Life Fitness Parabody 663 User Manual
663 660 SECOND STACK OPTION
CLASS H
PART # 7050101
REV . C
USER’S GUIDE
1
WARNING:
Read and follow all directions
for each step to insure proper
assembly of this product.
Version: 663101
Revision: 07/31/01
j
TABLE OF CONTENTS
Safety Statement.............2
General Notes..................3
Tools Required................3
Parts list..........................4
Assembly Instructions.....4-16
General Maintenance.......17
W arranty Statement..........18
Product Services..............19
Insert-Registration Card
IMPORTANT SAFETY INFORMATION
THERE IS A RISK ASSUMED BY INDIVIDUALS WHO USE THIS TYPE OF
EQUIPMENT. TO MINIMIZE RISK FOLLOW THESE RULES!
1. Before using, read all the warnings and instructions
on the use of this machine. Use only for intended
exercise. DO NOT modify the machine.
2. Obtain a medical exam before beginning any
exercise program.
3. Keep body and clothing free of all moving objects.
4. Inspect the machine before use. DO NOT use it if it
appears damaged. DO NOT attempt to fix a broken or
ammed machine. Notify your authorized ParaBody
dealer before use and have repairs made by an
authorized service technician.
6. Never pin the weights or prop plate into an elevated
position. DO NOT use the machine if found in this
condition. DO NOT attempt to fix. Notify your
authorized ParaBody dealer.
7. Inspect cables and their connections before using
machine. Pay particular attention to the cable ends.
DO NOT attempt to fix. Notify your authorized
ParaBody dealer before use and have repairs made by
an authorized service technician.
8. Make sure all spring loaded pull pins are fully
engaged in the adjustment position and fully tighten
thumbscrew before use.
5. Be certain that weight pin is completely inserted.
Use only the pin provided by the manufacturer. If
unsure, call your authorized ParaBody dealer.
9. Children must not be allowed near this machine.
Supervise teenagers.
.
NOTE: In a continual effort to improve our products, specifications are subject to change
2001 LifeFitness, a division of Brunswick Corporation. All rights reserved.
©
ParaBody is a trademark of Brunswick Corporation
www.parabody.com
2
IMPORTANT NOTES
Please note:
* Thank you for purchasing the ParaBody 663 660 Second Stack Option. Please read these
instructions thoroughly and keep them for future reference.
* This product must be assembled on a flat, level surface to assure its proper function. DO NOT
securely tighten any frame connections until the entire frame has been assembled, unless
otherwise stated.
T ools Required for Assembly
* Rubber mallet or hammer
* 3/4” wrench
* 9/16” wrench
* Ratchet with 3/4” and 9/16” sockets
* 7/32” Allen wrench
* Adjustable wrench
* T ape measure
Bolt Length Ruler
NOTE: BOL T LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT.
BOLT LENGTH
BOL T LENGTH RULER:
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
345
3
6
PARTS LIST
1
2
3
4
5
6
7
8
9
PART #
6523401
7095701
7012102
6957302
7032302
3116101
6972201
3108002
3117401
KEY
FIGURE 1
FRONT SHROUD
DESCRIPTION
GUIDE ROD
WEIGHT ST ACK SHAFT
WEIGHT ST ACK SP ACER
HEAD PLA TE
PRESS-ST ACK CABLE
4-1/2” PULLEY
WEIGHT ST ACK PIN
WEIGHT ST ACK CUSHION
CAP PLUG
QTY
2
1
2
1
1
1
1
2
4
KEY
10
11
12
13
14
15
16
17
18
PART #
6978101
3102909
6480301
3102922
3102802
3102503
6939202
6382301
3221702
DESCRIPTION
WEIGHT ST ACK LABEL
3/8 X 1” BOLT
3/8” FLANGE SP ACER
3/8 X 2-3/4” BOLT
3/8” LOCK NUT
3/4” WASHER
WEIGHT PLA TE
WEIGHT PLA TE BUSHING 10 CT .
E-RING
REAR SHROUD
3/8” X 1” BUTTON
HEAD CAP SCREW
QTY
1
1
2
1
1
2
15
3
1
STEP 1
• REMOVE the four 3/8” X 1” BUTTON HEAD CAP SCREWS from the top of the front SHROUD & rear SHROUD. See FIGURE 1.
3/8” X 1” BUTTON
HEAD CAP SCREW
FIGURE 2
STEP 2
• REMOVE the four 3/8” X 1” BUTTON HEAD CAP SCREWS from the bottom of the front SHROUD & rear SHROUD. Remove the
SHROUDS from the 660101 HOME GYM. See FIGURE 2.
4
HEAD
PLATE
CABLE
(7041801)
D-RING
FIGURE 3
STEP 3
• Unscrew the threaded ends of the HEAD PLATE CABLE from the WEIGHT STACK SHAFT & the D-RING and remove HEAD
PLATE CABLE. The HEAD PLATE CABLE will be used later. See FIGURE 3. (NOTE: Remove pulleys for ease of removal.)
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
345
5
6
STEP 4
• Remove the PRESS CABLE (67249) from the KEYHOLE CLEVIS
and ELASTIC CORD. (NOTE: The LA T or LEG EXT CABLE can
be moved over one hole on the D-RING so the KEYHOLE CLEVIS
are evenly spaced .)
FIGURE 4
ELASTIC
CORD
• Discard the KEYHOLE CLEVIS and ELASTIC CORD.
FIGURE 5
3/8” LOCK NUT
2” PULLEY
3/8” HEX NUT
3/8” W ASHER
KEYHOLE
CLEVIS
PRESS CABLE
(67249)
D-RING
TOP BOOM
3/8” THREADED ROD
3/8” W ASHER
3/8” LOCK NUT
3-1/2” PULLEY
STEP 5
• Remove one 3-1/2” PULLEY , one 3/8” THREADED SHAFT , two 3/8” W ASHERS, one 2” PULLEY (two if the 435104 is installed), one
3/8” HEX NUT and two 3/8” LOCK NUTS from the bracket on the TOP BOOM. See FIGURE 5.
• Discard the 3-1/2” PULLEY and the 3/8” THREADED SHAFT .
• (NOTE: If the 100101 LEG PRESS OPTION is installed proceed to STEP 6 otherwise proceed to STEP 7.)
6
Loading...