Marantz CD5000 User Manual

Download

Model CD5000 User Guide

CD PLAYER

CAUTION

WARNING

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

ATTENTION:

POUR EVITER LES CHOCS ELECTRIQUES, INTRODUIRE LA LAME LA PLUS LARGE DE LA FICHE DANS LA

BORNE CORRESPONDANTE DE LA PRISE ET POUSSER JUSQU’AU FOND.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

LASER SAFETY

This unit employs a laser, Only a qualified service person should remove the cover or attempt to service this device, due to possible eye injury.

CAUTION

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURE OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

English ....................................................4

Français.................................................14

EnglishFrançais

NOTE

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference

by one or more of the following measures:

– Reorient or relocate the receiving antenna. – Increase the separation between the

equipment and receiver.

– Connect the equipment into an outlet on a

circuit different from that to which the receiver is connected.

– Consult the dealer or an experienced

radio/TV technician for help.

NOTE

Changes or modifications may cause this unit to fail to comply with Part 15 of the FCC Rules and may void the user’s authority to operate the equipment.

This Class B digital apparatus meets all requirements of the Canadian InterferenceCausing Equipment Regulations.

Cet appareil numérique de la Classe B respecte toutes les exigences du Règlement sur le matérier brouilleur du Canada.

CLASS 1 LASER PRODUCT

LUOKAN 1 LASERLAITE

KLASS 1 LASERAPPARAT

English

This product was designed and manufactured to meet strict quality and safety standards. There are, however, some installation and operation precautions which you should be particularly aware of.

1. Read Instructions - All the safety and operating instructions should be

read before the appliance is operated.

2. Retain Instructions - The safety and operating instructions should be

retained for future reference.

3. Heed Warnings - All warnings on the appliance and in the operating

instructions should be adhered to.

4. Follow Instructions - All operating and use instructions should be

followed.

5. Water and Moisture - The appliance should not be used near water -

for example, near a bathtub, washbowl, kitchen sink, laundry tub or swimming pool, or in a wet basement.

6. Carts and Stands - The appliance should be used only with a cart or

stand that is recommended by the manufacturer.

6A. An appliance and cart combination should be moved with

care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.

7. Wall or Ceiling Mounting - The appliance should be mounted to a

wall or ceiling only as recommended by the manufacturer.

8. Ventilation - The appliance should be situated so that its location or

position does not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or, placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.

9. Heat - The appliance should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including amplifiers) that produce heat.

10. Power Sources - The appliance should be connected to a power

supply only of the type described in the operating instructions or as marked on the appliance.

11. Grounding or Polarization - Precautions should be taken so that the

grounding or polarization means of an appliance is not defeated.

Caution:To prevent electric

shock, match the wide blade of this plug to the wide slot and fully insert. Do not use this (polarized) plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure.

12. Power Cord Protection - Power supply cords should be routed so that

they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance.

13. Cleaning - The appliance should be cleaned only as recommended by

the manufacturer.

14. Power Lines - An outdoor antenna should be located away from power

lines.

15. Outdoor Antenna Grounding - If an outside antenna is connected to

the receiver, be sure the antenna system is grounded so as to provide some protection against voltage surges and built up static charges. Section 810 of the National Electrical Code, ANSI/NFPA No. 70-1984, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding connectors, location of antennadischarge unit, connection to grounding electrodes, and requirements for the grounding electrode. See figure below.

16. Non-use Periods - The power cord of the appliance should be

unplugged from the outlet when left unused for a long period of time.

17. Object and Liquid Entry - Care should be taken so that objects do not

fall and liquids are not spilled into the enclosure through openings.

18. Damage Requiring Service - The appliance should be serviced by

qualified service personnel when:

A. The power supply cord or the plug has been damaged; or B. Objects have fallen, or liquid has spilled into the appliance; or C. The appliance has been exposed to rain; or D. The appliance does not appear to operate normally or exhibits a

marked change in performance; or

E. The appliance has been dropped, or the enclosure damaged.

19. Servicing - The user should not attempt to service the appliance

beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel.

SAFETY INSTRUCTIONS – Read before operating equipment

Note to the Cable TV system installer

This reminder is provided to call the Cable TV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

Polarized Plug

Example of Antenna Grounding as per NEC - National Electrical Code

Ground Clamp

Antenna Lead-in Wire

Antenna Discharge Unit (NEC Section 810-20)

Grounding Conductors (NEC Section 810-21) Ground Clamps

Electric Service Equipment

Power Service Grounding Electrode System (NEC Art. 250, Part H)

GENERAL INFORMATION

Clean the CD player with a soft, slightly dampened lint-free cloth. Do not use any cleaning agents as they may have a corrosive effect.

