Lucent Technologies Voice Terminal 8410, DEFINITY ECS Quick Reference

DEFINITY® Enterprise Communications Server (ECS) Release 5
8410 V oice Terminal Quick Reference
555-230-764 Comcode 107672974
Refer to the procedures on this card to use the features on your 8410 voice terminal. The features here are listed in alphabetical order. In the spaces provided, write the feature access codes for your system. For more information about any of these features, see your system manager or refer to the
DEFINITY ® Enterprise Server (ECS), Release 5
8410 Voice Terminal User’s Guide
, 555-230-763.
USING THE SOFTKEYS
If your 8410 has a display, you may be able to access up to 12 features with the softkeys. You can activate available softkey features by pressing and then
Menu
the softkey below the feature abbreviation. If the feature you wa nt to use is not on t he b ottom l ine of t he display, press or until you see the
Next Prev
feature you wish to access. When the feature is active, an arrow appears above the feature. (However, if the feature requires you to dial a telephone number or extension, such as Call Forwarding, you will temporarily see the digits you are dialing, rather than the arrow, above the feature name.)
ABBREVIATED DIALING (AD)
To program/reprogram an AD button 1 Pick up handset.
NOTE: For speakerphone users, press a call
appearance button or press .
2 Press softkey below Prog (for display users)
or Press or Dial AD Program access code _________.
3 Press AD button to be programmed.
Speaker
Program
1
4 Dial outside number, extension, or feature access
Pers List
code you want to store (up to 24 digits).
5 Press . 6 Repeat Steps 3 through 5 to program additional
buttons.
7 Hang up. To place an AD call
1 Pick up handset or press . 2 Press selected AD but ton.
To program/reprogram an outside number, extension, or feature access code into a personal list
1 Pick up handset.
NOTE: For speakerphone users, press a call
appearance button.
2 Press softkey below Prog (for display users)
or Press or Dial AD Program access code ________.
#
Speaker
Program
3 Dial Personal List number (1, 2, or 3). 4 Dial list item (1, 2, 3...). 5 Dial number you want to store (up to 24 digits). 6 Press . 7 Repeat Steps 4 through 6 to program additional
items on the same list.
8 Hang up. To place a call using an AD list button or access
code 1 Press or or
or Dial appropriate AD List access code:
#
Grp List
Sys List
List 1 __________
List 2 __________
List 3 __________
NOTE: An may also be available.
Enhcd List
2 Dial desired list item (1, 2, 3...).
2
Transfer
Consult
AUTOMATIC CALLBACK
AUTOMATIC CALLBACK
AAUTOMATIUTOMATIC CALLBACK
T o automatica lly place another call to an extension that was busy or did not answer
1 During call attempt, press softkey below AutCB
(for display users)
or Press .
AutoCallBk
2 Hang up.
You hear a 3-burst priority ring when both you
and the called extension are idle. Pick up handset to be connected to call.
To cancel Automatic Callback 1 While on-hook, press softkey below AutCB again
(for display users)
or Press again.
CALL COVERAGE/CONSULT
T o ans wer a cal l for a c oworker for whom you are a coverage point
AutoCallBk
1 Press the call appearance of incoming call when
ring begins or green light flashes.
To talk privately with a coworker after answering a redirected call
1 Press .
Call is put on hold.
2 Press
or Dial coworker’s extension. 3 Discuss call, if appropriate. 4 If coworker is no t available, press the call
appearance button next to the fluttering light to
reconnect to the call
or Press again to send call to coworker
or Press to make it a 3-party call.
Transfer Conf
3
Loading...
+ 7 hidden pages