Lippert Components TI-200 Operation And Programming Manual

MULTI-FUNCTION WIRELESS CONTROLLER

OPERATION AND PROGRAMMING INSTRUCTIONS

ELECTRONICS

Operation

1. Locate the LCI Wireless Remote and press the silver
“Home” button to begin.

2. When the keypad appears on the screen, enter the
4-digit PIN by pressing the corresponding numbers
on the touch screen (Fig. 1).

TI-200

Fig. 1

HOME

Button

Fig. 2

Menu Screen Options

1. The menu screen will show the first four function
options. Select one or press the “Next” button for
more options (Fig. 2).

2. To return to previous menu screen press the “Prev”
button (Fig. 3).

NEXT

Button

Fig. 3

PREV

Button

Rev: 09.14.2016

Page 1

TI-200

Rev: 09.14.2016

Page 2

TI-200 Rev: 09.14.2016

Page 3

TI-200

MULTI-FUNCTION WIRELESS CONTROLLER

OPERATION AND PROGRAMMING INSTRUCTIONS

TI-200

ELECTRONICS

MULTI-FUNCTION WIRELESS CONTROLLER

OPERATION AND PROGRAMMING INSTRUCTIONS

TI-200

ELECTRONICS

Fig. 4

Fig. 5

To operate slides, awnings, etc.

1. Press component button on menu screen to enter function
operations screen. This screen will display: on- off, or arrow
up- down, or arrow in- out button options (Fig. 5). To return to
previous screen, press the “Home” button (Fig. 1).

2. The remote will enter “Sleep Mode” after 60 seconds of inactivity.

Entering configure mode on (handheld) remote

To assign titles to the functions to be used:

1. Press the CONFIG button on the touch screen (Fig. 7).

HOME

button

Fig.7

Fig. 8

SELECT
button

Left arrow

Right arrow

Programming

You will need: Wireless Remote (300951) and Multi-function board (305117, 305119, 305120, 305121)

CONFIG

button

Fig. 6

Wireless

Remote

Multi-function

Board

2. This screen will display (Fig. 8):

3. Use left or right arrow (Fig. 8) to scroll through the

options to desired function title.

4. Once the proper title for desired function is on the
screen, press the SELECT button (Fig. 8).

5. Repeat steps for all functions to be used. For any
function that will NOT be used, select the NONE title
option then press SELECT.

3. Light functions can be turned on and off by pressing the button on
the menu screen (Fig. 4).

Rev: 09.14.2016

Page 4

TI-200 Rev: 09.14.2016

Page 5

TI-200

MULTI-FUNCTION WIRELESS CONTROLLER

OPERATION AND PROGRAMMING INSTRUCTIONS

TI-200

ELECTRONICS

MULTI-FUNCTION WIRELESS CONTROLLER

OPERATION AND PROGRAMMING INSTRUCTIONS

TI-200

ELECTRONICS

Fig. 12

8. Review and, if correct, press and hold the

black button on the multi-function board
AND then press the “Sync Remote” button
on the touch screen. The multi-function
board will “click” when the function titles
have been transmitted properly (Fig. 13).

Fig. 13

Fig. 10

Fig. 9

Fig. 11

6. If the remote was purchased before

7/13/2014 refer to Step A, if it was purchased
after that refer to Step B.
A. After all the functions have been

assigned a “title,” the next screen will ask:
"Configure Leveler?" If you are equipped
and want to have leveling available on
your transmitter, select YES. If not, select
NO at this time (Fig. 9).

B. After all the functions have been

assigned a “title,” the next screen will ask:
“Configure Leveler Type 1?” (Fig. 10) and
then "Configure Leveler Type 2?" (Fig.

11) will appear. If syncing the transmitter
to a LCI Level Up, Ground Control or
Motorized Dual Sensor system select
“Yes” for Type 1 and “No” for Type 2. If
you will not be syncing the transmitter
to either of these leveling systems select
“No” for both Type 1 and Type 2.

7. The next screen will show all the assigned
titles for all the functions (Fig. 12).

NOTE: Contact OEM for fuse assignment procedure. To be performed by authorized RV Technician only.

To reset PIN Code

1. Press "HOME" button to turn on transmitter.

2. Press and release "HOME" button five times.

3. Press "CONFIG" (Fig. 14).

Fig. 15

Fig. 16

4. The screen will ask you if you want to reset the screen lock

PIN code (Fig. 15).

Fig. 14

5. The screen will notify you that a PIN has been reset (Fig. 16).

CONFIG

button

MULTI-FUNCTION WIRELESS CONTROLLER

OPERATION AND PROGRAMMING INSTRUCTIONS

ELECTRONICS

6. Press "Home" button. Touch "Set PIN" button (Fig. 17).

TI-200

Fig. 17

SET PIN

button

Fig. 18

7. Enter 4-digit code of your choice (Fig. 18).

8. Touch "Save" button (Fig. 19).

Fig. 19

As a supplier of components to the RV industry, safety, education and customer satisfaction are our primary concerns. Should you
have any questions, please do not hesitate to contact us at [phone] or by email at [e-mail]. Self-help tips,
technical documents, product videos and a training class schedule are available at www.lci1.com or by downloading the MyLCI app.

Rev: 09.14.2016

Page 6

SAVE

button

TI-200