Makita LXSF01, LXSF01Z User Manual

INSTRUCTION MANUAL
MANUEL D'INSTRUCTION
MANUAL DE INSTRUCCIONES

Cordless Screwdriver
Visseuse sans Fil
Atornillador Inalámbrico

LXSF01
LXSF02

IMPORTANT: Read Before Using.
IMPORTANT: Lire avant usage.
IMPORTANTE: Leer antes de usar.

011811

1

ENGLISH (Original instructions)

SPECIFICATIONS

Capacities Drywall screw 4 mm (5/32") 4 mm (5/32")

Overall length

• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.

• Specifications and battery cartridge may differ from country to country.

• Weight, with battery cartridge, according to EPTA-Procedure 01/2003

General Power Tool Safety
Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or
serious injury.

Save all warnings and
instructions for future reference.

The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate power tools in explosive

atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.

Electrical Safety

4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

5. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.

Model LXSF01 LXSF02

No load speed (RPM) 0 - 4,000 /min 0 - 4,000 /min

Net weight 1.5 kg (3.3 lbs) 1.4 kg (3.2 lbs)

Rated voltage D.C. 18 V D.C. 14.4 V

Standard battery cartridges BL1815, BL1830 BL1415, BL1430

With short locator 281 mm (11-1/8") 281 mm (11-1/8")

With long locator 296 mm (11-5/8") 296 mm (11-5/8")

GEA006-2

7. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords

increase the risk of electric shock.

8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.

9. If operating a power tool in a damp location is

unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of an

GFCI reduces the risk of electric shock.

Personal Safety

10. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while

operating power tools may result in serious
personal injury.

11. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.

12. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with

your finger on the switch or energising power tools
that have the switch on invites accidents.

13. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.

14. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.

2

15. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes,

jewellery or long hair can be caught in moving
parts.

16. If devices are provided for the connection of

dust extraction and collection facilities,
ensure these are connected and properly used.

Use of dust collection can reduce dust-related
hazards.

Power tool use and care

17. Do not force the power tool. Use the correct
power tool for your application. The correct

power tool will do the job better and safer at the
rate for which it was designed.

18. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.

19. Disconnect the plug from the power source

and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such

preventive safety measures reduce the risk of
starting the power tool accidentally.

20. Store idle power tools out of the reach of

children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are

dangerous in the hands of untrained users.

21. Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

22. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.

23. Use the power tool, accessories and tool bits

etc. in accordance with these instructions,
taking into account the working conditions
and the work to be performed. Use of the power

tool for operations different from those intended
could result in a hazardous situation.

Battery tool use and care

24. Recharge only with the charger specified by
the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of fire
when used with another battery pack.

25. Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.

26. When battery pack is not in use, keep it away

from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery

terminals together may cause burns or a fire.

27. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may

cause irritation or burns.

Service

28. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power

tool is maintained.

29. Follow instruction for lubricating and

changing accessories.

30. Keep handles dry, clean and free from oil and
grease.

GEB050-2

CORDLESS SCREWDRIVER
SAFETY WARNINGS

1. Hold power tool by insulated gripping
surfaces, when performing an operation
where the fastener may contact hidden wiring.

Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.

2. Always be sure you have a firm footing.

Be sure no one is below when using the tool in
high locations.

3. Hold the tool firmly.

4. Keep hands away from rotating parts.

5. Do not touch the bit or the workpiece

immediately after operation; they may be
extremely hot and could burn your skin.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this
instruction manual may cause serious personal
injury.

3

ENC007-7

IMPORTANT SAFETY
INSTRUCTIONS

FOR BATTERY CARTRIDGE

1. Before using battery cartridge, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product
using battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.

4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical
attention right away. It may result in loss of
your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any

conductive material.

(2) Avoid storing battery cartridge in a

container with other metal objects such as
nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.
A battery short can cause a large current flow,
overheating, possible burns and even a
breakdown.

