Marantz VP-11S1, VP-11S1/N1M, VP-11S1/FW, VP-11S1/U1M, VP-11S1/U1B Service Manual

Page 1
Service
VP11S1 /F W/N1M/U1M
/U1B
Manual
P801 (Q522) AD9888 ADJUSTMENT METHODE
ADJUSTMENT PURPOSE:
This Adjustment may be needed when especially P701 or P801 are replaced. In addition, "Signal Generator" is required for this adjustment.
REASON :
"P701 and P801 are replaced in a pair" is written in the service manual. Because, the adjustment value of P801 (Q522 AD9888) is saved P701. If P701 and P801 are replaced separately, adjustment value will shift, the color of screen becomes purplish red in the whole, readjustment is necessary to make it right color.
DLP Projector
ADDENDUM INFORMATION
調整目的:
または
P701
尚、この調整には「信号発生器」が必要です。
理由:
P701とP801
その理由は、 ペア以外で 正しい色にする為に再調整が必要となります。
SECTION
1. AD9888 ADJUSTMENT METHODE / (JAPAN Ver)......................................................1 / (18)
2. HOW TO USE THE SIGNAL GENERATOR (SECORE VP403)...................................................15
Please use this service manual with referring to the user guide ( D.F.U. ) without fail.
PWB
を交換した場合、調整が必要となる場合があります。
P801
はサービスマニュアルでは、ペアでの交換となっています。
P801(Q522 ADA9888
を交換した場合は、調整値がずれ、スクリーンの色が全体的に初期値の赤紫となります。
)の調整値は
に保存されています。
P701
VP-11S1
VP-11S1
Part no. 90M19AV855020
MZ
Page 2
MARANTZ DESIGN AND SERVICE
Using superior design and selected high grade components, Only original
MARANTZ
parts can insure that your
MARANTZ
MARANTZ
product will continue to perform to the specifi cations for which
company has created the ultimate in stereo sound.
it is famous. Parts for your
MARANTZ
ORDERING PARTS :
equipment are generally available to our National Marantz Subsidiary or Agent.
Parts can be ordered either by mail or by Fax.. In both cases, the correct part number has to be specifi ed. The following information must be supplied to eliminate delays in processing your order :
1. Complete address
2. Complete part numbers and quantities required
3. Description of parts
4. Model number for which part is required
5. Way of shipment
6. Signature : any order form or Fax. must be signed, otherwise such part order will be considered as null and void.
USA
MARANTZ AMERICA, INC
1100 MAPLEWOOD DRIVE ITASCA, IL. 60143 USA PHONE : 630 - 741 - 0300 FAX : 630 - 741 - 0301
AUSTRALIA
QualiFi Pty Ltd,
24 LIONEL ROAD, MT. WAVERLEY VIC 3149 AUSTRALIA PHONE : +61 - (0)3 - 9543 - 1522 FAX : +61 - (0)3 - 9543 - 3677
EUROPE / TRADING
MARANTZ EUROPE B.V.
P. O. BOX 8744, BUILDING SILVERPOINT BEEMDSTRAAT 11, 5653 MA EINDHOVEN THE NETHERLANDS PHONE : +31 - 40 - 2507844 FAX : +31 - 40 - 2507860
THAILAND
MRZ STANDARD CO., LTD
746 - 754 MAHACHAI ROAD., WANGBURAPAPIROM, PHRANAKORN, BANGKOK, 10200 THAILAND PHONE : +66 - 2 - 222 9181 FAX : +66 - 2 - 224 6795
CANADA
MARANTZ CANADA INC.
5-505 APPLE CREEK BLVD. MARKHAM, ONTARIO L3R 5B1 CANADA PHONE : 905 - 415 - 9292 FAX : 905 - 475 - 4159
SINGAPORE
WO KEE HONG DISTRIBUTION PTE LTD
No.1 JALAN KILANG TIMOR #08-03 PACIFIC TECH CENTRE SINGAPORE 159303 PHONE : +65 6376 0338 FAX : +65 6376 0166
NEW ZEALAND
WILDASH AUDIO SYSTEMS NZ
14 MALVERN ROAD MT ALBERT AUCKLAND NEW ZEALAND PHONE : +64-9-8451958 FAX :+64-9-8463554
JAPAN
D&M Holdings Inc.
D&M BUILDING, 2-1 NISSHIN-CHO, KAWASAKI-KU, KAWASAKI-SHI, KANAGAWA, 210-8569 JAPAN
TAIWAN
PAI- YUING CO., LTD.
6 TH FL NO, 148 SUNG KIANG ROAD, TAIPEI, 10429, TAIWAN R.O.C. PHONE : +886 - 2 - 25221304 FAX : +886 - 2 - 25630415
MALAYSIA
WO KEE HONG ELECTRONICS SDN. BHD.
2ND FLOOR BANGUNAN INFINITE CENTRE LOT 1, JALAN 13/6, 46200 PETALING JAYA SELANGOR DARUL EHSAN, MALAYSIA PHONE : +60 - 3 - 7954 8088 FAX :+60-3-79547088
KOREA
MARANTZ KOREA CO., LTD.
ROOM 604, ELECTRO OFFICE, 16-58, HANGGANG-RO 3GA, YONGSAN-KU, SEOUL, 140-013, KOREA PHONE : +82 - 2 - 323 - 2155 FAX : +82 - 2 - 323 - 2154
CHINA
MARANTZ SHANGHAI TRADING LTD.
ROOM.506 SHANGHAI LIGHT INDUSTRY MANSION 1578 NANJING (WEST) ROAD SHANGHAI CHINA TEL : 021 - 6248 - 1064 FAX : 021 - 6248 - 3565
SHOCK, FIRE HAZARD SERVICE TEST :
CAUTION : After servicing this appliance and prior to returning to customer, measure the resistance between either primary AC
cord connector pins ( with unit NOT connected to AC mains and its Power switch ON ), and the face or Front Panel of product and controls and chassis bottom. Any resistance measurement less than 1 Megohms should cause unit to be repaired or corrected before AC power is applied, and verifi ed before it is return to the user/customer. Ref. UL Standard No. 60950.
In case of diffi culties, do not hesitate to contact the Technical
Department at above mentioned address.
060223MZ
Page 3
1

AD9888 Adjustment Methode

VP-11S1
Page 4

Necessaries

2
9 RGB signal generator
VGA/60Hz RGB signal generator in which the output of the following signal is possible 80% White / 100% Black (Setup = 0 IRE)
9 Component signal generator
480P/60Hz Component signal generator in which the output of the following signal is possible 100% Black (Setup = 0 IRE) / 100% saturation Yellow / 100% saturation Cyan 720P/60Hz Component signal generator in which the output of the following signal is possible 100% Black (Setup = 0 IRE) / 100% saturation Yellow / 100% saturation Cyan
The signal generator for adjustment recommends SENCORE VP403.
9 Windows PC built in RS-232C terminal (Windows 2000/ XP) 9 RS-232C cable (straight type : Female <-> Female) 9 Application software for AD adjustment : AtAdAdjEng.exe

Connnections

VP-11S1
VGA cable
RS-232C straight cable

Preparation for AD adjustment

The following folder is copied to a desktop.
Signal generator
Component cable Connect to COMP1
PC
AtAdAdjEnglish
Page 5

How to adjust

3
(1) Connect all cables to the projector base on "C
(2) Press the power button on the projector.
(3) Waits that the Lamp does light up.
(4) Double click the application file
the desktop.
"AtAdAdjEng.exe" of the folder AtAdAdjEnglish on
onnections".
Page 6
(5) Press E on the keyboard.
4
The following setup is a setup at the time of using SENCORE VP403.
Change the following value.
(6) Click the OK button.
700 Æ 560 650 Æ 640 650 Æ 630
Page 7
(7) Press space key on the keyboard.
5
Confirms that the following message.
Page 8
(8) Input 80% White RGB signal.
6
space key on the keyboard.
Press
Confirms that the following message.
Page 9
(9) Input 100%Black RGB signal.
7
space key on the keyboard.
Press
Confirms that the following message.
Page 10
(10) Input 100% saturation Yellow 480P/60Hz Component signal.
8
space key on the keyboard.
Press
Confirms that the following message.
Page 11
(11) Input 100% saturation Cyan 480P/60Hz Component signal.
9
space key on the keyboard.
Press
Confirms that the following message.
Page 12
(12) Input 100% Black 480P/60Hz Component signal.
10
space key on the keyboard.
Press
Confirms that the following message.
Page 13
(13) Input 100% saturation Yellow 720P/60Hz Component signal.
11
space key on the keyboard.
Press
Confirms that the following message.
Page 14
(14) Input 100% saturation Cyan 720P/60Hz Component signal.
12
space key on the keyboard.
Press
Confirms that the following message.
Page 15
(15) Input 100% Black 720P/60Hz Component signal.
13
space key on the keyboard.
Press
Confirms that the following message.
(16) Press Standby button
on the projector.
(17) Remove all connection cables.
Page 16

