Life Fitness CLUB SEATED LEG CURL User manual

CLUB SERIES SEATED LEG CURL

Part # 7138301

Rev B

ASSEMBLY INSTRUCTIONS

Revision: 10/12/011

PARTS LIST

Y

#

Y

#

#02ROYAL BLUE
#03SLATE
#04CRANBERRY
#05NORTHWOODS
#06 SPACE BLUE
#07AMERICAN BEAUTY RED
#08SUEDE
#12 BLACK
#13HUNTER GREEN
#14 REGIMENTAL BLUE
#15GINGERSNAP
#16CONCORD
#17URQUOISE
#18 RASPBERRY
#19CROCUS

KE

1A 7041201 CABLE 1 15 3102904 3/8 X 3” BOLT 3
1B 6692601 3 X 2 END CAP 3 16 3102942 3/8 X 3-1/2” BOLT 2
1C 6714901 GUIDE ROD BUSHING 2 17 3102905 3/8 X 3-3/4” BOLT 8
1D 3102903 3/8-16 X 2.5 BOLT 2 18 3102935 3/8 X 4-1/2” BOLT 1
1E 3102933 3/8-16 X 2 BOLT 1 19 3202404 3/8 X 3” BUTTON HEAD BOLT 4
1F 6866701 3/8 RH WASHER 4 20 3233502 1/2 X 3-1/4” SHOULDER BOLT 1
1G 6866601 CAP, RH 20 BLK 4 21 3102807 3/8” LOW HEIGHT LOCK NUT 25
1H 3102807 3/8 NYLOCK NUT LOW HT 3 22 3221501 3/8” ACORN NUT 1

1J 3102514 3/8 WASHER FLAT 2 24 6866701 3/8” RH WASHER 52
1K 3222801 4.5" PULLEY 3 25 3114502 3/8” LOCK WASHER 1

3A 6912001 RUBBER GRIP 2 28 6913801 WEIGHT STACK SELECTOR PIN 1

4A 6946901 ROLLAR PAD 4 30 6866602 WHITE RH CAP 43
4B 3222701 SHAFT COLLAR 2 OR 6866603 PLATINUM 43
4C 3119303 1.25" END CAP 2 31 3222001 1” SHAFT COLLAR 2
4D 6412001 SPRING PIN 1 32 3116001 1-1/4” RUBBER BUMPER 3
4E 6965901 6.5" PLATE ADJ 2 33 6714901 GUIDE ROD BUSHING 2
4F 6965901 6.5" PLATE ADJ " " 34 6912801 2” ACCORDION SLEEVE 1
4G 3234301 SCREW 4 35 6912803 3” ACCORDION SLEEVE 1
4H 6974102 ROLLAR PAD SPPT BLK 1 36 7053701 PLACARD LABEL 1

9A 6947902 ASSY BACK PAD ADJ 1 42 69574xx SEAT PAD 1
9B 6897001 15 POS ADJ PLATE 1 43 6957001 WEIGHT STACK LABEL 1
9C 6897101 ADJ PLATE 1 44 3102940 3/8 X 5” BOLT 1
9D 3234301 SCREW 4 45 3230701 STARLOCK WASHER 4
9E 6912202 HINGE BLK 1 46 6866601 BLACK RH CAP 8
9F 6896901 HINGE PIN 2 47 6861902 TOP COVER 1
10 70448xx ASSY KNEE HOLD DOWN SPPT 1 48 6862102 FRONT SIDE SHROUD BLK 2
11 6923602 HEAD PLATE 1 49 6862007 FRONT SHROUD PLATINUM 1
12 3102901 3/8 X 1-1/4” BOLT 2 50 6922002 FULL REAR SHROUD BLK 1
13 3102903 3/8 X 2-1/2” BOLT 4 OPTION* 6921602 ASSY, FULL FRONT SHROUD 1

PART

1 70435xx TOWER 1 14 3102922 3/8 X 2-3/4” BOLT 6

1I 6480301 3/8 SPACER 4 23 3102514 3/8” SAE WASHER 31

2 70441xx ASSY PIVOT ARM SUPPORT 1 26 6020601 1/2” FLANGE BEARING 2
3 70445xx KNEE HOLD DOWN 1 27 3203501 PILLOW BLOCK 2

4 70457xx ASSY PIVOT ARM 1 29 3108001 WEIGHT STACK CUSHION 2

5 68839xx GUIDE ROD SUPPORT 1 37 7058401 LANGUAGE PLACARD LABEL 1
6 7038602 CAM SHROUD BLK 1 38 69266 GUIDE ROD 2
7 7038802 COUNTER BALANCE BLK 1 39 6887202 10 LB. WEIGHT PLATE (STD) 20
8 70543xx ASSY SEAT SUPPORT 1 40 6888402 15 LB. WEIGHT PLATE (OPT) 10
9 70439xx SEAT FRAME 1 41 68775xx BACK PAD 1

DESCRIPTION QTY KE

PART

DESCRIPTION QTY

*For all 5 digit part numbers you need to add the color at the end.
For shrouds and weldments please use the following codes: German, Poruguese, Spanish, Japaneese, and

xxxxx07 Denotes Platinum Italian.
xxxxx08 Denotes White

*For upholstery, please use the following codes:

**Language placard kit comes with Dutch, French,

3/8 X 2-3/4” 14

30

2

23

1A

1

21

24

3/8 X 3-3/4” 17

FIGURE 1

STEP 1:

• LOOSELY assemble the top of the PIVOT ARM SUPPORT (2) to the TOWER (1) using four RH CAPS (30), two 3/8 X 2-3/4”

BOLTS (14), four 3/8” SAE WASHERS (23), four 3/8” RH WASHERS (24) and two 3/8” LOW HEIGHT LOCK NUTS (21) as
shown in FIGURE 1.

• LOOSELY assemble the bottom of the PIVOT ARM SUPPORT (2) to the TOWER (1) using four RH CAPS (30), two 3/8 X 3-

3/4” BOLTS (17), four 3/8” SAE WASHERS (23), four 3/8” RH WASHERS (24) and two 3/8” LOW HEIGHT LOCK NUTS
(21) as shown in FIGURE 1.

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

4

6

1A

9A

9D

9

9E

9F

9B

9C

21

2

24

3/8 X 3-3/4” 17

30

23

FIGURE 2

STEP 2:

• LOOSEL Y assemble the SEAT FRAME (9) to the PIVOT ARM SUPPORT (2) using four RH CAPS (30), two 3/8 X 3-3/4” BOLTS

(17), four 3/8” SAE WASHERS (23), four 3/8” RH WASHERS (24), and two 3/8” LOW HEIGHT LOCK NUTS (21) as shown in
FIGURE 2.

5

32

30

21

24

2

3/8 X 2-3/4” 14

9

8
23

17 3/8 X 3-3/4”

FIGURE 3

STEP 3:

• LOOSELY assemble the SEAT SUPPORT (8) to the SEAT FRAME (9) using four RH CAPS (30), two 3/8 X 3-3/4” BOLTS (17),

four 3/8” SAE WASHERS (23), four 3/8” RH WASHERS (24) and two 3/8” LOW HEIGHT LOCK NUTS (21) as shown in
FIGURE 3.

• LOOSELY assemble the SEAT SUPPORT (8) to the PIVOT ARM SUPPORT (2) using four RH CAPS (30), two 3/8 X 2-3/4”

BOLTS (14), four 3/8” RH WASHERS (24) and two 3/8” LOW HEIGHT LOCK NUTS (21) as shown in FIGURE 3.

• Assemble one 1-1/4” RUBBER BUMPER (32) to the PIVOT ARM SUPPORT (2) as shown in FIGURE 3.

• Securely tighten all loose frame connections made to this point, then proceed to snap RH

CAPS (30) over the RH WASHERS (24) on all tightened connections.

1/2 1/2 1/2 1/2 1/2 1/2

0

1

2

345

6

6