NREZ022C
3-2017
CAL. Z022, Z024 (R23 SERIES)
FEATURES AND SPECIFICATION
■
1. This watch is a combination quartz watch with
analogue and digital displays, 3 hands analogue
movement.
2. Accuracy at normal temperature: ± 30 seconds
a month
3. Time keeping mode: hours, minutes, seconds,
month, date, day of week, “PM”(only available
in 12-hour format)
Press S1 button to show the month and date
indication.
4. Alarm Mode: Daily alarm.
5. Timer Mode:
Measuring unit: 1 second
Input range: from 1 second to 23:59’59”.
6. Stop watch Mode:
Measuring unit: 1/100 of second
Measuring capacity: 23:59’59”.
7. Normal operating temperature range: between
-20°C and 70°C.
8. Battery type: (For Cal. Z022) CR2016, SR626SW
(For Cal. Z024) CR2032, SR626SW
DIGITAL DISPLAY A
S4
(LIGHT)
DATE
DAY OF WEEK
SECONDS
S1
(START/STOP)
T I M E R
SIGNAL
CROWN
4. Press S1 button to adjust the value. Holding S1
button down can fasten the process.
5. When the 12-hour format is selected, the indicator
“PM” indicates “p.m.” times. There is no indicator
for “a.m.” times.
6. Press S2 button to confirm the settings.
S2
NORMAL TIME
S2
12/24 FORMAT SETTING
BY PRESSING S1
S3
SECOND SETTING BY
PRESSING S1
S3
HOUR SETTING BY
PRESSING S1
S3
S3
(MODE)
AFTERNOON
CHIME SIGNAL
DIGITAL DISPLAY B
DAY OF WEEK
S4
(LIGHT)
C H I M E
SIGNAL
A L A RM
SIGNAL
(MODE)
AFTERNOON
SETTING THE TIME (ANALOGUE)
■
HOUR HAND
SECOND HAND
1. Pull the crown out one step, the second hand
will stop.
2. Set the hands to the correct time by turning the
crown.
3. Push the crown back to the original position. The
watch will start running again.
The analogue indication and digital display of the
time setting can be adjusted separately.
HOW TO CHANGE DISPLAY MODE
■
Press S3 button to change the display mode. Each
time the button is pressed, the mode changes in
the following order.
NORMAL TIME CHRONOGRAPH
S3
HOURS
HOURS
ALARM SIGNAL
DATE
MINUTES
S3
S2
(SET/RESET)
CHRONOGRAPH
SIGNAL
MINUTES
SECONDS
S1
(START/STOP)
CROWN
T I M E R
SIGNAL
S2
(SET/RESET)
CHRONOGRAPH
SIGNAL
MINUTE HAND
CROWN
DAY OF WEEK SETTING
BY PRESSING S1
S3
DATE SETTING BY
PRESSING S1
HOW TO USE STOPWATCH
■
From the normal time mode, press S3 button once,
you are now in the chronograph mode.
MINUTE SETTING BY
PRESSING S1
S3
S3
MONTH SETTING BY
PRESSING S1
First Usage:
1. Press S1 button alternately to start and stop the
chronograph.
2. Press S2 button to reset the chronograph to zero.
3. Press S3 button to return to normal time
mode. (This can be done at any time with the
chronograph still running.)
Second Usage:
1. Press S1 button to start counting.
2. Press S2 button to show the first split time T1 (0
to T1). The digits stop flashing, but chronograph
is still counting.
3. Press S2 button again to continue counting.
4. Further press S2 button to show the second split
time T2 (0 TO T2). This operation can be repeated
and the split times can be read: 0 to T3, 0 to T4
etc.
5. Press S1 button to stop the measurement of the
chronograph.
6. Press S2 button to show the last split time Tn (0
to Tn).
7. Press S2 button again, the chronograph is reset
to zero.