Do not expose the CD player, batteries or CDs to humidity, rain, sand or excessive heat (caused by heating equipment or direct sunlight).

This CD player can play all kinds of Audio Discs such as CD-Recordables, CD-Rewriteables and CD-Text CDs. Do not try to play a CD-ROM, CD-I, CDV or computer CD.

If the CD player cannot read CDs correctly use a commonly available cleaning CD to clean the lens before taking the CD player to repair. Other cleaning methods may destroy the lens. Always keep the tray closed to avoid dust on the lens.

The lens may cloud over when the CD player is suddenly moved from cold to warm surroundings. Playing a CD is not possible then. Leave the CD player in a warm environment until the moisture evaporates.

To clean a CD, wipe it in a straight line from the center toward the edge using a soft, lint-free cloth. A cleaning agent may damage the disc! Never write on a CD or attach a sticker to it.

Subject to modification without notice.

Standby power consumption .............................................< 5W

Frequency range ....................................................20–20,000Hz

Amplitude linearity ..................................< 0.5dB (1kHz, -90dB)

Dynamic range.........................................................98dB (1kHz)

Signal-to-noise ratio.........................108dB (1kHz, A-weighted)

Channel separation..................................................98dB (1kHz)

Total harmonic distortion.........................0.004%, -88dB (1kHz)

Audio output ...............................................2V RMS ±3dB, 1kΩ

Digital coaxial output.....................................75Ω acc. IEC 958

Digital optical output .....................................................-19dBm

Impedance headphones.......30–600Ω (5V e. m. f. from 120Ω)

Dimensions..................................................435 × 86 × 265mm

Weight................................................................................2.9kg

Technical data

Maintenance

English

Table of contents

GENERAL INFORMATION

Maintenance................................................................5

Technical data ..............................................................5

CONTROLS AND CONNECTIONS

Controls on the front....................................................6

Connections at the back ..............................................6

INSTALLATION AND REMOTE CONTROL

Accessoires..................................................................7

Connections

Usual connection, LINE OUT ....................................7

Digital connection, DIGITAL OUT.............................7

Mains ...........................................................................7

Remote control.............................................................7

Batteries...................................................................7

PLAYBACK

CD Text .........................................................................8

Discs for playback........................................................8

Playing a CD.................................................................8

ADDITIONAL FUNCTIONS

Selecting a track and searching

Selecting a track during CD play .............................9

Selecting a track when CD play is stopped.............9

Searching for a passage during CD play .................9

Random order playing (SHUFFLE) ................................9

Repeating a CD, a track or a program.........................9

Repeating a part of the CD..........................................9

Programming track numbers......................................10

Clearing the program .................................................10

Loudest passage searching .......................................10

Time display...............................................................10

Fading out and in .......................................................11

Volume adjustment....................................................11

Locking the volume ....................................................11

Headphone listening..................................................11

Scanning the CD ........................................................11

Recording setup .........................................................12

Environmental information.........................................12

TROUBLESHOOTING

Warning......................................................................13

Troubleshooting..........................................................13

CONTROLS AND CONNECTIONS

Controls on the front

1 POWER ON / STANDBY...switches the CD player on and

to standby

2 OPEN·CLOSE......................opens and closes the CD tray

3 Sensor for the infrared remote control 4 Display

5 TIME....................................switches through the different

time information

6 SCROLL...............................scrolls CD-Text information

7 CD TEXT..............................switches through the different

CD-Text information

8 HIGHLIGHT.........................plays the beginning of each

track or – if a CD-Text disc contains highlights – the highlights of a CD

9 SHUFFLE.............................plays a CD or a program in

random order

0 FADE....................................fades CD play out and in

! PREV. ∞ .............................selects the beginning of the

current or a previous track, and searches backward

@ PLAY 2 ................................starts CD play

# PAUSE ;..............................interrupts CD play

$ STOP 9 ...............................stops CD play and clears a

program

% NEXT § ..............................selects the beginning of a

subsequent track, and searches forward

^ VOLUME .............................decreases or increases the

volume level of the headphones

& PHONES..............................6.3mm headphone socket

* PEAK ...................................searches the loudest passage

of a CD

( EDIT.....................................changes the settings for

recording on tape or CD-Recordable

) PROGRAM..........................programs track numbers

English

Connections at the back ¡ COAXIAL / OPTICAL

DIGITAL OUT......................to connect the digital input of

a digital audio device

™ LINE OUT L R .....................to connect the audio input of

an amplifier

£ MAINS LEAD .....................After all other connections

have been made, connect this mains lead to the wall socket.