6. Do not store the tool and battery cartridge in
locations where the temperature may reach or
exceed 50 ﾟ C (122 ﾟ F).

7. Do not incinerate the battery cartridge even if
it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.

8. Be careful not to drop or strike battery.

9. Do not use a damaged battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before
completely discharged.
Always stop tool operation and charge the
battery cartridge when you notice less tool
power.

2. Never recharge a fully charged battery
cartridge.
Overcharging shortens the battery service life.

3. Charge the battery cartridge with room
temperature at 10 ﾟ C - 40 ﾟ C (50 ﾟ F - 104 ﾟ F).
Let a hot battery cartridge cool down before
charging it.

4. Charge the battery cartridge once in every six
months if you do not use it for a long period of
time.

USD301-1

Symbols

The followings show the symbols used for tool.

･ volts

･ direct current

･ no load speed

･ revolutions or reciprocation per minute

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before adjusting or
checking function on the tool.

Installing or removing battery cartridge

1

2

011812

Always switch off the tool before installing or

•

removing of the battery cartridge.

• To remove the battery cartridge, slide it from the

tool while sliding the button on the front of the
cartridge.

• To install the battery cartridge, align the tongue on

the battery cartridge with the groove in the housing
and slip it into place. Always insert it all the way
until it locks in place with a little click. If you can see
the red indicator on the upper side of the button, it is
not locked completely. Install it fully until the red
indicator cannot be seen. If not, it may accidentally
fall out of the tool, causing injury to you or someone
around you.

• Do not use force when installing the battery

cartridge. If the cartridge does not slide in easily, it
is not being inserted correctly.

1. Red indicator

2. Button

3. Battery cartridge

3

4

Battery protection system (Battery cartridge
with a star mark)

1

011389

The battery cartridge with a star mark is equipped with
the protection system, which automatically cuts off the
output power for its long service life.
The tool stops during operation when the tool and/or
battery are placed under the following situation. This is
caused by the activation of protection system and does
not show the tool trouble.

• When the tool is overloaded:

At this time, release the switch trigger,
remove the battery cartridge and remove
causes of overload and then pull the switch
trigger again to restart.

• When battery cells get hot:

If any operation of the switch trigger, the
motor will remain stopped. At this time, stop
use of the tool and cool or charge the battery
cartridge after removing it from the tool.

• When the remaining battery capacity gets low:

If any operation of the switch trigger, the
motor will remain stopped. At this time,
remove the battery cartridge from the tool and
charge it .

1. Star mark

Switch action

1. Switch trigger

NOTE:

• Even with the switch on and motor running, the bit

will not rotate until you fit the point of the bit in the
screw head and apply forward pressure to engage
the clutch.

Electric brake

This tool is equipped with an electric brake. If the tool
consistently fails to quickly stop after switch trigger
release, have tool serviced at a Makita service center.

Lighting up the front lamp

1

011817

CAUTION:

• Do not look in the light or see the source of light

directly.
Pull the switch trigger to light up the lamp. The lamp
keeps on lighting while the switch trigger is being pulled.
The lamp goes out 10 -15 seconds after releasing the
trigger.

NOTE:

• Use a dry cloth to wipe the dirt off the lens of lamp.

Be careful not to scratch the lens of lamp, or it may

lower the illumination.

1. Lamp

Reversing switch action

1. Reversing switch
lever

AB

1

011816

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates
properly and returns to the "OFF" position when

released.
To start the tool, simply pull the switch trigger. Tool speed
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop.

1

011818

This tool has a reversing switch to change the direction of
rotation. Depress the reversing switch lever from the A
side for clockwise rotation or from the B side for
counterclockwise rotation.
When the reversing switch lever is in the neutral position,
the switch trigger cannot be pulled.

CAUTION:

• Always check the direction of rotation before

operation.

5

• Use the reversing switch only after the tool comes

to a complete stop. Changing the direction of

rotation before the tool stops may damage the tool.
When not operating the tool, always set the reversing
switch lever to the neutral position.

