Makita LXDT01 User Manual

INSTRUCTION MANUAL
MANUEL D'INSTRUCTION
MANUAL DE INSTRUCCIONES

Cordless Impact Driver
Tournevis à Chocs sans Fil
Atornillador de Impacto Inalámbrico

LXDT01

IMPORTANT: Read Before Using.
IMPORTANT: Lire avant usage.
IMPORTANTE: Leer antes de usar.

0111 85

1

ENGLISH (Original instructions)

SPECIFICATIONS

Model LXDT01

Capacities

No load speed (RPM)

Impacts per minute

Overall length 139 mm (5-1/2")

Net weight (with battery cartridge) 1.3 kg ( 2.8 lbs)

Rated voltage D.C.18 V

Standard battery cartridge BL1815/BL1830

• Due to our continuing programme of research and development, the specifications herein are subject to change without notice.

• Specifications and battery cartridge may differ from country to country.

• Weight, with battery cartridge, according to EPTA-Procedure 01/2003

General Power Tool Safety
Warnings

WARNING Read all safety warnings and all

instructions. Failure to follow the warnings and

instructions may result in electric shock, fire and/or
serious injury.

Save all warnings and
instructions for future reference.

The term "power tool" in the warnings refers to your
mains-operated (corded) power tool or battery-operated
(cordless) power tool.

Work area safety

1. Keep work area clean and well lit. Cluttered or

dark areas invite accidents.

2. Do not operate power tools in explosive

atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools

create sparks which may ignite the dust or fumes.

3. Keep children and bystanders away while
operating a power tool. Distractions can cause
you to lose control.

Electrical Safety

4. Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will

reduce risk of electric shock.

Machine screw 4 mm - 8 mm (5/32" - 5/16")

Standard bolt 5 mm - 14 mm (3/16" - 9/16")

High tensile bolt 5 mm - 12 mm (3/16" - 1/2")

Hammer mode (Hard) 0 - 2,600/min.

Hammer mode (Medium) 0 - 2,000/min.

Hammer mode (Soft) 0 - 1,300/min.

Hammer mode (Hard) 0 - 3,400

Hammer mode (Medium) 0 - 2,800

Hammer mode (Soft) 0 - 1,300

GEA006-2

5. Avoid body contact with earthed or grounded

surfaces such as pipes, radiators, ranges and
refrigerators. There is an increased risk of

electric shock if your body is earthed or grounded.

6. Do not expose power tools to rain or wet
conditions. Water entering a power tool will
increase the risk of electric shock.

7. Do not abuse the cord. Never use the cord for

carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords

increase the risk of electric shock.

8. When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of
a cord suitable for outdoor use reduces the risk of
electric shock.

9. If operating a power tool in a damp location is

unavoidable, use a ground fault circuit
interrupter (GFCI) protected supply. Use of an

GFCI reduces the risk of electric shock.

Personal Safety

10. Stay alert, watch what you are doing and use
common sense when operating a power tool.
Do not use a power tool while you are tired or
under the influence of drugs, alcohol or
medication. A moment of inattention while

operating power tools may result in serious
personal injury.

11. Use personal protective equipment. Always
wear eye protection. Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions

2

will reduce personal injuries.

12. Prevent unintentional starting. Ensure the

switch is in the off-position before connecting
to power source and/or battery pack, picking
up or carrying the tool. Carrying power tools with

your finger on the switch or energising power tools
that have the switch on invites accidents.

13. Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may
result in personal injury.

14. Do not overreach. Keep proper footing and
balance at all times. This enables better control
of the power tool in unexpected situations.

15. Dress properly. Do not wear loose clothing or

jewellery. Keep your hair, clothing, and gloves
away from moving parts. Loose clothes,

jewellery or long hair can be caught in moving
parts.

16. If devices are provided for the connection of

dust extraction and collection facilities,
ensure these are connected and properly used.

Use of dust collection can reduce dust-related
hazards.

Power tool use and care

17. Do not force the power tool. Use the correct
power tool for your application. The correct

power tool will do the job better and safer at the
rate for which it was designed.