CD PLAYER CD5000

POWER ON/STANDBY

CD REWRITABLE PLAYBACK

OPEN/CLOSE

STOPPLAY

LEVEL

789 0 !@ # %

TIME

HIGHLIGHT SHUFFLE FADE

PEAKEDITPROG

PREV PAUSE NEXT

PHONES

*()

CD TEXT

SCROLL

INSTALLATION AND REMOTE CONTROL

This CD player is supplied including: – a remote control – 2 batteries for the remote control – a connection cable – this instruction booklet

Usual connection, LINE OUT 1 Insert the red plug of the supplied connection cable into R

and the other plug into L.

2 Insert the other side of the cable into the corresponding

sockets of the CD or AUX input of your amplifier.

Important!

You may also use the TUNER or TAPE, but never the PHONO input of your amplifier!

Digital connection, DIGITAL OUT Never connect this socket to a non-digital input – such as

AUX, CD, PHONO, TAPE – of an amplifier. This output supplies a digital signal and can therefore only be connected to a digital input.

1 Insert an optional coaxial cable into DIGITAL OUT.

2 Insert the other side of the cable into the digital input of

your digital device (e. g. CD Recorder).

The type plate is located on the bottom of the CD player.

1 Check whether the mains voltage as shown on the type

plate corresponds to your local mains voltage. If it does not, consult your dealer or service organisation.

2 Connect the mains cable to the wall socket. This switches

on the mains supply.

Note: To disconnect the CD player from the mains completely,

remove the mains plug from the wall socket.

Batteries

• Open the battery compartment of the remote control and

insert 2 alkaline batteries, type AAA (R03, UM-4).

Remove batteries if they are flat or the remote control is not going to be used for a long time.

Batteries contain chemical substances, so they should be disposed of properly.

TIME......................switches through the different time

informations

............................switches the CD player to standby

PROG.....................programs track numbers

FADE......................fades CD play out and in

SHUFFLE...............plays a CD or a program in random order

DIGITS 0–9 ...........selects a track by number

HIGHLIGHT...........plays the beginning of each track or – if a

CD-Text disc contains highlights – the highlights of a CD

REPEAT.................repeats a track, a program or the entire

VOLUME –............decreases the volume level

VOLUME +............increases the volume level

PLAY 2..................starts CD play

PREV. ∞ ...............selects the beginning of the current or a

previous track

NEXT § ................selects the beginning of a subsequent

track

STOP 9 .................stops CD play and clears a program

5 ...........................searches backward

PAUSE ;................interrupts CD play

6 ...........................searches forward

CD TEXT................switches through the different CD-Text

information

SCROLL.................scrolls CD-Text information

REPEAT A/B.........repeats a selected part of the CD

Remote control

Mains

Connections

Accessories

English

T IM

P R

O G

R AM

D ER

U F

–

VOLUM

STO

CD TEXT

NEX

USE

SCRO

PEAT A

FLE

REPEAT

PLAYBACK

This CD player can show information which is stored on CDText discs. It will only reproduce the text which is recorded on the disc.

1 When inserting a disc with CD-Text the display shows

CD TEXT and performing artist or group. In case there are

various artists the album title is shown.

2 Press CD TEXT before playing a CD to switch between

album title and performing artist(s) if available.

3 Press CD TEXT during CD play to switch between album

title, performing artist(s) and track title if available.

4 At the beginning of a new track the track title is scrolled

once. Then the first 12 digits of the track title are displayed.

5 CD-Text information is scrolled every 30 seconds. Press

SCROLL to scroll the text through the display any time.

This system can play all audio CD, finalized audio CDRecordable and finalized audio CD-Rewritable format discs.

1 Use POWER ON / STANDBY to switch on the CD player.

2 Press OPEN·CLOSE to open the CD tray.

y OPEN appears on the display.

3 Insert an audio CD (printed side up) and press OPEN·CLOSE

to close the CD compartment.

y READING appears on the display. Then the number

of tracks and the playing time is shown. If the disc contains CD-Text the display shows CD TEXT and CD-Text information (see “CD-Text”).