Depth adjustment

1. Locator

A

1

B

011813

The depth can be adjusted by turning the locator. Turn it
in "B" direction for less depth and in "A" direction for more
depth. One full turn of the locator equals 2 mm (1/16")
change in depth.

3 mm (1/8")

1

011827

Adjust the locator so that the distance between the tip of
the locator and the screw head is approximately 3 mm
(1/8") as shown in the figures. Drive a trial screw into your
material or a piece of duplicate material. If the depth is
still not suitable for the screw, continue adjusting until you
obtain the proper depth setting.

1. Locator

To remove the bit, pull the locator. Then grasp the bit with
a pair of pliers and pull the bit out of the magnetic bit
holder. Sometimes, it helps to wiggle the bit with the
pliers as you pull.

1. Locator

2. Bit

2

3

011820

To install the bit, push it firmly into the magnetic bit holder.
Then install the locator by pushing it firmly back.

1

3. Magnetic bit
holder

Hook

1. Groove

2. Hook

3. Screw

1

2

3

011821

The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool.
To install the hook, insert it into a groove in the tool
housing on either side and then secure it with a screw. To
remove, loosen the screw and then take it out.

OPERATION

Screwdriving operation

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out
any work on the tool.

Installing or removing the bit

1. Locator

1

011819

011822

Fit the screw on the point of the bit and place the point of
the screw on the surface of the workpiece to be fastened.
Apply pressure to the tool and start it. Withdraw the tool
as soon as the clutch cuts in. Then release the switch
trigger.

CAUTION:

• When fitting the screw onto the point of the bit, be

careful not to push in on the screw. If the screw is

6

pushed in, the clutch will engage and the screw will
rotate suddenly. This could damage a workpiece or
cause an injury.

• Make sure that the bit is inserted straight in the

screw head, or the screw and/or bit may be
damaged.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to
perform inspection or maintenance.

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may

result.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized or Factory Service Centers, always
using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:

• These accessories or attachments are

recommended for use with your Makita tool

specified in this manual. The use of any other

accessories or attachments might present a risk of

injury to persons. Only use accessory or

attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.

• Phillips Insert bits

• Magnetic bit holder

• Various type of Makita genuine batteries and

chargers

• Plastic carrying case

NOTE:

Some items in the list may be included in the tool
package as standard accessories. They may differ from
country to country.

MAKITA LIMITED ONE YEAR WARRANTY

Warranty Policy

Every Makita tool is thoroughly inspected and tested
before leaving the factory. It is warranted to be free of
defects from workmanship and materials for the period
of ONE YEAR from the date of original purchase.
Should any trouble develop during this one year period,
return the COMPLETE tool, freight prepaid, to one of
Makita’s Factory or Authorized Service Centers. If
inspection shows the trouble is caused by defective
workmanship or material, Makita will repair (or at our
option, replace) without charge.

This Warranty does not apply where:

repairs have been made or attempted by others:
repairs are required because of normal wear and
tear:
the tool has been abused, misused or improperly
maintained:
alterations have been made to the tool.

IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY
INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES FROM THE SALE OR USE OF THE
PRODUCT. THIS DISCLAIMER APPLIES BOTH
DURING AND AFTER THE TERM OF THIS
WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED
WARRANTIES, INCLUDING IMPLIED WARRANTIES
OF "MERCHANTABILITY" AND "FITNESS FOR A
SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM
OF THIS WARRANTY.
This Warranty gives you specific legal rights, and you
may also have other rights which vary from state to
state. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you.
Some states do not allow limitation on how long an
implied warranty lasts, so the above limitation may not
apply to you.

EN0006-1

7

FRANÇAIS (Mode d’emploi original)

SPÉCIFICATIONS

Capacités Vis de plaque de plâtre 4 mm (5/32") 4 mm (5/32")

Longueur totale

• Étant donné l'évolution constante de notre programme de recherche et de développement, les spécifications contenues dans ce
manuel sont sujettes à modification sans préavis.

