Linear DRQP Quick Start Manual

Delta-3 Series

GATE OPERATOR

24 V RADIO POWER

RELAY

DRQP RECEIVER

COMMON

WALL BUTTON

INPUT VOLTAGE REQUIREMENT 18 TO 24 VOLTS AC/DC

GOLD WIRE

SILVER WIRE

DRQP

DIGITAL GATE RECEIVER

Installation Instructions

(800) 421-1587 • www.linearcorp.com

DESCRIPTION

The DRQP is a high-sensitivity, short-range radio receiver that operates in conjunction with the 9-inch local antenna (supplied) or the EXA-GP remote antenna (not included). The DRQP is designed for use with automatic gate operators or systems where a remote antenna is needed.

All of the Delta-3 transmitters, including the two and fou r-channel transmitters, are compatible with the the DRQP. The Delta-3 radio format provides 256 different digital codes. The codes are set using the 8-position coding switches in the un its. In order to avoid the posibility of duplicating codes in adjacent systems, factory set codes should not be used. In addition, among the valid codes available, four others should not b e used. These include: al l keys set O N or OFF and key s set alternating ON/ OFF. Receiver s are normal ly powered wi th 24 volts AC/DC from the gate operator.

The DRQP has a built-in “F” connector and is supplied with a 9-inch local ant enna. The EXA-GP Remote Antenna may be used to enhance the operational range of the DRQP.

STEP 1A

Receiver code setting. Locate the receiver coding

switch which is recessed in the ba ck o f t he receiver case. To set a code, select any valid combination of ON and OFF positions for the switch keys numbered 1 through 8. Use a paper clip to set the eight keys on your receiver.

POWER INPUT WIRE

CODING SWITCH

SWITCHES IN RECEIVER

THIS SWITCH HAS 6, 3 & 2 ON

STEP 1B

Transmitter code setting. Locate the coding

switch on the transmitter and set the eight keys identical to those on the receiver. Be sure they are b oth code d from l eft to rig ht! Be sure they are identical! If using a t wo o r four-cha nne l transmitte r refer to the coding instructions included with the transmitt er for proper system coding.

REMOVE BATTERY ACCESS DOOR

SWITCHES IN TRANSMITTER

CODING SWITCH

THIS SWITCH HAS 2, 3 & 6 ON

STEP 4

isn’t going to be mounted directly to th e operator terminals, an optional mounting bracket is supplied. It can be installed two ways

Optional Receiver mounting bracket. If the receiver

onto the DRQP case. Screw the bracket to a wall or stud and snap the receiver onto it. Attach the 9-inch antenna or the EXA-GP antenna coaxial cable to the “F” co nnector.

LOCATION 2

BRACKET CAN MOUNT IN TWO PLACES

LOCATION 1

ANTENNA "F" CONNECTOR

STEP 2

Connect receiver output. Connect the output

terminals (1 & 2) to the appropriate activation terminals on the gate operator.

WALL BUTTON

GATE OPERATOR

COMMON

DRQP RECEIVER

COM.

N/O

N/C

STEP 5

Test receiver.

each transmitter and verify that the receiver triggers the operator.

W ARNING! BE SURE GATE AREA IS CLEAR OF OBSTRUCTIONS

RELAY

24 V RADIO POWER

Be sure gate area is clear.

PRESS TRANSM ITTER BU TTON TO TES T

Activate

STEP 3

Connect receiver to 24V power. Connect the wh ite

power input wires to the 24V and Common terminals on the gate operator. If using DC power, gold wire (+), silver wire (-).

LIMITED WARRANTY

This product is warranted to the consumer against defects in material and workmanship for one year from the date of purchase. This warranty applies to first retail buyers of new devices. Warrantor will repair, or at its option, replace, any device it finds that requires service under this warranty, and will return the repaired or replaced device to the consumer at the warrantor’s cost. For warranty service and shipping instructions contact warrantor at the address shown below. Devices must be sent to warrantor for service at owner’s expense. The remedies provid ed by this warranty ar e exclusive. Impl ied warranties under state law are to the one year period of this written warranty. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you . In or der to be protected by this warranty, save your proof of purchase and send copy with equipment should repair be required. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other important details.

IMPORTANT !!!

Linear radio controls provide a reliable communications link and fill an important need in portable wireless signaling. However, there are some limitations which must be observed.

For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as

✶

Part 15 devices. As such, they have limited transmitter power and therefore limited range. A receiver cannot respond to more than one transmitted signal at a time and may be blocked by

✶

radio signals that occur on or near their operating frequencies, regardless of code settings. Changes or modifications to the device may void FCC compliance.

✶

Infrequently used radio links should be tested regularly to protect against undetected interference

✶

or fault. A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale

✶

distributor or dealer, and these facts should be communicated to the ultimate users.