4 Press PLAY 2 to start CD play.

y The display shows , TRACK, TIME, and the number and

time of the actual track. If the disc contains CD-Text the display shows CD-Text information.

• You can interrupt CD play by pressing PAUSE ;.

y The display shows and the track number and time

where playback was stopped.

• Continue CD play by pressing PAUSE ; again.

5 Press STOP 9 to stop CD play.

Note: Playback will also stop if the end of the CD is reached.

Playing a CD

Discs for playback

CD-Text

English

POWER ON/STANDBY

CD PLAYER CD5000

CD REWRITABLE PLAYBACK

OPEN/CLOSE

CD TEXT

SCROLL

TIME

HIGHLIGHT SHUFFLE FADE

STOPPLAY

PEAKEDITPROG

PREV PAUSE NEXT

PHONES

LEVEL

ADDITIONAL FUNCTIONS

Selecting a track during CD play

• Briefly press PREV. ∞ or NEXT § once or several times to skip to the beginning of the current, previous or subsequent track(s).

• Use the digits 0–9 on the remote control to key in the number of a track.

y CD play continues with the selected track.

Selecting a track when CD play is stopped 1 Briefly press PREV. ∞ or NEXT § once or several times.

• Use the digits 0–9 on the remote control to key in the number of a track.

2 Press PLAY 2 to start CD play.

y Playback starts with the selected track.

Searching for a passage during CD play 1 Hold down PREV. ∞ or NEXT § to find a particular

passage in a backward or forward direction.

y CD play continues at a low volume.

2 Release the button when you have reached the desired

passage.

Note: In the shuffle and repeat mode and when playing a

program, searching is only possible within the particular track.

1 Press SHUFFLE before or during CD play to start shuffle

play.

y SHUFFLE is shown in the display. All the tracks of the CD

(or program if available) will now be played in random order.

2 Press SHUFFLE again to return to normal CD play.

1 Press repeatedly REPEAT on the remote control during CD

play.

y The display shows the different repeating modes.

REPEAT 1: the current track is played repeatedly. REPEAT: the entire CD or program (if available) is played

repeatedly.

2 Press REPEAT until the display indication disappears to

return to normal CD play.

Note: It is possible to activate the different playing modes at

the same time, e. g. you can repeatedly play the entire CD or program in random order (PROGRAM REPEAT SHUFFLE).

1 Press PLAY 2 to start CD play.

2 Press REPEAT A/B on the remote control to mark the

beginning of the passage to be repeated.

y REPEAT is shown and A- is flashing in the display.

3 Press REPEAT A/B on the remote control to mark the end of

the passage to be repeated.

y REPEAT A-B is shown in the display. The part of the CD

between the marked points is played repeatedly.

4 Press PLAY 2 to return to normal CD play.

Repeating a part of the CD

Repeating the CD, a track or a program

Random order playing (SHUFFLE)

Selecting a track and searching

English

T SHUFFLE FADE

PEAKEDIT

PREV PAUSE NEXT

PHONES

LEVEL

ADDITIONAL FUNCTIONS

You can select a number of tracks and store these in the memory in the desired sequence. You can store any track more than once. At most, 30 tracks can be stored in the memory.

1 Press PROG to start programming.

y PROGRAM flashes.

Note: If you press PROG while playing a CD, the actual track

will be added to the program.

2 Press PREV. ∞ or NEXT § to select the desired track. or

• Key in the number of a track with the digits 0–9 on the remote control.

3 Press PROG to store the track number.

y TRACK, TOTAL TIME, and the number of the programmed

track is displayed. The number of programmed tracks is increased and the time of the track is added to the total time of the program.

4 Repeat steps 2 and 3 for all tracks to be programmed.

5 Press STOP 9 to end programming.

y PROGRAM lights permamently.

• It is possible to review the program using the PREV. ∞ or NEXT §. You can add more tracks by pressing PROGRAM like you have done before.

6 Press PLAY 2 to start program play.

Note: If you try to store more than 30 tracks

PROGRAM FULL scrolls through the display.

1 If necessary press STOP 9 to stop program playing.

2 Press STOP 9 to clear the program.

y PROGRAM CLEARED scrolls through the display,

PROGRAM disappears and your program is cleared.

Note: The program will also be cleared if you open the tray.

You can search for the loudest passage of a CD or program. This will help you in adjusting your recording device if required.

