Rev: 04.10.2014
Page 1
Touch Audio VD300WR Owners Manual
TABLE OF CONTENTS
System 3
Safety Information 3
System Specications 3
System Controls 4
System Wiring Ports 5
System LCD Display 5
Wireless Remote Controls 6
Installation 7
Speaker Wiring Harness 8
Operation 9
Remote 9
Touch Audio 11
Radio Mode 11
Weather Band 12
Programming 12
TV System 12
Power Resume 12
Auto Play 12
TV Type 12
Rating 13
Default 13
Language Setup 13
Audio Setup 13
Video Setup 14
Speaker Setup 14
Troubleshooting 15
Rev: 04.10.2014
Page 2
Touch Audio VD300WR Owners Manual
System
Safety Information
The “WARNING” symbol above is a sign that a service or maintenance procedure has a safety risk involved and may
cause death or serious injury if not performed safely and within the parameters set forth in this manual.
Always wear eye protection when performing service or maintenance to the vehicle. Other safety equipment to
consider would be hearing protection, gloves and possibly a full face shield, depending on the nature of the service.
This manual provides general service and maintenance procedures. Many variables can change the circumstances
of the service procedure, i.e., the degree of difficulty involved in the service operation and the ability level of the
individual performing the operation. This manual cannot begin to plot out procedures for every possibility, but
will provide the general instructions for effectively servicing the vehicle. In the event the skill level required or the
procedure too difficult, a certified technician should be consulted before performing the necessary service. Failure
to correctly service the vehicle may result in death, injury or voiding the warranty.
System Specifications
Feature Specification
Laser 650um Wave Length
Video Auto/NTSC
Frequency Response 20 Hz - 20 KHz
Signal/Noise Ratio >95 dB
Dynamic Range >80 dB (1 KHz)
Output Level - 1vp-p
Video Out
Load Impedance - 75 Imbalance
Negative Polarity
Power Supply DC 12-14.4 V
Power Consumption <50 W
Dimensions (WxHxD) 218mm x 185mm x 169mm
Weight Approx. 2kg
AM Frequency AM 520 ~ 1710 KHz
FM Frequency FM 87.5 ~ 108 MHz
CH1 - 162.400 MHz
CH2 - 162.425 MHz
CH3 - 162.450 MHz
WB CH1 - CH7 MHz
Frequency Range
CH4 - 162.475 MHz
CH5 - 162.500 MHz
CH6 - 162.525 MHz
CH7 - 162.550 MHz
Output Power 200 W PMPO
Rev: 04.10.2014
Page 3
Touch Audio VD300WR Owners Manual
System Controls
Fig. 1
G
A
I
J
B
C
H
D
E
F
K
L
M
N
Callout Description
A Power
B Reset (Must remove screw cover first)
C A/B/C Speaker Outputs
D Store/ Clock
E USB/ SD/ Band
F Mode
G LCD Display
H Stop/ Play/ Pause/ Fast Forward/ Rewind
I Eject
J Remote Sensor
K Snooze/ Preset
L Bass Boost
M Volume Up/ Volume Down
P
O
Rev: 04.10.2014
N SD/ MMC Card Port
O USB Port
P Auxiliary In
Page 4
Touch Audio VD300WR Owners Manual
System Wiring Ports
Fig. 2
C
E
B
D
A
Callout Description
A Wiring Harness Port
B Automotive Antenna Port (AM/FM/WB)
C Wired Remote Port
D Auxiliary IN (R) TV Audio Input
E Auxiliary IN (L) TV Audio Input
F CVBS (3 Video Output)
NOTE: The wired remote with a 20ft cable is optional and plugs into Fig. 2C.