18. Do not use the power tool if the switch does
not turn it on and off. Any power tool that cannot
be controlled with the switch is dangerous and
must be repaired.

19. Disconnect the plug from the power source

and/or the battery pack from the power tool
before making any adjustments, changing
accessories, or storing power tools. Such

preventive safety measures reduce the risk of
starting the power tool accidentally.

20. Store idle power tools out of the reach of

children and do not allow persons unfamiliar
with the power tool or these instructions to
operate the power tool. Power tools are

dangerous in the hands of untrained users.

21. Maintain power tools. Check for misalignment

or binding of moving parts, breakage of parts
and any other condition that may affect the
power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

22. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.

23. Use the power tool, accessories and tool bits

etc. in accordance with these instructions,

taking into account the working conditions
and the work to be performed. Use of the power

tool for operations different from those intended
could result in a hazardous situation.

Battery tool use and care

24. Recharge only with the charger specified by
the manufacturer. A charger that is suitable for

one type of battery pack may create a risk of fire
when used with another battery pack.

25. Use power tools only with specifically
designated battery packs. Use of any other
battery packs may create a risk of injury and fire.

26. When battery pack is not in use, keep it away

from other metal objects, like paper clips,
coins, keys, nails, screws or other small metal
objects, that can make a connection from one
terminal to another. Shorting the battery

terminals together may cause burns or a fire.

27. Under abusive conditions, liquid may be

ejected from the battery; avoid contact. If
contact accidentally occurs, flush with water.
If liquid contacts eyes, additionally seek
medical help. Liquid ejected from the battery may

cause irritation or burns.

Service

28. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power

tool is maintained.

29. Follow instruction for lubricating and

changing accessories.

30. Keep handles dry, clean and free from oil and
grease.

GEB054-1

CORDLESS IMPACT DRIVER
SAFETY WARNINGS

1. Hold power tool by insulated gripping
surfaces, when performing an operation
where the fastener may contact hidden wiring.

Fasteners contacting a "live" wire may make
exposed metal parts of the power tool "live" and
could give the operator an electric shock.

2. Always be sure you have a firm footing.

Be sure no one is below when using the tool in
high locations.

3. Hold the tool firmly.

4. Wear ear protectors.

SAVE THESE INSTRUCTIONS.

WARNING:

DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence

3

to safety rules for the subject product.
MISUSE or failure to follow the safety rules stated in
this instruction manual may cause serious personal
injury.

USD302-1

Symbols

The followings show the symbols used for tool.

･ volts

･ direct current

･ no load speed

･ revolutions or reciprocation per minute

･ number of blow

ENC007-5

IMPORTANT SAFETY
INSTRUCTIONS

FOR BATTERY CARTRIDGE

1. Before using battery cartridge, read all
instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product
using battery.

2. Do not disassemble battery cartridge.

3. If operating time has become excessively

shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.

4. If electrolyte gets into your eyes, rinse them
out with clear water and seek medical
attention right away. It may result in loss of
your eyesight.

5. Do not short the battery cartridge:

(1) Do not touch the terminals with any

conductive material.

(2) Avoid storing battery cartridge in a

container with other metal objects such as
nails, coins, etc.

(3) Do not expose battery cartridge to water

or rain.
A battery short can cause a large current
flow, overheating, possible burns and

6. Do not store the tool and battery cartridge in

7. Do not incinerate the battery cartridge even if

8. Be careful not to drop or strike battery.

even a breakdown.

locations where the temperature may reach or
exceed 50 ﾟ C (122 ﾟ F).

it is severely damaged or is completely worn
out. The battery cartridge can explode in a fire.

9. Do not use a damaged battery.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

1. Charge the battery cartridge before
completely discharged.
Always stop tool operation and charge the
battery cartridge when you notice less tool
power.

2. Never recharge a fully charged battery
cartridge.
Overcharging shortens the battery service life.

3. Charge the battery cartridge with room
temperature at 10 ﾟ C - 40 ﾟ C (50 ﾟ F - 104 ﾟ F).
Let a hot battery cartridge cool down before
charging it.