8. Press S3 button to return to the normal time mode.
NORMAL TIME
S3
S3
STOPWATCH
S1
START
S3
ALARM
S3
SECOND TIME ZONE
S3
HOW TO SET NORMAL TIME/
■
S3
TIMER
CALENDAR
1. While in the normal time mode, press S2 button
once. The second digits start to flash.
2. While the second digits are selected (flashing),
press S1 button to reset the seconds to 00. If you
press S1 button while the second count is in the
range between 30 and 59, the seconds are reset
to 00 and 1 is added to minutes. If the second
count is in the range between 00 and 29, the
seconds are reset to 00 but the minute count is
unchanged.
3. Press S3 button to move on to the next setting.
SECONDS
S3
12 /2 4- HOU R
FORMAT
S3
DAY
MINUTESHOURS
S3
S3S3
DATE
S3
MONTH
S3
S2
S2
STOP
S2
S1
S2
LAP
S1
LORUSNREZ022C.indd1 2016/12/0915:09
HOW TO SET ALARM TIME
■
1. You can set alarm with hours and minutes. When
the alarm is on, the alarm (BI-BI) sounds for 20
seconds at the preset time. Press S1, S2 or S3
button to stop the alarm after it starts sound.
Alarm is available in one time zone only (T1 or
T2).
2. From the normal time mode, press S3 button 2
times to enter the alarm mode.
3. To change the alarm setting, press S2 button. The
hour digits start flashing. To adjust the value, press
S1 button.
4. To move on to the minute setting, press S3 button.
To adjust the value, press S1 button.
5. To set the time zone, press S3 button. “AL. T1” or
“AL. T2” will flash. Select the time zone by pressing
S1 button.
PRESS S3
2 TIMES
NORMAL TIME
S3
TIMER HAS EXPIRED
S1
to stop
PRESS S3
3 TIMES
S2
S2
RELOAD
TIMER AND
SET
TIMER
S2
HOUR SETTING BY
PRESSING S1
S3
NORMAL TIME
S3
S2
TIME ZONE SETTING
BY PRESSING S1
HOW TO SET SECOND ZONE TIME
■
1. From the normal time mode, press S3 button 4
times to enter the second time zone mode.
2. Press S2 button to start the setting procedure.
The hour digits start flashing.
ALARM MODE
HOUR SETTING BY
PRESSING S1
S3
MINUTE SETTNG BY
PRESSING S1
S2
S3
3. To adjust the value, press S1 button (+1 hour).
4. Press S3 button once to move on to the minute
setting.
5. To adjust the value, press S1 button (+30 minutes
or -30 minutes).
6. Press S2 button to confirm the setting.
7. Press S3 button to retur n to the normal time mode.
PRESS S3
4 TIMES
NORMAL TIME
S3
ALARM & CHIME ON/OFF
■
From the normal time mode, press S3 button 2
times to enter the alarm mode.
Press S1 button to turn on or off the ALARM and
HOURLY CHIME signals.
NORMAL TIME
S3
S1
SECOND TIME ZONE
S2
HOUR SETTING BY
PRESSING S1 (+1 HOUR)
S3
S2
MINUTE SETTING BY PRESSING S1
(+30 MINUTES)
ALARM
PRESS S3
2 TIMES
S1
S1
S1
indicated hourly chime is on
indicated alarm is on
HOW TO USE EL BACKLIGHT
■
In any mode press S4 button to illuminate the
display for about 3 seconds.
Note:
1. The backlight of the watch employs an electroluminescent (EL) light, which tends to lose
illuminating power after very long use.
2. The illumination provided by backlight may be
hard to see when viewed under direct sunlight.
HOW TO USE TIMER
■
TO SET THE COUNTDOWN TIMER
1. From the normal time mode, press S3 button 3
times to enter the timer mode.
2. While in the timer mode, press S2 button. The hour
digit starts to flash.
3. Press S3 button to change the selection of setting.
4. Press S1 button to adjust the value. Holding S1
button down can fasten the process.
