of tarts

BAKED BREAD

Cycle dedicated to chilling of baked bread

CREAM

Cycle dedicated to chilling of creams

LEAVENED

Cycle dedicated to chilling of leavened products

AUTOMATIC PROGRAMS 0°F - BAKERY

COOKED TARTS

Cycle dedicated to freezing of baked tarts

RAW TARTS

Cycle dedicated to freezing of unbaked tarts

BAKED BREAD

Cycle dedicated to freezing of baked bread

UNCOOKED BREAD

Cycle dedicated to freezing of unbaked bread

AUTOMATIC PROGRAMS +37°F - ICE CREAM PARLOUR

PANNA COTTA

Cycle dedicated to chilling of panna cotta

YOGURT BOX

Cycle dedicated to preparing of yogurt

AUTOMATIC PROGRAMS 0°F - ICE CREAM PARLOUR

ICE CREAM -7°F

Cycle dedicated to freezing of ice cream -7°F

ICE CREAM

Cycle dedicated to freezing of ice cream

COMPLETE MOUSSE

Cycle dedicated to freezing of complete mousse

MOUSSE

Cycle dedicated to freezing of mousse

FROZEN DESSERT

Cycle dedicated to freezing of frozen dessert

MULTY PROGRAM

Time chilling/freezing cycle, organized by load levels, with possibility of needle probe reading, providing the time for each level

BANQUETING PROGRAM

BANQUETING

Cycle dedicated to the catering sector, excellent for preparation of banqueting products

VACUUM PROGRAM

Cycle dedicated to the catering sector for preparation of products before a vacuum-packing phase

THAWING PROGRAM

Cycle carried out by means of temperature probe or by time, dedicated to controlled food defrosting

PROVING PROGRAM

PROVING (PROOFING)

Time cycle, dedicated to direct leavening of foods

RETARDER PROVING

Time cycle, dedicated to scheduled leavening of foods

SMART ON PROGRAM

Cycle with automatic start. Once a hot product is inserted if an increase in the chamber temperature is detected, after 5 minutes a Soft

cycle will start, either by probe or time, based on whether or not the

needle is used.

MULTY

VACUUM

THAWING

SMART ON

+37°F

3299720 /160555_GB

1. Select the desired cycle by rotating the

2. Press the knob to activate the selected

3. Cycle ended, automatic conservation

If not required, manual defrosting is not performed

STANDARD PROGRAMS

Chilling/freezing cycles pre-set by the manufacturer which can be activated by selecting them directly from the initial screen, SOFT +37°F, HARD +37°F, SOFT 0°F and HARD 0°F. During execution of the cycle the parameters can be viewed and modified temporarily. The new values will be valid exclusively for the cycle in progress.

knob

cycle During the cycle it is possible:

- to view and modify the default parameters by selecting SET (see page 40)

- to stop the cycle by selecting STOP

Note: the modified parameters will be saved only for the cycle in progress

phase During conservation it is possible:

- to view and modify the default parameters by selecting SET (see page 40)

- to activate a manual defrost by selecting

- to stop the cycle by selecting STOP

Note: the modified parameters will be saved only for the cycle in progress.

SOFT +37°F

HARD +37°F

IFR

SOFT +37°F

HARD +37°F

IFR

90'

100%

HARD +37°F

SET STOP

END CYCLE

CONSERVE

SET STOP

SOFT 0°F

HARD 0°F

INFINITY

SOFT 0°F HARD 0°F

INFINITY

+80°F

+75°F

+80°F

+75°F

3299720 /160555_GB

1. Select the desired cycle by rotating the

2. Press the knob to activate the selected

Note: the modified value will only be saved for the

3. Cycle ended, automatic conservation

performed

PROGRAM I.F.R.

The IFR is an innovative patented system of positive quick cooling which allows the cycle optimized for each type of foodstuffs by preventing superficial freezing. Temperatures are detected by a three-sensor multipoint needle probe. The position inside the foodstuff is determined univocally by a reference disk located along the needle. (ref. par. “Core probe”).

knob

cycle

During the cycle it is possible:

- select SET to change the fan speed

- to stop the cycle by selecting STOP

cycle in progress

phase During conservation it is possible:

- to view and modify the default parameters by selecting SET (see page 40)

- to activate a manual defrost by selecting

- to stop the cycle by selecting STOP

Note: the modified parameters will be saved only for the cycle in progress. If not required, manual defrosting is not

SOFT +37°F HARD +37°F

IFR

SOFT +37°F HARD +37°F

IFR

100%

IFR

SET STOP

END CYCLE

CONSERVE

SET STOP

SOFT 0°F

HARD 0°F

INFINITY

SOFT 0°F HARD 0°F

INFINITY

+80°F

+75°F

+80°F

+75°F

3299720 /160555_GB

1. Select the desired cycle by rotating the

4. Cycle ended, automatic conservation

PROGRAM INFINITY

Time chilling/freezing cycle with infinite duration, suitable for cooling various type food pans. The temperature at the core can be checked.

