Lincoln TOWN CAR 2003 Owner Manual

Introduction 4

Instrument Cluster 10

Warning and control lights 10 Gauges 15

Entertainment Systems 17

AM/FM stereo cassette with CD 17 CD changer 21 Navigation system 24

Climate Controls 70

Dual automatic temperature control 70

Lights 74

Headlamps 74 Turn signal control 78 Bulb replacement 79

Driver Controls 83

Windshield wiper/washer control 83 Steering wheel adjustment 85 Power windows 97 Mirrors 98 Speed control 99 Message center 104

Locks and Security 113

Locks 113 Anti-theft system 123

Table of Contents

Seating and Safety Restraints 128

Seating 128 Safety restraints 133 Air bags 147 Child restraints 155

Driving 166

Starting 166 Brakes 170 Traction control/AdvanceTrac 172 Air suspension 173 Transmission operation 174 Vehicle loading 180 Trailer towing 181

Roadside Emergencies 185

Getting roadside assistance 185 Hazard flasher switch 186 Fuel pump shut-off switch 186 Fuses and relays 187 Changing tires 194 Jump starting 199 Wrecker towing 204

Customer Assistance 205

Reporting safety defects (U.S. only) 214

Cleaning 215

Maintenance and Specifications 222

Engine compartment 224 Engine oil 225 Battery 229 Fuel information 237 Air filter(s) 251 Refill capacities 256 Lubricant specifications 257

Table of Contents

Accessories 263

Index 266

All rights reserved. Reproduction by any means, electronic or mechanical including photocopying, recording or by any information storage and retrieval system or translation in whole or part is not permitted without written authorization from Ford Motor Company. Ford may change the contents without notice and without incurring obligation.

Introduction

CALIFORNIA Proposition 65 Warning

WARNING: Engine exhaust, some of its constituents, and

certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

CONGRATULATIONS

Congratulations on acquiring your new Lincoln. Please take the time to get well acquainted with your vehicle by reading this handbook. The more you know and understand about your vehicle the greater the safety and pleasure you will derive from driving it.

For more information on Ford Motor Company and its products visit the following website:

• In the United States: www.ford.com

• In Canada: www.ford.ca

• In Mexico: www.ford.com.mx

• In Australia: www.ford.com.au

Additional owner information is given in separate publications.

This Owner’s Guide describes every option and model variant available and therefore some of the items covered may not apply to your particular vehicle. Furthermore, due to printing cycles it may describe options before they are generally available.

Remember to pass on the Owner’s Guide when reselling the vehicle. It is an integral part of the vehicle.

Fuel pump shut-off switch In the event of an accident the

safety switch will automatically cut off the fuel supply to the engine. The switch can also be activated through sudden vibration (e.g. collision when parking). To reset the switch, refer to the Fuel pump shut-off switch in the Roadside emergencies chapter.

Introduction

SAFETY AND ENVIRONMENT PROTECTION

Warning symbols in this guide

How can you reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed.

Warning symbols on your vehicle

When you see this symbol, it is imperative that you consult the relevant section of this guide before touching or attempting adjustment of any kind.

Protecting the environment

We must all play our part in protecting the environment. Correct vehicle usage and the authorized disposal of waste cleaning and lubrication materials are significant steps towards this aim. Information in this respect is highlighted in this guide with the tree symbol.

BREAKING-IN YOUR VEHICLE

Your vehicle does not need an extensive break-in. Try not to drive continuously at the same speed for the first 1,600 km (1,000 miles) of new vehicle operation. Vary your speed to allow parts to adjust themselves to other parts.

Drive your new vehicle at least 800 km (500 miles) before towing a trailer.

Do not add friction modifier compounds or special break-in oils during the first few thousand kilometers (miles) of operation, since these additives may prevent piston ring seating. See Engine oil in the Maintenance and specifications chapter for more information on oil usage.

Introduction

SPECIAL NOTICES

Emission warranty

The New Vehicle Limited Warranty includes Bumper-to-Bumper Coverage, Safety Restraint Coverage, Corrosion Coverage, and 7.3L Power Stroke Diesel Engine Coverage. In addition, your vehicle is eligible for Emissions Defect and Emissions Performance Warranties. For a detailed description of what is covered and what is not covered, refer to the Warranty Guide that is provided to you along with your Owner’s Guide.

Data Recording

Computers in your vehicle are capable of recording detailed data potentially including but not limited to information such as:

• the use of restraint systems including seat belts by the driver and passengers,

• information about the performance of various systems and modules in the vehicle, and

• information related to engine, throttle, steering, brake or other system status.

Any of this information could potentially include information regarding how the driver operates the vehicle potentially including but not limited to information regarding vehicle speed, brake or accelerator application or steering input. This information may be stored during regular operation or in a crash or near crash event.

This stored information may be read out and used by:

• Ford Motor Company.

• service and repair facilities.

• law enforcement or government agencies.

• others who may assert a right or obtain your consent to know such

information.

Introduction

Special instructions

For your added safety, your vehicle is fitted with sophisticated electronic controls.

Please read the section Supplemental Restraint System (SRS) in the Seating and safety restraints chapter. Failure to follow

the specific warnings and instructions could result in personal injury.

Front seat mounted rear facing child or infant seats should NEVER be used in front of a passenger side air bag unless the

air bag can be and is turned OFF.

MIDDLE EAST/NORTH AFRICA VEHICLE SPECIFIC INFORMATION

For your particular global region, your vehicle may be equipped with features and options that are different from the ones that are described in this Owner Guide; therefore, a supplement has been supplied that complements this book. By referring to the pages in the provided supplement, you can properly identify those features, recommendations and specifications that are unique to your vehicle. Refer to this Owner

Guide for all other required information and warnings.

Introduction

These are some of the symbols you may see on your vehicle.

Vehicle Symbol Glossary

Safety Alert

Fasten Safety Belt Air Bag-Front

Air Bag-Side Child Seat

Child Seat Installation Warning

Child Seat Tether Anchor

Anti-Lock Brake System

Traction Control AdvanceTrac娂

Master Lighting Switch Hazard Warning Flasher

Fog Lamps-Front Fuse Compartment

See Owner’s Guide

Child Seat Lower Anchor

Brake System

Brake Fluid Non-Petroleum Based

Fuel Pump Reset Windshield Wash/Wipe

Windshield Defrost/Demist

Rear Window Defrost/Demist

Vehicle Symbol Glossary

Introduction

Power Windows Front/Rear

Child Safety Door Lock/Unlock

Power Window Lockout

Interior Luggage Compartment Release Symbol

Panic Alarm Engine Oil

Engine Coolant

Engine Coolant Temperature

Do Not Open When Hot Battery

Avoid Smoking, Flames, or Sparks

Battery Acid

Explosive Gas Fan Warning

Power Steering Fluid

Maintain Correct Fluid Level

Emission System Engine Air Filter

MAX

MIN

Passenger Compartment Air Filter

Jack

Check fuel cap Low tire warning

Instrument Cluster

WARNING LIGHTS AND CHIMES

Warning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains on after starting the vehicle, have the respective system inspected immediately.

Service engine soon: The Service engine soon indicator light

illuminates when the ignition is first turned to the ON position to check the bulb. Solid illumination after the engine is started indicates the On Board Diagnostics System (OBD-II) has detected a malfunction. Refer to On board diagnostics (OBD-II) in the Maintenance and Specifications chapter. If the light is blinking, engine misfire is occurring which could damage your catalytic converter. Drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced immediately.

SERVICE

ENGINE

SOON

Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter, the fuel system, interior

floor coverings or other vehicle components, possibly causing a fire.

Instrument Cluster

Check fuel cap: Illuminates when the fuel cap may not be properly installed. Continued driving with this light on may cause the Service engine soon warning light to come on. Refer to Fuel filler cap in the

Maintenance and Specifications

chapter.

Brake system warning light: To confirm the brake system warning light is functional, it will momentarily illuminate when the ignition is turned to the ON position when the engine is not running, or in a position between ON and START, or by applying the parking brake when the ignition is turned to the ON position. If the brake system warning light does not illuminate at this time, seek service immediately from your dealership. Illumination after releasing the parking brake indicates low brake fluid level and the brake system should be inspected immediately by your servicing dealership.

Driving a vehicle with the brake system warning light on is

dangerous. A significant decrease in braking performance may occur. It will take you longer to stop the vehicle. Have the vehicle checked by your dealer immediately.

Anti-lock brake system: If the ABS light stays illuminated or continues to flash, a malfunction has been detected, have the system serviced immediately. Normal braking is still functional unless the brake warning light also is illuminated.

Air bag readiness: If this light fails to illuminate when ignition is turned to ON, continues to flash or remains on, have the system serviced immediately. A chime will also sound when a malfunction in the supplemental restraint system has been detected.

ABS

AIR

BAG

Instrument Cluster

Safety belt: Reminds you to fasten your safety belt. A chime will also sound to remind you to fasten your safety belt, refer to the Seating and Safety Restraints chapter.

Charging system: Illuminates when the battery is not charging properly.

Engine oil pressure: Illuminates when the oil pressure falls below the normal range, refer to Engine oil in the Maintenance and specifications chapter.

Engine coolant temperature:

Illuminates when the engine coolant temperature is high. Stop the vehicle as soon as possible , switch off the engine and let cool. Refer to Engine coolant in the Maintenance and specifications chapter.

Never remove the coolant recovery cap while the engine is

running or hot.

Autolamp: Illuminates when the autolamps are turned on.

Traction control娂/AdvanceTrac娂 active: Flashes when the Traction

control娂 system is active. If the light remains on, have the system serviced immediately, refer to the Driving chapter for more information.

Air suspension: Illuminates when the air suspension is turned OFF or the air suspension system requires servicing.

Washer: Illuminates when the windshield washer fluid is low.

Speed control: Illuminates when the speed control is activated. Turns off when the speed control system is deactivated.

O/D off: Illuminates when the overdrive function of the transmission has been turned OFF using the transmission control switch (TCS), refer to the Driving chapter. If the light flashes steadily, have the system serviced immediately.

Door ajar: Illuminates when any door is open (or not fully closed).

Instrument Cluster

Trunk ajar: Illuminates when the trunk is not completely closed. This light will flash and sound a tone for one second, then the light remains on.

Turn signal: Illuminates when the left or right turn signal or the hazard lights are turned on. If the indicators stay on or flash faster, check for a burned out bulb.

High beams: Illuminates when the high beam headlamps are turned on.

Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (and the key is not in the ignition) and the driver’s door is opened.

Key-in-ignition warning chime: Sounds when the key is left in the ignition in the OFF/LOCK or ACC position and the driver’s door is opened.

Turn signal chime (if equipped): Sounds when the turn signal lever has been activated to signal a turn and not turned off after the vehicle is driven more than 0.8 km (1/2 mile).

GAUGES

Speedometer: Indicates the current vehicle speed.

Select SPEED from the message center to display the digital speedometer on the left hand side of the cluster. Refer to the Message Center in the Driver Controls chapter for more information on the Trip A and B feature.

Instrument Cluster

Engine coolant temperature gauge: Indicates engine coolant

temperature. At normal operating temperature, the needle will be in the normal range (between “H” and

“C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the engine and let the engine cool.

Instrument Cluster

Never remove the coolant reservoir cap while the engine is

running or hot.

Odometer: Registers the total kilometers (miles) of the vehicle.

Fuel gauge: Indicates approximately how much fuel is left in the fuel tank (when the ignition is in the ON position). The fuel gauge may vary slightly when the vehicle is in motion or on a grade.

Refer to Filling the tank in the

Maintenance and Specifications

chapter for more information..

The FUEL DOOR icon and arrow indicates which side of the vehicle the fuel door is located.

Entertainment Systems

AUDIOPHILE AM/FM STEREO/CASSETTE/SINGLE CD

MUTE

AM/FM

TUNE

SEEK

TAPE

SCAN

AUTO

SET

RDS

REW

BASS

DSP

SEL

SIDE

BAL

COMP

PREMIUM AM/FM STEREO/CASSETTE/SINGLE CD

TREB

FADE

SHUF

AM/FM

MUTE

TUNE

SEEK

TAPE

SCAN

AUTO

RDS

REW

SET

SEL

SIDE

BASS

BAL

COMP

TREB

FADE

SHUF

Entertainment Systems

1. Eject: Press to eject a tape.

2. Eject: Press to eject a CD.

3. Bass: Allows you to increase or decrease the audio system’s bass output. Press BASS then press SEL

to decrease

Treble: Allows you to increase or decrease the audio system’s treble output. Press TREB then press SEL

to decrease

4. Balance: Allows you to shift speaker sound between the right and left speakers. Press BAL then

press SEL to shift sound to the left

Fade: Allows you to shift speaker sound between the front and rear speakers. Press FADE then press

SEL to shift the sound to the rear

5. COMP (Compression): In CD mode, press to bring soft and loud passages together for a more consistent listening level.

SHUF (Shuffle): Press to play CD tracks in random order.

or increase the bass levels.

or increase the treble levels.

or right .

or the front .

6. Select: Use to adjust bass, treble, balance and fade levels.

7. Side 1–2: Press to change sides on the tape.

Dolby: reduction: Reduces tape noise and

hiss; press to activate/deactivate.

Dolby威 noise

Entertainment Systems

8. REW (Rewind): Works in tape and CD modes.

In tape mode, radio play continues until rewind is stopped (with the TAPE control) or the beginning of the tape is reached.

In CD mode, REW control reverses the CD within the current track.

FF (fast forward): Works in tape and CD modes.

In the tape mode, tape direction automatically reverses when the end of the tape is reached.

In CD mode, FF advances the CD within the current track.

9. Digital signal processing (if equipped): Press to adjust the occupancy modes between the following:.

• ALL SEATS

• DRIVER SEAT

• REAR SEATS

RDS: (Radio Data System): Allows you to access FM stations which are RDS- equipped. Press RDS then SEL to select from:

Traffic — Allows you to receive traffic announcements and control their volume level. Traffic information is not available in most U.S.

markets.

Show — Allows you to view the frequency and program type of the chosen radio station.

The Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC) recommend that FM radio broadcasters use RDS technology to transmit information. FM radio stations are independently operated and individually elect to use RDS technology to transmit station ID and program type as desired.

10. Autoset: Press to set first six strong stations into AM, FM1 or FM2 memory buttons; press again to return to normal stations.

Entertainment Systems

11. Scan: Works in radio, tape and CD modes. Press SCAN for a brief sampling of radio stations, tape selections or CD tracks.

12. Seek: Works in radio, tape and CD modes. Press to access the

previous radio station, tape selection or CD track.

13. Tune: Works in radio mode. Press to manually advance up or down the frequency band.

14. AM/FM/CD: Press AM/FM to select a radio frequency. Press while in tape or CD mode to return to radio mode. Press CD to enter CD mode and to play a CD already in the system.

15. Mute mode: Press to mute the playing media.

16. Power/volume: Press to turn the system on/off. Turn to raise/lower the volume.

or next listenable

17. Tape: Press to play the tape.

18. CD door: Insert the disc with the playing side down and printed side up.

19. Tape door: Insert the tape facing the right.

CD CHANGER (IF EQUIPPED)

Your CD changer is located in the trunk.

1. Slide the door to access the CD changer magazine.

Entertainment Systems

2. Press

3. Pull the lever to remove a CD tray from the magazine.

to eject the magazine.

Entertainment Systems

4. Insert one disc into each CD tray of the magazine (up to 6 discs). Ensure that the label side is facing up.

If you pull too hard on the disc holder, the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine.

5. Insert each CD tray, with the disc loaded, all the way into the CD magazine.

6. Insert the CD magazine into the changer.

7. Slide the door to the left to close.

Use only compact discs containing this mark.

The magazine does not need to be full for the changer to operate.

Entertainment Systems

Radio power must be turned on to play the CDs in the changer. The magazine may be stored in the glove compartment when not being used.

The CD magazine may be inserted or ejected with the radio power off.

Do not insert any promotional (odd shaped or sized) discs, or discs with removable labels into the CD player as jamming may occur.

RADIO FREQUENCIES

AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and Telecommunications Commission (CRTC). Those frequencies are:

AM - 530, 540–1700, 1710 kHz FM- 87.7, 87.9–107.7, 107.9 MHz

RADIO RECEPTION FACTORS

There are three factors that can affect radio reception:

• Distance/strength: The further you travel from an FM station, the weaker the signal and the weaker the reception.

• Terrain: Hills, mountains, tall buildings, power lines, electric fences, traffic lights and thunderstorms can interfere with your reception.

• Station overload: When you pass a broadcast tower, a stronger signal may overtake a weaker one and play while the weak station frequency is displayed.

CASSETTE/PLAYER CARE

Do:

• Use only cassettes that are 90 minutes long or less.

• Tighten very loose tapes by inserting a finger or pencil into the hole

and turning the hub.

• Remove loose labels before inserting tapes.

• Allow tapes which have been subjected to extreme heat, humidity or

cold to reach a moderate temperature before playing.

• Clean the cassette player head with a cassette cleaning cartridge after 10–12 hours of play to maintain good sound/operation.

Don’t:

• Expose tapes to direct sunlight, extreme humidity, heat or cold.

• Leave tapes in the cassette player for a long time when not being

played.

Entertainment Systems

CD/CD PLAYER CARE

Do:

• Handle discs by their edges only. Never touch the playing surface.

• Inspect discs before playing. Clean only with an approved CD cleaner

and wipe from the center out.

Don’t:

• Expose discs to direct sunlight or heat sources for extended periods of time.

• Insert more than one disc into each slot of the CD changer magazine.

• Clean using a circular motion.

CD units are designed to play commercially pressed 12 cm (4.75 in) audio compact discs only. Due to technical incompatibility, certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Irregular shaped CDs, CDs with a scratch protection film attached, and CDs with homemade paper (adhesive) labels should not be inserted into the CD player. The label may peel and cause the CD to become jammed. It is recommended that homemade CDs be identified with permanent felt tip marker rather than adhesive labels. Ball point pens may damage CDs. Please contact your dealer for further information.

AUDIO SYSTEM WARRANTY AND SERVICE

Refer to the Warranty Guide for audio system warranty information. If service is necessary, see your dealer or qualified technician.

LINCOLN NAVIGATION SYSTEM (IF EQUIPPED)

Your vehicle may be equipped with a Lincoln Navigation System which allows you to listen to the radio, play CDs and also navigate the vehicle using a navigation DVD.

Your system has a large range of features, yet is easy to use. Guidance is shown on the display screen and is supplemented with voice prompts. The display screen provides full information for operating the system through use of menus, text screens and map displays. Screen selections are made by touching the desired selection on the screen.

Entertainment Systems

1. VOL-PUSH: Press to turn the system ON/OFF. Turn to adjust the

audio volume level.

2. AUDIO: Press to enter audio mode and access radio, CD, CDDJ, DVD

(if equipped) settings.

3. MAP: Press to enter map mode and view your current vehicle position

on the map. Press and hold to obtain additional position information.

4. DEST: Press to enter Destination Entry mode. This allows you to

enter a destination and route to it. With an active route, pressing DEST allows the user to request a Detour, display entire route, select route preferences, or change or cancel the destination.

5. MENU: Press to access system settings such as display, brightness,

clock mode, etc.

6. CD OPEN CLOSE: Press to open/close the display screen and access

the CD player.

Cold temperature advisory

When operating the system below 32° Fahrenheit (0° Celsius), the display screen requires 20–30 minutes warm-up to achieve maximum brightness. Ensure that the system display setting is set to DAY mode until maximum brightness is achieved (refer to Menu mode section). Once maximum brightness is achieved, revert to AUTO mode display setting.

Entertainment Systems

Initial map display

After pressing AGREE to the initial WARNING screen, you will move into the initial map screen which shows the current vehicle location. Pressing the globe icon will take you to the user settings — audible feedback, navigation units, language and clock.

Quick Start — How to get going

To play a radio station:

1. Ensure that the vehicle ignition is on.

2. Press AUDIO.

3. Select AM, FM1 or FM2.

4. Press TUNE to adjust manually up (

band.

5. Press SEEK to find the next strong station up (

Note: If PTY (program type) is selected, the station selection will be limited. Refer to Program Type (PTY) for further information.

) or down ( ) the frequency

) or down ( ).

Entertainment Systems

To play a previously loaded CD:

1. Ensure that the vehicle ignition is on.

2. Press AUDIO.

3. Press CD to select a CD which is already loaded. (NO CD will appear

in the display if there are not CDs loaded into the system). Use the memory presets (1–6) to select the desired CD.

4. CD will begin to play.

To load CDs:

1. Press CD OPEN CLOSE at the

bottom of the screen to load a CD. (The screen will open).

2. Press LOAD and select the desired slot. Or, press and hold LOAD to

auto load all available slots. The slot indicator lights blink rate will increase when the system is ready to accept a disc. Push CD OPEN CLOSE to close the screen. Once closed, the CD will begin to play.

3. Use the touch controls to advance tracks, scan, pause, etc. The small

red lights below the CD slot will blink faster when the system is ready to accept a disc.

To use the Navigation system:

1. Ensure that the vehicle ignition is on, and the navigation DVD is

loaded into the navigation DVD player. Refer to Loading the map DVD for navigation DVD locations.

2. Press DEST. The warning screen will appear. After reading, press

AGREE. The screen will show a map with your current location. Press DEST again.

Entertainment Systems

VOL PUSH

AUDIO

MAP

DEST

Most functions are unavailable while vehicle is in motion. Please read the navigation handbook for operating instructions. Always drive safely and obey traffic laws.

CD OPEN • CLOSE

WARNING

Agree

3. Select the desired type of destination entry; Address, Point of Interest;

Previous Dest; Special Memory Point; Select from map; Memory Point and Freeway Ent/Exit. Enter the required information.

4. Press DEST at the bottom of the

map screen.

5. Choose the desired route by

pressing the NEXT button (if it appears). There can be up to three alternative routes.

6. Press START to begin the

navigation guidance.

To adjust the voice guidance volume:

Press On/Off to turn the voice guidance option on/off. Use the numeric keys (1–7) to determine the volume level of the guidance voice prompts.

Voice activated commands (if equipped)

Your Lincoln Navigation System (LNS) may be equipped with a voice activated feature which allows you to “speak” certain commands to the system. Speaking clearly will help to ensure that the system correctly responds to your commands.

Entertainment Systems

At any time, you may say these commands:

• AM

• FM1

• FM2

• CD

• DVD (if equipped)

During normal radio operation, you may say:

• Seek up

• Seek down

During CD play with the in-dash 6 disc player:

• Track up

• Track down

• Disc up

• Disc down

While in navigation map mode, the following commands are available by voice activation:

• Zoom in

• Zoom out

• Minimum scale

• Maximum scale

While in navigation destination (DEST) mode, the following commands are available by voice activation:

• Home

• Detour

While in navigation map mode, the following commands are available by voice activation:

• Gas station

• Gas

• Hospital

• Police station

• Restaurant

• Hotel

Entertainment Systems

Audio mode

Your Lincoln Navigation Audio System has many features including a full range of audio functions. To access these functions, press AUDIO on the main bezel. This will take you into audio mode.

Volume/power control

Press knob to turn the audio system on/off. Turn to raise or lower volume. The levels will be displayed on the screen.

To activate the navigation mode, press MAP or DEST.

To adjust the navigation voice output level, select the NAV MENU button via the map screen.

+ 242 hidden pages