5. After you set the countdown time, press S2 button
to return to the timer mode.
BEGIN COUNT DOWN
S1
SETTING IS COMPLETED
MINUTE SETTING BY
PRESSING S1
S3
S2
SECOND SETTING BY
PRESSING S1
TO USE THE COUNTDOWN TIMER
1. Press S1 button while in the timer mode to start
the countdown timer.
2. Press S1 button again to stop the countdown
timer.
3. While in the timer mode, press S2 button to reset
the countdown time to its starting value and to
start to countdown automatically or while in the
timer mode, press S2 button and then press S1
button to reset the countdown time.
4. From 3 minutes prior to the expiry time, the alarm
(BI BI) beeps each time when the second digits
reach “0” or “30”.
5. Within 10 seconds to the expiry time, the alarm
(BI) beeps per second.
6. When the timer expires, the alarm (BI-BI-BI) beeps
for 10 seconds. It may be silenced by pressing S1,
S2 or S3 button.
BATTERY CHANGE
■
The batteries which power your watch should last
approximately 2 years. However, because they
are inserted at the factory, the actual life of the
batteries once in your possession may be less than
2 years.
Be sure to replace the batteries to prevent any
possible malfunction as soon as they run down. To
replace the batteries, we recommend taking the
watch to a local watch repair shop.
Note: If the alarm is used for more than 20
seconds a day, the hourly time signal more
than 24 times a day, the stopwatch more
than once a day and/or the illuminating
light for more than 1 second a day, the
battery life may be less than the specified
period.
CARE OF YOUR LORUS WATCH
■
This watch contains precise electronic
components. Never attempt to open the case or
remove the back cover.
• BATTERY
CAUTION
Do n o t ex p o se th e o l d bat t ery to f i re or
recharge it. Keep it at a place beyond the
reach of chil dren. If a child swallows it, consult
a doctor immediately.
• WATER RESISTANT
Condition
Indication
on the dial/
case back
Indication
WATER
RESISTANT
WATER
RESISTANT
(50M/5 BAR
WATER
RESISTANT
(
100M/10 BAR
or above
* If your watch is 200 M/20 BAR, 100 M/10 BAR or
50 M/5 BAR water resistant, it is so indicated on
the dial/case back.
of use
No
Accidental
contact
with water,
splashes
and rain
)
Swimming
and taking
such as
a shower
NO
YES
YES YES NO NO
YES
diving
NO
NO NO NO
YES YES NO
(
Skin
NO
Scuba
diving
NO
• Do not operate the buttons when the watch is wet.
• If the watch is exposed to salt water, rinse it in
fresh water and then wipe it thoroughly dry.
• Should you find any water or condensation inside
the watch, immediately have it checked. Water
can corrode electric parts inside the case.
Caution:
Leather straps are not water resistant except
so indicated, even if the watch head is water
resistant.
• ALLERGIC REACTION
Because the case and band touch the skin
directly, it is important to clean them regularly. If
not, shirt sleeves may be stained and those with
delicate skin may develop a rash. Please wear
the watch with some play to avoid any possible
allergic reaction. If you develop a rash on your
wrist, stop wearing and consult a physician.
• MAGNETISM
Your watch will be adversely affected by strong
magnetism. Keep it away from close contact with
magnetic objects.
• SHOCKS AND VIBRATIONS
Your watch may be worn for normal sports
activities, but be careful not to drop it or hit it on
hard surfaces.
• TEMPERATURE
Your watch is preadjusted so that constant
accuracy may be insured at normal tem pera ture.
• CLEANING
Use only a soft cloth and clean water for
cleaning your watch. Never use chemicals, as the
waterproof gasket will corrode.
SERVICE
■
When your LORUS watch requires repair or
servicing, please see the enclosed WARRANTY/
GUARANTEE.
Printed in China
LORUSNREZ022C.indd2 2016/12/0915:09
Loading...