• Les caractéristiques techniques et la batterie peuvent varier suivant les pays.

• Poids, batterie comprise, conforme à la procédure EPTA de 01/2003

Consignes de sécurité générales
pour outils électriques

MISE EN GARDE Veuillez lire toutes les mises en

garde de sécurité et toutes les instructions.

L'ignorance des mises en garde et des instructions
comporte un risque de choc électrique, d'incendie et/ou
de blessure grave.

Conservez toutes les mises en
garde et instructions pour
référence future.

Le terme ≪ outil électrique ≫ qui figure dans les
avertissements fait référence à un outil électrique
branché sur une prise de courant (par un cordon
d'alimentation) ou alimenté par batterie (sans fil).

Sécurité de la zone de travail

1. Maintenez la zone de travail propre et bien
éclairée. Les zones de travail encombrées ou

sombres ouvrent grande la porte aux accidents.

2. N'utilisez pas les outils électriques dans les

atmosphères explosives, par exemple en
présence de liquides, gaz ou poussières
inflammables. Les outils électriques produisent

des étincelles au contact desquelles la poussière
ou les vapeurs peuvent s'enflammer.

3. Assurez-vous qu'aucun enfant ou curieux ne

s'approche pendant que vous utilisez un outil
électrique. Vous risquez de perdre la maîtrise de

l'outil si votre attention est détournée.

Sécurité en matière d'électricité

4. Les fiches d'outil électrique sont conçues
pour s'adapter parfaitement aux prises de
courant. Ne modifiez jamais la fiche de
quelque façon que ce soit. N'utilisez aucun

Modèle LXSF01 LXSF02

Vitesse à vide (T/MIN) 0 - 4 000 /min. 0 - 4 000 /min.

Tension nominale C.C. 18 V C.C. 14,4 V

Batteries standard BL1815, BL1830 BL1415, BL1430

Avec positionneur court 281 mm (11-1/8") 281 mm (11-1/8")

Avec positionneur long 296 mm (11-5/8") 296 mm (11-5/8")

Poids net 1,5 kg (3,3 lbs) 1,4 kg (3,2 lbs)

GEA006-2

adaptateur de fiche sur les outils électriques
avec mise à la terre. En ne modifiant pas les

fiches et en les insérant dans des prises de
courant pour lesquelles elles ont été conçues vous
réduirez les risques de choc électrique.

5. Évitez tout contact corporel avec les surfaces

mises à la terre, telles que les tuyaux,
radiateurs, cuisinières et réfrigérateurs. Le

risque de choc électrique est plus élevé si votre
corps se trouve mis à la terre.

6. N'exposez pas les outils électriques à la pluie
ou à l'eau. La présence d'eau dans un outil
électrique augmente le risque de choc électrique.

7. Ne maltraitez pas le cordon. N'utilisez jamais

le cordon pour transporter, tirer ou
débrancher l'outil électrique. Maintenez le
cordon à l'écart des sources de chaleur, de
l'huile, des objets à bords tranchants et des
pièces en mouvement. Le risque de choc

électrique est plus élevé lorsque les cordons sont
endommagés ou enchevêtrés.

8. Lorsque vous utilisez un outil électrique à

l'extérieur, utilisez un cordon prolongateur
prévu à cette fin. Les risques de choc électrique

sont moindres lorsqu'un cordon conçu pour
l'extérieur est utilisé.

9. Si vous devez utiliser un outil électrique dans

un endroit humide, utilisez une source
d'alimentation protégée par un disjoncteur de
fuite à la terre. L'utilisation d'un disjoncteur de

fuite à la terre réduit le risque de choc électrique.

Sécurité personnelle

10. Restez alerte, attentif à vos mouvements et
faites preuve de bon sens lorsque vous
utilisez un outil électrique. Évitez d'utiliser un
outil électrique si vous êtes fatigué ou si vous
avez pris une drogue, de l'alcool ou un

8