Makita JS8000 Owner's Manual

INSTRUCTION MANUAL MANUEL D'INSTRUCTION MANUAL DE INSTRUCCIONES
Cement Shear Coupe du Ciment Corte de Cemento con Cizalla
JS8000
007430
DOUBLE INSULATION DOUBLE ISOLATION DOBLE AISLAMIENTO
WARNING:
For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
AVERTISSEMENT:
Pour votre propre sécurité, prière de lire attentivement avant l’utilisation. GARDER CES INSTRUCTIONS POUR RÉFÉRENCE ULTÉRIEURE.
ADVERTENCIA:
Para su seguridad personal, LEA DETENIDAMENTE este manual antes de usar la herramienta. GUARDE ESTAS INSTRUCCIONES PARA FUTURA REFERENCIA.
ENGLISH
SPECIFICATIONS
Model JS8000
Max. cutting capacities Fiber cement material 8 mm (5/16”)
Strokes per minute 0 - 2,500/min.
Overall length 346 mm (13-5/8”)
Net weight 2.1 kg (4.6 lbs)
Due to our continuing programme of research and development, the specifications herein are subject to change without notice.
Note: Specifications may differ from country to country.
GENERAL SAFETY RULES
USA002-2
(For All Tools)
WARNING:
Read and understand all instructions.
Failure to follow all instructions listed below, may result in electric shock, fire and/or seri­ous personal injury.
SAVE THESE INSTRUCTIONS
Work Area
1. Keep your work area clean and well lit. Cluttered
benches and dark areas invite accidents.
2. Do not operate power tools in explosive atmo-
spheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks
which may ignite the dust or fumes.
3. Keep bystanders, children, and visitors away
while operating a power tool. Distractions can
cause you to lose control.
Electrical Safety
4. Double insulated tools are equipped with a
polarized plug (one blade is wider than the other.) This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install a polarized outlet. Do not change the plug in any way. Double insula-
tion eliminates the need for the three wire grounded power cord and grounded power supply system.
5. Avoid body contact with grounded surfaces
such as pipes, radiators, ranges and refrigera­tors. There is an increased risk of electric shock if
your body is grounded.
6. Do not expose power tools to rain or wet condi­tions. Water entering a power tool will increase the
risk of electric shock.
7. Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace damaged cords immedi­ately. Damaged cords increase the risk of electric
shock.
8. When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W”.
These cords are rated for outdoor use and reduce the risk of electric shock.
Personal Safety
9. Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medication. A moment of inat-
tention while operating power tools may result in serious personal injury.
10. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, cloth­ing, and gloves away from moving parts. Loose
clothes, jewelry, or long hair can be caught in mov­ing parts.
11. Avoid accidental starting. Be sure switch is off before plugging in. Carrying tools with your finger
on the switch or plugging in tools that have the switch on invites accidents.
12. Remove adjusting keys or wrenches before turn­ing the tool on. A wrench or a key that is left
attached to a rotating part of the tool may result in personal injury.
13. Do not overreach. Keep proper footing and bal­ance at all times. Proper footing and balance
enables better control of the tool in unexpected situ­ations.
14. Use safety equipment. Always wear eye protec­tion. Dust mask, non-skid safety shoes, hard hat, or
hearing protection must be used for appropriate con­ditions. Ordinary eye or sun glasses are NOT eye protection.
2
Tool Use and Care
15. Use clamps or other practical way to secure and support the workpiece to a stable platform. Hold-
ing the work by hand or against your body is unsta­ble and may lead to loss of control.
16. Do not force tool. Use the correct tool for your application. The correct tool will do the job better
and safer at the rate for which it is designed.
17. Do not use tool if switch does not turn it on or off. Any tool that cannot be controlled with the
switch is dangerous and must be repaired.
18. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. Such preventive
safety measures reduce the risk of starting the tool accidentally.
19. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in
the hands of untrained users.
20. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with
sharp cutting edges are less likely to bind and are easier to control.
21. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If damaged,
have the tool serviced before using. Many acci-
dents are caused by poorly maintained tools.
22. Use only accessories that are recommended by the manufacturer for your model. Accessories
that may be suitable for one tool, may become haz­ardous when used on another tool.
SERVICE
23. Tool service must be performed only by qualified repair personnel. Service or maintenance per-
formed by unqualified personnel could result in a risk of injury.
24. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unau-
thorized parts or failure to follow Maintenance instructions may create a risk of electric shock or injury.
USE PROPER EXTENSION CORD: Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table 1 shows the correct size to use depending on cord length and nameplate ampere rating. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord.
Table 1: Minimum gage for cord
Ampere Rating
Volts Total length of cord in feet
120 V 25 ft. 50 ft. 100 ft. 150 ft.
More Than Not More Than AWG
0 6 18 16 16 14
18 16 14 12610 10 12 16 16 14 12 12 16 14 12
Not Recommended
SPECIFIC SAFETY RULES
USB011-3
DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to shears safety rules. If you use this tool unsafely or incorrectly, you can suffer serious per­sonal injury.
1. Hold the tool firmly.
2. Secure the workpiece firmly.
3. Keep hands away from moving parts.
4. Edges and chips of the workpiece are sharp. Wear gloves. It is also recommended that you put on thickly bottomed shoes to prevent injury.
5. Do not put the tool on the chips of the work­piece. Otherwise it can cause damage and trou­ble on the tool.
6. Do not leave the tool running. Operate the tool only when hand-held.
7. Always be sure you have a firm footing. Be sure no one is below when using the tool in high locations.
8. Do not touch the blade or the workpiece immedi­ately after operation; they may be extremely hot and could burn your skin.