1 If necessary press STOP 9 to stop CD play.

2 Press PEAK to start searching.

y PEAK starts flashing. Searching may need a few

minutes. Then 4 seconds of the loudest passage are played repeatedly.

• You can interrupt peak play by pressing PAUSE ;. Continue peak play by pressing PAUSE ; again.

3 Press STOP 9 to stop playing. or

• Press PLAY 2 to start CD play.

You can display time information which is stored on the CD.

While playing a CD or a program the number and elapsed time of the actual track, and

TIME are displayed. If the disc

contains CD-Text the display shows CD-Text information (see “CD-Text”).

• Press TIME several times to display:

y If the disc contains CD-Text, the number and elapsed

time of the actual track, and TIME are displayed first.

y The number and remaining time of the actual track, and

REM TIME.

y The number of the actual track, the total elapsed time

of the CD, and TOTAL TIME.

y The number of the actual track, the total remaining time

of the CD, and TOTAL REM TIME.

Note: If you press TIME when the CD is not playing you may

only display the total time of the CD.

Time display

Loudest passage searching

Clearing the program

Programming track numbers

English

CD TEXT

SCROLL

TIME

HIGHLIGHT SHUFFLE FADE

PEAKEDITPROG

ADDITIONAL FUNCTIONS

You can fade out and in CD play, e. g. to stop and start a recording softly.

1 Press FADE during CD play to fade out.

y The display shows in steps. The volume is lowered

continuously until CD play is paused.

2 Press FADE again to fade in.

y The display shows in steps. CD play starts and the

volume is raised continuously to its previous level.

Note: You may use FADE anytime when CD play is paused to

fade in.

The volume of the CD player can be adjusted. This affects the DIGITAL OUT output as well.

• Press VOLUME – or VOLUME + on the remote control.

y The volume of the CD player is lowered or raised. The

display shows the actual value between VOLUME MIN and VOLUME MAX.

Important!

VOLUME –/+ is altering the signal of the output. Before recording set the volume to VOLUME MAX and do not change during recording.

It is possible to lock the output volume to its maximum. This affects the DIGITAL OUT output as well. Locking the volume can be usefull when recording from the CD-player.

• Keep EDIT pressed for more than 2 seconds.

If the voulme was unlocked:

y The display shows VOLUME FIXED and the

volume is locked.

If the voulme was locked:

y The display shows VOLUME MAX and the volume is

unlocked.

Note: If you press VOLUME –/+ and the volume is locked the

display shows VOLUME FIXED.

1 Connect your headphones to the 6.3mm PHONES socket.

2 Use LEVEL to adjust the volume of the headphones.

Note: The maximum volume on the headphones is set through

VOLUME –/+ on the remote control.

Important!

The volume of the headphones is in line with the volume of the output. Therefore do not use VOLUME –/+ during recording.

It is possible to listen to the beginning of each track of a CD or program. You can choose whether to play 10, 20 or 30 seconds of each track. If a disc contains CD-Text highlights this part of the tracks is scanned and HIGHLIGHT is displayed.

1 Press HIGHLIGHT repeatedly to switch through the different

scan modes.

y SCAN 10, SCAN 20, SCAN 30, SCAN

OFF… (SCAN OFF aborts the scan function).

2 As soon as the desired scan mode is displayed do not press

the button again.

y After 1 second scanning starts. The number and

remaining time of the actual track, and REM TIME are displayed.

• You can interrupt scan by pressing PAUSE ;. Continue scan by pressing PAUSE ; again.

3 Press STOP 9 to stop scanning. or

• Press PLAY 2 to start CD play with the actual track.

Note: If you press HIGHLIGHT while SHUFFLE is active,

shuffle will be stopped before scanning.

Scanning the CD

Headphone listening

Locking the volume

Volume adjustment

Fading out and in

English

HIGHLIGHT SHUFFLE FADE

PEAKEDITPROG

PREV PAUSE NEXT

PHONES

STOPPLAY

LEVEL

ADDITIONAL FUNCTIONS

It is possible to set up the CD player in a way that it will calculate which tracks will fit on your recording media. It is only possible to use the edit function if a disc has not more than 29 tracks.

If you use NORMAL the recording stops after the last track that fits on one side of your recording media. Notice that CDRecordables are single-sided only! If you use OPTIMAL some tracks will be skipped to minimise the unused space on your recording media. The sequence of the tracks stays as the original.

