Lucent Technologies PacketStar PSAX 20, PacketStar PSAX 2300, PacketStar PSAX 1250, PacketStar PSAX AC 60, PacketStar PSAX 4500 User Manual

PacketStar® PSAX

4-Port Voice 2-Wire Office Module User Guide

for the PacketStar® PSAX Multiservice Media Gateways

Issue 1, August 2001 System Software Release 7.0

AQueView

EMS Software Release 5.0

Doc. No.: 255-700-186

see the "Copyright and Legal Notices" section.

other countries. It may not be reproduced, distributed, or altered in any fashion by any entity (either internal or external to Lucent Technologies), except in accordance with applicable agreements, contracts or licensing, without the express written consent of the originating organization and the business management owner of the material.

This document was prepared by the Information Design and Development T ea m of Lucent Technologies, PacketStar in Landover, Maryland, USA.

Trademarks

7R/E, APX-8 000, CellPipe, ConnectReach, ConnectStar, and S TINGER are trademarks; and PacketStar, AQueView, Lucent Technologies, and the Lucent Technologies logo are registered trademarks of Lucent Technologies in the USA. Other product and brand names mentioned in this guide are trademarks or registered trademarks of their respective owners.

Warranty Information

Software and Hardware Limited Warranties

Lucent Technologies provides a 90-day limited software warranty, and a oneyear limited hardware warranty on this product. Refer to the Software License

and Limited Warranty Agreement and the Lucent Technologies InterNetworking Systems G lobal Warranty that accompanied your package for more

information.

PSAX Products. O ffi c e s ar e lo ca te d

Every effort has been made to ensure that this document is complete and accurate at the time of release, but information is subject to change. Lucent Technologies assumes no responsibility or liability for errors or inaccuracies that may appear in this guide.

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 255-700-186 iii

Regulatory Standards Compliance

Warr anty Warnings

Modifying or tampering with PSAX chassis components may void your warranty. Any modification to this equipment not expressly authorized by Lucent Technologies may void your granted authority to operate such equipment.

When inserting modules into the chassis, slide them gently, not forcefully. Excessive force may cause the modules to be seated improperly in the chassis, and result in possible damage to the module or the chassis. Install or remove modules one at a time. Doing this aids in preventing the Multiservice Media Gateway system from indicating any erroneous failure messages, and allows the Multiservice Media Gateway system to reinitialize and display the accurate configuration of the module that is inserted.

Shipping the chassis with removable modules installed may cause damage to the chassis and the modules. Damage to any of the components in the system resulting from shipping the chassis with removable modules installed could void your warranty. Only Lucentauthorized personnel should ship the Multiservice Media Gateway chassis with a module installed.

CAUTION:

Regulatory Standards Compliance

Safety and Electromagnetic Compatibility (EMC)

The 4-Port Voice 2-Wire Office module (model <Var. Model Number>) is compliant with applicable safety and EMC standards when configured with the following PacketStar

• PSAX 20 base system, 110 V ac (models 02S00 and 02S01)

• PSAX AC 60 base systems: ~ PSAX AC 60 system, 110 V ac (models 50S01 and 51S01)

~ PSAX AC 60 system, 220 V ac (models 50S02 and 51S02) ~ PSAX AC 60 system, -48 V dc (models 50S48 and 51S48)

• PSAX 1000 chassis (model 10S00)

• PSAX 1250 chassis (models 20S00 and 20S10)

• PSAX 2300 chassis (model 23S00)

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 iv 255-700-186

PSAX systems:

Regulatory Statements

• PSAX 4500 chassis (model 45S00) Please refer to the appropriate PacketStar

user guide or installation guide for additional information.

PSAX Multiservice Media Gateway

Telecommunications

• FCC Part 68 (USA)

• CS-03 Issue 8 (Canada)

Regulatory Statements

USA Regulatory State ments

FCC Part 68 This equipment complies with Part 68 of the FCC rules. On the back of the

PSAX chassis is a label that contains the FCC registration number, in addition to other information. You must provide this information to the telephone company, if they request it. The FCC requires Lucent Technologies to provide you with the following information:

1. This equipment has digital service interface capabilities using RJ-48C and RJ-48H connectors. The facility interface codes with which this equipment complies for digital services are as follows: 04DU9-BN, 04DU9-DN, 04DU9-1KN, and 04DU9-1SN. This equipment has loop start interface capabilities using an RJ-11C connector. The facility interface code with which this equipment complies for service is 02LS2. The service order codes for this equipment are 6.0F for the T-1 interface and 9.0Y for the loop start interface.

2. An FCC-compliant telephone network interface jack is built into this equipment and is compatible with interconnections that are Part 68 compliant.

3. The REN for the Voice 2-Wire Office module when used in this equipment is 0.7B.

4. If this equipment causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service might be required. But if advance notice is not practical, the telephone company will notify you as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe this is necessary.