FUNCTIONAL DESCRIPTION

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before adjusting or
checking function on the tool.

Installing or removing battery cartridge

1

2

009204

Always switch off the tool before insertion or

•

removal of the battery cartridge.

• To remove the battery cartridge, withdraw it from

the tool while sliding the button on the front of the
cartridge.

• To insert the battery cartridge, align the tongue on

the battery cartridge with the groove in the housing
and slip it into place. Always insert it all the way
until it locks in place with a little click. If you can see
the red part on the upper side of the button, it is not
locked completely. Insert it fully until the red part
cannot be seen. If not, it may accidentally fall out of
the tool, causing injury to you or someone around
you.

• Do not use force when inserting the battery

cartridge. If the cartridge does not slide in easily, it
is not being inserted correctly.

1. Red part

2. Button

3. Battery cartridge

3

4

Switch action

1. Switch trigger

1

009208

CAUTION:

• Before inserting the battery cartridge into the tool,

always check to see that the switch trigger actuates
properly and returns to the "OFF" position when

released.
To start the tool, simply pull the switch trigger. Tool speed
is increased by increasing pressure on the switch trigger.
Release the switch trigger to stop.

NOTE:

• Continuing to pull the trigger switch for more than

130 seconds will stop the tool.

Electric brake

This tool is equipped with an electric brake. If the tool
consistently fails to quickly stop after switch trigger
release, have tool serviced at a Makita service center.

Lighting up the front lamp

CAUTION:

• Do not look in the light or see the source of light

directly.

1. Lamp

1

009209

SH

1. Light button

ON to the OFF and from the OFF to the ON.
With the light button in the ON status, pull the switch
trigger to turn on the light. To turn off, release it and the
light goes out approximately 10 seconds after releasing.
With the light button in the OFF status, even if the trigger
is pulled, the lamp will not light on.

NOTE:

• To make sure the status of light, pull the trigger.

When the lamp lights up by pulling the switch
trigger, the light switch is in the ON status. When
the lamp does not come on, the light switch is in the
OFF status.

• During the operation of switch trigger, the light

status cannot be changed.

• For approximately 10 seconds after releasing the

switch trigger, the light status can be switched.

Reversing switch action

1. Reversing switch
lever

A

1

009211

This tool has a reversing switch to change the direction of
rotation. Depress the reversing switch lever from the A
side for clockwise rotation or from the B side for
counterclockwise rotation.
When the reversing switch lever is in the neutral position,
the switch trigger cannot be pulled.

CAUTION:

• Always check the direction of rotation before

operation.

• Use the reversing switch only after the tool comes

to a complete stop. Changing the direction of
rotation before the tool stops may damage the tool.

• When not operating the tool, always set the

reversing switch lever to the neutral position.

B

1

011216

Every time the light button on the switch panel is
pressed, the light status is alternatively changed from the

5

Changing the hammering force

2

3

4

011217

SH

SH

SH

1

SH

5

1. Changed in
three steps

2. Hard

3. Medium

4. Soft

5. Hammering
force button

Hammering force grade
displayed on panel

Maximum blows

Hard

SH

3,400 /min.

Tightening when force
and speed are desired.

Medium

SH

Soft

SH

2,800 /min.

1,300 /min.

Tightening when a good
finishing is needed.

Tightening when excessive
tightening need to be avoided
because of potentially clogged
female screw and broken or
damaged screw head.

011268

The hammering force can be changed in three steps:
hard, medium and soft.
This allows a tightening suitable to the work.
Every time the hammering force button

is pressed, the
number of blows changes in three steps.
For approximately one minute after releasing the switch
trigger, the hammering force can be changed.

NOTE:

• When all lamps on the switch panel go out, the tool

is turned off to save the battery power. The hammer
force grade can be checked by pulling the switch
trigger to the extent that the tool does not operate.

• During the operation of switch trigger, the hammer

force grade cannot be changed.

Application Work

Tightening in underwork
material/ Tightening long
screws/ Tightening bolts.

Tightening in the finishing
board, plaster board.

Tightening sash screw/
Tightening small screws
such as M6.

