Magellan MAP410 User Manual

Map 410 GPS FAQs

1 Question:

Answer:

2 Question:

Answer:

3 Question:

Answer:

4 Question:

Answer:

How many batteries does my Map 410 GPS use?

Map 410 GPS uses four AA batteries.

How long will the batteries operate for my Map 410 GPS?

Using four AA batteries, your Map 410 GPS will operate
continuously for up to 12 hours.

How long will my Map 410 GPS keep memory active without a
battery?

The internal lithium backup battery will keep your receiver’s
memory active for up to 10 years.

How do I install the batteries in my Map 410 GPS?

The Map 410 GPS uses four AA alkaline batteries that are
installed from the bottom of the receiver. Use the rings to
unscrew the water seal battery caps. Insert the batteries into
the battery tubes, with the positive end first, two batteries in
each side, and screw the battery caps until securely closed.
Although it is recommended that four AA batteries be used, in
case of an emergency the receiver will operate with only two
batteries if both are inserted into one of the battery tubes.

5 Question:

Answer:

6 Question:

Answer:

7 Question:

Answer:

How do I turn on my Map 410 GPS?

To turn your Map 410 GPS “on”, press the power/light key and
then press the enter key when prompted. If the enter key is not
pressed within 10 seconds of being prompted, the receiver will
turn “off”. Wait for the unit to scroll through the start-up
screens.

How do I turn off my Map 410 GPS?

To turn your Map 410 GPS “off”, press and hold the same
power/light key. This will start a shutdown sequence that
counts down the seconds until the receiver actually turns
“off”. To immediately turn the receiver “off”, release and press
the power/light key again. To cancel the shutdown sequence,
press any other key.

How do I initialize my MAP 410 GPS for the first time use?

Turn your receiver on by pressing the power/ light key and the
enter key, when prompted. Because this is the first time you

have used your receiver, a screen will be displayed prompting
you to initialize your receiver. Press the enter key. When the
region screen appears, Use up/down arrow keys to highlight
the region where you are located. Enter mark. Use up/down
arrow keys to highlight country, province or state where you
are located. Enter mark. The elevation screen appears. Use the
arrow keys to enter your present elevation. Enter mark. From
the time field on the elevation screen. Use the arrow keys to
enter the local time and toggle between AM and PM. Enter
mark. From the date field on the elevation screen. Use the
arrow keys to input the date. Enter mark. During Initialization
at the Preference screen. Use the arrow keys to toggle
between marine and land. Enter mark. When you have chosen
the primary usage for your receiver, the status screen will be
displayed. At this point, you should go outside in an area
where you can get a clear view of the sky. Your Map 410 will
begin receiving data from the satellites in view and will display
the progress on the status screen. When your receiver has
computed a position fix, the map screen will be displayed. If
the map screen has been turned off then the position screen
will be displayed.

8 Question:

Answer:

9 Question:

Answer:

10 Question:

Answer:

11 Question:

Answer:

How do I save my position as a waypoint or landmark?

From any screen (press and hold) enter mark you will then see
a screen with you latitude/longitude readings and also a
default name LMK00X, press and hold the mark key again to
save.

How do I create a GOTO route to my saved waypoint or
landmark?

Press the GOTO key once then use up/down arrow keys to
highlight the user category and press enter mark. Use
up/down arrow keys to highlight the waypoint you just saved.
Enter mark.

How do I select the temp units in my Map 410 GPS?

From the Sat Status screen press menu. Use up/down arrow
keys to highlight temp units and press enter mark. Use
up/down arrow keys to select either Fahrenheit or Celsius

How do I set a temperature calibration?

From the sat status screen press menu. Use up/down arrow
keys to highlight temp calib and press enter mark. Use the
arrow keys to change the temperature. Enter mark. Use
up/down arrow keys to highlight save edits. Enter mark.

12 Question:

Answer:

How do I view the secondary coordinate system from the
position screen in my Map 410 GPS?
From the position screen, press the left/right arrows and the
lower half of the screen changes to display your present
position in the secondary coordinate system. The datums that
were selected under setup for each coordinate system are also
displayed.

13 Question:

Answer:

How do I customize the NAV screens in my Map 410 GPS?

From the NAV screen press men. Use up/down arrow keys to
highlight customize and press the enter Mark key. Use
up/down arrow keys to highlight the field you wish to change
and press enter. A pop-up menu appears> Use up/down arrow
keys to highlight your choice. Enter mark> You are returned to
the NAV1 screen in the customize mode> You can continue
customizing using the same steps or press quit to exit this
mode.

14 Question:

Answer:

15 Question:

Answer:

16 Question:

Answer:

17 Question:

How do I customize the compass screen in my Map 410 GPS?

From the compass screen. Press menu. Use up/down arrow
keys to highlight customize and press the enter mark key. Use
up/down arrow keys to highlight the field you wish to change.
Enter mark. A pop-up menu appears. Use up/down arrow keys
to highlight your choice and press the enter mark key. Then
You are returned to the compass screen in the customize
mod> You can continue customizing using the same steps or
press quit to exit this mode.

How do I enter the map setup screen in my Map 410 GPS?

From the map screen press menu. Use up/down arrow keys to
highlight map setup. Press the enter mark key to exit map
setup. Press the quit key.

What are all the options available in map screen orientation?

The map screen has three types of orientation to choose from:
North up, course up and track up. North up has north located
at the top of the screen; Course up has the destination of the
current leg at the top of the screen; track up has the direction
you are moving at the top of the screen.

How do I change the map screen orientation in my Map 410
GPS?

Answer:

18 Question:

Answer:

19 Question:

Answer:

From the map screen press menu. Use up/down arrow keys to
highlight map setup and press enter on the enter mark key.
Use up/down arrow keys to highlight the orientation setting.
Enter mark. Use up/down arrow keys to highlight your choice
and press enter mark.

How do I turn on/off the latitude/longitude grid in my Map 410
GPS?

From the map screen press menu. Use up/down arrow keys to
highlight map setup. Enter mark. Use up/down arrow keys to
highlight latitude/longitude grid. Enter mark. Use up/down
arrow keys to highlight on or off. Enter mark.

How do I enable/disable uploaded map data in my Map 410
GPS?

From the map screen press menu. Use up/down arrow keys to
highlight map setup press the enter mark key. Use up/down
arrow keys to highlight the uploaded data. Press the enter
mark key. Use up/down arrow keys to highlight on or off. Enter