5. The telephone company might make changes in its facilities, equipment, operations, or procedures that could affect the operation of this equipment. If this happens, the telephone company will provide advance notice for you to make necessary modifications to maintain uninterrupted service.

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 255-700-186 v

Regulatory Statements

6. If you experience trouble with this equipment, or need repairs or warranty information, please refer to the Lucent Techn o l o g i es InterNetworking Systems Global Warranty that accompanied your PSAX product shipment for instructions on obtaining technical support in your area.

If this equipment is causing harm to the telephone network, the telephone company might request that you disconnect the equipment until the problem is resolved.

7. This equipment has no user-serviceable parts.

This equipment cannot be used on public coin telephone service provided by the telephone company. Connection to party line service is subject to state tariffs. Contact your state public utility commission, public service commission, or corporation commission for information.

Canadian Regulatory Statements

CS-03 Issue 8 The Industry Canada label identifies certified equipment. This certification

means that the equipment meets certain telecommunications network protective, operational, and safety requirements. The Department does not guarantee that the equipment will operate to the user’s satisfaction.

Before installing this eq uip ment, t h e user s hou ld e nsu re that it i s perm iss ib le to be connected to the facilities of the local telecommunications company. The equipment must also be installed by using an acceptable method of connection. In some cases, the company’s inside wiring associated with a single-line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above condition may not prevent degradation of service in some situations.

Repairs to some certified equipment should be made by an authorized maintenance facility designated by the supplier. Any repairs or alterations made by the user to this equipment or equipment malfunctions might give the telecommunications company caus e to request the user to disconnect the equipment.

For their own protection, users should ensure that the ground connections of the power utility , telephone lines, and internal metallic water pipe system are connected together. This precaution may be particularly important in rural areas.

CAUTION:

Users should not attempt to make such connections themselves, but should contact the appropriate electric inspection authority or electrician.

The Ringer Equivalence Number (REN) assigned to the Voice 2-Wire Office module denotes the percentage of the total load to be connected to a telephone loop, which is used by the device, to prevent overloading. The

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 vi 255-700-186

Regulatory Statements

termination on a loop may consist of any combination of devices subject only to the requirement that the to tal of the REN of all devices does not exceed 5.

The REN for the Voice 2-Wire Office module when used in the PSAX system is 0.7B.

SH-03 Version 8 Le label Industrie Canada permet de reconnaître les équipements

homologués. Cette homologation indique que l’équipement satisfait certaines règles de protection, d’exploitation et de sécurité des réseaux de télécommunications. Le ministère de l’Industrie ne garantit pas que l’équipement fonctionnera à la satisfaction de l’utilisateur.

Avant d’installer cet équipement, l’utilisateur doit s’assurer qu’il est permis de le connecter aux installations de la compagnie de télécommunications locale. L’équipement doit également être connecté suivant une méthode convenable. Dans certains cas, il sera nécessaire de prolonger le câblage intérieur de la ligne d’abonné de la compagnie au moyen d’un connecteur homologué (rallonge de téléphone). L’abonné doit savoir que, dans certaines situations, la conformité aux dispositions ci-dessus ne prévient pas nécessairement la dégradation du service.

La réparation de certains équipements homologués doit être assurée par un atelier agréé désigné par le fournisseur. Toute réparation ou altération effectuée par l’utilisateur ou tout mauvais fonctionnement de cet équipement peut donner à la compagnie de téléphone des raisons de demander audit utilisateur de déconnecter celui-ci.

Pour leur propre sécurité, les utilisateurs doivent veiller à ce que les mises à la terre de l’alimentation secteur, des lignes téléphoniques et du système intérieur de conduites d’eau métalliques soient raccordés ensemble. Cette précaution peut s’avérer particulièrement importante dans les zones rurales.

CAUTION:

Les utilisateurs ne doivent pas tenter d’effectuer eux-mêmes ces raccordements, mais doivent prendre contact avec un électricien ou organisme de vérification compétent.

Le nombre équivalent de sonnerie (REN) attr ibué au module cen tral bifilaire (Voice 2-Wire Office) correspond au pourcentage de la charge totale à connecter à un circuit téléphonique bifilaire; il est utilisé par l’appareil pour prévenir la surcharge. Le circuit peut être terminé par n’importe quelle combinaison d’appareils, à la seule condition que le total des REN de ces derniers ne dépasse pas cinq.

Lorsqu’il est utilisé dans le système PSAX, le module central bifilaire possède un REN de 0,7 B.

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 255-700-186 vii

Regulatory Statements

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 viii 255-700-186

Safety Warnings and Information

When installing and operating the PacketStar® PSAX Multiservice Media Gateway, follow the safety guidelines provided below to help prevent serious personal injury and damage to the Multiservice Media Gateway equipment. Please read all warnings and instructions supplied before beginning installation or configuration of the Multiservice Media Gateway equipment. In addition to the general safety information provided below, you should also refer to the text in the user and installation guides for other important safety information and procedures.

