Margaritaville DM2000-000-000 Owner's Manual

Fj
Fj
  B  Mrgts Cm Fr Mrgtvl
FROZEN CONCOCTION MAKER
  B  Mrgts Cm Fr Mrgtvl
®
®
Model DM2000 Series User Manual
IMPORTANT SAFEGUARDS
WHEN USING ELECTRICAL APPLIANCES, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:
1. READ ALL INSTRUCTIONS BEFORE USING.
2. To protect against electric shock, do not immerse appliance, cord or plug in water or other liquids.
3. Close supervision is necessary when any appliance is used near children. This appliance should not be used by children.
4. Unplug from outlet when not in use, before putting on or taking off parts, and before cleaning.
5. Avoid contacting moving parts.
6. Do not operate any appliance with damaged cord or plug or after the appliance malfunctions, or is dropped or damaged in any manner. Return appliance to the nearest authorized service facility for examination, repair or electrical or mechanical adjustments. Contact 1-877-689-2737 for customer service.
7. Do not use outdoors.
8. Do not let cord hang over the edge of a table or counter, or touch hot surfaces, including the stove.
9. Keep hands and utensils out of container while blending and/or ice shaving to reduce risk of severe injury to persons or damage to the unit. A rubber spatula may be used but must be used only when the appliance is not running.
10. Blades are sharp; handle carefully.
11. Always operate appliance with Jar Lid and Ice Reservoir Lid
in place.
12. The use of attachments not recommended or sold by the
manufacturer may cause fi re, electric shock or injury.
13. Do not use broken, chipped, or cracked Blending Jar or
Ice Reservoir.
14. To reduce risk of injury to persons, never place blending blade
assembly on base without the Glass Blending Jar properly attached.
15. Do not leave appliance unattended while it is operating.
16. To disconnect, turn control to off, then remove plug from
wall outlet.
17. Do not use appliance for other than intended use.
18. Never place fi ngers or other utensils into feed or
discharge areas.
19. Check Ice Reservoir for presence of foreign objects
before using.
20. Be certain the Jar Lid and Ice Reservoir Lid are securely
locked in place before operating appliance.
21. Do not blend hot liquids.
NOTE: NEVER SHAKE OR REMOVE BLENDER JAR DURING
OPERATION AS JAR BLADE ASSEMBLY CAN GET DAMAGED.
SAVE THESE INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
Polarized Plug
This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit in a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
-1-
Welcome
Cngrlis  r rch  t Mrgtvl®
Fro Cnco i Mkr® – DM2000 Si !
To learn more about Margaritaville® products,
please visit us at www.margaritavillecargo.com.
Frozen Concoction
Maker
PARTS LIST
1 Ice Reservoir Lid – Covers the Ice Reservoir.
2 Ice Reservoir – Holds the ice for making
frozen drinks.
3 Shaving Paddle – Moves ice across the
Shaving Blade.
4 Ice Hopper (ice defl ector blade assembly) –
Feeds ice from reservoir to Shaving Blade.
5 Ice Shaving Blade with defl ector – Shaves ice.
6 U-Lock – Holds Shaving Blade in place.
7 Ice Chute – Directs ice from Ice Hopper into
Blending Jar.
8 Blending Base – Holds Blending Jar securely
in place.
9 Control Panel – Contains all necessary controls to
operate your unit.
®
5
1
2
3
4
6
7
-2-
8
9
10 On/Off Switch.
11 Jar Lid – Seals the blending jar.
12 Blending Jar – Maximum capacity of 36 oz.
13 Blending Blade Sealing Ring – Seals the blending jar and blending base.
14 Blending Blade – Creates forward action when blending drinks.
15 Jar Base – Designed with wide base for stability.
11
12
13
16 Ice Reservoir Release Button – Releases ice
reservoir from unit.
17 Ice Melt Reservoir – Contains melted ice excess.
18 Cord Storage Door – Covers power cord
storage area.