Empty signal for remaining
battery capacity

1. LED indicator

SH

1

011220

Pulling the trigger switch when the remaining battery
capacity become very low makes LED indicator flicker.
If the tool is used continuously with the LED indicator

6

flickering up and the battery power is almost used up, the
LED indicator will light up and the tool itself will stop
Please refer to the following table for the LED indicator
status and the remaining battery capacity.

1. Bit

2. Sleeve

LED indicator status

OFF

Flickering

Lighting on

0111 88

Remaining battery capacity

Enough

20%

Very low and the tool will stops

NOTE:

• When all lamps on the switch panel go out, the tool

is turned off to save the battery power. The
remaining battery capacity can be checked by
pulling the switch trigger to the extent that the tool
does not operate.

• All of the lamps on the switch panel go out

approximately one minute after releasing the switch
trigger.

• When the tool temperature is high, the LED

indicator may flicker or light up.

• If the LED indicator lights up and the tool stops

even with a recharged battery cartridge, cool down
the tool temperature fully. When the status is still
unchanged, stop using and have the tool repaired
by a Makita local service center.

ASSEMBLY

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before carrying out
any work on the tool.

Installing or removing driver bit or socket bit

12 mm
(15/32”)

9 mm
(3/8”)

1

2

009205

To install the bit, insert the bit into the sleeve as far as it
will go.
To remove the bit, pull the sleeve in the direction of the
arrow and pull the bit out.

NOTE:

• If the bit is not inserted deep enough into the sleeve,

the sleeve will not return to its original position and
the bit will not be secured. In this case, try
re-inserting the bit according to the instructions
above.

• When it is difficult to insert the bit, pull the sleeve

and insert it into the sleeve as for as it will go.

• After inserting the bit, make sure that it is firmly

secured. If it comes out, do not use it.

Hook

1. Groove

2. Hook

1

3. Screw

2

3

0111 86

The hook is convenient for temporarily hanging the tool.
This can be installed on either side of the tool.
To install the hook, insert it into a groove in the tool
housing on either side and then secure it with a screw. To
remove, loosen the screw and then take it out.

OPERATION

001266

Use only the driver bit or socket bit shown in the figure.
Do not use any other driver bit or socket bit.

009222

The proper fastening torque may differ depending upon
the kind or size of the screw/bolt, the material of the

7

workpiece to be fastened, etc. The relation between
fastening torque and fastening time is shown in the
figures.

N.m

Standard bolt

(ft.lbs)

120

(87)

100

(72)

80

(58)

60

(43)

40

(29)

Fastening torque

20

(14)

0 1.0 2.0 3.0

Fastening time

009220

N.m

(ft.lbs)

120
(87)

100
(72)

80

(58)

60

(43)

Fastening torque

40

(29)

20

(14)

0 1.0 2.0 3.0
Fastening time

009221

M10

(5/16")

M8

High tensile bolt

M8

(3/8")

M12

M10

(3/8")

(5/16")

M12

(1/2")

M14

(9/16")

(1/2")

(M14)

(9/16")

(M12)

(1/2")

(M10)
(3/8")
(M8)
(5/16")

(S)

(M12)

(M10)
(3/8")

(M8)

(5/16")

(1/2")

(S)

Proper fastening torque

Proper fastening torque

Hold the tool firmly and place the point of the driver bit in
the screw head. Apply forward pressure to the tool to the
extent that the bit will not slip off the screw and turn the
tool on to start operation.

NOTE:

• Use the proper bit for the head of the screw/bolt

that you wish to use.

• When fastening screw M8 or smaller, choose a

proper hammer force carefully adjust pressure on
the switch trigger so that the screw is not damaged.

• Hold the tool pointed straight at the screw.

• If the hammering force is too strong you tighten the

screw for a time longer than shown in the figures,
the screw or the point of the driver bit may be
overstressed, stripped, damaged, etc. Before

starting your job, always perform a test operation to

determine the proper fastening time for your screw.
The fastening torque is affected by a wide variety of
factors including the following. After fastening, always
check the torque with a torque wrench.

1. When the battery cartridge is discharged almost
completely, voltage will drop and the fastening
torque will be reduced.