DANGER:

Read all installation instructions before connecting the system to a power source.

DANGER:

Interface lines connected to the Voice 2-Wire Office module (model number 20N32) that exit the building premises must be connected to any nationally recognized testing laboratory (NRTL)-listed telecommunications protection device that provides primary and secondary protection. These protection devices provide overvoltage protection to the Voice 2-Wire Office module interface lines.

WARNING:

Be sure to use the ejector handles during installation and removal of I/O and server modules.

WARNING:

Electrostatic discharge (ESD) can damage module and chassis components. All personnel should be grounded and follow proper ESD procedures before installing, removing, or handling hardware components.

CAUTION:

Ultimate disposal of this product should be handled according to all laws and regulations in your specific geographic region.

CAUTION:

Do not make electrical or mechanical modifications to any of the components in the PSAX system. Lucent Technologies is not responsible for the safety or the performance of a modified Lucent product. Do not attempt to repair any failed Power Supply module, Stratum 3–4 module, CPU module, I/O, or server module.

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 255-700-186 ix

Safety Warnings and Information

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 x 255-700-186

Contents

Copyright. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Warranty Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Software and Hardware Limited Warranties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iii

Warranty Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Regulatory Standards Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Safety and Electromagnetic Compatibility (EMC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . iv

Telecommunications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Regulatory Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

USA Regulatory Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

FCC Part 68 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v

Canadian Regulatory Statements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

CS-03 Issue 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vi

SH-03 Version 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .vii

Safety Warnings and Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ix

1 Getting Started. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

Overview of This Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

Audience for This Guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

What You Should Know. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-1

Related Reading . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Lucent Technologies Information Products . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Product Information Library . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Printed Documents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Other Publications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

About Lucent Technologies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

History. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

For More Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

About the PacketStar PSAX Product Family. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-3

Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

Text Types Used in This Document . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-4

Icons and Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-5

Electrostatic Discharge Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-6

iii

.vii

1-1

.1-1 .1-1 .1-1 .1-2 .1-2 .1-2 .1-2 .1-2 .1-2 .1-2 .1-2 .1-3 .1-4 .1-4 .1-5 .1-6

iii iii iii iii iv iv iv

v v v

v vi vi

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 255-700-186 xi

Contents

Grounding Wrist Straps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Floor Covering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Temperature and Humidity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-6

Clothing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Handling Multiservice Media Gateway System Components . . . . . . . . . . . . . . . . . . . 1-7

Technical Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Comments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8

2 Module Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1

Overview of This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1

4-Port Voice 2-Wire Office Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Module Placement Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Hardware Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

General Hardware Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2

Chassis Speed, Power Consumption, and Memory Allocation . . . . . . . . . . . . . . . . . . . . . 2-3

LED Indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3

3 Configuring Ports and Channels Using the Console Interface . . . . . . . . . . . .3-1

Overview of This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Configuring the Module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

Saving the Equipment Configuration and Logging Off . . . . . . . . . . . . . . . . . . . . . . . . . . 3-9

1-6 1-6 1-6 1-7 1-7 1-7 1-7 1-8

2-1

2-1 2-2 2-2 2-2 2-2 2-3 2-3

3-1

3-1 3-1 3-1 3-9

4 Configuring Ports and Channels Using the AQueView® System . . . . . . . . . .4-1

Overview of This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Before You Begin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Using the Right-Click Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1

Configuring Ports and Channels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

Context-Sensitive Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Configuring the Voice 2-Wire Office Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

Configuring the Module. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-4

Copying a Port Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9

Channel Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

Buttons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11

5 Configuring the Interfaces Using the Console Interface. . . . . . . . . . . . . . . . .5-1

Overview of This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Circuit Emulation Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1

Taking the Interface Out of Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 xii 255-700-186

4-1

4-1 4-1 4-1 4-2 4-3 4-3 4-4

4-9 4-10 4-11

5-1

5-5

Contents

Deleting the Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5-5

6 Configuring Interfaces Using the AQueView® System. . . . . . . . . . . . . . . . . 6-1

Chapter Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

Errors Applying Interfaces to Ports . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

The Circuit Emulation Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-1

Copying an Interface Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6-6

7 Provisioning Connections Using the Console Interface. . . . . . . . . . . . . . . . . 7-1

Overview of This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1

Data Flow in PVCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-1

Provisioning PVC Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-2

Adding a Circuit Emulation-to-ATM VCC PVC Connection . . . . . . . . . . . . . . . . . . . . . . . .7-3

Creating a Circuit Emulation-to-ATM VCC Connection. . . . . . . . . . . . . . . . . . . . .7-4

Connection Capacity of DSP2x Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-5

Connection Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-11

Backup Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-14

Adding a Circuit Emulation-to-Circuit Emulation PVC Connection. . . . . . . . . . . . . . . . . .7-17