O
I
10
14
15
16
17
18
-3-
Fiji™ DM2000 Series – Control Panel
c
7
È
Z
a
Z
G^iVh
9V^fj^g^h
Ha^YZh
Hbddi]^Zh
1
k
c
V
Y
]
H
3 4 5 6
2
1 Drink Selector Rotary Switch – Selects
from 4 different types of drinks.
Ritas – liquid ingredients only
– liquid ingredients
+ frozen fruit
Slides – liquid ingredients
+ ice cream
– liquid ingredients
+ fresh fruit
2 Shave ’n Blend™ Toggle Switch – Used
to select automatic Shave ’n Blend cycle.
Z
D
k
c
V
a
]
n
H
7
n
a
a
Z
c
c
D
Y
3 Power Indicator Light – Blinks when
unit is plugged in to indicate ready for use.
4 Progress Indicator Lights – Shows
status of Shave ’n Blend cycle.
5 Blend Only/Shave Only Toggle Switch –
Used to manually operate ice shaver and blender.
6 Number of Drinks Rotary Switch – used
to select 1, 2 or 3 twelve oz. frozen drinks.
-4-
Making frozen
drinks
Place the unit on a clean dry fl at surface.
1.
2. Place the Ice Reservoir on the unit front fi rst, then
push down fi rmly on back. Reservoir must click into place.
NOTE: IF ICE RESERVOIR IS NOT SEATED FIRMLY
IN PLACE THE UNIT WILL NOT OPERATE.
3. Remove the Cord Storage Door by pushing down on
the release tab located on the Cord Storage Door. Remove the power cord and plug the unit into a standard 120 Volt wall socket. Replace the cord storage door and position the power cord in the slot below the cord storage release tab.
4. Remove the Ice Reservoir Lid using the Release Button
located on the top of the Ice Reservoir.
Figr 1
Figr 2
Figr 3
Figr 1
Figr 2
NOTE: NEVER PUT ANYTHING BUT ICE IN
THE ICE RESERVOIR.
5. Fill the Ice Reservoir with ice cubes. Figr 4
6. Replace the Ice Reservoir Lid and snap closed.
7. Lift and remove the Blending Jar. The Ice Chute is
spring-loaded and can be pushed up.
8. Remove Blending Jar Lid.
9. Add appropriate amount of ingredients to the
Blending Jar for the number of drinks being made (1, 2 or 3).
Figr 3
Figr 4
-5-
For best results, use ice that has been out
of the freezer between 10 to 15 minutes.
The Best Margarita Recipe – “Ritas”
Amount (12 fl uid oz drink)
1 Drink 2 Drinks 3 Drinks
Ingredients
oz ml fl oz ml fl oz ml Margaritaville® Gold Tequila 11⁄3 40 2 2⁄3 80 4 120 Triple Sec Lime Juice Orange Juice Margaritaville® Margarita Mix 11⁄3 40 2 2⁄3 80 4 120
1
3 10 2⁄3 20 1 30
2
3 20 1 1⁄3 40 2 60
2
3 20 1 1⁄3 40 2 60
The Best Daiquiri Recipe – “Daiquiris”
Amount (12 fl uid oz drink)
1 Drink 2 Drinks 3 Drinks
Ingredients
oz ml fl oz ml fl oz ml Light Rum 1.5 45 3 90 4.5 135 Sugar 1Tbs 15 2Tbs 30 3Tbs 45 Cranberry Juice 3 90 6 180 9 270 Frozen Strawberries
The Best Slide Recipe
1 Drink 2 Drinks 3 Drinks
Ingredients
oz ml fl oz ml fl oz ml Bailey’s Irish Cream 11⁄3 40 22⁄3 80 42⁄3 140 Kahlua 11⁄3 40 22⁄3 80 42⁄3 140 Vanilla Ice Cream 4Tbs 59 8Tbs 118 14Tbs 207 Chocolate Syrup
2
3C 157 11⁄3C 315 2C 473
– “Slides”
Amount (12 fl uid oz drink)
2
3 20 11⁄3 40 21⁄3 70
The Best Smoothie Recipe
– “Smoothies”
Amount (12 fl uid oz drink)
1 Drink 2 Drinks 3 Drinks
Ingredients
oz ml fl oz ml fl oz ml Raspberry Sherbert
Ice Cream 4Tbs 59 8Tbs 118 12Tbs 177 Pineapple Juice 3 90 6 180 9 270 Fresh Strawberries
C = cups Tbs = tablespoons
1
2C 118 1C 236 11⁄2C 355
-6-
10.
Replace Blending Jar Lid and return Blending
Jar to Blending Base by pushing up on the Ice Chute with the Blending Jar and then placing it on the Blending Base.
11. Set the Number of Drinks Rotary Switch to
correspond to the number of drinks being made.
12. Select the type of drink to be made by turning
the drink selector rotary switch to the desired setting.
13. Turn the ON/OFF switch (located at the right side of unit) to the ON position.
NOTE: NEVER SHAKE OR REMOVE JAR DURING OPERATION –
BLADE ASSEMBLY WILL GET DAMAGED.
G^iVh
9V^fj^g^h
Ha^YZh
Hbddi]^Zh
Drink Selection
Rotary Switch
c
È
7
Z
k
a
Z
V
c
]
Y
H
Z
D
k
c
V
]
a
n
H
n
7
a
a
c
Z
D
c
Y
Number of Drinks
Rotary Switch
-7-
FIJI™ DM2000 SERIES
Automated Shave ’n Blend™ Cycle
14. Start the automatic shave and blend cycle
by pushing up on the Shave ’n Blend™ Toggle Switch.
G^iVh
9V^fj^g^h
Ha^YZh
Hbddi]^Zh
15. The unit will shave ice for the appropriate
time (based on the Number of Drinks Rotary Switch setting – and drink selection type. The blender will start automatically. The unit will stop at the completion of the cycle.
NOTE: DURING THE SHAVE AND BLEND CYCLE
THE PROGRESS INDICATOR LIGHTS WILL ILLUMINATE IN A SEQUENCE FROM LEFT TO RIGHT TO INDICATE THE CYCLE PROGRESS. DO NOT REMOVE THE BLENDING JAR WHILE THE PROGRESS INDICATOR LIGHTS ARE ILLUMINATED.
16. The Power Indicator Light will blink to indicate the unit
is ready to make more drinks.
17. To serve:
a. Lift and remove the Blending Jar. b. Remove Blending Jar Lid. c. Pour and enjoy.
DM2000 SERIES
c
È
7
Z
k
a
Z
V
c
]
Y
H
Shave ’n Blend™
Toggle Switch
FIJI™
NOTE: TO REMOVE EXCESS ICE FROM THE
ICE RESERVOIR HOLD THE SHAVE ONLY TOGGLE SWITCH IN THE SHAVE ONLY POSITION UNTIL THE ICE RESERVOIR IS EMPTY. WARNING: DO NOT PLACE FINGERS IN THE ICE HOPPER THE SHAVING BLADE IS SHARP AND COULD CAUSE INJURY.
18. Turn off the unit.
19. Periodically check the Ice Melt reservoir
and empty as needed.
-8-
Manual Cycle
To make a thicker drink:
a. Hold the “Blend Only/Shave Only” Toggle Switch
in the Shave Only position to add more ice to the
Blending Jar. b. To stop adding ice, release the toggle switch. c. To mix the newly added ice into the drink, hold
the Blend Only/Shave Only Toggle Switch in the
blend only position until the desired consistency
is achieved. To stop the blending release the
toggle switch. d. Use less drink mixer than in recipe.
(example: for 3 drinks, use 9 oz. liquid content)
To make a thinner drink:
a. Hold the Blend Only/Shave Only Toggle Switch in the
Blend Only position until the desired consistency is
achieved. b. To stop blending release the toggle switch. c. Add more drink mixer than in recipe
(example: for 3 drinks, use 10.5 oz. of total mix)
DM2000
Z
D
k
c
V
]
a
n
H
n
7
a
a
c
Z
D
c
Y
Blend Only/
Shave Only
Toggle Switch
-9-
Cleaning and
Maintenance
IMPORTANT: Your Blending Jar, Shaving and Blending Blades are subject to wear during normal use. Always inspect for nicks, chips, or cracks. Always inspect for broken, cracked, or loose blades. If the jar or Shaving and Blending Blades are damaged, do not use. Call our toll-free customer service number, 1-877-689-2737, to obtain replacement parts.
1. Make sure unit is unplugged. Place on a clean dry
surface. Turn the unit so the back is facing you. Push down on the Ice Reservoir Release Button. Lift the back of the Ice Reservoir and remove. This will expose the Shaving Paddle and Ice Hopper.
Note the location of the Shaving Blade inside the Ice Hopper.
WARNING: DO NOT PLACE FINGERS INSIDE THE ICE HOPPER NEAR THE SHAVING BLADE. BLADE IS SHARP HANDLE CAREFULLY.
Figr 2
2. To Remove the Shaving Paddle: Press the button
located behind the Ice Chute. If the button cannot be pressed, rotate the Shaving Paddle for a half turn and retry.
While pressing the button
Shaving Paddle counter-clockwise (to the left) by placing fi ngers in the ridges of the Shaving Paddle and unscrew. This will expose the Ice Hopper and Shaving Blade.
Figr 4
To re-assemble the Shaving Paddle, simply replace it
into the threaded insert and rotate clockwise. Hand tighten only.
3. Press the two Ice Hopper release catches and lift the
Ice Hopper to remove.
Remove the ice defl ector blade assembly by pushing
4.
and sliding the u-lock upwards. Pull the ice defl ector blade from the ice hopper and store in a safe place.
Figr 4
Figr 5
Figr 1
Figr 1
SHAVING BLADE
Figr 2
(Figr 3), rotate the
Figr 3
-10-
Figr 4
BE SURE TO RINSE THE SHAVING BLADE AND DRY THOROUGHLY BEFORE STORAGE
5. Carefully lift the Blending Jar straight up to
remove. The Ice Chute is spring-loaded and can be pushed up. If the Bending Jar is not easily removed, rock gently and lift. Do not twist.
6. Turn the Blending Jar upside down and unscrew the
Jar Base counter clockwise (to the left). Carefully remove the Blending Blade, and Blending Blade Sealing Ring.
WARNING: THE BLENDING BLADE IS SHARP. HANDLE WITH CARE.
Figr 6
7. To remove the Ice Melt Reservoir hold the unit still
and pull straight out on the handle.
The Ice Reservoir Lid, Ice Reservoir, Shaving Paddle,
8.
Ice Hopper, Shaving Blade Assembly Nut, Shaving Blade, Blending Jar Lid, Blending Jar, Blending Blade, Blending Blade Sealing Ring, Jar Base and Ice Melt Reservoir can be safely washed in the top rack of your dishwasher. Use only top rack. Failure to do so will result in damage.
Figr 7
Figr 4
ICE DEFLECTOR
Figr 5
Do not place the aluminum ice shaving paddle in the
dishwasher as discoloration will occur.
9. Use a damp cloth to clean the outside of the unit.
WARNING: UNPLUG UNIT BEFORE CLEANING. DO NOT USE SOLVENTS. NEVER IMMERSE THE UNIT IN WATER.
10. Clean the inside walls of the ice chute with a damp cloth
after every use.
Figr 6
Figr 7
-11-
Troubleshooting
If the Power Indicator Light does not light:
Check that the unit is plugged into a working power outlet. If liquid leaks from the base of the Blending Jar:
Remove it from the unit and check that the Blending Blade Sealing Ring is properly installed and that the Blending Jar Base is tightened.
If water leaks from the unit: Empty the Ice Melt Reservoir and make sure reservoir is in place.
