Makita DHS630ZJ User manual
GB Cordless Circular Saw Instruction manual
F Scie Circulaire sans Fil Manuel d’instructions
D Akku-Handkreissäge Betriebsanleitung
I Sega circolare a batteria Istruzioni per l’uso
NL Accucirkelzaag Gebruiksaanwijzing
E Sierra Circular Inalámbrica Manual de instrucciones
P Serra Circular a Bateria Manual de instruções
DK Ledningsfri rundsav Brugsanvisning
GR Φορητό δισκοπρίονο Οδηγίες χρήσης
TR Akülü Sunta Kesme Kullanım kılavuzu
DHS630
012092
1 000186 2 000154
1
2
3
3 000156 4 000194
5 000147 6 000150
7 000029 8 012093
2
9 012128 10 012098
4
5
6
7
8
9
10
11
12
13
14
11 012100 12 012107
13 012105 14 012106
3
15 012094 16 012096
15
16
17
18
19
20
21
16
22
23
24
25
26
27
28
6
17 012097 18 012113
19 012149 20 012108
21 012109 22 012102
4
23 012103 24 012101
29
20
A
B
30
10
20
31
32
33
25 001145 26 012114
5
ENGLISH (Original instructions)
Explanation of general view
1. Red indicator
2. Button
3. Battery cartridge
4. Star marking
5. Lever
6. Wing screw
7. Cutting line
8. 45° position
9. 0° position
10. Screw
11. Top guide
12. Switch trigger
13. Lock-off lever
14. Light
15. Shaft lock
16. Hex wrench
17. Loosen
18. Hex bolt
19. Outer flange
20. Saw blade
21. Inner flange
22. Dust nozzle
23. Thumb screw
24. Hose
25. Vacuum cleaner
26. Clamp lever
27. Rip fence (Guide rule)
28. Adjusting screw
29. Triangular rule
30. Base
31. Limit mark
32. Brush holder cap
33. Screwdriver
SPECIFICATIONS
Model DHS630
Blade diameter 165 mm
Max. Cutting depth
No load speed (min
Overall length 346 mm
Net weight 3.5 kg
Rated voltage D.C. 18V
• Due to our continuing program of research and development, the specifications herein are subject to change without
notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for performing lengthways and
crossways straight cuts and mitre cuts with angles in
wood while in firm contact with the workpiece.
General Power Tool Safety
Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and
instructions for future reference.
CORDLESS CIRCULAR SAW
SAFETY WARNINGS
Cutting procedures
1. DANGER: Keep hands away from cutting area
and the blade. Keep your second hand on
auxiliary handle, or motor housing. If both hands
are holding the saw, they cannot be cut by the blade.
2. Do not reach underneath the workpiece. The guard
cannot protect you from the blade below the
workpiece.
6
at 90° 66 mm
at 45° 46 mm
-1
) 3,100
ENE028-1
GEA010-1
GEB061-4
3. Adjust the cutting depth to the thickness of the
workpiece. Less than a full tooth of the blade teeth
should be visible below the workpiece.
4. Never hold piece being cut in your hands or
across your leg. Secure the workpiece to a stable
platform. It is important to support the work properly
to minimize body exposure, blade binding, or loss of
control.
A typical illustration of proper hand support and
workpiece support. (Fig. 1)
5. Hold the power tool by insulated gripping surfaces
only, when performing an operation where the
cutting tool may contact hidden wiring. Contact
with a “live” wire will also make exposed metal parts of
the power tool “live” and could give the operator an
electric shock.
6. When ripping, always use a rip fence or straight
edge guide. This improves the accuracy of cut and
reduces the chance of blade binding.
7. Always use blades with correct size and shape
(diamond versus round) of arbour holes. Blades
that do not match the mounting hardware of the saw
will run eccentrically, causing loss of control.
8. Never use damaged or incorrect blade washers or
bolt. The blade washers and bolt were specially
designed for your saw, for optimum performance and
safety of operation.
Kickback causes and related warnings
- kickback is a sudden reaction to a pinched, bound or
misaligned saw blade, causing an uncontrolled saw to
lift up and out of the workpiece toward the operator;
Loading...