knob

phase During conservation it is possible:

- select SET to view and modify the chamber

SOFT +37°F HARD +37°F

IFR

SOFT +37°F HARD +37°F

IFR

temperature and fan speed

- to stop the cycle by selecting STOP

Note: the modified values will be saved

INFINITY

100%

SET STOP

SOFT 0°F

HARD 0°F

INFINITY

SOFT 0°F

HARD 0°F

INFINITY

+80°F

+75°F

3299720 /160555_GB

2. Press the knob to enter section

3. Select the desired cycle by rotating the

4. Press the knob to activate the selected

5. Cycle ended, automatic conservation

If not required, manual defrosting is not performed

FAVORITE PROGRAMS

A library consisting in 10 cycles selected from those stored and labelled as favorites

Select by rotating the knob

SOFT +37°F

HARD +37°F

IFR

SOFT 0°F

HARD 0°F

INFINITY

(see page 27)

FAVORITE PROGRAMS

knob

cycle During the cycle it is possible:

- to view and modify the default parameters by selecting SET (see page 36)

- to stop the cycle by selecting STOP

Note: the modified parameters will be saved only for the cycle in progress

phase During conservation it is possible:

- to view and modify the default parameters by selecting SET (see page 40)

- to activate a manual defrost by selecting

- to stop the cycle by selecting STOP

SOFT +37°F HARD +37°F

IFR

1 CICLO 1 2 CICLO 2

CICLO 3

4 CICLO 4

1 CICLO 1 2 CICLO 2

CICLO 3

3 4 CICLO 4

90'

100%

MEMO +37°F

CICLO 3

SET STOP

MEMO +37°F

END CYCLE

CONSERVE

SET STOP

SOFT 0°F HARD 0°F

INFINITY

+80°F

+75°F

+80°F

+75°F

Note: the modified parameters will be saved only for the cycle in progress.

3299720 /160555_GB

1. Select MENU by rotating the knob

2. Press the knob to enter section MENU

SOFT 0°F

HARD 0°F

IFR INFINITY

SOFT +37°F HARD +37°F

3. Select AUTOMATIC by rotating the

4. Press the knob to enter section

5. Select the type of desired cycle by

6. Press the knob to enter into the

7. Select the desired cycle by rotating the

8. Press the knob to activate the selected

9. Select the quantity of load to be treated,

AUTOMATIC PROGRAMS

These programs are manufacturer recommended work cycles. During the cycle the parameters can be viewed, but not modified.

knob

AUTOMATIC

rotating the knob

SOFT +37°F HARD +37°F IFR INFINITY

AUTOM ATIC

STORED MULTY COOLIN G

AUTOM ATIC

STORED MULTY COOLIN G

AUTOM ATIC +37°F

AUTOM ATIC 0°F

BANQUETING

VACUUM

FUNCT IONS HACCP SETTING SERVICE

SOFT 0°F

HARD 0°F

MENU AUTO

selected type of cycle

knob

cycle

minimum, medium, maximum

AUTOM ATIC +37°F

AUTOM ATIC 0°F BANQUETING VACUUM

LASAGNE SOUPS AND SAUCES

RICE AND PASTA

MEAT

LASAGNE SOUPS AND SAUCES

RICE AND PASTA

MEAT

MENU AUTO

AUTO + 37°F

AUTO

AUTO + 37°F

RICE A ND

PASTA

3299720 /160555_GB

10. Press the knob to activate the selected

12. Cycle ended, automatic conservation

If not required, manual defrosting is not performed

cycle During the cycle it is possible:

- to view the default parameters by selecting INFO

- to stop the cycle by selecting STOP

RICE A ND

PASTA

Note: the parameters cannot be modified

45'

RICE AND

90%

INFO STOP

phase During conservation it is possible:

- to view the default parameters by selecting INFO

- to activate a manual defrost by selecting

- to stop the cycle by selecting STOP

Note: the parameters cannot be modified.

END CYCLE

CONSERVE

100%

SET STOP

AUTO +37°F

PASTA

+80°F

+75°F

+80°F

+75°F

3299720 /160555_GB

1. Select MENU by rotating the knob

2. Press the knob to enter section MENU

3. Press the knob to enter section

4. Press the knob to enter section

5. Select the type of desired cycle by

6. Press the knob to enter into the

7. Select the desired cycle by rotating the

8. Press the knob to activate the selected

t parameters and make

Note: the modified parameters can be saved once

will be active only for the cycle in progress.

STORED PROGRAMS

These are 10 chilling cycles and 10 freezing cycles that can be configured based on the needs of the user, the names of which can be freely set. These cycles already have default settings set up by the manufacturer: once modified by the user the new values can be saved in the memory and recalled at a subsequent start of that cycle. 10 of these programs can be made FAVORITES, organizing them based on the needs of the user.