Trouble shooting against adjustment problem

14
Adjustment problem mode An adjustment process will stop into an adjustment process. Adjustment is not completed.

When the adjustment problem occurs into 480p-RGB adjustment process

Î Press ESC key on the key board. Adjustment process returns to an initial 480p-RGB
adjustment process. Again, please perform 480p-RGB adjustment process.

When the adjustment problem occurs into 480p-YUV adjustment process

Î Press ESC key on the key board. Adjustment process returns to an initial 480p-YUV
adjustment process. Again, please perform 480p-YUV adjustment process.

When the adjustment problem occurs into 720p-YUV adjustment process

Î Press ESC key on the key board. Adjustment process returns to an initial 720p-YUV
adjustment process. Again, please perform 720p-YUV adjustment process.
Page 17
15

HOW TO USE SENCORE VP403

Page 18

1. How to set up VGA/60Hz RGB 80% White

16
(1) Press ON/OFF button. (2) Press SIGNAL TYPE button. (3) Select VESA/Mac-RGB. (4) Press FORMAT button. (5) Select 640x480_60Hz. (6) Press PA TTERN button. (7) Select Raster 100 IRE (8) Select IRE adjust (9) Change Raster 80 IRE from 100 IRE by press by + - button.

2. How to set up VGA/60Hz RGB 100% Black

(10) Change Raster 0 IRE from 80 IRE by press by + - button.

3. How to set up 480p Yellow 100% YPbPr

(1) Press SIGNAL TYPE button. (2) Select HDTV/SDTV-YPbPr. (3) Press FORMAT button. (4) Select 480p59. (5) Press PA TTERN button. (6) Select Raster 80 IRE (7) Select IRE adjust (8) Change Raster 100 IRE from 80 IRE by press by + - button. (9) Press GATING button. (10) Select BLU -> OFF.

5. How to set up 480p Cyan 100% YPbPr

(11) Select BLU-> ON (12) Select RED -> OFF.

6. How to set up 480p Black 100% YPbPr

(13) Select RED -> ON. (14) Press PATTERN button. (15) Select IRE adjust (16) Change Raster 0 IRE from 100 IRE by press by + - button.
Page 19
17

7. How to set up 720p Yellow 100% YPbPr

(1) Press FORMAT button. (18) Select 720p59. (19) Press PATTERN button. (20) Select Raster 0 IRE (21) Select IRE adjust (22) Change Raster 100 IRE from 0 IRE by press by + - button. (23) Press GATING button. (24) Select BLU -> OFF.

8. How to set up 720p Cyan 100% YPbPr

(25) Select BLU -> ON (26) Select RED -> OFF.

9. How to set up 720p Black 100% YPbPr

(27) Select RED -> ON. (28) Press PATTERN button. (29) Select Raster 100 IRE (30) Change Raster 0 IRE from 100 IRE by press by + - button.
Page 20
18

AD9888 調整手順

VP-11S1
Page 21
適用
19
本調整手順は、VP-11S1 に実装される AD コンバータ(アナログデバイセズ製 AD9888)の調整に適 用されます。