2. Driver bit or socket bit
Failure to use the correct size driver bit or socket
bit will cause a reduction in the fastening torque.

3. Bolt

• Even though the torque coefficient and the

class of bolt are the same, the proper fastening
torque will differ according to the diameter of
bolt.

• Even though the diameters of bolts are the

same, the proper fastening torque will differ
according to the torque coefficient, the class of
bolt and the bolt length.

4. The manner of holding the tool or the material of
driving position to be fastened will affect the
torque.

5. Operating the tool at low speed will cause a
reduction in the fastening torque.

MAINTENANCE

CAUTION:

• Always be sure that the tool is switched off and the

battery cartridge is removed before attempting to
perform inspection or maintenance except for the
following troubleshooting related to the light.

Cleaning

From time to time wipe off the outside (tool body) of the
tool using a cloth dampened in soapy water.

CAUTION:

• Never use gasoline, benzine, thinner, alcohol or the

like. Discoloration, deformation or cracks may
result.

8

Troubleshooting

Trouble Light status/LED indicator status/tool status Steps to be taken

Remaining battery capacity level is low.
Charge the battery cartridge.

When the LED indicator still lights up

even after charging the battery cartridge,
LED indicator for empty signal for
remaining battery capacity lights up.

The tool stops
during operation.

0111 87

Light flickers once per second.

Light flickers five times per second

Switch trigger has been pulled
continuously for more than 130 seconds.

Other Symptoms

To maintain product SAFETY and RELIABILITY, repairs,
any other maintenance or adjustment should be
performed by Makita Authorized or Factory Service
Centers, always using Makita replacement parts.

.

the tool temperature is high.

Cool down it fully. The tool restarts after

temperature becomes low.

When the status is still unchanged, stop

using and have the tool repaired by a

Makita local service center.

The tool temperature is high. Cool down

fully. The tool restarts after its temperature

it

becomes low.

Use the tool with the motor not locked.

(When the tool has stopped due to the

motor locking, withdraw the battery

cartridge one time and then insert it again

or release the switch trigger for more than

60 seconds to restart the tool.)

If the motor still remains locked, stop using

and have the tool repaired by a Makita

local service center.

Release the switch trigger.

Stop using and have the

a Makita local service center.

its

tool repaired by

ACCESSORIES

CAUTION:

• These accessories or attachments are

recommended for use with your Makita tool
specified in this manual. The use of any other
accessories or attachments might present a risk of
injury to persons. Only use accessory or

attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.

• Screw bits

• Hook

• Plastic carrying case

• Various type of Makita genuine batteries and

chargers

9

MAKITA LIMITED ONE YEAR WARRANTY

Warranty Policy

Every Makita tool is thoroughly inspected and tested
before leaving the factory. It is warranted to be free of
defects from workmanship and materials for the period
of ONE YEAR from the date of original purchase.
Should any trouble develop during this one year period,
return the COMPLETE tool, freight prepaid, to one of
Makita’s Factory or Authorized Service Centers. If
inspection shows the trouble is caused by defective
workmanship or material, Makita will repair (or at our
option, replace) without charge.

This Warranty does not apply where:

repairs have been made or attempted by others:
repairs are required because of normal wear and
tear:
the tool has been abused, misused or improperly
maintained:
alterations have been made to the tool.

IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY
INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES FROM THE SALE OR USE OF THE
PRODUCT. THIS DISCLAIMER APPLIES BOTH
DURING AND AFTER THE TERM OF THIS
WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED
WARRANTIES, INCLUDING IMPLIED WARRANTIES
OF "MERCHANTABILITY" AND "FITNESS FOR A
SPECIFIC PURPOSE," AFTER THE ONE YEAR TERM
OF THIS WARRANTY.
This Warranty gives you specific legal rights, and you
may also have other rights which vary from state to
state. Some states do not allow the exclusion or
limitation of incidental or consequential damages, so
the above limitation or exclusion may not apply to you.
Some states do not allow limitation on how long an
implied warranty lasts, so the above limitation may not
apply to you.

EN0006-1

10