1 Insert a CD and, if desired, program track numbers.

2 Press EDIT to start the setup.

y The display shows NORMAL.

3 Press PREV. ∞ or NEXT § to switch through the different

scan modes.

y NORMAL, OPTIMAL, STOP… (STOP aborts the

edit function).

4 As soon as the desired edit mode is displayed press EDIT.

y The display shows C 90.

5 Press PREV. ∞ or NEXT § to switch through the different

recording times and media.

y C 100, C 120, CDR 21, CDR 60,

CDR 74, C30, C 45, C 60, C 90…

Note: C is for cassette, CDR is for CD-Recordable and

CD-Rewriteable and therefore for single-sided recording only.

6 As soon as the desired recording time and media is

displayed press EDIT.

y A, the number of tracks and the playing time are

displayed.

7 Start your recording and press PLAY 2 to start CD play.

y If cassette (C) was selected the CD player pauses after

playing the calculated tracks for side A. If CDRecordable (CDR) was selected the CD player stops.

8 If required switch tape sides.

9 Press PLAY 2 to start CD play again.

y B, the number of tracks and the playing time are

displayed. The remaining tracks for side B are played.

Note: It is possible to switch between A and B by using

PREV. ∞ or NEXT § .

Recording setup

English

Environmental information

All redundant packing material has been omitted. We have done our utmost to make the packaging easily separable into three mono materials: cardboard (box), polystyrene foam (buffer) and polyethylene (bags, protective foam sheet).

Your set consists of materials which can be recycled if disassembled by a specialized company. Please observe the local regulations regarding the disposal of packing materials, exhausted batteries and old equipment.

HIGHLIGHT SHUFFLE FADE

PEAKEDITPROG

PREV PAUSE NEXT

PHONES

STOPPLAY

LEVEL

TROUBLESHOOTING

English

WARNING

Under no circumstances should you try to repair the CD player yourself as this will invalidate the guarantee.

If a fault occurs, first check the points listed below before taking the set for repair.

If you are unable to solve a problem by following this checklist, consult your dealer or service center.

Problem Possible cause Solution

No power Mains cable is not securely connected. Connect mains cable properly. No or bad sound Volume is too low. Adjust volume.

Interference caused by electric equipment Keep the CD player away from electrical like TVs, computers, engines, etc. equipment.

Loose or wrong connections. Connect the CD player correctly.

No or bad headphone Volume is too low. Adjust VOLUME –/+.

Headphone plug is dirty. Clean headphone plug.

No or low quality Volume is too low. Adjust VOLUME –/+. recording

Loose or wrong connections. Connect the CD player correctly.

No reaction to Electrostatic discharge. Disconnect the CD player from mains, operation of any keys reconnect after a few seconds.

INSERT DISC

No CD is inserted. Insert a CD.

is displayed

The CD is badly scratched or dirty. Replace or clean the CD. The CD is inserted upside down. Insert CD with label upwards.

DISC NOT

The CD-RW (or CD-R) is not properly recorded Read the instruction booklet of your

FINALIZED

for the use on a standard CD player. CD-Rewriteable (or CD-Recordable) recorder

is displayed on how to finalize a recording.

The CD is badly scratched or dirty. Replace or clean the CD.

WRONG TRACK

Chosen track number is higher than the Key in a track number within the range of the

is displayed highest track number on the CD. track numbers on the CD.

0 0:00

is displayed First track of the CD is longer than the first Choose a recording media with a recording time

side of the chosen recording media. longer than the first track of the CD.

VOLUME FIXED

is Volume is locked. Press EDIT for more than 2 seconds to

displayed unlock the volume. Some CD-Text track Too much information on the CD-Text disc. Use a CD-Text disc with less information.

information is not displayed

CD skips tracks SHUFFLE or PROGRAM is active. Switch off SHUFFLE or PROGRAM play.

The CD is badly scratched or dirty. Replace or clean the CD. Laser lens is dirty. Clean with a commonly available cleaning CD. The laser lens is steamed up. Wait until the lens has cleared.

Remote control does Batteries are inserted incorrectly. Insert batteries correctly. not function properly

Batteries are flat. Insert fresh batteries. Distance to the CD player is too large. Reduce distance.

Marantz America, Inc.

440 Medinah Road Roselle, IL 60172-2330

Phone : (708) 307-3100 Fax : (708) 307-2687

is a registered trademark.

3139 116 19111 Printed In Singapore SL-9909/U1B-02

Marantz CD5000 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual