Linksys WPS54G User Manual 2
A Division of Cisco Systems, Inc.
1
GHz
2.4
802.11g
Wireless
®
Package Contents
• Wireless-G PrintServer
• Setup Wizard CD-ROM
•User Guide on CD-ROM
•USB 2.0 Cable
•Network Cable
• Power Supply
• Quick Installation
• Registration Card
Wireless-G
PrintServer
Quick Installation
Connect the PrintServer
Before starting the physical
installation, note the PrintServer’s
default name. The default name is
shown in the Server field on the
sticker located on the PrintServer’s
back panel.
A Use the USB cable to connect
your USB printer to the
PrintServer’s USB Printer port.
B If you are connecting the
PrintServer to your wired
network, then plug one end of
the Ethernet network cable into
the PrintServer’s Ethernet port.
Then connect the other end to
your router or switch.
C Power on your printer.
D Plug the power adapter into
the PrintServer’s Power port.
Then plug the other end into
an electrical outlet.
A
C
D
2
A
Configure the PrintServer
Insert the Setup CD-ROM into
the computer’s CD-ROM drive.
The Setup Wizard should run
automatically. If it does not,
click Start and choose Run. In
the field that appears,
enter D:\setupWizard.exe (if
“D” is the letter of your
CD-ROM drive).
B On the Welcome screen, click
Setup Wizard.
C The Setup Wizard will search for
the PrintServer. After it has been
found, the Wireless-G
PrintServer Setup screen will
appear. If this is the first time
you have run the Setup Wizard,
make sure that List only new
(unconfigured) Print Servers is
selected and your PrintServer is
listed by its default server
name. If you have previously
configured the PrintServer,
select List all compatible Print
Servers. Click Next.
D On the Basic Settings screen,
you may change the Device
Name and Domain Name
settings if you want. Then
click Next.
B
C
D
E The IP Settings screen will
appear. If your network uses a
router that automatically
assigns IP addresses, select
Automatically obtain an IP
address (DHCP) and click
Next. If you need to assign the
PrintServer a static IP address,
select Set IP configuration
manually, and enter the IP
Address, Subnet Mask, and
Gateway in the fields provided.
Then click Next.
F On the Set PrintServer’s
Password screen, enter the
PrintServer’s default password,
admin, in the Current
Password field. Enter a new
password in the New Password
field, and enter it again in the
Verify Password field.
Click Next.
G On the Wireless Settings
screen, enter your wireless
network’s SSID or name. If your
network is set to ad-hoc mode,
select the channel at which
the network broadcasts its
wireless signal. For the Network
Type setting, select
infrastructure if the PrintServer
will communicate using an
access point or wireless router.
Select Ad-Hoc if the PrintServer
will communicate directly with
wireless-equipped computers.
Click Next.
E
F
G
Model No.
Model No.
WPS54G
3
Install and Configure the
PrintServer’s Driver
On the Wireless Security
H
Settings screen, select a level
of WEP encryption, 64 Bit Keys
or 128 Bit Keys. Then enter a
Passphrase to automatically
generate a WEP key. Then
click Next.
If you would like to enter your
WEP key manually, leave the
Passphrase field blank and
enter the WEP key on the next
screen. Then click Next.
I If you used a Passphrase, then
a WEP key will appear on the
following screen. Otherwise,
enter your WEP key in the Key 1
field. Click Next.
J On the Confirmation screen,
make sure your settings are
correct. Click Yes to save your
new settings.
K On the Congratulations
screen, click User Install to
install the PrintServer’s driver.
J
H
I
Linksys recommends that you set up
your printer and install your printer’s
driver before you install the
PrintServer’s driver.
A On the Print Server Driver Setup
Welcome screen, click Next.
B On the Choose Destination
Location screen, select the
location where the driver’s
folder will be installed. If you
want the folder to be installed
in a different location, click
Browse and select the
location. Click Next.
C The Select Program Folder
screen will appear. An icon will
be added to the program
folder listed. If you want, you
may change the name of the
program folder. Click Next.
A
B
C
D After the driver is installed, the
Setup Complete screen will
appear. Make sure Configure
Print Driver now is selected.
Click Next to end the driver
installation and begin the driver
configuration.
E Double-click the Print Driver
Setup icon on your desktop. If
you do not see the icon, click
Start, Programs, Print Server
Utility, and Print Driver Setup.
F Read the Information screen,
and click OK.
G On the Printer Port Setup
screen, select a printer port to
add, and click Next.
H You will be informed that the
PrintServer Port has been
added successfully. Click OK.
D
F
G
I The Configure Printer Port
screen will appear. Your
installed printer(s) will appear in
the Existing Printers field. Select
the printer you want, and click
the Connect button to
associate the printer with your
selected printer port. To add
another printer, click Add New
Printer and follow the onscreen instructions.
J When you have finished
configuring the PrintServer’s
driver, click Close on the Printer
Port Setup screen.
Congratulations! The installation of
the PrintServer is complete.
I
For additional information or troubleshooting
help, refer to the User Guide on the Setup CDROM. You can also call or e-mail for further
support.
24-hour Technical Support
800-326-7114
(toll-free from US or Canada)
E-mail Support
support@linksys.com
Website
http://www.linksys.com or
http://support.linksys.com
RMA (Return Merchandise Authorization)
http://www.linksys.com/support
FTP Site
ftp://ftp.linksys.com
Sales Information
800-546-5797 (800-LINKSYS)
Model No.
K
Linksys is a registered trademark or trademark of
Cisco Systems, Inc. and/or its affiliates in the U.S.
and certain other countries. Copyright © 2004
Cisco Systems, Inc. All rights reserved.
WPS54G-QI-40917A JL
Loading...