CLUB SERIES PLA TE TREE
Part # 7189301
Rev B.
ASSEMBLY INSTRUCTIONS
Revision:2/27/021
PARTS LIST
KEY
1
2
3
4
5
PART #
71882
71886
71126
3102922
3102906
DESCRIPTION
FRAME
3 X 2 X 18” TUBE
WEIGHT HORN
3/8 X 2-3/4” BOLT
3/8 X 4” BOLT
T ools Required for Assembly
* Rubber mallet or hammer
* 9/16” wrench
* Ratchet with 9/16” socket
QTY
1
2
6
4
6
KEY
6
7
8
9
10
OR
PART #
3102807
3102514
6866701
6866601
6866602
6866603
DESCRIPTION
3/8” LOW HEIGHT LOCK NUT
3/8” SAE WASHER
3/8” RH WASHER
BLACK RH CAP
WHITE RH CAP
PLA TINUM RH CAP
QTY
10
20
20
12
8
8
Bolt Length Ruler
NOTE: BOL T LENGTH IS MEASURED FROM THE UNDERSIDE OF THE HEAD OF THE BOLT .
BOLT LENGTH
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
345
2
6
4 3/8 X 2-3/4” BOLT
5 3/8 X 4” BOLT
6
3/8” LOW
HEIGHT LOCK
NUT
8
RH
WASHER
9
10
RH CAP
(BLACK/WHITE/PLATINUM)
7
3/8” SAE
WASHER
3
FIGURE 1
10
1
3/8 X 2-3/4” 4
7
8
2
6
STEP 1:
• SECURELY assemble the two 3 X 2 X 18” TUBES (2) to the FRAME (1) using eight RH CAPS (10), four 3/8 X 2-3/4” BOLTS
(4), eight 3/8” SAE WASHERS (7), eight 3/8” RH WASHERS (8) and four 3/8” LOW HEIGHT LOCK NUTS (6) as shown in
FIGURE 1. (IMPORTANT! Note orientation of TUBES.)
1/2 1/2 1/2 1/2 1/2 1/2
0
1
2
345
4
6
FIGURE 2
3/8 X 4” 5
9
7
6
1
3
8
STEP 2:
• SECURELY assemble six WEIGHT HORNS (3) to the FRAME (1) using twelve BLACK RH CAPS (9), six 3/8 X 4” BOLTS (5),
twelve 3/8” SAE WASHERS (7), twelve 3/8” RH WASHERS (8) and six 3/8” LOW HEIGHT LOCK NUTS (6) as shown in FIGURE 2.
5
CAUTION-PLEASE READ
There is a risk assumed by individuals who use this type of equipment. To minimize risk, please
follow these rules:
1. Inspect equipment daily . Tighten all loose connections and replace worn parts immediately.
Failure to do so may result in serious injury.
2. Do not allow minors or children to play on or around this equipment.
3. Exercise with care to avoid injury .
4. Consult your physician before beginning any exercise program.
WARRANTY INFORMATION
10 YEARS STRUCTURUAL FRAME
3 YEARS PILLOW BLOCKS, PULLEYS, WEIGHT PLA TES AND GUIDE RODS
1 YEAR CABLES
90 DA YS UPHOLSTERY
PREVENTATIVE MAINTENANCE TIPS
Action DAILY WEEKLY QUARTERLY BI- ANNUALLY AS NEEDED
CLEAN
Uphol s tery
Guide Rods
Hand Grips
INSPECT
Visual Over all
Cabl e s
Hardware
Frame
Hand Grips
LUBRICATE
Guide Rods
X
X
X
X
X
X
X
X
X
Clean:
• Upholstery with mild soap and water.
• Guide rods with a cotton cloth.
• Hand grips with mild soap and water.
• Frame damage can be repaired with touch-up paint can be purchased from your LifeFitness customer service representative at
(800)351-3737.
Inspect:
• Cables for wear or damage and proper tension (should not exceed 3/4” deflection.) Pay close attention at bends and attachment
points.
• Hardware should be checked for looseness. Tighten as required.
• Frames should be inspected for wear or damage.
• Hand Grips should be checked for wear or damage
Lubricate:
• Lube the Guide Rods. Apply the lubricant to a cotton cloth, then run the cotton cloth up and down the guide rods as needed. Do not
spray lubricant directly on the Guide Rods.
Thank you for purchasing the LifeFitness CLUB SERIES PLA TE TREE. If unsure of proper use of equip-
ment, call your local LifeFitness distributor or call the LifeFitness customer service department at (800)
351-3737.
6
Loading...