Liebherr HCB1060 Design Guide
Design Guide
Fully Integrated Models 24" and 48"
Release 04 2016
Welcome
Liebherr is one of the World’s leading Manufacturers of Premium Refrigeration. For more than 60 years,
Liebherr has specialized in developing and manufacturing first class refrigerators and freezers as well as
wine cabinets. We focus on performance and efficiency as well as keeping food fresher longer.
Produced in Austria and Germany, Liebherr has a full line of premium models tailored specifically for the
North American marketplace to fit any design vision you have for your kitchen.
Our freestanding stainless models are sleek centerpieces that make a definite statement. Our built-in
models are perfect for designs that call for units that slide into cabinet surrounds. And our fully-integrated
models become one with your kitchen design, hidden seamlessly behind your custom cabinetry.
High quality materials, perfectly detailed finishes, precise electronic control systems, elite cooling components, variable speed compressors and the latest production processes ensure energy efficiency and
performance for years to come.
Our superior products offer premium quality, cutting edge design and innovative features that fit with your
busy lifestyle.
Introduction
LIEBHERR WARRANTY PLAN
FULL TWO YEAR WARRANTY - For two years from the date of original purchase, your Liebherr Warranty
covers all parts and labor to repair or replace any part of the product which proves to be defective in materials or workmanship.
FULL FIVE YEAR WARRANTY - For five years from the date of original purchase, your Liebherr Warranty
covers all parts and labor to repair or replace any components that prove to be defective in materials or
workmanship in the sealed system. The "Sealed System" means only the compressor, condenser, evaporator, drier and all connecting tubing.
LIMITED 6TH THROUGH 12TH YEAR WARRANTY - From the 6th through 12th year from the date of
original purchase, your Liebherr Warranty covers all parts that prove to be defective in materials or workmanship in the sealed system (parts only).
For Service and Parts in the U.S.:
PlusOne Solutions, Inc.
Customer Service
If your appliance is not working properly, or if the temperature display reads "F0" to "F9 ”, please call the
numbers listed below.
Give the fault number displayed, together with the
Type Designation,
Service Number and
Appliance Number (Serial Number)
from the model plate, to ensure prompt, accurate servicing. The model plate is located inside the appliance.
3501 Quadrangle Blvd, Suite 120
Orlando, FL 32817
Toll Free: 1-866-LIEBHER or
1-866-543-2437
Service-appliances.us@liebherr.com
www.liebherr-appliances.com
Leave the appliance door closed until the customer service technician arrives to minimize any further cold loss.
For Service and Parts in Canada:
Euro-Parts Canada
39822 Belgrave Road,
BELGRAVE, Ontario, N0G 1E0
Phone: (519) 357-3320
Fax: (519) 357-1326
Toll Free: 1-888-LIEBHER or
1-888-543-2437
www.euro-parts.ca
Need help?
For design related inquiries not addressed in this Design
Guide please email install.americas@liebherr.com
Contents
General Remarks
I. Safety Warnings ....................................................................................................................................... 7
II. Electrical Requirements & Safety .......................................................................................................... 8
III. IceMaker (if equipped) ........................................................................................................................... 8
IV. Area Requirements ................................................................................................................................. 9
V. Safety Regulations .................................................................................................................................. 9
Fully Integrated Models 24" and 48" Models
24" Model: HC 1030, HC 1050B, HC 1070, HC 1080, HC 1021, HCB 1060 .............................................. 10
Ventilation Requirements ......................................................................................................................... 14
Kitchen Cabinet Base Grille ..................................................................................................................... 15
Location Of The Electrical Outlet ............................................................................................................. 15
Unit Dimensions ....................................................................................................................................... 16
Kitchen Cabinet Doors ............................................................................................................................. 17
Definition of the Door Panel Heights ........................................................................................................ 18
HC 1030, HC 1050B, HC 1070, HC 1080, HC 1021, HCB 1060 ................................................................. 19
Kitchen cabinet setup for the water filter ................................................................................................ 20
24" Model: HC 1000B, HC 1001B, HC 700B .............................................................................................. 22
Ventilation Requirements ......................................................................................................................... 24
Kitchen Cabinet Base Grille ..................................................................................................................... 25
Location Of The Electrical Outlet ............................................................................................................. 25
Unit Dimensions ....................................................................................................................................... 26
Kitchen Cabinet Doors ............................................................................................................................. 27
Definition of the Door Panel Heights ........................................................................................................ 28
HC 1000B, HC 1001B .............................................................................................................................. 29
HC 700B ................................................................................................................................................... 30
24" and 48" Models: HF 861 / HRB 1120, SBS 19H1 ................................................................................ 32
Ventilation Requirements ......................................................................................................................... 34
Kitchen Cabinet Base Grille ..................................................................................................................... 35
Location Of The Electrical Outlet ............................................................................................................. 35
Unit Dimensions ....................................................................................................................................... 36
Kitchen cabinet setup for the water filter ................................................................................................. 37
Kitchen Cabinet Doors ............................................................................................................................. 38
Definition of the Door Panel Heights ........................................................................................................ 39
HF 861 / HRB 1120 .................................................................................................................................. 39
General Remarks
I. Safety Warnings
PLEASE READ AND FOLLOW THESE INSTRUCTIONS
This design guide contains Warning and Caution statements. This information is important for safe and
efficient installation.
This design guide is not replacing the use and care manual which contains important information on how to use Liebherr appliances.
Always read and follow all Warning and Caution statements!
indicates a hazardous situation, which if not avoided, will result in death or serious injury.
indicates a hazardous situation, which if not avoided, could result in death or serious injury.
indicates a hazardous situation, which if not avoided, will result in minor or moderate injury.
NOTICE
indicates a hazardous situation, which if not avoided, could result in damage to property.
NOTE
indicates useful advice and tips.
Make sure incoming voltage is the same as the unit rating.
To reduce the risk of fire, electric shock, or personal injury, the installation work and electrical wiring must be done by
a qualified electrician in accordance with all applicable codes and standards, including fire rated construction.
To the Installer
It is very important that the guidelines and instructions are followed in this design guide to ensure proper installation and operation of the unit. The Installation Guidelines section contains important information for making sure the
installation is correct. Read and understand all the information and installation guidelines in this manual before the
unit is installed.
It is also very important to know the Safety Information.
7
General Remarks
II. Electrical Requirements & Safety
Circuit has to be grounded and protected by a circuit
breaker or fuse.
Single installation: Side-by-side installation:
• 115 volt • 115 volt
• 60 hz • 60 hz
• 15 amp • 20 amp
We recommend using a dedicated circuit for each
appliance to prevent circuit overload and the chance of
interruption to the appliance.
The appliances are equipped with a three-prong
(grounding) polarized plug for protection against possible
shock hazards.
Comply with the National Electrical Code as well as local
codes and ordinances when installing the receptacle.
Do not ground to a gas pipe. Check with a
qualified electrician if you are not sure the
appliance is properly grounded. Do not have
a fuse in the neutral or grounding circuit.
III. IceMaker (if equipped)
The icemaker is located in the freezer compartment.
The appliance must be level for the icemaker to function
properly.
If you have hard water, we recommend you install a
water softener. Also, a filter must be installed if the water
contains solids such as sand. All equipment and devices
used to supply the water to the appliance must comply
with the current regulations for your geographical area.
Safety Instructions and Warnings
• Do not attach the water source while the appliance is
connected to an electrical outlet.
• The water quality must comply with the drinking water
regulations for the geographical area where the appliance is located.
• The icemaker is designed exclusively to make ice
cubes in quantities needed by a household and may
only be operated with water appropriate for this purpose.
• All repairs and work on the icemaker may only be done
by customer service personnel or other trained personnel.
Electrocution hazard.
Electrical Grounding Required.
• Do not remove the round grounding prong
from the plug.
• Do not use a two-prong
grounding adapter.
• Do not use an extension cord to connect
power to the unit.
• Do not use a power cord that is frayed or
damged.
• Do not use a power strip.
Failure to follow these instructions may
result in fire, electrical shock or death.
8
Appliances with water connection:
• The water pressure must be between 21.8-87.0 psi (1.5-6
bar). Use a 1/4" OD copper line (not supplied) to connect the water supply to the solenoid valve.
• A shut-off valve, must be installed between the hose
line and the main water supply so that the water supply can be stopped if necessary. Do not install the
shut-off valve behind the refrigeration unit.
• The connection to the water supply may only be made
by a trained and licensed plumber.
• The manufacturer cannot accept liability for damage
caused by equipment or water lines between the solenoid valve and the water supply.
Appliances with water tank:
• Fill the water tank with cold potable water only. Never
use fluids containing sugar such as soft drinks, fruitjuices etc..
• Through the use of filtered, decarbonized water, drinking water with the best possible flavor is achieved,
and this can be used for problem-free production of
ice cubes. This water quality can be achieved using
a table water filter of the kind available in trade retail
outlets.
General Remarks
IV. Area Requirements
Verify the following:
• Floors can support refrigerator’s weight plus approximately 1200 pounds (544 kg) of food weight. Not
all Liebherr products are designed for 1200 pounds
(544 kg) of food. Some units are smaller and total
weights may vary.
• Finished kitchen floor height is level. Refrigerator must
be shimmed to the floor level, or levelled, to make
sure, air vents are not obstructed.
• Remove anything attached to the rear or side walls
that can obstruct refrigerator opening.
• Cutout dimensions are accurate.
• Electrical outlet is in correct location.
Do not install this unit next to any other refrigerator or
freezer except another Liebherr model. Liebherr models
are designed to allow side by side installation. They are
equipped with a heating system to eliminate condensation when units are installed side by side. Installing this
unit next to any other refrigerator or freezer can cause
condensation or cause damage to the Liebherr unit.
NOTICE
To protect the refrigerator from possible
damage, allow the appliance to stand 1/2 to
1 hour in place before turning the electricity
on. This allows the refrigerant and system
lubrication to reach equilibrium.
V. Safety Regulations
The appliance complies with UL250 and CAN/CSA-C
22,2 No. 63-93 (HF 851, HRB 1110) and respectively
CAN/CSA-C22.2 No. 60335-1-11, 60335-2-24-06 and
UL 60335-1, UL 60335-2-24 (HC 1070, HC 1000B, HC
1001B, HRB 1120) and is designed to cool, freeze, store
food as well as make ice (if equipped). It is designed as a
household appliance. If used commercially, the relevant
regulations on commercial use must be observed.
The appliance is set to operate within specific ambient
temperature limits according to its climate rating. These
temperature limits should not be exceeded. The correct climate rating for your appliance is indicated on the
model plate.
This is explained as follows:
Climate
Rating
SN 50°F to 90°F (10°C to 32°C)
N 61°F to 90°F (16°C to 32°C)
ST 61°F to 101°F (16°C to 38°C)
T 61°F to 110°F (16°C to 43°C)
SN-ST
SN-T
Refrigerant circuits are tested for leaks.
Set for Ambient Temperatures of
50°F to 101°F (10°C to 38°C)
50°F to 110°F (10°C to 43°C)
9
Fully Integrated
24" Model: HC 1030, HC 1050B, HC 1070, HC 1080, HC 1021, HCB 1060
24" Model: HC 1030, HC 1050B, HC 1070, HC 1080, HC 1021, HCB 1060
Integrated units are the most stylish option available - they're totally out of sight, fully concealed behind a cabinet door. Installed in
a tall kitchen cupboard, the refrigerator door simply opens in unison with the cupboard door.