準備する物

9 RGB 信号発生器
VGA/60Hz RGB 信号 80% White / 100% Black (Setup = 0 IRE) が出力可能なテスト信号発生器
9 コンポーネント信号発生器
480P/60Hz コンポーネント信号
《100% White / 100% Black (Setup = 0 IRE) / 100%飽和 Yellow / 100% 飽和シアン》 が出力可能なテスト信号発生器
720P/60Hz コンポーネント信号 100% White / 100% Black (Setup = 0 IRE / 100%飽和 Yellow / 100% 飽和シアン》
(本文章で使用するテスト信号発生器は、上記 2 項の条件を 1台で満足するテスト信号発生器とします。)
信号発生器は SENCORE VP403 を推奨します。
9 RS-232C 端子が実装された Windows PC 9 RS-232C ストレートケーブル(メス - メス) 9 調整用アプリケーション AtAdAdj_1_08
接続
VGA ケーブル
VP-11S1
テスト信号発生器
コンポーネントケーブル
COMP1 入力に接続
RS-232C ストレートケーブ
PC
Page 22
20
準備
1. 使用する PC に調整用アプリケーション AtAdAdj_1_08 をインストールします。
2. 調整用アプリケーション AtAdAdj_1_08 を立ち上げます。
3. 上下キーで、項目ポート番号かデータ取得回数を決定します。
4. 左右キーで、使用する COM ポートの番号とデータ取得回数(推奨 3)を決定します。
この値はこのままの値を使用して下さい。
Page 23
5. AtAdAdj を立ち上げ、キ-ボ-ドで E を押して下さい。
21
下記のメニュ-が現れます。 赤丸の部分 3 ケ所が 560 であることを確認して下さい。
700 の場合は 560 にキ-入力で変更して下さい。 設定 700 は白 100%入力の設定です。 設定 560 は白 80%入力の設定です。
信号発生器 SENCORE VP403 を使用時にはさらに 480p-YUV Y 650 から 640
720p-YUV Y 650 から 630 に変更して下さい。
700 Æ 560
650 Æ 640 650 Æ 630
6. 調整用アプリケーション AtAdAdj_1_08 を終了します。
セットのBuildBuild-00XX以降であることを確認して下さい。
7.
Page 24

調整手順

22
1. PC とテスト信号発生器の電源を立ち上げます。
2. 接続図に沿ってプロジェクターと PC とテスト信号発生器を接続します。
3. プロジェクターの電源を立ち上げます。
4. 調整用アプリケーション AtAdAdj_1_08 を立ち上げます。
5. PC SPACE キーを押し、調整を開始する (RGB 入力は自動的に切り替わります)
Page 25
6. RGB に 480P 白を入力し、PC の SPACE キーを押します。
23
Page 26
7. 下記のメッセ-ジを確認後、RGB 480P 黒を入力し、PC SPACE キーを押します。
24
Page 27
8. 下記のメッセ-ジを確認して下さい。
25
480p-RGB 調整完了後、自動で 480p-YUV 調整に移行します。
セット本体の入力は自動で COMP1 に切り替わります。
COMP1 480P 黄色を入力し、PC SPACE キーを押します。
Page 28
9. 下記のメッセ-ジを確認後、COMP1 480P シアンを入力し、PC SPACE キーを押し
26
ます。
Page 29
10. 下記のメッセ-ジを確認後、COMP1 480P 黒を入力し、PC SPACE キーを押し
27
ます。
Page 30
11. 下記のメッセ-ジを確認して下さい。
28
480p-YUV 調整完了後、自動で 720p-YUV 調整に移行します。
COMP1 720P 黄色を入力し、PC SPACE キーを押します。
Page 31
12. 下記のメッセ-ジを確認後、COMP1 720P シアンを入力し、PC SPACE キーを押し
29
ます。
Page 32
13. 下記のメッセ-ジを確認後、COMP1 720P 黒を入力し、PC SPACE キーを押し
30
ます。
Page 33
14. 下記のメッセ-ジを確認で調整完了です。 本機をスタンバイにして下さい。
31
15. AC コ-ドを含むすべてのコ-ドを外して下さい。
Page 34
<調整過程で調整の不具合が発生した場合>
32
調整不具合モ-ド調整中止まる。調整が終了しない。

480p-RGB調整過程で調整不良が発生した場合

Î ESC キ-を押して下さい。480p-RGB 調整の初期に戻ります。
480p-RGB 調整を再試行して下さい。

480p-YUV調整過程で調整不良が発生した場合

Î ESC キ-を押して下さい。480p-YUV 調整の初期に戻ります。
480p-YUV 調整を再試行して下さい。

720-YUV調整過程で調整不良が発生した場合

Î ESC キ-を押して下さい。720p-YUV 調整の初期に戻ります。
720p-YUV 調整を再試行して下さい。
Loading...