Mac allister MBCP254 DUPLEX Operator's Manual
Brushcutter
MBCP254
OPERATOR’S MANUAL
WARNING: read thoroughly the instruction booklet
before using this machine
DUPLEX
ENGLISH -
EN
Original Instructions ....................................................................
ii
1
2
4
5
4
5
2
1
3
6
7
4
5 5
6
7
7
1
2
3
1
2
3
1
4
1
2
3
4
6
5
7
8
12
3
45
6
ii
1
2
3
4
STOP
START
RUN
STOP
START
RUN
CHOKE
RUN
1
1
2
2
3
3
4
4a
5
6
2.2
1
2.4
2.3
2.1
2
87
9
1101
4131 15
iv
0,5 mm
1
1
2
3
2
30°
A
B
C
30°
2
1
3
16 17
18 19
20 21
22
2
5
3
1
Ø 2,4 mm
2 x 3,0 m (118 in.)
4
6
120 mm
(4,75 in.)
7
iv
EN
INTRODUCTION
1
Dear Customer,
thank you for choosing one of our products. We hope that you will be completely satisfiedwith this machine
and that it fully meets your expectations. This manual has been compiled in order to provide you with all
the information you need to get acquainted with the machine and use it safely and efficiently. Don’t forget
that it is an integral part of the machine, so keep it handy so that it can be consulted when necessary, and
pass it on to a further user if you resell or loan the machine.
Your new machine has been designedand manufacturedin pursuance with current regulations, and is safe
and reliable if used in compliance with the instructions provided in this manual (proper use). Using the machine in any other way, or non-compliance with the safety specifications relative to use, maintenance and
repair is considered "improper use" which will invalidate the warranty, relieve the manufacturer from all liabilities, and the user will consequently be liable for all and any damage or injury to himself or others.
Since we regular improve our products, you may find slight differences between your machine and the descriptions contained in this manual. Modifications can be made to the machine without notice and without
the obligation to update the manual, although the essential safety and function characteristics will remain
unaltered. In case of any doubts, please contact your dealer. And now enjoy your work!
TABLE OF CONTENTS
1. Identification of the main components ....................................... 2
2. Symbols ..................................................................................... 3
3. Safety requirements ................................................................... 4
4. Machine assembly ..................................................................... 6
5. Preparing to work ....................................................................... 7
6. How to start - Use - Stop the engine .......................................... 8
7. Using the machine ................................................................... 10
8. Maintenance and storage ........................................................ 12
9. Troubleshooting ....................................................................... 14
10. Technical data ......................................................................... 14
11. Accessories ............................................................................. 16
EN
MAIN COMPONENTS
1. Power unit
2. Drive tube
3. Cutting device
a. Blade with 3 points
b. Cutting line head
4. Cutting device guard
5. Front handgrip
6. Guard
7. Handlebar
8. Rear handgrip
9. Connection point
(of the webbing)
10. Identification plate
11. Webbing
a. single belt
b. double belt
12. Angle transmission
13. Blade protection (for transport)
14. Spark plug
CONTROLS AND FILLING POINTS
21. Engine stop switch
22. Throttle trigger
23. Throttle trigger lockout
24. Starter
25. Choke
26. Primer
31. Fuel tank cap
2 IDENTIFICATION OF MAIN COMPONENTS
1. IDENTIFICATION OF MAIN COMPONENTS
1
“DUPLEX”
2
4
12
13
3a
7
9
10
11a
11b
3b
21
23
22
21
22
1
3
“MONO”
23
6 5
8
14
25
26
31
24
IDENTIFICATION PLATE
10.1) Conformity marking in accordance with Directive 2006/42/EC
10.2) Name and address of the manufacturer
10.3) Acoustic output level LWA in accordance
with directive 2000/14/EC
10.4) Machine model
10.5) Serial number
10.6) Year of manufacture
10.7) Article Code
10.8) Emission number
Petrol Brushcutter and Grass Trimmer
10.1 10.2 10.310.4
10.6 10.5 10.710.8
10.9) Displacement / Power / RPM
10.10) Cutting width
10.9
10.10
Loading...