System LCD Display
A
B
C
D
G
H
F
I
J
Fig. 3
Q
P
S
T
U
V
O
W
E
K
F
Callout Description
A Auxiliary In Mode
B SD/MMC Card Play
C DVD Disc Play
D USB Port Play
E MP3/WMA Play
F CD Play
G Snooze Mode
H FM Stereo Audio Mode
I FM Mono Audio Mode
J A/B/C Speaker Outputs
K Track/Preset Number
L FM Mode
L
N
R
X
M
Callout Description
M PM Mode
N AM Mode
O WB Mode
P Treble
Q Bass
R Disc/Radio/Clock Time
S Memory
T NOAA
U MHz/kHz Mode
V Alarm
W Mute
X Play/Pause
Rev: 04.10.2014
Page 5
Touch Audio VD300WR Owners Manual
Wireless Remote Controls
A
E
M
Q
I
U
Y
J
N
R
V
Z
B
Fig. 4
C
D
H
F
G
L
K
P
O
S
T
X
W
AA
BB
CC
Callout Description
A Power
B Mute
C Alarm
D Eject
E Mode
F Band/ Function
G Memory/ Clock Adjust
H Volume Increase
I Setup
J Up Arrow
K Play/ Pause
DD
EE
FF
Callout Description
Q Repeat
R Down Arrow
S Stop
T Subtitle
U Menu
V Tone
W Program
X Title
Y Rewind
Z Fast Forward
AA Previous
Rev: 04.10.2014
L Volume Decrease
M Channel Decrease/ Left Arrow
N Enter/ Snooze
O Channel Increase/ Right Arrow
P Language
Page 6
BB Next
CC A
DD B
EE C
FF Zoom
Touch Audio VD300WR Owners Manual
Installation
Fig. 5
7.2"
7.67"
2.16 " 2.16 "
Accessories included:
• Wireless Remote
• FM Antenna (Pig Tail)
• RCA Cable (Video)
• Batteries (x2)
• Mounting Screws (x6)
• Wiring Harness (DC Power and Speakers)
8.86"
5.86"
5.9"
7.08"
• DC Power Extension (Red and Black Wires)
Mounting the Touch Audio:
1. Remove the screw covers.
2. Connect all wires and test the radio.
Connecting the speakers wrong will cause distortion and damage the power amplifier.
3. Mount the radio in the wall or cabinet.
4. Screw the unit in place, replace screw covers.
Rev: 04.10.2014
Page 7
Touch Audio VD300WR Owners Manual
Speaker Wiring Harness
NOTE: Wrong connection or reversed polarity (+/-) can cause distortion and damage the power amplifier.
Black A-Right (-)
White C-Left (+)
Red A-Right (+)
Yellow B-Right (-)
Violet A-Left (-)
Grey B-Right (+)
Yellow/Green A-Left (+)
Rev: 04.10.2014
Orange C-Left (-)
Brown C-Right (+)
Blue B-Left (+)
Pink C-Right (-)
15A Fuse
Red +12V
Power 12V+
Green B-Left (-)
Power In Red #16 AWG Power 12V (+)
Power In Black #16 AWG Power 12V (-)
Power 12V-
Black Ground
Page 8
Touch Audio VD300WR Owners Manual
Operation
Remote
1. Power
A. Select power on or standby.
2. Setup
A. The setup screen will appear for Touch Audio settings.
NOTE: If pressed during DVD playback it will take you to the setup menu and auto pause the DVD.
3. Program
A. Saves the desired program.
4. Mode
A. Cycles through WB, auxiliary, radio and disc playback.
5. Band/Function
A. Cycle through radio modes including; FM, AM, Tuner and auxiliary.
6. Language Select
A. Press to select a language for instructions and press again to select disc language.
7. Alarm
A. Set an alarm.
8. Bass/Tone
A. Turn on bass boost.
9. Memory/Clock Adjust
A. Press to save current radio stations and set the clock time.
10. A
A. Select speaker channel A.
11. B
A. Select speaker channel B.
12. C
A. Select speaker channel C.
13. Subtitle
A. Turns on subtitles and cycles subtitle languages.
14. Up
A. Selects and changes modes and features setup.
15. Down
A. Selects and changes modes and features setup.
16. Channel Down /Left
A. Changes channel down and selects options in menu.
17. Channel Up /Right
A. Changes channel up and selects options in menu.
18. Snooze/Enter
A. Confirms selection and snoozes for 9 minutes.
Rev: 04.10.2014
Page 9
Touch Audio VD300WR Owners Manual
19. Volume Up
A. Increases the volume output.
20. Volume Down
A. Decreases the volume output.
21. Eject
A. Removes disc.
22. Menu
A. Switches to menu mode.
NOTE: DVD playback must be stopped before entering menu mode.