Creating a Circuit Emulation-to-Circuit Emulation Connection . . . . . . . . . . . . . .7-17

Connection Capacity of DSP2x Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-19

Viewing Connection Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-22

Provisioning SPVC Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-24

Creating a Circuit Emulation-to-ATM Connection. . . . . . . . . . . . . . . . . . . . . . . .7-24

Connection Capacity of DSP2x Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-26

Configuring Digital Signal Processing (DSP2) Parameters . . . . . . . . . . . . . . . . . .7-30

Viewing Connection Statistics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-32

.5-5

6-1

.6-1 .6-1 .6-1 .6-6

7-1

.7-1 .7-1 .7-2 .7-3 .7-4

.7-5 .7-11 .7-14 .7-17 .7-17 .7-19 .7-22 .7-24 .7-24 .7-26 .7-30 .7-32

8 Provisioning Connections Using the AQueView® System. . . . . . . . . . . . . . . 8-1

Overview of This Chapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1

Data Flow in PVCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-1

Managing Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-2

Searching for Specific Connection Entries. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-3

Viewing Connection Details. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-5

Displaying and Updating Connection Information . . . . . . . . . . . . . . . . . . . . . . . .8-5

Display Connection Tabs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-6

Copying a Connection Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-6

Filtering Connections in the List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-9

Filtering the Listing Page by Connection Type. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-9

Filtering the Listing Page by PSAX Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-11

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 255-700-186 xiii

8-1

.8-1

.8-2

.8-3

.8-5

.8-6

.8-9

.8-9 .8-11

Contents

SPVC NSAP Addresses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-12

AAL2 Trunk Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-13

Configuring AAL2 Trunking with DSP Processing . . . . . . . . . . . . . . . . . . . . . . . . . . .8-13

Creating Connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-13

Using the Right-Click Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-14

Connection Provisioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-14

Context-Sensitive Help. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-15

Adding Circuit Emulation to ATM PVC Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-16

Adding Circuit Emulation-to-ATM VCC PVC Connections. . . . . . . . . . . . . . . . . . . . .8-16

Creating a Circuit Emulation-to-ATM VCC Connection. . . . . . . . . . . . . . . . . . . .8-16

Primary Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-22

Statistics Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-23

Backup Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-26

Utilization Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-29

Adding Circuit Emulation-to-Circuit Emulation PVC Connections . . . . . . . . . . . . . . .8-32

Creating a Circuit Emulation-to-Circuit Emulation VCC Connection . . . . . . . . . .8-32

Primary Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-36

Statistics Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-37

Utilization Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-39

Provisioning SPVC Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-42

Creating a Circuit Emulation-to-ATM Connection. . . . . . . . . . . . . . . . . . . . . . . .8-42

Primary Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-49

Statistics Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-51

Utilization Page . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8-53

.8-12 .8-13 .8-13 .8-13 .8-14 .8-14 .8-15 .8-16 .8-16 .8-16 .8-22 .8-23 .8-26 .8-29 .8-32 .8-32 .8-36 .8-37 .8-39 .8-42 .8-42 .8-49 .8-51 .8-53

Appendix A: Reference Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Overview of This Appendix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

Call Tone Detection Settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1

DSP Channel Reduction Availability Due to Fax Relay Mode . . . . . . . . . . . . . . . . . . . . . . A-2

Industry Compliance Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2

Interface Type by Connection Type Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-23

Interface Type by Input/Output Module Type Table . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-24

Module Alarm Status Table. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-28

Quality of Service (QOS) Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-29

A-1

A-1 A-2 A-2

A-23 A-24 A-28 A-29

Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Glossary-1

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 255-700-186 xiv

Ove rview of This Guide

The PacketStar® 4-Port Voice2-Wire Office Module User Guide provides information about the following:

• Configuring the ports, channels, and interfaces for the 4-Port Voice 2Wire Office module

• Provisioning connections for permanent virtual circuits (PVCs), switched virtual circuits (SVCs), and soft permanent virtual circuits (SPVCs)

Note: If you are using this module to provision connections for the first

time, you should read through this guide before beginning the provisioning process.

Audience for This Guide

1 Getting Started

The information in this guide is intended for users who will configure ports and channels for the 4-Port Voice 2-Wire Office module, configure the interface types, and provision connections for the PSAX Multiservice Media Gateway system, whether using the console or the AQueView management software system.

What You Should Know

Before you use this document or operate a PacketStar® PSAX device, you should already understand and have experience with the following:

• ATM Forum and Frame Relay Forum specifications

• Ethernet network capabilities

• Internet Protocol capabilities

• Data network design

• Telephony network design

element

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 255-700-186 1-1

Chapter 1 Getting Started

Related Reading

Lucent Technologies Information Products

Product Information Library

Printed Documents For your convenience, many of the documents included on the PacketStar

Other Publications Numerous books are currently available on the subject of basic

To install and configure your Multiservice Media Gateway system and I/O or server modules, read the PSAX publications provided on your Lucent Technologies PacketStar PSAX Multiservice Media Gateways Central Office (CO) Products, Product Information Library CD-ROM.

