Makita DML807 User Manual

GB Cordless LED Flashlight Instruction manual

F Lampe Torche LED Manuel d’instructions

LS Linterna LED Inalámbrica Manual de instrucciones

DML807

IMPORTANT: Read Before Using. IMPORTANT : Lire avant usage. IMPORTANTE: Lea antes de usar.

ENGLISH

Diagram Legend

1. Battery

2. Battery release button

3. Red indicator

4. Switch

5. Main LED (20 pcs.)

6. Sub LED (1 pc.)

7. Metal hook

8. USB power supply port

SPECIFICATIONS

Model

Major Features

Voltage DC 14.4 V/18 V

LED

Port USB A type

USB power supply

Operating time

(approximately)

(with BL1830, with the hook closed)

• Due to our ongoing research and development, the specifications herein are subject to change without notice.

• Note: Specifications may differ from country to country.

• Operating time may differ depending on battery type and usage condition.

Dimensions

Weight (without battery) 0.42 kg (0.9 lbs)

Output voltage DC 5 V Output current 2.1 A

Standard battery

cartridge

BL1415 2.0 hours 4.0 hours 6.0 hours

BL1415N 2.5 hours 5.0 hours 8.0 hours

BL1430 4.0 hours 8.5 hours 13 hours BL1440 6.5 hours 13 hours 21 hours BL1450 8.0 hours 16 hours 25 hours BL1815 2.5 hours 5.5 hours 8.5 hours

BL1815N 3.5 hours 6.5 hours 10 hours

BL1820, BL1820B 4.5 hours 9.0 hours 14 hours

BL1830 6.5 hours 12 hours 19 hours BL1840, BL1840B 9.0 hours 18 hours 28 hours BL1850, BL1850B 11 hours 23 hours 36 hours

BL1860B 14 hours 28 hours 43 hours

Main LED (20 pcs.)

when lit

L 361 mm (14-1/4”) x W 79 mm (3-1/8”) x H 121 mm (4-3/4”)

DML807

Main LED 0.5 W x 20 pcs.

Sub LED 2.0 W x 1 pc.

Main LED (10 pcs.)

when lit

Sub LED (1 pc.)

when lit

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

When using electric luminaires, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including the following:

READ ALL INSTRUCTIONS.

1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery.

2. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

3. Use a power source with the voltage specified on the nameplate of the charger.

4. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle.

5. Charge the battery cartridge with room temperature at 10°C - 40°C (50°F - 104°F). Let a hot battery cartridge cool down before charging it.

6. When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause sparks, burns, or a fire.

7. After charging or before attempting any maintenance or cleaning, unplug the charger from the power source.

8. Do not touch the inside of the flashlight head with tweezers, metal tools, etc.

9. Under abusive conditions, liquid may be ejected from the battery, avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

10. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive

material.

(2) Avoid storing battery cartridge in a container with

other metal objects such as nails, coins, etc. (3) Do not expose battery cartridge to water or rain. A battery short can cause a large current flow, overheating, possible burns and even a breakdown.

11. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.

12. Be careful not to drop or strike battery.

13. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.

Electrical safety

1. Do not insert a nail, wire, etc. into USB power supply port. Otherwise a circuit short may cause smoke and fire.

2. Do not connect power source to USB port. Otherwise there is risk of fire. The USB port is only intended for charging lower voltage device. Always place the cover onto the USB port when not charging the lower voltage device.

CAUTION:

1. When the luminaire is not in use, always switch off and remove the battery cartridge from the luminaire.

2. Do not store the luminaire and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F).

3. Do not give the luminaire a shock by dropping, striking, etc.

4. Do not expose the light to eyes continuously. It may hurt them.

5. Do not cover or clog the lit luminaire with cloth or carton, etc. Covering or clogging it may cause a flame.

6. Do not disassemble the charger or battery cartridge; take it to a qualified serviceman when service or repair is required. Incorrect reassembly may result in a risk of electric shock or fire.

7. Use the luminaires only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

8. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.

9. Do not use a damaged battery.

10. Charge the battery cartridge before completely discharged. Always stop luminaire operation and charge the battery cartridge when you notice less luminaire power.

11. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.

12. If any problem develops, consult your nearest Makita Service Center or dealer. To maintain product safety and reliability, repairs, maintenance or adjustment

should be carried out by Makita Authorized Service Center.

13. Charge the battery cartridge if you do not use it for a long period (more than six months).

For United States: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

SAVE THESE INSTRUCTIONS.

FUNCTIONAL DESCRIPTION

Installing or removing the battery cartridge (Fig. 1)

CAUTION:

• Always switch off the luminaire before installing or

removing of the battery cartridge.

• Hold the luminaire and the battery cartridge firmly

when installing or removing battery cartridge. Failure to hold the luminaire and the battery cartridge firmly may cause them to slip off your hands and result in damage to the luminaire and battery cartridge and a

personal injury. To remove the battery cartridge, slide it from the luminaire while sliding the button on the front of the cartridge. To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click. If you can see the red indicator on the upper side of the button, it is not locked completely.

CAUTION:

• Always install the battery cartridge fully until the red

indicator cannot be seen. If not, it may accidentally fall

out of the luminaire, causing injury to you or someone

around you.

• Do not install the battery cartridge forcibly. If the

cartridge does not slide in easily, it is not being inserted

correctly.

Switch operations (Fig. 2)

CAUTION:

• Do not look in the LED light or see the source of light

directly.

+ 8 hidden pages