23. Title
A. Returns to the selection menu of DVD playback.
24. Mute
A. Reduces audio output to 0.
25. Stop
A. Stops playback , press play/pause to resume.
26. Play/Pause
A. Enters/returns normal playback. When in playback mode press to pause playback.
27. Repeat
A. Repeats current chapter or track. Press it twice to repeat the current disc or title.
28. Rewind
A. Reverses playback with no audio. Press multiple times to increase reversal speed.
29. Fast Forward
A. Increases playback speed with no audio. Press multiple times to increase playback speed.
30. Previous
A. Skips back to previous chapter or track.
31. Next
A. Skips forward to next chapter or track.
32. Zoom
A. Magnifies image during VCD/SVD/DVD playback.
Rev: 04.10.2014
Page 10
Touch Audio VD300WR Owners Manual
Touch Audio
1. When radio is in stand-by mode, touch any button and the panel will light temporarily.
2. Press power to turn the unit on.
3. Touch mode to cycle through auxiliary, radio and disk playback.
A. To use USB or SD, unit must be on disk playback mode, then press USB/SD.
B. To switch between AM and FM, unit must be on radio mode, then press band to cycle.
I. Press preset to view the stations saved on the unit.
a. To store a station in the presets, press and hold store for 2 seconds and the station will
begin to flash.
b. Press store again to save the station to the preset, the station will stop flashing when it
has been saved.
II. To select a preset, press preset and cycle through till the preset desired is shown and press
play.
NOTE: There are 20 presets for AM and FM.
C. While on weather band mode use fast forward/rewind on the Touch Audio or up/down on the
remote to cycle through the channels in your state.
NOTE: Weather band alarm (NOAA) is active on radio, auxiliary and in standby modes only. It will last 2
minutes then turn off automatically.
D. To use DVD and CD playback unit must be on disk playback mode.
I. If there is a disk in the Touch Audio, press eject to remove it.
II. Insert a disk and it will automatically be loaded.
III. Once a disk is inserted follow the on-screen instructions to play the DVD or CD.
4. Press A, B, or C to change the speaker outputs.
NOTE: Channel A is two speakers, B is four speakers and C is six speakers.
5. Press bass boost to activate bass.
A. Use remote tone button to adjust bass and treble levels.
Radio Mode
This unit has a presetting of 10 FM and 10 AM stations. Once in radio mode:
1. Press band to choose between FM, AM, and weather band.
2. Press up/down on the remote or fast forward/rewind on the unit to select desired frequency.
3. Memory on the remote or store on the unit can memorize/store a station in the presets.
A. Press memory/store and the frequency will begin to flash.
B. Press memory/store again to save the frequency to a preset, the frequency will stop flashing when
it has been saved.
4. Press previous/next on the remote or fast forward/reverse on the unit to cycle station presets.
NOTE: If there is a weak signal adjust the antennae to the most adequate position.
Rev: 04.10.2014
Page 11
Touch Audio VD300WR Owners Manual
Weather Band
Once in weather band mode:
1. Press fast forward/rewind on the Touch Audio or up/down on the remote to cycle through the
channels in your state.
To set weather alarm:
1. Set the weather band to the local weather frequency.
2. Turn radio off.
NOTE: When the radio is off the weather band will display on the LCD. When there is a weather alert the
alarm will go off and the light and radio will turn on to the weather band's frequency.
To turn off weather alarm:
NOTE: Radio must be on.
1. Press the mode button to select NOAA function.
2. Press the alarm button on the remote to turn the alarm off.
NOTE: Alarm is on when the alarm icon on the LCD is displayed and off when it isn't.
Programming
TV System
Choose the color system setting according to the TV.
1. Auto - When the Touch Audio is connected to a multi-system TV.
2. NTSC - When the Touch Audio is connected to a NTSC TV.
3. PAL - When the Touch Audio is connected to a PAL TV.
4. PAL60 - When the Touch Audio is connected to a PAL60 TV.
NOTE: Default setting is NTSC.
Power Resume
If the power resume setting is on - when the Touch Audio is in stop, no disk state, or on a frozen frame for more
than 60 seconds, the screen saver will be displayed to protect the screen from damage.
Auto Play
If the auto play setting is on - when a disk enters the Touch Audio it will play automatically.
TV Type
1. 16:9 (Wide Screen) - This setting is for wide screen TVs to maximize pixels for better viewing quality.
2. 4:3 LB (Letter Box) - This setting is for normal TVs and will show the movie in its normal aspect ratio.
Could possibly have black bars at the top and bottom of the TV.
3. 4:3 PS (Pan and Scan) - This setting is for normal TVs and will use the entire TV screen while holding
aspect ratio. Some of the picture may be lost of the sides.
NOTE: The aspect ratio chosen should relate to the recorded disk format as some images may not be
displayed if native ration is not selected.
Rev: 04.10.2014
Page 12
Touch Audio VD300WR Owners Manual
Rating
The rating setting will limit the disks that are playable by the rating set by the user. The rating varies from "Kid Safe"
to "Adult". The default setting is "View All" which nullifies the rating limit.
NOTE: If the password option is locked, you cannot set the ratings limit; the rating limit does not work when
the password option is unlocked.