HC 1030
Energy Star: certified
Energy consumption p. a.: 395* kWh
respectively 395** kWh
Energy Supply: 115V/60Hz
Total capacity: 9,42 cu ft (267 L)
Refrigerator: 7,02 cu ft (199 L)
Freezer: 2,4 cu ft (68 L)
Climate Rating: SN-T
Door hinges: right / reversable
• Automatic refrigerator and freezer compartment defrosting
• LED light
• Height-adjustable feet at front and levelling rails
• Changeable door gasket
HC 1050B
Energy Star: certified
Energy consumption p. a.: 475* kWh
respectively 407** kWh
Energy Supply: 115V/60Hz
Total capacity: 9,42 cu ft (267 L)
Refrigerator: 7,02 cu ft (199 L)
Freezer: 2,4 cu ft (68 L)
Climate Rating: SN-T
Door hinges: right / reversable
• Automatic refrigerator and freezer compartment defrosting
• LED light
• IceMaker with fixed water connection
• Height-adjustable feet at front and levelling rails
• Changeable door gasket
* Measurement determined according to Appendix A to Subpart B of 10 CFR Part 430
** Measurement determined according to Appendix A1 to Subpart B1 of 10 CRF Part 430
10
Fully Integrated
24" Model: HC 1030, HC 1050B, HC 1070, HC 1080, HC 1021, HCB 1060
HC 1070
Energy Star: certified
Energy consumption p. a.: 475* kWh
respectively 407** kWh
Energy Supply: 115V/60Hz
Total capacity: 9,32 cu ft (264 L)
Refrigerator: 6,92 cu ft (196 L)
Freezer: 2,4 cu ft (68 L)
Climate Rating: SN-T
Door hinges: right / reversable
• Automatic refrigerator and freezer compartment defrosting
• LED light column
• HC 1070 with soft closing system
• IceMaker with water tank
• Height-adjustable feet at front and levelling rails
• Changeable door gasket
HC 1080
Energy Star: certified
Energy consumption p. a.: 475* kWh
respectively 407** kWh
Energy Supply: 115V/60Hz
Total capacity: 9,39 cu ft (266 L)
Refrigerator: 6,99 cu ft (198 L)
Freezer: 2,4 cu ft (68 L)
Climate Rating: SN-T
Door hinges: right / reversable
• Automatic refrigerator and freezer compartment defrosting
• LED light column
• HC 1080 with soft closing system
• IceMaker with fixed water connection
• Height-adjustable feet at front and levelling rails
• Changeable door gasket
11
Fully Integrated
24" Model: HC 1030, HC 1050B, HC 1070, HC 1080, HC 1021, HCB 1060
HC 1021
Energy Star: certified
Energy consumption p. a.: 395* kWh
respectively 395** kWh
Energy Supply: 115V/60Hz
Total capacity: 9.39 cu ft (266 L)
Refrigerator: 6.99 cu ft (198 L)
Freezer: 2,4 cu ft (68 L)
Climate Rating: SN-T
Door hinges: left / reversable
• Automatic refrigerator and freezer compartment defrosting
• LED light column
• HC 1021 with soft closing system
• Height-adjustable feet at front and levelling rails
• Changeable door gasket
HCB 1060
Energy Star: certified
Energy consumption p. a.: 475* kWh
respectively 403** kWh
Energy Supply: 115V/60Hz
Total capacity: 8.71 cu ft (247 L)
Refrigerator: 3.91 cu ft (111 L)
BioFresh: 2.4 cu ft (68 L)
Freezer: 2.4 cu ft (68 L)
Climate Rating: SN-ST
Door hinges: right / reversable
• Automatic refrigerator and freezer compartment defrosting
• LED light column
• HCB 1060 with soft closing system
• BioFresh safes with SoftTelescopic
• IceMaker with fixed water connection
• Height-adjustable feet at front and levelling rails
• Changeable door gasket
* Measurement determined according to Appendix A to Subpart B of 10 CFR Part 430
** Measurement determined according to Appendix A1 to Subpart B1 of 10 CRF Part 430
12
Loading...