STORED

rotating the knob

SOFT +37°F HARD +37°F IFR INFINITY

SOFT +37°F HARD +37°F

IFR INFINITY

AUTOM ATIC

STORED

MULTY COOLIN G

AUTOM ATIC

STORED

MULTY COOLIN G

STORED +37°F

STORED 0 °F

FUNCT IONS HACCP SETTING SERVICE

SOFT 0°F

HARD 0°F

SOFT 0°F

HARD 0°F

STORED

selected type of cycle

knob

cycle During the cycle it is possible:

- View, modify the defaul it a favorite by selecting SET

- to stop the cycle by selecting STOP

the new value is inserted by selecting otherwise, by selecting

, the modifications

STORED +37°F

STORED 0 °F

1 CICLO 1 2 CICLO 2

CICLO 3

4 CICLO 4

1 CICLO 1 2 CICLO 2

CICLO 3

3 4 CICLO 4

STORED

STOR.+37°F

STORED

STO R.+37°F

3299720 /160555_GB

If the modifications are saved the user will be asked to assign a name to the cycle. use the knob

list, and enter the desired position. The cycle will

9. Cycle ended, automatic conservation

View, modify the default parameters and make

Note: the modified parameters can be saved once

he modifications will

asked to assign a name to the cycle. use the knob

If not required, manual defrosting is not performed

END CYCLE CONSERVE

100%

+80°F

+75°F

SET STOP

STOR. + 37°F

to enter the name and press to save it. To make a cycle a favorite, select MAKE

FAVORITE, found at the end of the parameters automatically overwrite the one in that position.

Save by selecting

phase During conservation it is possible:

it a favorite by selecting SET

- to activate a manual defrost by selecting

- to stop the cycle by selecting STOP

the new value is inserted by selecting otherwise, by selecting t

be active only for the cycle in progress. If the modifications are saved the user will be

90'

100%

SET STOP

SOFT PHASE TIME SOFT PHASE FAN STORAGE

MAKE FAVORITE

STOR. + 37°F

CICLO 3

70%

39°F

+80°F

+75°F

60'

to enter the name and press to save it.

3299720 /160555_GB

1. Select MENU by rotating the knob

2. Press the knob to enter section MENU

3. Select MULTY by rotating the knob

4. Press the knob to enter section MULTY

5. Enter the time for each level and

to view and modify the default parameters by

At the expiry of the set value for each

to view and modify the default parameters by

Note: the modified parameters will be saved

MULTY

Chilling/freezing cycle by time organized by load levels. The number of levels available varies depending on the equipment.

confirm it with the knob During the cycle it is possible:

selecting SET (see page 40)

- to stop the cycle by selecting

Note: the modified parameters will be saved

+80°F

+75°F

SOFT 0°F

HARD 0°F

SOFT 0°F

HARD 0°F

MULTY

SOFT +37°F HARD +37°F IFR INFINITY

AUTOM ATIC STORED

MULTY

COOLIN G

AUTOM ATIC

STORED

MULTY

COOLIN G

1 30'

3 0'

4 0'

5 0'

FUNCT IONS HACCP SETTING SERVICE

FUNCT IONS

HACCP SETTING SERVICE

20'

SET

individual level, the buzzer and the flashing value alert the user that the product can be withdrawn.

Once all the set times have expired, automatic conservation phase During conservation it is possible:

selecting SET (see page 40)

1 30'

3 0' 4 0' 5 0'

20'

SET

+80°F

+75°F

MULTY

3299720 /160555_GB

1. Select MENU by rotating the knob

2. Press the knob to enter section MENU

3. Select COOLING by rotating the knob

4. Press the knob to activate the selected

5. Cycle ended, automatic conservation

for the cycle in progress

COOLING

It is advisable to run a cooling cycle prior to selecting any chilling cycle.

cycle During the cycle it is possible:

- to view and modify the default parameters by selecting SET (see page 40)

- to stop the cycle by selecting STOP

Note: the modified parameters will be saved only for the cycle in progress

SOFT +37°F

HARD +37°F IFR INFINITY

SOFT +37°F HARD +37°F

IFR INFINITY

AUTOM ATIC STORED MULTY

COOLIN G

AUTOM ATIC STORED MULTY

COOLIN G

100%

FUNCT IONS HACCP SETTING SERVICE

FUNCT IONS

HACCP SETTING SERVICE

COOLING

SET STOP

SOFT 0°F

HARD 0°F

SOFT 0°F

HARD 0°F

+80°F

+75°F

phase During conservation it is possible:

- to view and modify the default parameters by selecting SET (see page 40)

- to stop the cycle by selecting STOP

Note: the modified parameters will be saved only

END CYCLE

CONSERVE

100%

SET STOP

+80°F

+75°F

+ 164 hidden pages