Multiservice Media Gateway Central Office (CO) Products Product Information Library CD-ROM are also available in printed form. You can order these documents through the Lucent Technologies Customer Information Center Web site at: www.lucentdocs.com.

telecommunications technology and specific protocols. In addition to such general reading, you should also be familiar with the specifications identified in the appendix entitled Reference Tables at the back of the guide.

About Lucent Technologies

History

Lucent Technologies is the communications systems and technology company formed through the restructuring of AT&T. We bring with us a tradition of more than 125 years of experience and a dedication to superior customer service.

Lucent Technologies manufactures, sells, and services a complete line of customer premises communications units, and commercial and multimedia communications and messaging systems designed and supported by our research and development unit, Bell Laboratories.

Our legacy and our spirit of innovation allow Lucent to provide our customers with the tools needed to communicate effectively, any time and anywhere, and to integrate the latest technologies into real-life solutions that help make business work.

For More Information

T o learn more about the PacketStar® PSAX family of ATM Multiserv ic e Med ia Gateways and the complete line of Lucent Technologies products, visit our Web site at www.lucent.com.

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 1-2 255-700-186

About the PacketStar PSAX Product Family

Chapter 1 Getting Started

Lucent Technologies provides a complete range of PSAX Multiservice Media

Gateways in the PacketStar

Table 1-1. PacketStar® PSAX Product Family

Target Market Device Name Application/Description

Small Customer Premises

PSAX 20

The PacketStar scalable and flexible multiservice access product in its class. This scalability enables service providers to meet the demands of a growing

PSAX family, as described in Table 1-1.

PSAX 20 Multiservice Media Gateway is the most

enterprise customer with a single-edge solution. The PSAX 20 system is nonredundant.

Supporting two slots for I/O and server modules and two factoryinstalled components (Enhanced DS1 and DSP2C V oice Server) and a 600 Mbps ATM cell bus architecture, this system optimizes wide area network (WAN) bandwidth with toll-quality voice compression, traffic optimization, and port scalability from T1/E1 to OC-3c/STM-1c connections. It also supports a full range of interfaces such as DS1, DS3, 10/100Base-T Ethernet, and serial.

Small Customer Premises

PSAX AC 60

The PacketStar enterprise networks se eki ng to consolid ate bra nch offi ce voice, vi deo , and data traffic onto a single ATM network. The PSAX AC 60 system

PSAX AC 60 Multiservice Media Gateway is ideal for

is nonredundant. Supporting four slots for I/O and server modules, this system offers

high port-density in a small footprint for mid- to large-sized customer premises applications. The PSAX AC 60 chassis has a 650 Mbps backplane and supports a full range of interfaces such as DS1/E1, DS3/E3, OC-12c/STM-4c, 10/100Base-T Ethernet, and serial.

Carrier-Class Office

PSAX 1250

The PacketStar to provide a full range of central office-based multiservice ATM access

PSAX 1250 Multiservice Media Gateway is designed

functions. Ideal for the central office or a large enterprise’s multiservice media gateway, the PacketStar

PSAX 1250 system provides highly reliable network access for time-division multiplex voice, frame relay, and ATM data applications.

Supporting ten slots (19-inch chassis) or 14 slots (23-inch chassis) for I/O and server modules, a 1.2 Gbps ATM cell bus architecture, carrierclass reliability, full redundancy, and a full range of interfaces such as DS1/E1, DS3/E3, OC-12c/STM-4c, 10/100Base-T Ethernet, and serial, the PSA X 1250 system is a cost-effect ive access switch solution for bridging to legacy equipment.

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 255-700-186 1-3

Chapter 1 Getting Started

Document Conventions

Table 1-1. PacketStar® PSAX Product Family

Target Market Device Name Application/Description

Carrier-Class Office

PSAX 2300

The PacketStar rier-grade, high-density multiservice ATM access functions. Designed

PSAX 2300 Multiservice Media Gateway offers car-

as the multiservice media gateway for the central office or for a large

enterprise customer, the PacketStar

PSAX 2300 system provides network access for time-division multiplex voice, frame relay, and ATM data applications.

Supporting 15 slots for I/O and server modules, a 3.9 Gbps ATM cell bus architecture, carrier-class reliability, full redundancy, provisions for OC-12c/STM-4c interfaces, N x T1/E1 module protection switching, and a full range of interfaces such as DS1/E1, DS3/E3, 10/100Base-T Ethernet, and serial the PSAX 2300 system solves many demanding and diverse network design challenges with ease.

