Life Fitness Parabody 807 User Manual
807 BODYSYSTEM
WORKOUT CENTER
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.
CLASS H
PART # 7052601
REV . B
USER’S GUIDE
1
Version: 807107
Revision: 07/09/01
j
TABLE OF CONTENTS
Safety Statement.............2
General Notes..................3
Tools Required................3
Gym Layout.....................4
Parts list..........................5
Assembly Instructions.....6-15
General Maintenance.......16
W arranty Statement..........17
Product Services..............18
Insert-Registration Card
IMPORTANT SAFETY INFORMATION
THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF
EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES!
1. Before using, read all the warnings and instructions
on the use of this machine. Use only for intended
exercise. DO NOT modify the machine.
2. Obtain a medical exam before beginning any
exercise program.
3. Keep body and clothing free of all moving objects.
4. Inspect the machine before use. DO NOT use it if it
appears damaged. DO NOT attempt to fix a broken or
ammed machine. Notify your authorized ParaBody
dealer before use and have repairs made by an
authorized service technician.
6. Never pin the weights or prop plate into an elevated
position. DO NOT use the machine if found in this
condition. DO NOT attempt to fix. Notify your
authorized ParaBody dealer.
7. Inspect cables and their connections before using
machine. Pay particular attention to the cable ends.
DO NOT attempt to fix. Notify your authorized
ParaBody dealer before use and have repairs made by
an authorized service technician.
8. Make sure all spring loaded pull pins are fully
engaged in the adjustment position and fully tighten
thumbscrew before use.
5. Be certain that weight pin is completely inserted.
Use only the pin provided by the manufacturer. If
unsure, call your authorized ParaBody dealer.
9. Children must not be allowed near this machine.
Supervise teenagers.
.
NOTE: In a continual effort to improve our products, specifications are subject to change
2001 Life Fitness, a division of Brunswick Corporation. All rights reserved.
©
ParaBody is a trademark of Brunswick Corporation
www.parabody.com
2
IMPORTANT NOTES
Please note:
* Thank you for purchasing the ParaBody 807 Gym System. Please read these
instructions thoroughly and keep them for future reference. This product must be assembled
on a flat, level surface to assure its proper function.
* This product must be assembled on a flat, level surface to assure its proper function. DO NOT
securely tighten any frame connections until the entire frame has been assembled, unless
otherwise stated.
T ools Required for Assembly
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* Adjustable wrench
* T ape measure
Bolt Length Ruler
NOTE: BOL T LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOLT LENGTH
BOL T LENGTH RULER:
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
345
3
6
1’
2’
3’
4’
1’ 2’ 3’
4’
5’
6’
7’
5’
1 Square = 1’ X 1’
4
PARTS LIST
KEY
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
PA RT #
7058908
6407508
6111002
6406602
6407802
6407302
6407202
6024702
6406401
6406501
6125101
6194601
6654521
6654121
3102909
DESCRIPTION
UPRIGHT FRAME
BENCH FRAME
HEIGHT ADJUSTMENT BAR
WOLFF SLEEVE
BASE LEG
SADDLE
LEG EXTENSION NECK
LEG EXTENSION
HINGE TAB
U-PIN
ROLLER PAD SHAFT
ROLLER PAD
SEAT PAD
BACK PAD
3/8 X 1” BOLT
QTY
1
1
1
1
1
2
1
1
4
2
2
6
1
1
4
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
3102922
3102904
3102910
3102501
3102601
3102802
3102502
6236701
3102804
6412001
6020601
3105401
3109602
6145801
3103101
6416601
3/8 X 2-3/4” BOLT
3/8 X 3” BOLT
1/2 X 3” BOLT
3/8” WASHER
3/8” LOCK WASHER
3/8” LOCK NUT
1/2” WASHER
1-3/4” SQ. END CAP
1/2” LOW HEIGHT LOCK NUT
3/8” SPRING PIN ASSEMBLY
1/2” FLANGE BEARING
3/4” STARLOCK COLLAR
PAL NUT
THUMBSCREW
1-1/4 X 5” GRIP
PARAGLIDE STRIP (8 ct.)
1
2
1
10
4
3
2
4
1
3
2
6
2
6
2
3
32
33
3104301
6405201
3/4” SQ. RUBBER BUMPER
2” SQ. END CAP
5
1
6
25
28
4
10
31
FIGURE 1
STEP 1:
• Attach eight PARAGLIDE STRIPS (31) to the WOLFF SLEEVE (4) (FOUR ON EACH END) as shown in FIGURE 1 using the
following steps:
• Thoroughly clean all surfaces where the PARAGLIDE STRIPS are to be attached.
• Remove the PARAGLIDE STRIPS from the paper backing and firmly apply them to all shown surfaces.
• Insert one U-PIN (10) through the BUSHING of the WOLFF SLEEVE (4) and attach one PAL NUT (28) to the end of the U-PIN
(10) as shown in FIGURE 1.
• SECURELY assemble one 3/8” SPRING PIN ASSEMBLY (25) to the SPRING PIN HOUSING on the WOLFF SLEEVE (4) as
shown in FIGURE 1. (!!! IMPORTANT !!! TIGHTEN THE NUT OF THE SPRING PIN ASSEMBLY SECURELY)
1/2 1/2 1/2 1/2 1/2 1/2
1/2 1/2 1/2 1/2 1/2 1/2
0
0
1
1
2
2
345
345
6
6
6
Loading...