If the Blending Jar overfl ows during the Shave ’n Blend™ cycle: Follow the drink recipes included in “making frozen drinks” section and make sure to not exceed the specifi ed total volume.
If the Blending Jar will not sit on the Blending Base: Remove it from the unit and check for ice on the Blending Base. WARNING: unplug the unit before removing ice from the Blending Base.
If the shaver does not shave suffi cient ice for the liquid in the Blending Jar: Check that the Number of Drinks Rotary Switch setting corresponds to the amount of liquid in the Blending Jar.
If the drink is too watery: Make sure to follow the recipe guide (pg.6) or manually shave more ice until the desired consistency is achieved.
Dos and Don’ts
DO NOT Place fi ngers into the Blending Jar or Ice Hopper. The blades in this
unit are sharp and could cause injury. DO NOT place Blending Jar onto Blending Base while motor is running. The
spinning Blending Base could damage the Blending Jar. DO NOT twist Blending Jar when removing. Simply lift and remove. Twisting
the Blending Jar could loosen the Blending Jar Base causing it to leak. DO NOT put hot liquid into the Blending Jar. Hot liquids could be ejected
during the blending process causing injury. DO NOT place ice, frozen foods or very cold liquids into a Blending Jar which
has come directly from a hot dishwasher. The sudden change in temperature could cause the Blending Jar to crack.
DO NOT place very hot liquids or foods into a Blending Jar that has come directly from the freezer. The sudden change in temperature could cause the Blending Jar to crack.
DO Follow the Cleaning and Maintenance instructions prior to your fi rst use. DO unplug the unit when not in use.
-12-
1 Year Limited Warranty
Sunbeam Products, Inc, d/b/a Jarden Consumer Solutions or if in Canada, Sunbeam Corporation (Canada) Limited d/b/a Jarden Consumer Solutions (collectively “Sunbeam”) warrants that for a period of one year from the date of purchase, this product will be free from defects in material and workmanship. Sunbeam, at its option, will repair or replace this product or any component of the product found to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component. If the product is no longer available, replacement may be made with a similar product of equal or greater value. This is your exclusive warranty.
This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the original sales receipt. Proof of purchase is required to obtain warranty performance. Sunbeam dealers, service centers, or retail stores selling Sunbeam products do not have the right to alter, modify or any way change the terms and conditions of this warranty.
This warranty does not cover normal wear of parts or damage resulting from any of the following: negligent use or misuse of the product, use on improper voltage or current, use contrary to the operating instructions, disassembly, repair or alteration by anyone other than Sunbeam or an authorized Sunbeam service center. Further, the warranty does not cover: Acts of God, such as fi re, fl ood, hurricanes and tornadoes.
What are the limits on Sunbeam’s Liability?
Sunbeam shall not be liable for any incidental or consequential damages caused by the breach of any express, implied or statutory warranty or condition.
Except to the extent prohibited by applicable law, any implied warranty or condition of merchantability or fi tness for a particular purpose is limited in duration to the duration of the above warranty.
Sunbeam disclaims all other warranties, conditions or representations, express, implied, statutory or otherwise.
Sunbeam shall not be liable for any damages of any kind resulting from the purchase, use or misuse of, or inability to use the product including incidental, special, consequential or similar damages or loss of profi ts, or for any breach of contract, fundamental or otherwise, or for any claim brought against purchaser by any other party.
Some provinces, states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to you.
This warranty gives you specifi c legal rights, and you may also have other rights that vary from province to province, state to state or jurisdiction to jurisdiction.
How to Obtain Warranty Service
If you have any question regarding this warranty or would like to obtain warranty service, please call 1- 877-689-2737 and a convenient service center address will be provided to you.
In the U.S.A., this warranty is offered by Sunbeam Products, Inc. located in Boca Raton, Florida 33431.
PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF THESE ADDRESSES OR TO THE PLACE OF PURCHASE.
-13-
Loading...
+ 33 hidden pages