Carrier-Class Office

PSAX 4500

The PacketStar 10 Gbps of switching capacity, the highest in the PacketStar

PSAX 4500 Multiservice Media Gateway offers up to

and carrier-class reliability. The PSAX 4500 system offers an unmatched range of service capabilities, end-to-end traffic prioritization, “any-service, any-channel” flexibility, and breakthrough voice technology. The new high-performance backplane design supports 15 interface slo ts.

In four segments, the uni qu e PSAX 4500 backplane allows each segment to be scaled independently to provide nonblocking, redundant chassis bandwidths beyond 10 Gbps. Protection for two groups of four multiport DS3, STS-1e, and E3 modules is provided via an N:1 protection scheme using rear access line interface modules. The protection module can fill in so that on the failure of any one of the four modules, traffic is maintained.

Using the latest voice-compression technology, the DSP2x Vo ice Server modules deliver service providers eight times the capacity of traditional time division multiplex circuits while maintaining toll quality and reducing costs by nearly 30 percent per channel. A single PSAX 4500 system at the edge of the carrier network can transition traffic from a large number of network customers over high-speed OC-12c/STM-4c trunks into the ATM core, managing the whole quickly and efficiently, down to the individual permanent virtual circuit.

family,

Document Conventions

Text Types Used in This Document

This book uses a different kind of type for each kind of text you will see on screens and equipment. In general, text you see in the book will closely

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 1-4 255-700-186

Chapter 1 Getting Started

Document Conventions

resemble what you see on the screens and equipment. The following table shows how each typographical convention is used.

Appearance How it is used

SANS SERIF BOLD, ALL CAPS Labels on module panels, chassis face-

plates, or other hardware

Fixed-width normal Message text displayed on the user

interface window

Serif bold • Button name (GUI interface) or

command name (console interface) on the user interface window

• Literal text for values that the user types in fields or selects from predefined sets of values for fields

• Command keywords or literal argument values

Icons and Symbols

Fixed-width bold System prompt displayed on the user

interface window

Serif italics • A variable name or string for which

you will substitute your own information

• An argument or parameter on a command line for which you will substitute your own information

Standard icons and symbols to alert you to dangers and cautions are listed below.

DANGER:

Warnings for a personal injury hazard are identified by this format.

WARNING:

Warnings relating to risk of equipment damage or failure are identified by this format.

CAUTION:

Warnings relating to risk of data loss or other general precautionary notes are identified by this format.

Note: Identifies additional information pertinent to the text preceding

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 255-700-186 1-5

this note.

Chapter 1 Getting Started

Electrostatic Discharge Precautions

The room where the Multiservice Media Gateway system is located must have built-in precautions to provide protection from electrostatic discharge damage to electronic components. The following sections provide details on these necessary precautions.

Grounding Wrist Straps

Attach at least one grounding wrist strap to a common ground for each chassis/electronic rack to be handled. Follow these guidelines for wrist straps:

• Make sure the wrist straps or wrist strap cords have built-in 1-megaohm (minimum) resistance.

• Make sure the wrist straps and wrist strap cords are UL listed.

• Ensure the wrist strap cord is long enough so it can be worn while

working either at the front or the back of the rack.

• Always discharge any static charge by touching your wrist strap before you touch the Multiservice Media Gateway chassis.

Floor Covering

Be sure the room has an antistatic floor covering (conductive mat, tiles, or carpeting) to minimize static charge buildup as you walk across the room. Follow these guidelines for installing and maintaining proper floor coverings:

• Using foot grounding straps (attached to the heels of your shoes) is recommended, even if you are walking in rooms with antistatic floor covering. These straps provide additional protection against electrostatic discharge. The straps should have built-in 1-megaohm (minimum) resistance.

• Wool carpet is not an acceptable floor covering.

• Other types of carpet must be sprayed daily with a topical antistatic

chemical before you perform any work in the room. Paying constant attention to carpet maintenance is time-consuming but required, if used.

Temperature and Humidity

Establishing the proper temperature and humidity in the room where the Multiservice Media Gateway system is located helps control many static discharge problems. Maintaining proper room climate is especially important when heat is turned on during the cold weather. To avoid damage to the Multiservice Media Gateway system, do not allow the humidity to increase to the level where water droplets appear on surfaces.

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 1-6 255-700-186

Chapter 1 Getting Started

Clothing

When working with the Multiservice Media Gateway system, avoid wearing clothing made from wool or synthetic materials. Try to minimize contact between clothing and electronic components.

Handling Multiservice Media Gateway System Components

Follow these guidelines for proper handling of the Multiservice Media Gateway hardware to minimize electrostatic discharge damage:

• Do not remove the chassis, modules, and other items from their protective packaging until you are ready to install them.

• When installing modules and components, use a grounding wrist strap connected to a common electrical ground to prevent electrostatic discharge damage. (A common electrical ground is a complete circuit between a person or an electrical/electronic device and the earth.)

• Store components in electrostatic-discharge-protective bags when they are not in use.