9. Avoid cutting electrical wires. It can cause seri­ous accident by electric shock.
3
SAVE THESE INSTRUCTIONS.
WARNING:
MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.
SYMBOLS
USD201-2
The followings show the symbols used for tool.
V............................volts
A ...........................amperes
Hz..........................hertz
....................alternating current
.......................no load speed
For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trigger fully, then release it.
Hook
The hook is convenient for temporary hanging the tool. When using the hook, pull it out in “A” direction and then push it in “B” direction to secure in place.
A
004676
1
1. Hook
004677
.......................Class II Construction
.../min....................revolutions or reciprocation per
minute
FUNCTIONAL DESCRIPTION
CAUTION:
Always be sure that the tool is switched off and
unplugged before adjusting or checking function on the tool.
Switch action
12
CAUTION:
Before plugging in the tool, always check to see
that the switch trigger actuates properly and returns to the “OFF” position when released.
Switch can be locked in “ON position for ease of
operator comfort during extended use. Apply cau­tion when locking tool in “ON” position and maintain firm grasp on tool.
To start the tool, simply pull the switch trigger. Tool speed is increased by increasing pressure on the switch trigger. Release the switch trigger to stop.
004668
1. Switch trigger
2. Lock button
B
When not using the hook, return it back to its initial posi­tion by following the above procedures in reverse.
ASSEMBLY
CAUTION:
Always be sure that the tool is switched off and
unplugged before carrying out any work on the tool.
Replacement of blades
CAUTION:
Never remove the blades with bare hands. Wear
gloves. Otherwise it can cause injury.
Removing cutting head
1
2
3
4
4
007431
1. Hex wrench
2. Loosen
3. Screws
4. Cutting head
Use the hex wrench to loosen the three screws which secure the cutting head. Pull the cutting head straight out to remove it with turning it left and right alternately.
Removing shear blades
1
007432
5
1. Side blade
2. Center blade
3. Screws
4. Side blade
2
5. Cutting head
3
4
Remove the two screws (middle and front) which hold the cutting head. When removing the middle screw, be care­ful not to lose the spacer. Then the blades can be removed easily. When removing the blades, hold the blades, the spacer and the pivot sleeve so that they do not fall from the cutting head.
Installing shear blades
1
007433
1. Side blade
2. Center blade
3. Side blade
4. Pivot sleeve
5. Spacer
4
2
3
5
Install the spacer and the pivot sleeve and tighten the three screws after inserting the center blade, side blades into the cutting head. In this process, the screw heads should be protruding 2 - 3 mm (1/16”-1/8”) from the cut­ting head surface.
If you will tighten the screws excessively, the cutting head cannot be installed to the tool.
NOTE:
Side blade edge can be used in four ways by repo-
sitioning them left-to-right and end-to-end as shown in the figure.
The following describes time and procedure to change blades.
A) When the two side blades have rounded
about half their width, they can be reposi­tioned left-to-right for new cutting edges.
B) When both edges of each side blade have
rounded about half their width, reposition them end-to-end for two new cutting edges.
C) When all edges have worn down, obtain
replacements from Makita authorized or factory service center.
D) When side blades are worn out, the center
blade should also be replaced.
2
007435
1. Reposition end­to-end
2. Reposition left­to-right
1
Installing cutting head
007436
1. Hex wrench
1
2
2. Tighten
3. Screws
3
CAUTION:
Secure the cutting head firmly. Otherwise it can
rotate during operation and can cause serious injury.
Insert the cutting head into the tool with turning it left and right alternately. Then tighten the three screws with the hex wrench.
OPERATION
CAUTION:
This tool is intended for cutting fiber cement mate-
rial only, with a thickness of 5/16 or less. Do not cut other materials or stack-cut. Doing so will dam­age the tool and void warranty.
Wear gloves. Otherwise it can cause injury.
Secure the workpiece firmly. Move the tool forward keep­ing the side blades flush with the workpiece surface.
007434
5
MAINTENANCE
CAUTION:
Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or maintenance.
Lubrication
1
4
2
5
Before operation, lubricate the contact point of the center blade and the side blades. And, also lubricate around the pivot sleeve and the spacer.
To maintain product SAFETY and RELIABILITY, repairs, carbon brush inspection and replacement, any other maintenance or adjustment should be performed by Mak­ita Authorized or Factory Service Centers, always using Makita replacement parts.
007433
1. Side blade
2. Center blade
3. Side blade
4. Pivot sleeve
5. Spacer
3
ACCESSORIES
CAUTION:
These accessories or attachments are recom-
mended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to per­sons. Only use accessory or attachment for its stated purpose.
If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
Center blade
Side blades
Hex wrench
MAKITA LIMITED ONE YEAR WARRANTY
EN0006-1
Warranty Policy
Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge.
This Warranty does not apply where:
repairs have been made or attempted by others:
repairs are required because of normal wear and
tear:
the tool has been abused, misused or improperly
maintained:
alterations have been made to the tool.
IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAM­AGES FROM THE SALE OR USE OF THE PRODUCT. THIS DISCLAIMER APPLIES BOTH DURING AND AFTER THE TERM OF THIS WARRANTY.
MAKITA DISCLAIMS LIABILITY FOR ANY IMPLIED WARRANTIES, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A SPE­CIFIC PURPOSE,” AFTER THE ONE YEAR TERM OF THIS WARRANTY.
This Warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limi­tation or exclusion may not apply to you. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.
6
Loading...
+ 14 hidden pages