Makita M4501K operation manual

	EN	Recipro Saw	INSTRUCTION MANUAL	4
		Scie Recipro	MANUEL D’INSTRUCTIONS	8
	FR
		Reciprosäge	BETRIEBSANLEITUNG	12
	DE
		Seghetto diritto	ISTRUZIONI PER L’USO	16
	IT
		Reciprozaag	GEBRUIKSAANWIJZING	20
	NL
		Sierra Recíproca	MANUAL DE	24
	ES
			INSTRUCCIONES
		Serra Sabre	MANUAL DE INSTRUÇÕES	28
	PT
		Bajonetsav	BRUGSANVISNING	32
	DA
		Σπαθοσέγα	ΕΓΧΕΙΡΙΔΙΟ ΟΔΗΓΙΩΝ	36
	EL
		Kılıç Testere	KULLANMA KILAVUZU	40
	TR

M4500

M4501

1

2

Fig.1

2

	A
1
Fig.2
1
B
Fig.3	2
1	2
	3
	4
Fig.4
	2

1	2	3
		4
Fig.5		5
		1

2	3
Fig.6
	2
1
Fig.7
	1

2

Fig.8

1

2

Fig.9

Fig.10

1

Fig.11

1

Fig.12

3

ENGLISH (Original instructions)

SPECIFICATIONS

Model:		M4500		M4501
Length of stroke			28 mm
Strokes per minute			0 - 2,800 min-1
Max. cutting	Pipe		ø130 mm
capacities	Wood		255 mm
(with 150 mm
blade)
Overall length			457 mm
Net weight		3.1 kg		3.2 kg

•Due to our continuing program of research and development, the specifications herein are subject to change without notice.

•Specifications may differ from country to country.

•Weight according to EPTA-Procedure 01/2003

Intended use

The tool is intended for sawing wood, plastic, metal and building materials with a strong impact. It is suitable for straight and curved cutting.

Power supply

The tool should be connected only to a power supply of the same voltage as indicated on the nameplate, and can only be operated on single-phase AC supply. They are double-insulated and can, therefore, also be used from sockets without earth wire.

Noise

The typical A-weighted noise level determined according to EN60745:

Model M4500

Sound pressure level (LpA) : 88 dB(A) Sound power level (LWA) : 99 dB (A)

Uncertainty (K) : 3 dB(A)

Model M4501

Sound pressure level (LpA) : 87 dB(A) Sound power level (LWA) : 98 dB (A)

Uncertainty (K) : 3 dB(A)

WARNING: Wear ear protection.

Vibration

The vibration total value (tri-axial vector sum) determined according to EN60745:

Model M4500

Work mode: cutting boards

Vibration emission (ah,B) : 19.5 m/s2

Uncertainty (K) : 1.5 m/s2

Work mode: cutting wooden beams

Vibration emission (ah,WB) 22.0 m/s2

Uncertainty (K) : 2.0 m/s2

Model M4501

Work mode: cutting boards

Vibration emission (ah,B) : 19.5 m/s2

Uncertainty (K) : 1.5 m/s2

Work mode: cutting wooden beams

Vibration emission (ah,WB) 22.0 m/s2

Uncertainty (K) : 2.0 m/s2

NOTE: The declared vibration emission value has been measured in accordance with the standard test method and may be used for comparing one tool with another.

NOTE: The declared vibration emission value may also be used in a preliminary assessment of exposure.

WARNING: The vibration emission during actual use of the power tool can differ from the declared emission value depending on the ways in which the tool is used.

WARNING: Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).

EC Declaration of Conformity

For European countries only

Makita declares that the following Machine(s): Designation of Machine: Recipro Saw

Model No./ Type: M4500, M4501

Conforms to the following European Directives: 2006/42/EC

They are manufactured in accordance with the following standard or standardized documents: EN60745

The technical file in accordance with 2006/42/EC is available from:

Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium 24.8.2015

Yasushi Fukaya

Director

Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

4 ENGLISH

General power tool safety warnings

WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated

(cordless) power tool.

Recipro saw safety warnings

1.Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and could give the operator an electric shock.

2.Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control.

3.Always use safety glasses or goggles. Ordinary eye or sun glasses are NOT safety glasses.

4.Avoid cutting nails. Inspect workpiece for any nails and remove them before operation.

5.Do not cut oversize workpiece.

6.Check for the proper clearance beyond the workpiece before cutting so that the blade will not strike the floor, workbench, etc.

7.Hold the tool firmly.

8.Make sure the blade is not contacting the workpiece before the switch is turned on.

9.Keep hands away from moving parts.

10.Do not leave the tool running. Operate the tool only when hand-held.

11.Always switch off and wait for the blade to come to a complete stop before removing the blade from the workpiece.

12.Do not touch the blade or the workpiece immediately after operation; they may be extremely hot and could burn your skin.

13.Do not operate the tool at no-load unnecessarily.

14.Always use the correct dust mask/respirator for the material and application you are working with.

15.Some material contains chemicals which may be toxic. Take caution to prevent dust inhalation and skin contact. Follow material supplier safety data.

SAVE THESE INSTRUCTIONS.

WARNING: DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.

FUNCTIONAL

DESCRIPTION

CAUTION: Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool.

Switch action

WARNING: Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released.

WARNING: Switch can be locked in "ON" position for ease of operator comfort during extended use. Apply caution when locking tool in "ON" position and maintain firm grasp on tool.

To start the tool, simply pull the switch trigger. Release the switch trigger to stop. For continuous operation, pull the switch trigger, push in the lock button and then release the switch trigger. To stop the tool from the locked position, pull the trigger fully, then release it.

For continuous operation, pull the switch trigger, push in the lock button and then release the switch trigger. To stop the tool from the locked position, pull the switch trigger fully, then release it.

► Fig.1: 1. Switch trigger 2. Lock button

Adjusting the shoe

When the blade loses its cutting efficiency in one place along its cutting edge, reposition the shoe to utilize a sharp, unused portion of its cutting edge. This will help to lengthen the life of the blade.

To reposition the shoe, push the shoe button in the "A" direction with a click and reposition as shown in the figure which allows you to make five-way adjustment. To secure the shoe, push the shoe button in the "B" direction with a click.

►Fig.2: 1. Shoe 2. Shoe button

►Fig.3: 1. Shoe button 2. Shoe

5 ENGLISH