Technical Support

If you experience a problem with your Multiservice Media Gateway system, refer to the Lucent Technologies InterNetworking Systems Global Warranty, which accompanied your shipment, for instructions on obtaining support in your area.

Comments

To comment on the PacketStar® 4-Port Voice2-Wire Office Module User Guide, please complete the comment card that accompanied your shipment and mail it to the following address:

Manager, Information Design and Development Team Lucent Technologies PacketStar PSAX Products 8301 Professional Place Landover, MD 20785 USA

You can also fax the comment card to us at: 301-809-4540.

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 255-700-186 1-7

Chapter 1 Getting Started

Before You Begin

Before you start setting up, configuring, and using your new Multiservice Media Gateway system, be sure you complete the following:

• Carefully read the safety cautions listed in the section, “Safety

• Record your site-specific specifications such as the IP addresses you will

• Make sure you have IP connectivity to all PSAX devices to be managed.

• Determine the numbering scheme for the in-band connections you will

Information,” at the beginning of this guide.

use, and the connections and interfaces you will need. Decide which user names and passwords you will assign.

be using.

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 1-8 255-700-186

Overview of This Chapter

The Voice 4-Port 2-Wire Office module provides support for the office (central office or PABX switch) end of a two-wire analog telephone line. This allows a voice loop from a voice switch to be connected directly to a Multiservice Media Gateway system and communicate over an ATM network to a distant telephone or other analog device.

The 4-Port Voice 2-W ire Office module has three types of LED indicators: ACTIVE, FAIL, and LOS (loss of signal). Each port has a LOS LED on the faceplate. The LED turns on when the port goes off-hook. It also turns on and off in synchonization with an incoming ringing signal to the port.

2 Module Description

FAIL

ACTIVE

Figure 2-1. 4-Port Voice 2-Wire Office Module

VOICE

2WO

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 255-700-186 2-1

Chapter 2 Module Description

4-Port Voice 2-Wire Office Module

This module is typically configured with an 8-Port Voice 2-Wire Station module via a PVC connection to enable a foreign exchange (FXO) voice service to be transmitted across an ATM network. With FXO service, the voice switch provides dial tone, ringing, and digit translation, which are not provided by the ATM network.

Module Placement Requirements

Note: Do no place the 4-Port Voice 2-Wire Office module module in the

PSAX 4500 chassis; the module is not supported.

In all other PSAX chassis, you may install the module in any slot intended to contain I/O or server modules. In typical applications, this module is used with the 8-Port 2-Wire Station module, (see the appropriate module guide).

Hardware Features

The 4-Port Voice 2-Wire Office module supports these hardware features:

• Number of ports: 4

• Connector type: RJ-11

• Ringing frequency: 20 Hz

• Termination impedance: 600 Ohms

• Signaling: dual tone multi-frequency (DTMF)

• Supervision: loop start

General Hardware Specifications

Table 2-1 shows the general physical and environmental hardware specifications for the PSAX Multiservice Media Gateway I/O and server modules.

Table 2-1. Physical Hardware Specifications for the I/O and the Server Modules

Specification Description

Dimensions:

• Height:

•Width:

• Depth: Weight: 0.45 kg (1.0 lb.)

15.74 cm (6.2 in.)

2.41 cm (0.95 in.)

24.13 cm (9.5 in.)

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 2-2 255-700-186

Chapter 2 Module Description

Chassis Speed, Power Consumption, and Memory Allocation

Table 2-1. Physical Hardware Specifications for the I/O and the Server Modules

Specification Description

Operating temperature: 0° to 50° C (32° to 122° F) Operating relative humidity: 40 to 60%, optimum;

up to 95%, noncondensing

Storage temperature: -20° to 70° C (-4° to 158° F)

Chassis Speed, Power Consumption, and Memory Allocation

Chassis speed, power consumption, and memory allocation specifications for the 4-Port Voice 2-Wire Office module are described in Table 2-2.

Table 2-2. Chassis Speed, Power Consumption, and Memory Allocation Specifications

Maximum

Input

Buffer

Output

Buffer

Chassis

Speed

Module

4-Port Voice 2-Wire

Total

Amount of

SDRAM

8MB 4MB N/A N/A Low

Module

Program and

Data Space

Office (VOICE 2WO)

The I/O buffers carry 16,384 cells per megabyte for all Multiservice Media Gateway modules except the Voice 2-Wire

Office module, the Voice 2-Wire Station module, and the DSP2x Voice Server modules, which have no cells carried on the I/O buffers.

This column relates only to the performance of the module in the PSAX 4500 chassis. All modules operate in a low-

speed mode in all other PSAX chassis. The speed rel ates to the performance of the data being passed through the midplane of the chassis.

LED Indicators

Table 2-3 describes how the light-emitting diode (LED) indicators on the 4Port Voice 2-Wire Office module faceplates respond to different module conditions. These LEDs indicate if the module has been installed properly. Before you configure the 4-Port Voice 2-Wire Office module, you must ensure that it is properly initialized according to the information provided in Table 2-3.