Default
Choose this option to return all setup options to factory settings.
Language Setup
1. On screen display language setup:
A. Highlight the OSD Language option and press enter on the remote.
B. Use the up/down arrows on the remote to designate the language desired.
C. Press enter on the remote to select the language for the on screen display.
2. Audio language setup:
A. Highlight the Audio Language option and press enter on the remote.
B. Use the up/down arrows on the remote to designate the language desired.
C. Press enter on the remote to select the language for the audio.
3. Subtitle language setup:
A. Highlight the Subtitle Language option and press enter on the remote.
B. Use the up/down arrows on the remote to designate the language desired.
C. Press enter on the remote to select the language for the subtitles.
4. Menu language setup:
A. Highlight the Menu Language option and press enter on the remote.
B. Use the up/down arrows on the remote to designate the language desired.
C. Press enter on the remote to select the language for the menus.
NOTE: If the desired language is not available on a disk, the Touch Audio will display the default language of
Chinese.
Audio Setup
1. Audio output setup:
A. Highlight the Audio Out option and press enter on the remote.
B. Use the up/down arrows on the remote to designate the output mode desired.
C. Press enter on the remote to select the audio output mode designated.
2. Key setup:
Rev: 04.10.2014
A. Highlight the Key option and press enter on the remote.
B. Use the up/down arrows on the remote to designate the key output desired.
C. Press enter on the remote to select the key output designated.
Page 13
Touch Audio VD300WR Owners Manual
Video Setup
1. Brightness setup:
A. Highlight the Brightness option and press enter on the remote.
B. Use the up/down arrows on the remote to designate the brightness level desired.
C. Press enter on the remote to select the brightness level designated.
2. Contrast setup:
A. Highlight the Contrast option and press enter on the remote.
B. Use the up/down arrows on the remote to designate the contrast level desired.
C. Press enter on the remote to select the contrast level designated.
3. Hue setup:
A. Highlight the Hue option and press enter on the remote.
B. Use the up/down arrows on the remote to designate the hue level desired.
C. Press enter on the remote to select the hue level designated.
4. Saturation setup:
A. Highlight the Saturation option and press enter on the remote.
B. Use the up/down arrows on the remote to designate the saturation level desired.
C. Press enter on the remote to select the saturation level designated.
Speaker Setup
1. Down mix setup:
A. Highlight the Down Mix option and press enter on the remote.
B. Use the up/down arrows on the remote to designate the down mix output desired. Speaker down
mix options include:
I. LT/RT
II. Stereo
III. VSS
C. Press enter on the remote to select the down mix output designated.
a. Output will create a theatre audio output if the disk's audio was encoded in Pro Logic
Dolby Digital Format.
a. Output will have two channels of output coming from the left and right soundtrack .
a. Output will use a 5.1 format if it was encoded in 5.1 channels.
Rev: 04.10.2014
Page 14
Touch Audio VD300WR Owners Manual
Troubleshooting
Problem Probable Cause Corrective Action
Unit frozen/ Touch pad does not
respond
No sound
No picture
Disk does not play
Wireless remote does not work
System overloaded
Loose connection
Setup does not support audio
mode or speaker channel
selected
Unit in incorrect mode Set unit to correct mode and retry.
Loose connection
Malfunctioning TV
Disk was loaded incorrectly
Disk is damaged or dirty Clean or replace disk.
Interference between remote
and unit
Remote battery is dead Replace/recharge battery.
Remove left side screw cover and press
the Reset button.
Check connections between the unit and
speakers; reconnect.
Check the audio mode and speaker
channel selected and make sure the setup
supports it.
Check connections between unit and TV;
reconnect.
Check TV with different inputs to verify it's
working properly. Repair or replace.
Remove disk and re-insert into unit label
side up.
Move obstacle and/or point remote
directly at the wireless remote sensor .
Rev: 04.10.2014
Page 15
Touch Audio VD300WR Owners Manual
All information contained within may be distributed as a full document only, unless otherwise permitted by
explicit consent of Lippert Components Inc. to distribute individual parts.
All information contained within is subject to change without notice. New editions will be posted on www.lci1.
com and can be downloaded for free. Information contained within is considered factual until made obsolete
by a *NEW* revision.
Please recycle all obsolete materials.
For all concerns or questions, please contact
Lippert Components, Inc.
Ph: (574) 537-8900 Web: www.lci1.com Email: warranty@lci1.com
Rev: 04.10.2014
Page 16
Touch Audio VD300WR Owners Manual
Loading...