Power Con-

sumption

14 W

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 255-700-186 2-3

Chapter 2 Module Description

LED Indicators

Table 2-3. LED Indicators for the 4-Port Voice 2-Wire Office Module

Module

Status

LED

FAIL (red)

ACTIVE (green)

Line Status LOS

(green)

Note: After power is initially applied to the system and the system boot is complete, the FAIL and ACTIVE LEDs indicate whether the module has no configured ports (red), or one or more configured ports (green).

Note: This module does not have this label next to the LED indicator on the faceplate.

Power-On

Lights briefly

Each lights

briefly

Initial

Configured

Ports

One or More

Configured

Ports

Not lit Lights only

when the module is not functioning

Not lit Lights only

when the module is functioning properly

Not Applicable

No Cable on

Port

Not Applicable

Cable on

Port

Not Applicable

Not lighted Flashing

green LED indicates the line is ringing.

Solid green LED indicates the line is offhook (in use) or busy.

Unilluminated LED indicates the line is on-hook (not in use).

Note: Shielded RJ-11 to RJ-11, straight through cables are needed with

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 2-4 255-700-186

the 4-Port Voice 2-Wire Office module.

3 Configuring Ports and Channels

Using the Console Interface

Overview of This Chapter

This chapter describes how to set the values for the port and channel configuration for the 4-Port Voice 2-Wire Office module using the PSAX Multiservice Media Gateway system console interface.

Before You Begin

Be sure to complete the following actions first before configuring the 4-Port Voice 2-Wire Office module:

• Configure your basic system (see "Configuring the System for Your Site" in Chapter 4 of the appropriate PacketStar Gateway user guide)

PSAX Multiservice Media

• Configure the Stratum 3–4 mod ule (see "Configuring the Stratum 3–4 Module" in Chapter 4 of the appropriate PacketStar Media Gateway user guide)

When configuring the 4-Port Voice 2-Wire Office module using the PSAX Multiservice Media Gateway console, display-only fields are displayed with brackets.

The status line at the bottom of the console window gives instructions for the field currently selected, and displays trap messages (see the appendix of your chassis user guide for a table of defined trap messages).

CAUTION:

When using a DSP2A, DSP2B, DSP2C, or DSP2D Voice Server module and an Enhanced DS1 or E1 module with a PBX and/or key telephone system, the Multiservice Media Gateway system and your equipment should use a common chassis ground connection to avoid ground current loops, which could affect voice quality.

Configuring the Module

T o configure the 4-Port V oice 2-Wire Office module ports, follow the steps in the following procedure.

PSAX Multiservice

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 255-700-186 3-1

Chapter 3 Configuring Ports and Channels Using the Console Interface

Configuring the Module

Configuring the Ports

Begin

1 On the Console Interface Main Menu window (see Figure 3-1), select

the Equipment Configuration option and press Enter.

Figure 3-1. Console Interface Main Menu (Equipment Configuration Selected)

The Equipment Configuration window (see Figure 3-2 and Figure 3-3) is displayed.

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 3-2 255-700-186

Chapter 3 Configuring Ports and Channels Using the Console Interface

Configuring the Module

Figure 3-2. Equipment Configuration Windo w (As Displayed o n the PSAX 20

and AC 60 Console)

Figure 3-3. Equipment Configuration Window (As Displa yed on the PSAX 1250,

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 255-700-186 3-3

PSAX 2300, and PSAX 4500 Console)

Chapter 3 Configuring Ports and Channels Using the Console Interface

Configuring the Module

2 On the Equipment Configuration window, select the 4-Port Voice 2-

Wire Office module and press Enter. The Two Wire Office Configuration window is displayed (see

Figure 3-4).

Figure 3-4. Two Wire Office Configuration Window

Commands The commands in this window have the following functions:

Command Function

• Update Display Updates the values in the fields to show the most current configuration.

Use this command mostly to display the most current information in the Line Status field.

• Configure All Interfaces Sets all four ports to the circuit emulation type interface. The value CircuitEmulation is displayed in the Interface Type field, and the value OutOfService is displayed in the Oper Status field.

• Delete All Interfaces Deletes the configured interfaces for all four ports. The value Unconf igured is displayed in the Interface Type and the Oper Status fields.

Note: You must first take all interfaces out of service (using the Take All Interfaces Out Of Service command) before you can use this command to delete all the configured interfaces.

PacketStar® 4-Port Voice 2-Wire Office Module User Guide, Issue1 Release7.0 3-4 255-700-186

+ 238 hidden pages

Lucent Technologies PacketStar PSAX 20, PacketStar PSAX 2300, PacketStar PSAX 1250, PacketStar PSAX AC 60, PacketStar PSAX 4500 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual