Liebert Universal Monitor User Manual

Download

UNIVERSAL MONITOR

MONITORING

USER MANUAL

TABLE OF CONTENTS

1.0 INTRODUCTION

1.1 Methods of Viewing and Configuring the Universal Monitor . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.2 Data Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.3 Optional Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.4 Available Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1.5 Outside Enclosure Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

1.6 Typical Configuration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

1.7 Controller Board Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

1.8 Optional Expansion Board Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

1.9 LED Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

1.10 LED Indicators - Optional Expansion Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

1.11 Typical Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

2.0 INSTALLATION - MAIN BOARD

2.1 Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.1.1 Unpacking and Preliminary Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

2.2 Surface-Mounting the Universal Monitor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.2.1 Mounting the Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

2.3 Flush-Mounting the Universal Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.3.1 Mounting the Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

2.4 Connect Power to the Universal Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.4.1 Input Power Connections - Small Enclosure. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

2.4.2 Termination and Mounting - Large Enclosure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

2.4.3 Connecting the Battery Pack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.0 INSTALLATION - OPTIONAL EXPANSION BOARD

3.1 Installation Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.1.1 Unpacking and Preliminary Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.2 Surface-Mounting the Optional Expansion Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.2.1 Mounting the Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.3 Flush-Mounting the Optional Expansion Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3.3.1 Mounting the Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

3.4 Input Power Connections - Optional Expansion Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

4.0 WIRING AND CONNECTIONS - MAIN BOARD

4.1 Wiring Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

4.2 Connecting Digital Inputs and Digital Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4.2.1 Connecting Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4.2.2 Connecting Digital Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

4.2.3 Setting the Digital Output Jumpers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

4.3 Connecting Analog Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

4.3.1 Setting the 12VDC/24VDC Analog Power Jumper. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

4.3.2 Connecting the Analog Ground . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

4.4 Connecting Common Alarm Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4.5 EIA422 SiteScan Web Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4.6 Communications Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4.6.1 RS232 Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

4.6.2 Phone Line Connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

5.0 WIRING AND CONNECTIONS - OPTIONAL EXPANSION BOARD

5.1 Wiring Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

5.2 Connecting Inputs and Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

5.2.1 Connecting Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

5.2.2 Connecting Digital Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

5.2.3 Setting the Digital Output DIP Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

5.3 Connect to the Universal Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

5.3.1 Connect EIA485 Connectors to Main Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

5.3.2 Enable the Connection via Firmware . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

6.0 OVERVIEW OF MENUS

6.1 Opening Screen Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

6.2 Main Menu Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

6.3 LCD Menu Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

7.0 VIEW STATUS OPTIONS

7.1 View Active Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

7.1.1 Active Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

7.2 View Alarm Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

7.2.1 Alarm Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

7.2.2 Backing Up the Alarm Log (Service Terminal Interface only) . . . . . . . . . . . . . . . . . . . . . . . . . 34

7.3 View Event Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

7.3.1 Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

7.3.2 Backing Up the Event Log (Service Terminal Interface only) . . . . . . . . . . . . . . . . . . . . . . . . . 35

7.4 View Trend Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

7.4.1 Select a Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

7.4.2 View a Trend Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

7.4.3 Backing Up the Trend Log (Service Terminal Interface only) . . . . . . . . . . . . . . . . . . . . . . . . . 36

7.5 View Input Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

7.5.1 Input Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

7.6 View Output Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

7.6.1 Output Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

7.7 View Pager Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

7.7.1 Select a Pager . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

7.7.2 View a Pager Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

7.7.3 View a Pager PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

8.0 SILENCE ALARM & BACKUP LOG FILES (SERVICE TERMINAL INTERFACE)

8.1 Silence Alarm (Service Terminal Interface) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

8.2 Back Up Log Files (Service Terminal Interface only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

9.0 SYSTEM AND CONTROL OPTIONS

9.1 Login . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

9.2 Setup System - Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

9.3 Setup System - Setup Input. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

9.3.1 Change Label (Name of Input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

9.3.2 Define Input as Normally Open or Normally Closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

9.3.3 Define Input as Alarmable or Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

9.3.4 Set Up Alarmable Inputs in Latched or Unlatched Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

9.3.5 Set Up Delay Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

9.4 Setup System - Setup Common Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

9.5 Setup System - Setup Sensor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

9.5.1 Identify the Sensor as Connected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

9.5.2 Change Sensor Label (Name) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

9.5.3 Change Units Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

9.5.4 Change 4 mA Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

9.5.5 Change 20 mA Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

9.5.6 Change Offset Value. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

9.5.7 Define Sensor as Alarmable or Event . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

9.5.8 Set Up Alarmable Sensors in Latched or Unlatched Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

9.5.9 Change Low Setpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

9.5.10 Change High Setpoint . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

9.5.11 Set Up Delay Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

9.6 Setup System - Setup I/O Matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

9.6.1 Set Up Mapping for a Digital Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

9.6.2 Set Up Mapping for an Analog Sensor Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

9.7 Setup System - Setup Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

9.7.1 Change Label (Name of Output) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

9.7.2 Define Main Board Output as Normally Open / Closed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

9.7.3 Set Expansion Board Output by DIP Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

9.7.4 Configure Main Board Output for Loss of Power (“Fail-Safe”) . . . . . . . . . . . . . . . . . . . . . . . . 59

9.8 Setup System - Setup Modem & Pagers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

9.8.1 Modem Setup - Initialization String . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

9.8.2 Modem Setup - Additional Features (Service Terminal Interface only) . . . . . . . . . . . . . . . . . 62

9.8.3 Pager Setup - Pager Number and PIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

9.8.4 Pager Setup - Communications Check (Service Terminal Interface only). . . . . . . . . . . . . . . . 66

9.9 Setup System - Setup System Info . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

9.9.1 Change Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

9.9.2 Change Date & Time/Automatic Daylight Saving Time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

9.9.3 Setup Site ID. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

9.9.4 Connect Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

9.9.5 Backup and Upload Configuration File (Service Terminal Interface only) . . . . . . . . . . . . . . . 71

9.9.6 Setup Serv Ph Num - Enter Phone Number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

9.9.7 Setup Serv Ph Num - Communications Check (Service Terminal Interface only) . . . . . . . . . 75

9.9.8 Factory Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

9.9.9 Perform Firmware Update (Service Terminal Interface only) . . . . . . . . . . . . . . . . . . . . . . . . . 76

9.9.10 Initiate Remote Alarm Test (Service Terminal Interface only) . . . . . . . . . . . . . . . . . . . . . . . . 78

9.10 Setup Exp Board - Optional Expansion Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

9.11 Manual Output Ctrl . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

9.12 Clear Alarms & Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

9.12.1 Clear Active Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

9.12.2 Clear the Alarm Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

9.12.3 Clear the Event Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

9.12.4 Clear the Trend Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

10.0 SPECIFICATIONS

10.1 Universal Monitor Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

10.2 Optional Expansion Board Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

iii

APPENDIX A-SERVICE TERMINAL INTERFACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85

A.1 Comparison of Functions: LCD and Service Terminal Interface. . . . . . . . . . . . . . . . . . . . . . 85

A.2 Connecting to the Service Terminal Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

A.2.1 Connection Methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

A.2.2 Create a Connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 87

A.2.3 Set Up the COM1 Port - Direct Connection Only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88

A.2.4 Set Up the Connection’s Properties. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89

A.2.5 Connect to the Service Terminal Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90

A.3 Overview of Menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

A.3.1 View Status Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

A.3.2 Silence Alarm and Backup Log Files. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

A.3.3 Setup Menu Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91

A.4 View Status Menus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 92

A.4.1 View Active Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93

A.4.2 View Alarm Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 94

A.4.3 View Event Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95

A.4.4 View Trend Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96

A.4.5 View Input Status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97

A.4.6 View Output Status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98

A.4.7 View Pager Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99

A.5 Silence Alarm & Back Up Log Files (Service Terminal Interface only). . . . . . . . . . . . . . . . 100

A.5.1 Silence Alarm (Service Terminal Interface only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100

A.5.2 Back Up Log Files (Service Terminal Interface only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 101

A.6 Setup Menu. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104

A.6.1 Setup Input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106

A.6.2 Setup Common Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108

A.6.3 Setup Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109

A.6.4 Setup I/O Matrix. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111

A.6.5 Setup Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117

A.6.6 Setup Modem & Pagers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119

A.6.7 Setup System Info. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121

A.6.8 Connect Expansion Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127

A.6.9 Override Output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128

A.6.10 Clear Alarms & Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130

APPENDIX B-DEFAULT SETTINGS QUICK REFERENCE GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . 132

FIGURES

Figure 1 Small enclosure—external features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Figure 2 Large enclosure—internal features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Figure 3 Typical Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Figure 4 Example of typical sequence: Analog input reaches high setpoint . . . . . . . . . . . . . . . . . . . . . . . . . 9

Figure 5 Mounting Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Figure 6 Electrical connections to panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Figure 7 Power wiring to TM115 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 8 Power wiring to TM230 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Figure 9 Mounting Dimensions - optional Expansion Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Figure 10 Electrical connections to panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Figure 11 Form C output contact wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Figure 12 LCD Menu overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Figure 13 Menu overview - View Status menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Figure 14 Menu overview - System and Control menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Figure 15 Menu overview - Setup System Info menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

TABLES

Table 1 Controller board components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Table 2 Expansion board components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Table 3 LED indicators summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Table 4 LED indicators summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Table 5 Packing manifest - Universal Monitor main board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Table 6 Packing manifest - optional Expansion Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Table 7 Wiring specifications - main board. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Table 8 Digital output jumper settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Table 9 Wiring specifications - optional Expansion Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Table 10 DIP switch setting - outputs wired as Normally Closed (N.C.) . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Table 11 DIP switch setting - outputs wired as Normally Open (N.O.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Table 12 Guide to Universal Monitor functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Table 13 Primary Functions Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Table 14 Alarm log conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Table 15 Event log conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Table 16 Trend log conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Table 17 Analog input states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Table 18 Digital input states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Table 19 Digital output states . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Table 20 Valid characters for data entry . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Table 21 Default settings - digital inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Table 22 Default settings - analog sensor inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Table 23 Default mapping of digital inputs to digital outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Table 24 Default mapping of analog inputs to digital outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Table 25 Default settings - digital outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Table 26 Supported modem settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Table 27 Default settings - modem . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Table 28 Country codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Table 29 Pager dialing results. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Table 30 Guidelines for dialing pagers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

Table 31 Battery alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Table 32 Service phone number dialing results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Table 33 Guidelines for dialing service phone number . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Table 34 Automatic / manual control - output points. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80

Table 35 Guide to Universal Monitor functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85

Table 36 Steps to set up a direct or remote connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86

Table 37 Universal Monitor - default settings for inputs and outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132

Table 38 Universal Monitor - other default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133

Table 39 Expansion Board - other default settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

Table 40 Expansion Board - default settings for inputs and outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134

1.0 INTRODUCTION

The Liebert Universal Monitor’s extensive capabilities can put it at the heart of your protective network. The Universal Monitor employs local alarming and remote paging services to keep personnel on-site and at remote locations apprised of the status of equipment.

The panel can interface with any device that closes an electrical contact or has a 4-20 mA signal. To improve process efficiency and troubleshooting, the panel tracks data in three types of logs: alarm, event and trend. The Universal Monitor has a local LCD interface and a remote dial-up interface.

Further, the Universal Monitor can report ambient conditions that might adversely affect the facility or equipment and also can report alarms and other events, as well as initiate responses to reduce or prevent damage.

When an alarm condition arises, the Universal Monitor displays alarm information and sounds an audible alarm; if configured, the panel also sends pager notifications and turns connected devices on or off. See 1.11 - Typical Sequence for a more detailed example.

1.1 Methods of Viewing and Configuring the Universal Monitor

The Universal Monitor features remote access through two interfaces that allow users to configure the panel, silence alarms, back up logs, and perform many other functions to keep a large or small operation running smoothly and safely.

• LCD—liquid crystal display on the front of the panel

• Service Terminal Interface—accessible via computer connected directly through an RS232 port or remotely through the Universal Monitor’s onboard modem

These interfaces permit easy access and configuration of the Universal Monitor, allowing users to view data, silence alarms and have full access to information stored in the panel, including logs of alarms and events.

One more interface—Liebert’s SiteScan Web enterprise monitoring system—is primarily for monitoring, though SiteScan also provides some configuration functions.

Introduction

1.2 Data Logs

The three types of data logs—alarm history, event history and trend data of analog sensor readings— can be viewed on the LCD on the front of the Universal Monitor and downloaded through onboard communications ports.

1.3 Optional Features

An optional Expansion Board, which can be purchased separately, allows you to connect an additional 16 digital inputs and eight digital outputs to the Universal Monitor.

An optional Transformer Module, available only in the large enclosure, converts 115VAC or 230VAC to 24VAC.

1.4 Available Alarms

The alarms available with the Universal Monitor are:

• Discrete input alarm (for each digital input)

•High setpoint

• Low setpoint

• Battery unplugged

• Low battery

• Loss of power

• Check battery

• Internal modem fault

Two additional alarms are available with the optional Expansion Board:

• Expansion board loss of communications

• Expansion board restore of communications

1.5 Outside Enclosure Overview

ESC

Universal Monitor

BAR CODE

SENS

The enclosure for the Universal Monitor’s controller board comes in two sizes:

•The large enclosure is designed to accommodate the Transformer Module and future compo- nents, in addition to the controller board.

•The small enclosure is built to hold the controller board only.

Both enclosures are 2-3/4" deep.

Both enclosures have a built-in liquid crystal display (LCD) and a key lock, as shown in the example below. The enclosures are made of metal to accommodate secure conduit fittings and protect components against environmental debris.

Figure 1 Small enclosure—external features

The enclosure has knockouts and access slots on top and bottom for cables and wires.

ESC

UNIVERSAL MONITOR

05-SEP-02 14:04:13

V5.100.0

PRESS =STATUS/SETUP

Introduction

LCD for configuration and operation

Key lock

Universal Monitor

The enclosure must be secured to a wall, either flush-mounted or recessed in the wall, as described in

2.0 - Installation - Main Board. Knockouts and access slots on the top and bottom allow easy connection of wires and cables (see 4.0 - Wiring and Connections - Main Board) with either mounting type.

Figure 2 Large enclosure—internal features

Transformer Module

Back of LCD

TB5: COMMON ALARM

(TERMINAL BLOCKS ROTATED IN VIEW)

NO C NC NO C NC

(BOTTOM)

(TOP)

LS1

TB7:

START

BAR CODE

LIEBERT

MODEM

J11: PHONE

PIN 3-TIP

PIN 4-RI"N"G

ENABLE

P11

AUDIBLE

R402

ALARM

R26

Q11

TOP

TB3: RELAY OUTPUTS

(BOTTOM) (BOTTOM)

(TOP)

(BOTTOM) (BOTTOM)

(TOP)

TB2: CONTACT

ASS REV

TB9: ANALOG GROUND

ALL CIRCUITS;

CLASS 2

INPUTS

1-2 TOP 3-4 BOTTOM

(TOP)

—

——

+ +

485

—

+—+

(BOTTOM)

—

Controller Board

On/Off switch for Transformer Module

Ground wire for LCD

Power receptacle

Knockouts and access slots (top and bottom)

1.6 Typical Configuration

BAR CODE

TB10: COMMS

Figure 3 shows an example of external devices connected to the Universal Monitor’s controller board. There may be up to eight digital output, eight digital input and four analog input devices connected. The optional Universal Monitor Expansion Board provides additional connections for eight output and sixteen digital input devices. Remote access is available via SiteScan Web and through the modem, which enables pager notifications and use of the Service Terminal Interface.

Figure 3 Typical Configuration

TB7:

START

24V INPUT

BATTERY

RS232

Phone

line

P23: BATTERY

VBATT

J11: PHONE

PIN 3-TIP PIN 4-RING

LCD CONTRAST

Universal Monitor

main board

BAR CODE

LIEBERT

TP1

GND

DIP

2345678

OFF

MODEM

OUTPUT1

DS56

OUTPUT2

DS54

OUTPUT3

DS63

OUTPUT4

DS61

OUTPUT5

DS60

OUTPUT6

DS62

OUTPUT7

DS55

OUTPUT8

DS57

CTRLLOCK

DS59

DS83

SENLOCK

DS58

CAN TX

CMN ALR

DS84

DS53

CAN RX

MOP F PROG 574 TX 574 RX 485 RX 485 TX

INPUT1 INPUT2 INPUT3 INPUT4

DS70

INPUT5

DS67

INPUT6

DS66

INPUT7

DS65

INPUT8

DS64

R334

C71

485

(TOP)

—

——

+ +

422

—

+—+

(BOTTOM)

—

(TERMINAL BLOCKS ROTATED IN VIEW)

NO C NC NO C NC

(TOP)

LS1

ENABLE

P11

AUDIBLE

Q11

1-2 TOP 3-4 BOTTOM

TB9: ANALOG GROUND

TB5: COMMON ALARM

TOP

PFM2

PFM5

ALL CIRCUITS:

(BOTTOM)

Introduction

Digital outputs

TB3: RELAY OUTPUTS

(BOTTOM)

(TOP)

(BOTTOM)

(TOP)

TB2: CONTACT

ASS REV

INPUTS

CLASS 2

Water pump

Third-party

system

(BMS,

security

office)

SiteScan Web

Expansion Board

(optional)

POWER INPUT

Multiflex 168AO

810-3065

EIA485 + (to UM-) 0V EIA485 - (to UM+)

DEFAULT SETTINGS FOR USE WITH UNIVERSAL MONITOR

V1 V3 V5 V7 V9 V11 V13 V15

S4 S3 S2 S1

OUT1

Digital inputs

Chiller

RELAY OUTPUTS

V2 V4 V6 V8 V10 V12 V14 V16

K2 K3 K4 K5 K6 K7 K8

OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

USE COPPER (CU) CONDUCTORS ONLY.

Fire alarm

Analog inputs

panel

Generator

Digital inputs

UPS

LT410

Digital outputs

Heat

rejection

unit

Exhaust

fan

LT460

1.7 Controller Board Overview

BAR CODE

TB10: COMMS

The Universal Monitor’s controller board has connectors for eight digital inputs, four analog inputs and eight digital outputs, as shown below. The board comes complete with light emitting diodes (LEDs) to display the status of monitored devices, a battery pack for short-term backup, communications ports, power connections and other features necessary to monitor and protect your operation.

LIEBERT

TP1

GND

2345678

OFF

MODEM

Q - SiteScan Web connector (EIA422)

C - EIA422 LEDs

DIP

(TOP)

(BOTTOM)

DS56

DS54 DS63

DS61 DS60 DS62 DS55 DS57

DS59

DS83

DS58

CAN TX

DS84

DS53

CAN RX

DS70 DS67 DS66 DS65 DS64

R334

485

—

——

+ +

422

+—+

—

D - Audible horn

TB5: COMMON ALARM

(TERMINAL BLOCKS ROTATED IN VIEW)

NO C NC NO C NC

(TOP)

LS1

ENABLE

P11

AUDIBLE

Q11

OUTPUT1 OUTPUT2 OUTPUT3 OUTPUT4 OUTPUT5 OUTPUT6 OUTPUT7 OUTPUT8 CTRLLOCK SENLOCK CMN ALR

MOP F PROG 574 TX 574 RX 485 RX 485 TX

INPUT1 INPUT2 INPUT3 INPUT4 INPUT5 INPUT6 INPUT7 INPUT8

C71

1-2 TOP 3-4 BOTTOM

TB9: ANALOG

—

GROUND

TOP

PFM2

PFM5

ALL CIRCUITS:

P - 12VDC/24VDC analog input jumper

E - Audible horn jumper

(BOTTOM)

TB3: RELAY OUTPUTS

(BOTTOM)

(TOP)

(BOTTOM)

(TOP)

TB2: CONTACT

ASS REV

INPUTS

CLASS 2

O - Analog input connectors

2.4: Connect Power to the Universal Monitor

2.4.3: Connecting the Battery Pack

9.9.4: Connect Battery

1.9: LED Indicators

N/A

4.0: Wiring and Connections Main Board

4.4: Connecting Common Alarm Outputs

9.4: Setup System - Setup Common Alarm

1.9: LED Indicators

9.11: Manual Output Ctrl

4.0: Wiring and Connections Main Board

4.2.2: Connecting Digital Outputs

7.6: View Output Status

9.7: Setup System - Setup Output

B - Battery pack

EE - Transformer

A - Power On/Off switch

Module

DD - 24VAC power connector

CC - Battery pack connector

BB - LCD contrast adjustment

AA - LCD connector

TB7: 24V INPUT

P23: BATTERY

START

BAR CODE

BATTERY

LCD CONTRAST

VBATT

Z - DIP switch 1

Y - Modem status LEDs

X - Modem

W - 24VAC connector

V - Power On/Off

J11: PHONE

PIN 3-TIP PIN 4-RING

switch

U - Power receptacle

T - Phone line connector

S - Serial interface connector

R - EIA485 connector

(RS232/EIA574)

Table 1 Controller board components

Item Description For more information, see:

A - Power On/Off switch

B - Battery pack

C - EIA422 LEDs

D - Audible horn Provides audible notification when an alarm occurs. N/A E - Audible horn

jumper

F - Common Alarm connectors

G - Digital output status LEDs

H - Manual Override Switch (outputs)

I - Digital output connectors

J - Status LEDs Indicates the operational status of the controller board. 1.9: LED Indicators

Power switch for the controller board. When switched off, the battery pack is disabled.

Provides battery backup during a power loss to maintain normal operation of the panel for a minimum of 10 minutes. The analog inputs will not be functional during a power loss (P/N 133455P1).

Indicates the connection status between the Universal Monitor and SiteScan Web.

Jumper to disable the audible horn (factory default is enabled).

The two common alarm connections are used to connect to a secondary warning device such as a horn, light or Building Management System (BMS). When an alarm is present, the contacts close and the external warning device is activated/notified. The common alarm contacts may be configured to be reset with the Silence button/command.

Each output has an LED to indicate its status: ON/OFF (energized/de-energized).

Placing the switch in the ON position will turn ON, or energize, all eight outputs simultaneously. This switch removes all automatic output control from the Universal Monitor.

Each of the eight output connections is a two-state point: ON/OFF (energized/de-energized).

An example of a field digital output point is a motor starter.

Introduction

F - Common Alarm connectors

G - Digital output status LEDs

H - Manual Override Switch (outputs)

I - Digital output connectors

J - Status LEDs

K - Digital output loss-of-power jumper

L - Digital input connectors

M - Digital input status LEDs

N - Analog ground connector

Table 1 Controller board components (continued)

Item Description For more information, see:

One of eight output jumpers. Each digital output has a jumper to set the fail-safe position of the output point when

K - Digital output lossof-power jumper

L - Digital input connectors

M - Digital input status LEDs

N - Analog ground connector

O - Analog input connectors

P - 12VDC/24VDC analog input jumper

Q - SiteScan Web connector (EIA422)

R - EIA485 connector

S - Serial interface connector (RS232/ EIA574)

T - Phone line connector

U - Power receptacle

(Transformer Module)

V - Power On/Off switch (Transformer

Module)

W - 24VAC connector (Transformer Module)

X - Modem On-board modem with 9600 baud rate.

Y - Modem status LEDs Indicates the operational status of the modem. 1.9: LED Indicators Z - DIP switch 1 DIP switch used for resetting password to default. 9.9.1: Change Password AA - LCD connector Connection for the LCD on the enclosure door. N/A BB - LCD contrast

adjustment CC - Battery pack

connector DD - 24VAC power

connector EE - Transformer

Module

power fails. The OFF position makes the contact Normally Open (factory default). The ON position makes the contact Normally Closed.

Note: The jumper position has no effect on the contact when the Universal Monitor has power.

Each of the eight input connections is a two-state point: ON/OFF (energized/de-energized). An example of a field digital input point is a leak detector.

Each input has an LED to indicate its status: ON/OFF (energized/de-energized).

Connection for an externally powered analog sensor that needs a reference to ground.

Each of the four input connections accepts a 4/20 mA signal. An example of a field analog input point is a temperature sensor.

One jumper to select voltage supplied for two-wire analog sensors. The jumper supplies all four analog input connectors with the same voltage. Factory default is 24VDC.

Connection to monitor Universal Monitor from Liebert’s SiteScan Web graphical monitoring package.

Connection to optional Expansion Board (purchased separately). Connect maximum of one Expansion Board.

Connection for laptop or video terminal. Used for configuration and monitoring using the Service Terminal Interface. Requires a null modem cable for connectivity (P/N 201258P1).

Connection for phone line. Used for pager notifications, service phone number, and configuration and monitoring using the Service Terminal Interface. Requires an RJ11 connector.

115VAC power receptacle to power laptop during configuration and diagnostics. Receptacle not available on 230VAC Transformer Module.

Power switch to turn power On/Off to both Transformer Module 24VAC connectors and power receptacle.

One of the two 24VAC connectors for power (the second is also on the right side of the Transformer Module near the top). Each connector is rated for 40VA.

Adjustment contrast for the LCD on the enclosure door. N/A

Connection for battery pack lead. 2.4.3: Connecting the Battery Pack

Power connection for the controller. Requires 24VAC.

Transformer Module used to convert 115VAC or 230VAC to 24VAC. Available only in the large enclosure.

4.2.3: Setting the Digital Output Jumpers

9.7.4: Configure Main Board Output for Loss of Power (“FailSafe”)

4.0: Wiring and Connections Main Board

4.2.1: Connecting Digital Inputs

7.5: View Input Status

9.3: Setup System - Setup Input

1.9: LED Indicators

4.3.2: Connecting the Analog Ground

4.0: Wiring and Connections Main Board

4.3: Connecting Analog Inputs

7.5: View Input Status

9.5: Setup System - Setup Sensor

4.3.1: Setting the 12VDC/24VDC Analog Power Jumper

4.0: Wiring and Connections Main Board

4.5: EIA422 SiteScan Web Connector

4.0: Wiring and Connections Main Board

5.3.1: Connect EIA485 Connectors to Main Board

4.6.1: RS232 Connector

A.2: Connecting to the Service

Terminal Interface

4.6.2: Phone Line Connector

9.8: Setup System - Setup Modem & Pagers

9.9.6: Setup Serv Ph Num - Enter Phone Number

A.2: Connecting to the Service

Terminal Interface

2.4.2: Termination and Mounting Large Enclosure

4.0: Wiring and Connections Main Board

2.4.2: Termination and Mounting Large Enclosure

4.0: Wiring and Connections Main Board

2.4.2: Termination and Mounting Large Enclosure

4.0: Wiring and Connections Main Board

9.8: Setup System - Setup Modem & Pagers

2.4: Connect Power to the Universal Monitor

2.4.2: Termination and Mounting Large Enclosure

Introduction

1.8 Optional Expansion Board Overview

The Universal Monitor Expansion Board, purchased separately, has connectors for 16 digital inputs and eight digital outputs, as shown below. The board has light emitting diodes (LEDs) to display the status of monitored output devices, communications ports for connection to the Universal Monitor, power connections and other features necessary to monitor and protect your operation.

J - 24VAC power connector

POWER INPUT

I - Power status LED (green)

H - EIA485 connector

G - EIA485 status LEDs (yellow & red)

F - General status LED (green)

EIA485 + (to UM-) 0V EIA485 - (to UM+)

DEFAULT SETTINGS FOR USE WITH UNIVERSAL MONITOR

Multiflex 168AO

810-3065

S4 S3 S2 S1

V2 V4 V6 V8 V10 V12 V14 V16

V1 V3 V5 V7 V9 V11 V13 V15

K2 K3 K4 K5 K6 K7 K8

OUT1

OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

RELAY OUTPUTS

E - Digital input connectors (16)

Introduction

USE COPPER (CU) CONDUCTORS ONLY.

A - Digital output connectors (8)

B - Digital output fuses (8)

C - Digital output DIP switch

D - Digital output status LEDs (8)

Table 2 Expansion board components

Item Description For more information, see:

A - Digital output connectors (8)

B - Digital output fuses (8)

C - Digital output DIP switch

D - Digital output status LEDs (8)

E - Digital input connectors (16)

F - General status LED (green)

G - EIA485 status LEDs (yellow & red)

H - EIA485 connector

I - Power status LED (green)

J - 24VAC power connector

Each of the eight output connections is a two-state point: ON/OFF (energized/de-energized).

An example of a field digital output point is a motor starter.

Bussmann GMA-2 or equivalent. 250V 2A Fast Blow fuse.

CAUTION: Fuses must be replaced with equivalent fuses. NOTE: Two (2) replacement fuses are shipped with

the Expansion Board enclosure.

DIP switch used for setting Normally Open / Normally Closed.

Each output has an LED to indicate its status: ON/OFF (energized/de-energized).

Each of the 16 input connections is a two-state point: ON/ OFF (energized/de-energized).

An example of a field digital input point is a leak detector.

Indicates the operational status of the Expansion Board.

Two LEDs indicate status of the EIA485 connection: ON/OFF (energized/de-energized).

Connection to the Universal Monitor.

Indicates the power status of the Expansion Board.

Power connection for the Expansion Board. Requires 24VAC.

5.0: Wiring and Connections Optional Expansion Board

4.2.2: Connecting Digital Outputs

7.6: View Output Status

9.7: Setup System - Setup Output

N/A

5.2.3: Setting the Digital Output DIP Switches

9.7.3: Set Expansion Board Output by DIP Switch

1.10: LED Indicators - Optional Expansion Board

5.0: Wiring and Connections Optional Expansion Board

4.2.1: Connecting Digital Inputs

7.5: View Input Status

9.3: Setup System - Setup Input

1.10: LED Indicators - Optional Expansion Board

5.3.1: Connect EIA485 Connectors to Main Board

9.10: Setup Exp Board - Optional Expansion Board

1.10: LED Indicators - Optional Expansion Board

3.4: Input Power Connections Optional Expansion Board

1.9 LED Indicators

BAR CODE

TB10: COMMS

The Universal Monitor’s controller board has LED indicators that show the status of inputs, outputs and the common alarm, as well as the modem and SiteScan Web connections.

TB5: COMMON ALARM

EIA422 SiteScan Web LEDs

TB7:

START

DS50

DS49

Modem LEDs

MODEM

DS77 TX DS76 RX DS74 DTR DS75 DCD

24V INPUT

P23: BATTERY

BATTERY

VBATT

J11: PHONE

PIN 3-TIP PIN 4-RING

BAR CODE

LIEBERT

LCD CONTRAST

TP1

GND

DIP

2345678

OFF

DS83

CAN TX

DS84

CAN RX

MODEM

485

(TOP)

422

(BOTTOM)

Table 3 LED indicators summary

LED Type LED Color Description

EIA422

LEDs

Modem

LEDs

Output

LEDs

Status

LEDs

Input LEDs

422 TX Green Universal Monitor is transmitting information over the EIA422 port 422 RX Green Universal Monitor is receiving information over the EIA422 port TX Green Universal Monitor is transmitting information via the modem RX Green Universal Monitor is receiving information via the modem DTR Green Indicates data terminal is ready (DTR)—lights up when modem is dialing DCD Green Indicates data carrier is detected (DCD)—lights up when modem has connection OUTPUT1 Green Indicates output is ON or energized OUTPUT2 Green Indicates output is ON or energized OUTPUT3 Green Indicates output is ON or energized OUTPUT4 Green Indicates output is ON or energized OUTPUT5 Green Indicates output is ON or energized OUTPUT6 Green Indicates output is ON or energized OUTPUT7 Green Indicates output is ON or energized OUTPUT8 Green Indicates output is ON or energized CTRLLOCK N/A Not used SENLOCK N/A Not used CMN ALR Green Indicates output is ON or energized

MOP Green

Indicates the microprocessor is operating properly (MOP)—must be on before

Universal Monitor will function FPROG Green Indicates firmware is being upgraded—lights up during upgrade process 574 TX or 232 TX Green Universal Monitor is transmitting information via the RS232 port 574 RX or 232 RX Green Universal Monitor is receiving information via the RS232 port

485 RX Green

485 TX Green

Universal Monitor is receiving information over the EIA485 port from the Expansion

Board

Universal Monitor is transmitting information over the EIA485 port to the Expansion

Board INPUT1 Red Indicates input is ON or energized INPUT2 Red Indicates input is ON or energized INPUT3 Red Indicates input is ON or energized INPUT4 Red Indicates input is ON or energized INPUT5 Red Indicates input is ON or energized INPUT6 Red Indicates input is ON or energized INPUT7 Red Indicates input is ON or energized INPUT8 Red Indicates input is ON or energized

(TERMINAL BLOCKS ROTATED IN VIEW)

NO C NC NO C NC

(TOP)

LS1

ENABLE

P11

AUDIBLE

Q11

OUTPUT1

DS56

OUTPUT2

DS54

OUTPUT3

DS63

OUTPUT4

DS61

OUTPUT5

DS60

OUTPUT6

DS62

OUTPUT7

DS55

OUTPUT8

DS57

CTRLLOCK

DS59

SENLOCK

DS58

CMN ALR

DS53

MOP F PROG

574 TX 574 RX 485 RX 485 TX

INPUT1 INPUT2 INPUT3 INPUT4

DS70

INPUT5

DS67

INPUT6

DS66

INPUT7

DS65

INPUT8

DS64

R334

C71

1-2 TOP 3-4 BOTTOM

—

——

+ +

TB9: ANALOG

—

+—+

GROUND

—

TOP

PFM2

PFM5

ALL CIRCUITS:

(BOTTOM)

TB3: RELAY OUTPUTS

(BOTTOM)

(TOP)

(BOTTOM)

(TOP)

TB2: CONTACT

ASS REV

INPUTS

CLASS 2

DS56

DS54 DS63

DS61 DS60 DS62 DS55 DS57

DS59 DS58

DS53

DS51 DS48

DS78 DS79

DS52

DS47

DS69

DS71

DS72 DS70 DS67 DS66 DS65 DS64

OUTPUT1 OUTPUT2 OUTPUT3 OUTPUT4 OUTPUT5 OUTPUT6 OUTPUT7 OUTPUT8

CTRLLOCK SENLOCK CMN ALR

MOP F PROG

574 TX 574 RX 485 RX 485 TX

INPUT1 INPUT2 INPUT3 INPUT4 INPUT5 INPUT6 INPUT7 INPUT8

Introduction

Output LEDs

Status LEDs

Input LEDs

1.10 LED Indicators - Optional Expansion Board

The optional Expansion Board, purchased separately, has LED indicators that show the status of inputs and outputs.

Power status LED

(D6 - green)

POWER INPUT

Multiflex 168AO

810-3065

Introduction

USE COPPER (CU) CONDUCTORS ONLY.

RELAY OUTPUTS

V2 V4 V6 V8 V10 V12 V14 V16

V1 V3 V5 V7 V9 V11 V13 V15

EIA485 + (to UM-) 0V EIA485 - (to UM+)

S4 S3 S2 S1

K2 K3 K4 K5 K6 K7 K8

OUT1

OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

EIA485 status LEDs

(D4 - yellow,

D5 - red)

Gen. Status

DEFAULT SETTINGS FOR USE WITH UNIVERSAL MONITOR

General status LED

(D3 - green)

OUT3OUT1 OUT2 OUT4 OUT5 OUT6 OUT7 OUT8

Digital output status LEDs (8)

Table 4 LED indicators summary

LED Type LED Color Description

Power status

LED

EIA485 status

LEDs

General status

LED

Digital output

status

LEDs

24VAC

Power (D6)

485 RX (D4) Yellow

485 TX (D5) Red

General

Status (D3)

Green 24VAC power is being supplied to Expansion Board

Expansion Board is receiving information over the EIA485 port from the Universal Monitor

Expansion Board is transmitting information over the EIA485 port to the Universal Monitor

Green

Blinks green once per second to indicate the board is powered and operational. If the light is off, the board has likely lost power.

OUT1 Red Indicates output is ON or energized

OUT2 Red Indicates output is ON or energized

OUT3 Red Indicates output is ON or energized

OUT4 Red Indicates output is ON or energized

OUT5 Red Indicates output is ON or energized

OUT6 Red Indicates output is ON or energized

OUT7 Red Indicates output is ON or energized

OUT8 Red Indicates output is ON or energized

K4K3K2K1 K5 K6 K7 K8

1.11 Typical Sequence

ESC

Figure 4 shows a typical sequence of how the Universal Monitor functions after detecting a change in a monitored unit or area. Many responses depend on configuration settings. This example shows what happens when an analog sensor input reaches a high setpoint—assuming the input is defined as alarmable and is set up to trigger a response in an output—and when the condition returns to normal.

Figure 4 Example of typical sequence: Analog input reaches high setpoint

RESPONSES TO AN ALARM RETURN-TO-NORMAL SEQUENCE

Introduction

ALARM CONDITION DETECTED

The temperature in a monitored analog input reaches its high setpoint.

RETURN TO NORMAL

The temperature in the monitored analog input returns to a normal range (below the high setpoint).

The alarm is cleared

The horn sounds (audible horn on

the controller board—silence horn by pressing any key on the LCD keypad)

(automatically if Unlatched; must be cleared manually if Latched)

The horn stops sounding

(if user hasn’t silenced it)

UNIVERSAL MONITOR 05-SEP-02 14:04:13

V5.100.0

PRESS =STATUS/SETUP

ESC

The LCD flashes

(except during setup)

UNIVERSAL MONITOR

05-SEP-02 14:04:13

V5.100.0

PRESS =STATUS/SETUP

ESC

Pager numbers are dialed

(up to four configured pagers)

Service number is dialed

The LCD stops flashing

Pager numbers & service number are dialed

Return-to-normal message sent

(if configured)

A fan is turned on

(if the fan is connected to an output

When the alarm is cleared, the fan shuts down

set up to respond to this input)

SENSOR_2 80.0 DEG HIGH SETPOINT ALARM 29-AUG-02 09:29:10

SENSOR_2 80.0 DEG HIGH SETPOINT ALARM

OUTPUT08 ON CONTACT OPEN 29-AUG-02 09:29:12

Entry in Alarm Log

Shows reading ( condition (

80.0 DEG) &

HIGH SETPOINT ALARM)

Entry in Active Alarm Log

Entry in Event Log

Fan output on

SENSOR_2 79.0 DEG RETURN TO NORMAL 29-AUG-02 09:42:11

OUTPUT08 OFF CONTACT CLOSED 05-MAY-02 09:42:12

Entry in Alarm Log

Shows reading ( condition (

79.0 DEG) &

RETURN TO NORMAL)

Entry in Event Log

Fan output off

2.0 INSTALLATION - MAIN BOARD

This section provides instructions for installing, mounting and connecting power to the Universal Monitor. For information on the optional Expansion Board, see 3.0 - Installation - Optional Expan- sion Board.

2.1 Installation Considerations

The Universal Monitor must be installed indoors and may be mounted on the surface of a wall or flush-mounted, depending on the user’s application, the location of equipment and sensors to be monitored and the type of wall the unit will be mounted on.

The Universal Monitor should be mounted where it can be easily accessed. On-site personnel would access the unit through the LCD on its front cover, service terminal connected to the RS232 port or through SiteScan. For off-site monitoring, the Universal Monitor should be placed near communications means such as a telephone line connection that would permit remote access.

In addition to the communications connections, the site also must have electrical service and must permit connecting the unit’s eight digital inputs, eight digital outputs and four analog inputs.

The wall material must be capable of supporting the weight of the Universal Monitor: see 10.0 -

Specifications.

NOTE

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Installation - Main Board

2.1.1 Unpacking and Preliminary Inspection

• Before unpacking the Universal Monitor, inspect the shipping carton for damage or signs of mishandling, such as gashes or holes in the carton or severely flattened corners.

• Open the shipping crates carefully. Use care to avoid puncturing the container with sharp objects that might damage the contents.

• Inspect the Universal Monitor and all included components for damage.

• If any damage from shipping or mishandling is observed, immediately file a damage claim with the shipping agency and forward a copy to:

Liebert Corporation 1050 Dearborn Drive P.O. Box 29186 Columbus, OH 43229

Packing Contents

Table 5 Packing manifest - Universal Monitor main board

Standard Components

• Universal Monitor - large or small enclosure

• User Manual

• Keys (2) to panel door lock

• Backup Battery - installed in unit (not connected or charged)

• RS232 Configuration Cable

2.2 Surface-Mounting the Universal Monitor

NOTE

Removing the conduit knockouts before mounting the Universal Monitor on the wall will ease installation and prevent strain on the mounting hardware and wall. It is imperative to remove the knockouts if the unit is to be flush-mounted.

After determining where to place the unit, check to ensure that you have all the hardware required to install the panel on the surface of a wall. Obtain the needed tools and material.

Required tools

• Electric drill (if surface is too hard to drive screws without pilot holes)

• Screwdriver

• Marker to denote layout of holes

• Four screws, each #10

2.2.1 Mounting the Panel

CAUTION

Check building plans and other relevant documents to determine whether mounting the Universal Monitor at the selected location might cause cutting or otherwise damaging electrical or communication wiring or pipes.

1. Mark the wall for mounting holes, using the back of the unit as a template (see Figure 5).

2. Drill holes, if required, to install the four #10 screws that will secure the Universal Monitor to the wall. Clean up the debris.

3. If the wall material is not strong enough to hold the screws securely, use wall anchors.

4. Install the top two screws—the screw heads must be small enough to slip through the larger, bottom portion of the pear-shaped mounting slot in the Universal Monitor (see inset in Figure 5). The screws must also be large enough to extend over the edges of the top of the mounting slot.

5. Hang the Universal Monitor on the screws, letting the panel slip down until the screws are in the smaller, upper portion of the slot.

6. Tighten the screws until they are snug.

7. Insert the remaining two screws in the bottom holes on the back of the panel and tighten.

Installation - Main Board

Figure 5 Mounting Dimensions

SMALL ENCLOSURE

12.5"

(317.5mm)

0.213"

(5.4mm)

Universal Monitor

back plate

0.375"

(9.6mm)

Mounting Slot

0.213" (5.4mm)

Bottom hole diameter

10"

(254mm)

LARGE ENCLOSURE

12"

(304.8mm)

0.213"

(5.4mm)

16"

(406.4mm)

Universal Monitor

back plate

0.375"

(9.6mm)

Mounting Slot

0.213" (5.4mm)

Bottom hole diameter

2.3 Flush-Mounting the Universal Monitor

NOTE

The rectangular access doors on the top and bottom of the Universal Monitor must be reversed so they slide the opposite direction. Leaving the doors as shipped from the factory prevents them from being opened when the panel is flush mounted in a wall.

The Universal Monitor may be flush-mounted according to company practices—either with screws through the sides of the panel into wall supports or with hanging hardware that attaches to the back of the panel. After determining how and where to place the unit, check to ensure that you have all the hardware required to install the panel in the wall. Obtain the needed tools.

Required tools

•Saw

• Electric drill

• Screwdriver

• Marker to denote layout of the hole to accommodate the Universal Monitor

• Trim ring and associated hardware

• Mounting hardware

Installation - Main Board

2.3.1 Mounting the Panel

CAUTION

1. Mark the wall for the cutout to accommodate the panel, using the back of the unit as a template.

2. Drill a pilot hole for the saw blade, if required.

3. Use the saw to cut out the marked section of the wall (if not new construction).

4. Rest the Universal Monitor in the wall and mark where mounting screws will be inserted into the wall studs or other support member.

5. Remove the panel and drill the holes for the mounting screws or wall anchors. Clean up the debris.

6. Reverse the slide direction of the rectangular access doors on the top and bottom of the Universal Monitor. Leaving the doors as shipped from the factory prevents them from being opened when the panel is flush mounted in a wall.

7. Attach any field-supplied mounting hardware.

8. Reinsert the assembly into the wall.

9. Insert and tighten the screws or wall anchors.

2.4 Connect Power to the Universal Monitor

The Universal Monitor requires 24VAC for proper operation. Liebert recommends using the optional Transformer Module manufactured by Liebert or another UL-approved Class 2 power unit to obtain proper voltage. If the power unit is not a Class 2 circuit, it must be protected with an IEC 5 x 20mm time lag 2A fuse. For information, consult your local dealer, Liebert representative or the Liebert Worldwide Support Group.

WARNING

Check that power is removed from wires prior to installation.

CAUTION

The Universal Monitor is designed for use on properly grounded (earthed) 24VAC power, 50Hz or 60Hz. The ground wire for the power lead must be wired to the earth ground terminal (stud located next to the 24VAC terminal block).

This equipment is intended to be installed by a qualified and certified electrician who must review and approve customer supplied wiring and circuit breakers, verify correct input and grounded (earthed) connections to ensure compliance with technical standards and national and local electrical codes.

WARNING

Be sure that the Power On/Off switch is set to OFF before installing any wiring to this unit. The switch is in the top left corner of the unit, just below the battery pack.

Installation - Main Board

2.4.1 Input Power Connections - Small Enclosure

To connect electrical power:

1. Run conduit and electrical wiring from building to the Universal Monitor.

2. Use copper wires only; proper wiring to use for 24VAC power is 18-22 AWG stranded and shielded (18 AWG is recommended—see Table 7). Strip wires 1/2".

Figure 6 Electrical connections to panel

External wiring through knockout

Ground wire (black)

Earth ground terminal

Power On/Off switch

24VAC wiring (red & white)

3. Secure the incoming electrical service wires to the Universal Monitor’s 24VAC input by sliding the wires into TB7, the 24VAC input terminal block. There is no polarity requirement when connecting to TB7. The ground wire must be connected to the earth ground terminal located on the side of the panel (see Figure 6).

24VAC input connector

2.4.2 Termination and Mounting - Large Enclosure

CAUTION

The 115VAC/230VAC Transformer Module must be connected to a branch circuit with 15A branch circuit protection.

This equipment is intended to be installed by a qualified and certified electrician who must review and approve customer supplied wiring and circuit breakers, verify correct input and grounded connections to ensure compliance with the technical standards and national and local electrical codes.

The Transformer Module shall be used only as indicated by the manufacturer.

WARNING

Be sure that the Power On/Off switch is set to OFF before installing any wiring to this unit. The switch is at the bottom of the unit.

Input Power Connections

To connect electrical power to the Transformer Module:

1. Install electrical wiring from utility power to the Transformer Module.

2. Use copper wires only; proper wiring to use for power is 14/2 AWG copper wire with ground.

3. For the TM230 only: strip wires 3/8" (9.6mm). Note: For the TM115, wires are pre-stripped 0.4" (10.2mm) at the factory.

4. Connect the wiring as follows:

Installation - Main Board

TM115 TM230 Connection Type

White wire Neutral (L2) Neutral

Black wire Line (L1) Power (Line)

Green wire Ground lead Ground

5. Secure the incoming electrical service wires to the TM115 input wires with wire nuts as shown in Figure 7 or to the TM230 connectors as shown in Figure 8.

24 VAC Output Power Connections

To connect to the 24VAC outputs:

1. Install electrical wiring from device requiring 24VAC power to the Transformer Module.

2. Use copper wire only; proper wiring to use for power is 18, 20 or 22 AWG copper wire. Strip wire 1/4".

3. There are two 24 VAC output connectors (TB1 and TB2). Terminate wires to the connector as shown in Figures 7 and 8. TB1 and TB2 are NOT polarity sensitive.

4. Secure the wires to the connector.

Figure 7 Power wiring to TM115 Figure 8 Power wiring to TM230

TM115

Wire nuts connecting electrical wiring

Knockout for external wiring

Ground

TM230

Knockout for external wiring

Ground

24VAC output (TB1)

Neutral (L2)

Line (L1)

24VAC output (TB1)

Troubleshooting - Transformer Module

A common problem and possible solution are shown in the table below. For further information or if you have other problems with the unit, consult your local dealer, Liebert representative or the Liebert Worldwide Support Group.

Problem Possible Solution Replacement Fuse Part Numbers

24VAC power not available from TB1 or TB2

Check fuse for respective output (TB1 or TB2).

2.4.3 Connecting the Battery Pack

After connecting AC power to the Universal Monitor, you may connect the panel’s backup battery (factory-supplied) to the jumpers so it will begin charging when electrical power to the Universal Monitor is switched on.

NOTE

If the battery is not hooked up before the Universal Monitor is switched on, it will trigger an alarm.

To connect the battery pack, insert the battery leads into the jumpers as shown at right. (To disconnect the battery pack, remove the battery leads from the jumpers.)

Installation - Main Board

• LITTLEFUSE 218002

• BUSSMANN GDC-2A

Battery pack

Obtaining a Replacement Battery Pack

To obtain a replacement battery pack, contact your local dealer or Liebert representative. The Liebert part number is 133455P1.

WARNING

To prevent the risk of fire or explosion, replace only with 7.2 V rechargeable NiCad battery pack.

CAUTION

Dispose of the battery properly by sending it back to Liebert Corporation or an approved battery recycling facility.

Battery pack connector

3.0 INSTALLATION - OPTIONAL EXPANSION BOARD

This section provides instructions for installing, mounting and connecting power to the optional Expansion Board. The Expansion Board enclosure is identical to the Universal Monitor’s small enclosure.

3.1 Installation Considerations

The optional Expansion Board must be installed indoors and may be mounted on the surface of a wall or flush-mounted, depending on the user’s application, the location of equipment and sensors to be monitored and the type of wall the unit will be mounted on.

The Expansion Board may be placed up to 3000 ft. (914m) from the Universal Monitor and should be mounted where it can be easily accessed. The site must have electrical service and allow for connecting 16 digital inputs and eight digital outputs.

The wall material must be capable of supporting the weight of the Expansion Board: see 10.2 -

Optional Expansion Board Specifications.

NOTE

Installation - Optional Expansion Board

3.1.1 Unpacking and Preliminary Inspection

• Before unpacking the optional Expansion Board, inspect the shipping carton for damage or signs of mishandling, such as gashes or holes in the carton or severely flattened corners.

• Open the shipping crates carefully. Use care to avoid puncturing the container with sharp objects that might damage the contents.

• Inspect the Expansion Board and all included components for damage.

• If any damage from shipping or mishandling is observed, immediately file a damage claim with the shipping agency and forward a copy to:

Liebert Corporation 1050 Dearborn Drive P.O. Box 29186 Columbus, OH 43229

Packing Contents

Table 6 Packing manifest - optional Expansion Board

Standard Components

• Expansion Board - small enclosure

• User Manual

• Keys (2) to panel door lock

• Two (2) spare fuses for output relays

3.2 Surface-Mounting the Optional Expansion Board

NOTE

Removing the conduit knockouts before mounting the optional Expansion Board on the wall will ease installation and prevent strain on the mounting hardware and wall. It is imperative to remove the knockouts if the unit is to be flush-mounted.

After determining where to place the optional Expansion Board, check to ensure that you have all the hardware required to install the panel on the surface of a wall. Obtain the needed tools and material.

Required tools

• Electric drill (if surface is too hard to drive screws without pilot holes)

• Screwdriver

• Marker to denote layout of holes

• Four screws, each #10

3.2.1 Mounting the Panel

CAUTION

Check building plans and other relevant documents to determine whether mounting the optional Expansion Board at the selected location might cause cutting or otherwise damaging electrical or communication wiring or pipes.

Installation - Optional Expansion Board

1. Mark the wall for mounting holes, using the back of the unit as a template (see Figure 5).

2. Drill holes, if required, to install the four #10 screws that will secure the optional Expansion Board to the wall. Clean up the debris.

3. If the wall material is not strong enough to hold the screws securely, use wall anchors.

4. Install the top two screws—the screw heads must be small enough to slip through the larger, bottom portion of the pear-shaped mounting slot in the Expansion Board (see inset in Figure 5). The screws must also be large enough to extend over the edges of the top of the mounting slot.

5. Hang the Expansion Board on the screws, letting the panel slip down until the screws are in the smaller, upper portion of the slot.

6. Tighten the screws until they are snug.

7. Insert the remaining two screws in the bottom holes on the back of the panel and tighten.

Figure 9 Mounting Dimensions - optional Expansion Board

SMALL ENCLOSURE

12.5"

(317.5mm)

0.213"

(5.4mm)

Expansion Board

back plate

10"

(254mm)

0.375"

(9.6mm)

Mounting Slot

0.213" (5.4mm)

Bottom hole diameter

3.3 Flush-Mounting the Optional Expansion Board

NOTE

The rectangular access doors on the top and bottom of the Expansion Board must be reversed so they slide the opposite direction. Leaving the doors as shipped from the factory prevents them from being opened when the panel is flush mounted in a wall.

The optional Expansion Board may be flush-mounted according to company practices—either with screws through the sides of the panel into wall supports or with hanging hardware that attaches to the back of the panel. After determining how and where to place the unit, check to ensure that you have all the hardware required to install the panel in the wall. Obtain the needed tools.

Required tools

•Saw

• Electric drill

• Screwdriver

• Marker to denote layout of the hole to accommodate the optional Expansion Board

• Trim ring and associated hardware

• Mounting hardware

Installation - Optional Expansion Board

3.3.1 Mounting the Panel

CAUTION

1. Mark the wall for the cutout to accommodate the panel, using the back of the unit as a template.

2. Drill a pilot hole for the saw blade, if required.

3. Use the saw to cut out the marked section of the wall (if not new construction).

4. Rest the optional Expansion Board in the wall and mark where mounting screws will be inserted into the wall studs or other support member.

5. Remove the panel and drill the holes for the mounting screws or wall anchors. Clean up the debris.

6. Reverse the slide direction of the rectangular access doors on the top and bottom of the Expansion Board. Leaving the doors as shipped from the factory prevents them from being opened when the panel is flush mounted in a wall.

7. Attach any field-supplied mounting hardware.

8. Reinsert the assembly into the wall.

9. Insert and tighten the screws or wall anchors.

3.4 Input Power Connections - Optional Expansion Board

The optional Expansion Board requires 24VAC for proper operation. Liebert recommends using the optional Transformer Module manufactured by Liebert or another UL-approved Class 2 power unit to obtain proper voltage. If the power unit is not a Class 2 circuit, it must be protected with an IEC 5 x 20mm time lag 2A fuse. For information, consult your local dealer, Liebert representative or the Liebert Worldwide Support Group.

CAUTION

The Expansion Board is designed for use on properly grounded (earthed) 24VAC Class 2 power, 50Hz or 60Hz. The ground wire for the power lead must be wired to the earth ground terminal (stud located next to the 24VAC terminal block). This equipment is intended to be installed by a qualified and certified electrician who must review and approve customersupplied wiring and circuit breakers, verify correct input and grounded (earthed) connections to ensure compliance with technical standards and national and local electrical codes.

WARNING

“RISK OF ELECTRIC SHOCK” - More than one disconnect switch may be required to de-energize the equipment before servicing.

WARNING

Hazardous voltage may be present.

To connect electrical power:

1. Run 24VAC electrical power from the TB2 (or TB1) connector of the Transformer Module, as shown in Figure 10, or another 24V source to the Expansion Board in accordance with local electrical codes.

2. Use copper wires only; proper wiring to use for power is 18-22 AWG stranded and shielded (18 AWG is recommended—see Table 9). Strip wires 1/2".

Installation - Optional Expansion Board

Figure 10 Electrical connections to panel

TRANSFORMER MODULE (TM115 shown)

24VAC wiring (red & white)

24VAC output (TB2 shown; use either TB1 or TB2)

3. Secure the incoming electrical service wires to the Expansion Board’s 24VAC input by sliding the wires into AC1 and AC2, the 24VAC input connectors, as shown in Figure 10. There is no polarity requirement when connecting to these connectors.

NOTE: The ground wire connection to the 0V connector is pre-wired at the factory.

OPTIONAL EXPANSION BOARD

Ground wire (pre-wired)

EIA485 + (to UM-)

EIA485 - (to UM+)

POWER INPUT

Ground wire connector (0V)

24VAC input connectors (AC1 & AC2)

Wiring and Connections - Main Board

4.0 WIRING AND CONNECTIONS - MAIN BOARD

CAUTION

Switch OFF electric power to the Universal Monitor before installing any wiring to the unit or changing input or output connections. The Power On/Off switch is in the top left corner of the unit, just below the battery pack.

4.1 Wiring Specifications

Input and output connections to the Universal Monitor may be made in any order—it is not necessary, for example, to make all input connections before making any output connections. Use copper conductors only for all wiring.

Table 7 Wiring specifications - main board

Connection Supported Wire Type Maximum Wire Length Rating

Digital

Input

Digital

Output

Analog Input

2-Wire

Transducer

Analog Input

4-Wire

Transducer

Common

Alarm

Output

Communication

RS232

Communication

EIA422

SiteScan

Communication

EIA485

Phone/Modem

Line

24VAC Power

Connection

(TB7)

Power Connections (Transformer Module)

115VAC

230VAC

* Recommended

18-22 AWG Stranded & Unshielded

18 AWG* (recommended)

Non Plenum - Belden 9740 Plenum - Belden 89740

18-22 AWG Stranded & Unshielded

18 AWG* (recommended)

Non Plenum - Belden 9740 Plenum - Belden 89740

18-22 AWG Stranded & Unshielded

18 AWG* (recommended)

Non Plenum - Belden 9740 Plenum - Belden 89740

18-22 AWG Stranded & Unshielded

18 AWG* (recommended)

Non Plenum - Belden 8489 Plenum - Belden 88489

18-22 AWG Stranded & Unshielded

18 AWG* (recommended)

Non Plenum - Belden 9740 Plenum - Belden 89740

Null Modem Cable 50 ft. (15m) N/A

18-22 AWG Stranded & Shielded

22 AWG* (recommended)

Non Plenum - Belden 9461 Plenum - Belden 88761

18-22 AWG Stranded & Shielded

22 AWG* (recommended)

Non Plenum - Belden 9461 Plenum - Belden 88761

4 Wire (Pins 3 & 4) RJ11 Connector

18-22 AWG Stranded & Shielded

18 AWG* (recommended)

Non Plenum - Belden 8770 Plenum - Belden 88770

14 AWG Stranded & Unshielded Non Plenum - Belden 5101UE

18 AWG*

(recommended)

@3A 50 ft. (15m) @2A 100 ft. (30m) @1A 200 ft. (60m)

18 AWG*

(recommended)

@3A 50 ft. (15m) @2A 100 ft. (30m) @1A 200 ft. (60m)

750 ft. (225m)

20 AWG 22 AWG

@3A 40 ft. (12m) @2A 60 ft. (18m) @1A 100 ft. (30m)

750 ft. (225m)

20 AWG 22 AWG

@3A 40 ft. (12m) @2A 60 ft. (18m) @1A 100 ft. (30m)

1000 ft. (300m) N/A

3000 ft. (900m) N/A

N/A N/A

150 ft. (45m)

@3A 25 ft. (7m) @2A 35 ft. (10m) @1A 75 ft. (23m)

Dry Contact

4-20 mA Signal

Input Selectable

Power Source

(12/24VDC)

4-20 mA Signal

Input Selectable

Power Source

(12/24VDC)

(24VDC,

10 mA)

24VAC

@3A

24VAC

@3A

24VAC @1.3A

115VAC

@4A

230VAC

@0.5A

4.2 Connecting Digital Inputs and Digital Outputs

OFF ON

OFF

The digital inputs and digital outputs are found on the lower right side of the Universal Monitor’s printed wiring assembly board. There are two terminal blocks for the inputs—one green, the other black. There are two terminal blocks for the outputs—one green, the other black.

To determine the proper wire size, see Table 7 - Wiring specifications - main board.

NOTE

Each terminal block is a removable, two-part assembly to permit easier connection of more than one input at a time. If making multiple connections, grasp the upper portion of a block and pull firmly to the right until the assembly pulls apart.

After making the connections, push the removed piece back into the portion attached to the printed wiring assembly until the terminal block pieces lock together.

4.2.1 Connecting Digital Inputs

To connect an input:

1. Turn OFF electrical power to the Universal Monitor.

2. If necessary, remove a conduit knockout to permit wire entry into the Universal Monitor enclosure.

3. Bring the wire(s) into the Universal Monitor enclosure through a conduit knockout or access slot.

4. Loosen the appropriate screw and slip the stripped end of the wire into the terminal block.

5. Tighten the screw until it holds the wire snugly.

4.2.2 Connecting Digital Outputs

To connect an output:

1. Turn OFF electrical power to the Universal Monitor.

2. If necessary, remove a conduit knockout to permit wire entry into the Universal Monitor enclosure.

3. Bring the wire(s) into the Universal Monitor enclosure through a conduit knockout or access slot.

4. Loosen the appropriate screw and slip the stripped end of the wire into the terminal block.

5. Tighten the screw until it holds the wire snugly.

PFM2

PFM5

Wiring and Connections - Main Board

TB3: RELAY OUTPUTS

(TOP)

TB2: CONTACT

ASS REV

INPUTS

(BOTTOM)

OUTPUT TERMINAL BLOCKS Note numbering of outputs begins at the bottom and

proceeds up; numbering

keys are shown at right

Numbering keys

INPUT TERMINAL BLOCKS Note numbering of inputs begins at the bottom and proceeds up; numbering keys are shown at right

CAUTION

To reduce the risk of fire or electric shock, do not interconnect the outputs of different Class 2 circuits.

4.2.3 Setting the Digital Output Jumpers

Each digital output has an associated jumper to define its operation when power is interrupted and there is no battery backup to the board. This puts the Universal Monitor in a fail-safe mode and ensures proper functioning when the board has no power or battery backup.

Wiring and Connections - Main Board

The Universal Monitor comes from the factory with all digital output jumpers in the OFF position (normally open). The jumper setting for each digital output can be changed to ON (normally closed). The settings are shown in Table 8.

Table 8 Digital output jumper settings

Setting

(power loss & no battery backup)

OFF Normally open

ON Normally closed

Output status

To change the output jumper setting:

1. Find the respective black output jumper on the circuit board, as shown above.

2. Decide whether your configuration requires the jumper to be OFF or ON.

3. Set the jumper as needed:

• Set the jumper to OFF by placing the black jumper on the middle and top pins.

• Set the jumper to ON by placing the black jumper on the middle and bottom pins.

Digital output jumpers

TB3: RELAY OUTPUTS

(BOTTOM)

(TOP)

REV

(TOP)

(BOTTOM)

OFF

PFM2

OFF ON

PFM5

4.3 Connecting Analog Inputs

The analog input connector blocks are at the bottom center of the Universal Monitor printed circuit board. The blocks are two-part assemblies to permit easier connections. To determine the proper wire size, see Table 7 - Wiring specifications - main board.

To connect an input:

1. Turn OFF electrical power to the Universal Monitor.

2. If necessary, remove a conduit knockout to permit wire entry into the Universal Monitor enclosure.

3. Bring the wire(s) into the Universal Monitor enclosure through a conduit knockout or access slot.

4. Loosen the appropriate screw and slip the stripped end of the wire into the terminal block.

5. Tighten the screw until it holds the wire snugly.

Analog inputs

: COMMS

(TOP)

(BOTTOM)

485

422

Analog ground

1-2 TOP 3-4 BOTTOM

—

——

+ +

—

+—+

—

TB9: ANALOG GROUND

4.3.1 Setting the 12VDC/24VDC Analog Power Jumper

The analog power jumper sets the common voltage that is applied to all of the analog input connections. The jumper permits the user to modify the voltage supplied to the sensors, according to the power requirements.

The factory default position is 24VDC; it may be changed to 12VDC.

To change the analog power jumper setting:

1. Find the black analog jumper on the circuit board, as shown at right. The jumper is at the bottom of the board near the middle (see 1.7 - Controller Board Overview).

2. Decide whether your configuration requires the jumper to be 24VDC or 12VDC.

3. Set the jumper as needed:

• Set the jumper to the 24VDC position by placing the black jumper on the middle and right pins.

• Set the jumper to the 12VDC position by placing the black jumper on the middle and left pins.

Wiring and Connections - Main Board

Analog power jumper

1-2 TOP 3-4 BOTTOM

485

OMMS

(TOP)

—

(BOTTOM)

422

—

——

+ +

+—+

TB9: ANAL

—

GROUND

4.3.2 Connecting the Analog Ground

The Universal Monitor features an analog ground connection for four-wire sensors that have an external power source. Such a four-wire sensor requires a reference to ground because they get power from an external power source.

A two-wire transducer, which does not have an external power source, does not need to be connected to the analog ground.

The analog ground connector has two terminals, each of which can accommodate two wires. This is adequate to connect four sensors that require a reference to ground because they get power from an external power source.

Connect the analog ground to an external fourwire sensor as shown in the illustration at right.

TB10: COMMS

Four-wire transducer

Sensor with external power

(TOP)

(BOTTOM)

4/20mA

Output

Analog input

—

24V Input

Analog ground

1-2 TOP 3-4 BOTTOM

TB9: ANALOG GROUND

—

24V from external power source

4.4 Connecting Common Alarm Outputs

SENS

TB10: COMMS

Wiring and Connections - Main Board

The common alarm relay, found in the top right corner of the Universal Monitor, permits the user to connect auxiliary notification equipment, such as lights, horns and sirens, to the Universal Monitor. To determine the proper wire size, see Table 7 - Wiring specifications - main board.

There are two connectors for the common alarm output. However, the connectors are not individual relay outputs. The connectors should be treated as a double-pole, double-throw (DPDT) relay.

The common alarm relay is energized whenever an alarm occurs.

To connect an output:

1. Turn OFF electrical power to the Universal Monitor.

2. If necessary, remove a conduit knockout to permit wire entry into the Universal Monitor enclosure.

3. Bring the wire(s) into the Universal Monitor enclosure through a conduit knockout or access slot.

4. Loosen the appropriate screw and slip the stripped end of the wire into the terminal block.

5. Tighten the screw until it holds the wire snugly.

4.5 EIA422 SiteScan Web Connector

The Universal Monitor will interface with Liebert’s SiteScan Web enterprise monitoring system. SiteScan can be used to monitor analog and digital equipment from a host computer and also to perform some configuration.

TB5: COMMON ALARM

(TERMINAL BLOCKS ROTATED IN VIEW)

NO C NC NO C NC

(TOP)

ENABLE

P11

AUDIBLE

R402

R26

Q11

Common alarm outputs

N ALARM

(BOTTOM)

TOP

To connect the SiteScan host computer to the Universal Monitor:

1. Turn OFF electrical power to the Universal Monitor.

2. If necessary, remove a conduit knockout to permit wire entry into the Universal Monitor enclosure.

3. Bring the wire(s) into the Universal Monitor enclosure through a conduit knockout or access slot.

4. Loosen the appropriate screw and slip the stripped end of the wire into the terminal block.

5. Tighten the screw until it holds the wire snugly.

4.6 Communications Connections

The Universal Monitor’s Service Terminal Interface offers full configuration and monitoring capability via the RS232 port and the phone line connector (see A.2 - Connecting to the Service Terminal Interface). The phone line connector is also used for pager notifications and service phone number options.

4.6.1 RS232 Connector

The RS232 port requires a null modem cable. Connect one end of the cable to the Universal Monitor’s RS232 port, as shown at right, and the other end to the COM1 port of a laptop computer or video terminal.

4.6.2 Phone Line Connector

TB10: COMM

EIA422 SiteScan Web connector

Serial interface connector (RS232/EIA574)

MODEM

RJ11: PHONE

PIN 3-TIP PIN 4-RING

(TOP)

(BOTTOM)

—

422

—

(TOP)

(BOTTOM)

The Phone Line Connector requires an RJ11 connector. Connect one end of the connector to the Universal Monitor’s phone line connector, shown at right, and the other end to a

Phone line connector

telephone wall jack.

Wiring and Connections - Optional Expansion Board

5.0 WIRING AND CONNECTIONS - OPTIONAL EXPANSION BOARD

CAUTION

Remove all power before installing any wiring to the Expansion Board or changing input or output connections.

WARNING

“RISK OF ELECTRIC SHOCK” - More than one disconnect switch may be required to de-energize the equipment before servicing.

5.1 Wiring Specifications

Input and output connections to the optional Expansion Board may be made in any order—it is not necessary, for example, to make all input connections before making any output connections. Use copper conductors only for all wiring.

Table 9 Wiring specifications - optional Expansion Board

Connection Supported Wire Type Maximum Wire Length Rating

Digital

Input

Digital

Output

Communication

EIA485

24VAC Power

Connection

(TB1)

* Recommended

18-22 AWG Stranded & Unshielded

18 AWG* (recommended)

Non Plenum - Belden 9740 Plenum - Belden 89740

18-22 AWG Stranded & Unshielded

18 AWG* (recommended)

Non Plenum - Belden 9740 Plenum - Belden 89740

18-22 AWG Stranded & Shielded

22 AWG* (recommended)

Non Plenum - Belden 9461 Plenum - Belden 88761

18-22 AWG Stranded & Shielded

18 AWG* (recommended)

Non Plenum - Belden 8770 Plenum - Belden 88770

18 AWG*

(recommended)

@3A 50 ft. (15m) @2A 100 ft. (30m) @1A 200 ft. (60m)

750 ft. (225m)

20 AWG 22 AWG

@3A 40 ft. (12m) @2A 60 ft. (18m) @1A 100 ft. (30m)

3000 ft. (900m) N/A

150 ft. (45m)

@3A 25 ft. (7m) @2A 35 ft. (10m) @1A 75 ft. (23m)

Dry Contact

(24VDC,

10 mA)

240VAC,

2A max.

24VAC @0.6A

5.2 Connecting Inputs and Outputs

The Universal Monitor’s optional Expansion Board permits the addition of 16 input and eight output devices. This section describes how to connect devices to the Expansion Board’s inputs and outputs.

To determine the proper wire size, see Table 9.

NOTE

Each terminal block is a removable assembly to permit easier connection of more than one input at a time. If making multiple connections, grasp the upper portion of a block and pull firmly until the assembly pulls apart.

After making the connections, push the removed piece back into the portion attached to the printed wiring assembly until the terminal block pieces lock together.

5.2.1 Connecting Digital Inputs

The 16 digital inputs are found on the lower portion of the Expansion Board, as shown below. These inputs are numbered 9 through 24 (the Universal Monitor’s digital inputs are numbered 1 through 8).

68AO

Wiring and Connections - Optional Expansion Board

V1 V3 V5 V7 V9 V11 V13 V15

EIA485 + (to UM-) 0V EIA485 - (to UM+)

S4 S3 S2 S1

K2 K3 K4 K5 K6 K7 K8

OUT1

OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

Numbering keys

DEFAULT SETTINGS FOR USE WITH UNIVERSAL MONITOR

INPUT TERMINAL BLOCKS Note numbering keys below terminal blocks; inputs are numbered from left (9) to right (24)

To connect an input:

1. Disconnect all electrical power from the Expansion Board.

2. If necessary, remove a conduit knockout to permit wire entry into the Expansion Board enclosure.

3. Bring the wire(s) into the Expansion Board enclosure through a conduit knockout or access slot.

4. Loosen the appropriate screw and slip the stripped end of the wire into the terminal block.

5. Tighten the screw until it holds the wire snugly.

5.2.2 Connecting Digital Outputs

The eight digital outputs are found at the top of the Expansion Board, as shown below. These inputs are numbered 9 through 16. (Note that the digital outputs on the main board of the Universal Monitor are numbered 1 - 8.)

OUTPUT TERMINAL BLOCKS - Note numbering keys above terminal blocks; outputs are numbered from left (9) to right (16)

Wiring and Connections - Optional Expansion Board

USE COPPER (CU) CONDUCTORS ONLY.

POWER INPUT RELAY OUTPUTS

WARNING

“RISK OF ELECTRIC SHOCK” - Hazardous voltage may be present. More than one

Numbering keys

Multiflex

810-306

V2 V4 V6 V8 V10 V12 V14 V16

disconnect switch may be required to de-energize the equipment before servicing.

CAUTION

Segregate and install separate electrical conduits for non-class 2 circuits in accordance with local building codes.

Each output may be wired according to whether you want the output to be Normally Open or Normally Closed. The Expansion Board outputs are Form C relay contacts, each with three terminals. There are two ways to wire the outputs, as shown in Figure 11.

• One wire of the two-wire connection should always be connected to the middle terminal.

• The second wire may be connected to either the N.C. terminal or the N.O. terminal, depending on how whether you want the contact to be closed or open during a power failure:

• Connect to the N.C. terminal if you want the path to be CLOSED during a power failure, or

• Connect to the N.O. terminal if you want the path to be OPEN during a power failure.

Your choice for wiring the output contacts also determines how to set the fail-safe DIP switches for proper operation (see 5.2.3 - Setting the Digital Output DIP Switches).

Figure 11 Form C output contact wiring

N.C.

Wire connected to N.C. terminal:

Relay is CLOSED on power failure

N.O.

To connect an output:

1. Disconnect electrical power from the Expansion Board.

2. If necessary, remove a conduit knockout to permit wire entry into the Expansion Board enclosure.

3. Bring the wire(s) into the Expansion Board enclosure through a conduit knockout or access slot.

4. Loosen the appropriate screw and slip the stripped end of the wire into the terminal block.

5. Tighten the screw until it holds the wire snugly.

One wire MUST be connected to middle terminal

N.C.

N.O.

Wire connected to N.O. terminal:

Relay is OPEN on power failure

5.2.3 Setting the Digital Output DIP Switches

Each digital output on the optional Expansion Board has an associated DIP switch that can determine its operation in the event of loss of communication with the Universal Monitor or loss of power.

When the Universal Monitor calls for an Expansion Board output to be ON, it sends a command to the Expansion Board to turn the output to the ON state; this is signified by the output LED being ON. The behavior of the output when it is ON is determined by the position of the DIP switch.

The DIP switches for the outputs are on a switch bank on the right side of the Expansion Board, as shown below. Each switch corresponds to an output on the board in order from left to right—for example, DIP switch 1 corresponds to Output 9; DIP switch 2 corresponds to Output 10.

Optional Expansion Board

POWER INPUT

Multiflex 168AO

810-3065

V1 V3 V5 V7 V9 V11 V13 V15

Wiring and Connections - Optional Expansion Board

USE COPPER (CU) CONDUCTORS ONLY.

RELAY OUTPUTS

V2 V4 V6 V8 V10 V12 V14 V16

EIA485 + (to UM-) 0V EIA485 - (to UM+)

DEFAULT SETTINGS FOR USE WITH UNIVERSAL MONITOR

S4 S3 S2 S1

K2 K3 K4 K5 K6 K7 K8

OUT1

OUT2 OUT3 OUT4 OUT5 OUT6 OUT7 OUT8

Digital output DIP switches

Tables 10 and 11 show how to set the DIP switch for each output based on how the output is wired (see 5.2.2 - Connecting Digital Outputs) and how you want it to perform during normal operation, when communication with the Universal Monitor is lost or when power fails.

NOTE

After a loss of communications with the Universal Monitor, there is a time delay—about five minutes—before the Expansion Board changes the state of an output.

Table 10 DIP switch setting - outputs wired as Normally Closed (N.C.)

If Output

DIP Switch

is:

Light isONLight is

State of Output When:

Communication

OFF

with UM is Lost

Power

Fails

Up (ON) Closed Open Closed Closed

Down (OFF) Open Closed Closed Closed

N.C.

N.O.

Wire connected to N.C. terminal

Table 11 DIP switch setting - outputs wired as Normally Open (N.O.)

If Output

DIP Switch

is:

Light isONLight is

State of Output When:

Communication

OFF

with UM is Lost

Power

Fails

Up (ON) Open Closed Open Open

Down (OFF) Closed Open Open Open

N.C.

N.O.

Wire connected to N.O. terminal

The Expansion Board comes from the factory with all digital output DIP switches in the OFF position (normally open). The DIP switch setting for each digital output can be changed to ON (normally closed).

To change the state of any output to the factory default of NO (Normally Open) or to NC (Normally Closed), move each switch to the appropriate position:

• Move the switch down to the OFF position for NO (Normally Open)—the default setting.

• Move the switch up to the ON position for NC (Normally Closed).

5.3 Connect to the Universal Monitor

Two steps are required to establish connection between the optional Expansion Board and the Universal Monitor.

5.3.1 Connect EIA485 Connectors to Main Board

To connect the optional Expansion Board to the Universal Monitor:

1. Turn OFF electrical power to the Universal Monitor and disconnect power from the Expansion Board.

2. If necessary, remove a conduit knockout to permit wire entry into each enclosure.

3. Bring the wire(s) into each enclosure through a conduit knockout or access slot.

4. Loosen the appropriate screw and slip the stripped end of the wire into the terminal block, connecting the cables as shown in the figure below):

• Connect the Universal Monitor 485 connector UM- to Expansion Board connector EIA485+.

• Connect the Universal Monitor 485 connector UM+ to Expansion Board connector EIA485-.

UNIVERSAL MONITOR EIA485 connector

Wiring and Connections - Optional Expansion Board

OPTIONAL EXPANSION BOARD EIA485 connector

UM-

UM+

TB10: COMM

(TOP)

(BOTTOM)

—

422

—

Connect UM+ to EIA485-

5. Tighten each screw until it holds the wire snugly.

5.3.2 Enable the Connection via Firmware

After making the cable connections described in the previous section, you must specify the Expansion Board as connected using either the LCD or Service Terminal Interface.

For instructions, refer to the appropriate section:

• LCD interface (see 9.10 - Setup Exp Board - Optional Expansion Board)

• Service Terminal Interface (see A.6.8 - Connect Expansion Board)

Connect UM- to EIA485+

EIA485+

EIA485 + (to UM-) 0V EIA485 - (to UM+)

EIA485-

POWER INPUT

810-3065

S4 S3 S2 S1

Multiflex 168AO

Overview of Menus

6.0 OVERVIEW OF MENUS

There are two ways to access the Universal Monitor: the LCD on the front of the enclosure and the Service Terminal Interface, which is accessible through any computer using a communications program. Many viewing and configuration tasks can be performed through either interface, but some are available only through the Service Terminal Interface.

• Step-by-step instructions for all functions appear in Sections 7.0 through 9.0. These instructions use examples of LCD screens to illustrate most functions, except those not available via the LCD.

• Examples of all Service Terminal Interface screens appear in Appendix A - Service Terminal

Interface, along with instructions on how to connect to the Service Terminal Interface.

Table 12 lists all Universal Monitor functions and shows whether they can be performed through the

LCD interface and where to find information.

Table 12 Guide to Universal Monitor functions

Can be performed via: Where to find:

Function

VIEW STATUS FUNCTIONS

View Active Alarms ✔✔ page 33 page 93 View Alarm Log ✔✔ page 34 page 94 View Event Log ✔✔ page 35 page 95 View Trend Log ✔✔ page 36 page 96 View Input Status ✔✔ page 37 page 97 View Output Status ✔✔ page 38 page 98 View Pager Numbers ✔✔ page 39 page 99

SILENCE ALARM & BACK UP LOGS FUNCTIONS

Silence Alarm (On the LCD, press any key to silence an alarm) ✔✔ page 40 page 100 Back Up Log Files — ✔ page 41 page 101

SYSTEM & CONTROL FUNCTIONS

Setup System ✔✔ page 45 page 105

Setup Input ✔✔ page 45 page 106 Setup Common Alarm ✔✔ page 48 page 108 Setup Sensor ✔✔ page 49 page 109 Setup I/O Matrix ✔✔ page 55 page 111 Setup Output ✔✔ page 58 page 117 Pager Setup - Pager Number & PIN ✔✔ page 64 page 119 Pager Setup - Communications Check — ✔ page 66 page 119 Modem Setup - Initialization String ✔✔ page 60 page 120 Modem Setup - Enter Universal Monitor Phone Number — ✔ page 62 page 120 Modem Setup - Enable Modem Diagnostic Messages — ✔ page 62 page 120 Modem Setup - Change Modem Dial Prefix — ✔ page 62 page 120 Modem Setup - Change Modem Hang Up Delay After a Call — ✔ page 62 page 120

Setup System Info ✔✔ page 68 page 121

Change Password ✔✔ page 69 page 121 Change Date & Time/Automatic Daylight Saving Time ✔✔ page 69 page 122 Setup Site ID ✔✔ page 70 page 122 Connect Battery ✔✔ page 70 page 123 Backup and Upload Configuration File — ✔ page 71 page 123 Setup Serv Ph Num - Enter Phone Number ✔✔ page 74 page 124 Setup Serv Ph Num - Communications Check — ✔ page 75 page 124 Factory Defaults ✔✔ page 76 page 125 Perform Firmware Update — ✔ page 76 page 125 Initiate Remote Alarm Test — ✔ page 78 page 126

Setup Exp Board - Optional Expansion Board ✔✔ page 79 page 127 Manual Output Ctrl ✔✔ page 80 page 128 Clear Alarms & Logs ✔✔ page 81 page 130

Clear Active Alarms ✔✔ page 81 page 130 Clear the Alarm Log ✔✔ page 81 page 130 Clear the Event Log ✔✔ page 82 page 131 Clear the Trend Logs ✔✔ page 82 page 131

LCD

Service

Terminal

Instructions on

using function

Service Terminal

screen examples

6.1 Opening Screen Overview

The Universal Monitor displays the Opening Screen at startup, as shown in Figure 12.

• If any alarms are active, the Current Alarm screen appears. (Pressing any key on the LCD keypad will silence the audible alarm.)

• If any analog input sensors are connected, the LCD screen will alternately display the Opening Screen and a screen showing the analog value of each sensor.

If no alarms are present, the Main Menu appears.

6.2 Main Menu Overview

The Main Menu offers access to all functions within the panel. As shown in Table 13, the functions are organized into three sections with step-by-step instructions.

Table 13 Primary Functions Overview

Section Description

7.0 - View Status Options

(both LCD and Service Terminal Interface)

8.0 - Silence Alarm & Backup Log Files (Service

Terminal Interface only)

9.0 - System and Control Options (some functions

available via Service Terminal Interface only)

These features are available to all users. This permits all personnel to check the status of any monitored equipment or location. From this menu, any user may:

• View current monitoring data—active alarms and the status of inputs and outputs

• View data stored in alarm, event and trend logs

• View pager numbers These features—available via the Service Terminal Interface only—allow users to:

• Silence the audible alarm

• Back up the alarm, event and trend logs These options require a password. Authorized users may:

• Configure the Universal Monitor

• Override automatic control of outputs to force an output ON or OFF

• Clear active alarms and delete all records in the alarm, event and trend logs

Overview of Menus

6.3 LCD Menu Overview

Figure 12 shows an overview of the initial screens available through the LCD interface. For comparable information about the Service Terminal Interface screens, see A.3 - Overview of Menus.

Figure 12 LCD Menu overview

“View Status” selected

> VIEW STATUS

SYSTEM AND CONTROL

↑↓=NEXT

View Status Menu

(All users - no password)

VIEW ACTIVE ALARMS VIEW ALARM LOG VIEW EVENT LOG VIEW TREND LOG VIEW INPUT STATUS VIEW OUTPUT STATUS VIEW PAGER NUMBERS

↵ =SELECT

Opening Screen

UNIVERSAL MONITOR DD-MON-YY HR:MM:SS

PRESS

VX.XXX.X

↵ =STATUS/SETUP

Main Menu

VIEW STATUS SYSTEM AND CONTROL

↑↓=NEXT

See Section

7.0

See Section

7.1

7.2

7.3

7.4

7.5

7.6

7.7

↵=SELECT

(If any alarms detected)

Current Alarm screen (see 7.1 - View Active Alarms)

“System & Control” selected

VIEW STATUS

> SYSTEM AND CONTROL

↑↓=NEXT

↵ =SELECT

System & Control Menu

(Password required)

SETUP SYSTEM MANUAL OUTPUT CTRL CLEAR ALARMS & LOGS

See Section

9.0

See Section

9.2

9.11

9.12

7.0 VIEW STATUS OPTIONS

NOTE

For ease of understanding, this section uses the LCD interface to illustrate most instructions, except for features that are available only through the Service Terminal Interface. All Service Terminal Interface screens appear in Appendix A - Service Terminal Interface.

The View Status menu allows any user to view currently active alarms, monitoring data stored in the alarm, event and trend logs, the status of all inputs and outputs, and the four pager numbers. The arrows

This section presents step-by-step instructions for each of the following options:

Figure 13 shows the main options available from the View Status menu.

Figure 13 Menu overview - View Status menu

↑↓ are used to scroll through the menu. The Enter ↵ key is used to select the menu item.

• View Active Alarms

•View Alarm Log

•View Event Log

• View Trend Log

• View Input Status

• View Output Status

• View Pager Numbers

Opening Screen

UNIVERSAL MONITOR DD-MON-YY HR:MM:SS

PRESS ↵ =STATUS/SETUP

View Status Options

VX.XXX.X

Main Menu

> VIEW STATUS

SYSTEM AND CONTROL

↑↓=NEXT ↵ =SELECT

View Status

VIEW ACTIVE ALARMS VIEW ALARM LOG VIEW EVENT LOG VIEW TREND LOG VIEW INPUT STATUS VIEW OUTPUT STATUS VIEW PAGER NUMBERS

View Status options

View Active Alarms View Alarm Log View Event Log View Trend Log

> ACTIVE ALARM 33/33

SENSOR_1 101.0 DEG HIGH SETPOINT ALARM

SENSOR_2 ------ DEG SENSOR PROBLEM

INPUT_07 ALARM CONTACT OPEN

BATTERY CHECK BATTERY

See Section

7.1

> ALARM RECORD 99/99

SENSOR_2 80.0 DEG HIGH SETPOINT ALARM 29-AUG-02 09:29:10

MODEM INTERNAL FAULT 29-AUG-02 09:20:00

INPUT_08 ALARM CONTACT CLOSED 29-AUG-02 07:30:00

See Section

7.2

> EVENT RECORD 99/99

PAGER UNSUCCESSFUL PAGE 07-MAY-02 10:07:00

OUTPUT01 MAN ON CONTACT CLOSED 06-MAY-02 02:47:03

OUTPUT08 ON CONTACT OPEN 05-MAY-02 05:22:17

See Section

7.3

SENSOR TO VIEW?

> SENSOR_1

SENSOR_2 SENSOR_3 SENSOR_4

> TREND LOG 100/100

SENSOR_1 75.4 DEG NORMAL 28-AUG-02 15:45:51

View Input Status View Output Status View Pager Numbers

16 additional inputs for optional Expansion Board

INPUT / STATUS

> SENSOR_1 +80.00 DEG

SENSOR_2 ------ DEG SENSOR_3 SENSOR_4 +79.50 RH INPUT_01 NORMAL INPUT_02 ALARM INPUT_03 EVENT INPUT_04 ALARM INPUT_05 ALARM INPUT_06 EVENT INPUT_07 NORMAL INPUT_08 NORMAL INPUT_09 NORMAL

. . .

INPUT_24 NORMAL

See Section

7.5

8 add’l outputs for optional Expansion Board

OUTPUT / STATUS

> OUTPUT01 ON

OUTPUT02 OFF OUTPUT03 ON OUTPUT04 MAN ON OUTPUT05 ON OUTPUT06 OFF OUTPUT07 MAN OFF OUTPUT08 ON OUTPUT09 OFF

. . .

OUTPUT16 OFF

See Section

7.6

9,,18005551212##

> PAGER NUMBER 1

VIEW PAGER NUMBER VIEW PAGER PIN

PAGER 1 NUMBER

PAGER TO VIEW?

PAGER NUMBER 2 PAGER NUMBER 3 PAGER NUMBER 4

01234567891011121344

See Section

7.7

PAGER 1 PIN

See Section

7.4

View Status Options

7.1 View Active Alarms

The Active Alarm screen displays all alarms that are occurring, up to a maximum of 33.

A Current Alarm screen appears automatically whenever an alarm occurs—except during setup. This screen can display only the two most recent active alarms. To view any other active alarms, use the View Active Alarms feature.

You may view active alarms at any time by using the following steps:

• From the Main Menu, use the arrows

shown at right, and then press Enter ↵ .

• From the View Status Menu, use the arrows

Active Alarms and press Enter ↵ .

7.1.1 Active Alarms

The Active Alarms screen displays up to 33 records; it shows any active alarm and any Latched alarm that has not been cleared. Examples of alarms include inputs in alarm status, a low battery condition and a loss of connection to an analog input. When any alarms are present, the Active Alarms screen shows descriptive details for each alarm:

• the source of the alarm (for example,

• the status of an input or output (

• a brief description of the problem (

BATTERY)

If there are no active alarms, the screen displays the message:

↑↓ to choose View Status, as

↑↓ to choose View

SENSOR_1 or BATTERY)

101.0 DEG) HIGH SETPOINT ALARM or CHECK

Main Menu

> VIEW STATUS

SYSTEM AND CONTROL

↑↓=NEXT

↵ =SELECT

View Status Menu

> VIEW ACTIVE ALARMS

VIEW ALARM LOG VIEW EVENT LOG VIEW TREND LOG

VIEW INPUT STATUS VIEW OUTPUT STATUS VIEW PAGER NUMBERS

Active Alarms

> ACTIVE ALARM 33/33

SENSOR_1 101.0 DEG HIGH SETPOINT ALARM

SENSOR_2 ------ DEG SENSOR PROBLEM

INPUT_07 ALARM CONTACT OPEN

BATTERY CHECK BATTERY

NO ALARMS PRESENT

Viewing Additional Screens

There may be up to 33 records of alarm data.

• To view additional records, use the arrows

↑↓.

• To return to the previous screen, press the ESC key.

Clearing Active Alarms

To clear all active alarms, see 9.12 - Clear Alarms & Logs. Alarm records are stored in the Alarm Log.

View Status Options

7.2 View Alarm Log

The Alarm Log contains up to 99 records of alarms that have occurred. Records are added to this log as alarms occur.

To view the Alarm Log:

• From the Main Menu, use the arrows

then press Enter ↵.

• From the View Status Menu, use the arrows

Alarm Log, then press Enter ↵ .

7.2.1 Alarm Log

The Alarm Log screen displays up to 99 records showing alarm data, including input alarms and other conditions, such as loss of power or low battery. If the log contains any alarm records, the Alarm Log screen displays details for each alarm:

• the source of the alarm (for example,

• the status of an input or output (

• a brief description of the problem (

NAL FAULT)

• the date and time the alarm occurred

Table 14 shows conditions that the alarm log records for digital inputs and analog inputs and in the panel itself.

Table 14 Alarm log conditions

SOURCE Digital Input Analog Input Panel

CONDITIONS RECORDED

ALARM NORMAL

↑↓ to choose View Status,

↑↓ to choose View

SENSOR_2 or MODEM)

80.0 DEG) HIGH SETPOINT ALARM or INTER-

HIGH SETPOINT ALARM LOW SETPOINT ALARM RETURN TO NORMAL SENSOR PROBLEM (denoted by dashes ------)

Main Menu

> VIEW STATUS

SYSTEM AND CONTROL

↑↓=NEXT

↵ =SELECT

View Status Menu

VIEW ACTIVE ALARMS

> VIEW ALARM LOG

VIEW EVENT LOG VIEW TREND LOG

VIEW INPUT STATUS VIEW OUTPUT STATUS VIEW PAGER NUMBERS

Alarm Log

> ALARM RECORD 99/99

SENSOR_2 80.0 DEG HIGH SETPOINT ALARM 29-AUG-02 09:29:10

MODEM INTERNAL FAULT 29-AUG-02 09:20:00

INPUT_08 ALARM CONTACT CLOSED 29-AUG-02 07:30:00

LOSS OF POWER LOW BATTERY CHECK BATTERY BATTERY UNPLUGGED ALARM SILENCED MODEM INTERNAL FAULT ALARMS CLEARED EXP BRD LOSS OF COMM EXP BRD RESTORE COMM

If there are no alarms in the log, the screen displays the message:

NO ALARMS

Viewing Additional Screens

There may be up to 99 records of alarm data.

• To view additional records, use the arrows

↑↓.

• To return to the previous screen, press the ESC key.

7.2.2 Backing Up the Alarm Log (Service Terminal Interface only)

The alarm log is stored as a file in the Universal Monitor; it can hold no more than 99 records. When the log is full, the oldest records are deleted from the end of the file as new alarm records are added at the beginning.

You may back up the alarm log file to a remote computer using the Service Terminal Interface, as described in 8.2 - Back Up Log Files (Service Terminal Interface only).

To delete all records in the alarm log, see 9.12 - Clear Alarms & Logs.

View Status Options

7.3 View Event Log

In addition to alarms, the Universal Monitor tracks other changes in the Event Log to assist users with verifying operational and troubleshooting problems. Events reflect changes in the status of an input that is defined as an event or the change of state of an output (i.e., manually forced ON or OFF). Other events may be informational, such as a user login or an unsuccessful page attempt. The Event Log contains up to 99 records of events, which are added as they occur.

To view the Event Log:

• From the Main Menu, use the arrows

then press Enter ↵.

• From the View Status Menu, use the arrows

Event Log, then press Enter ↵ .

7.3.1 Event Log

The Event Log screen displays up to 99 recent events. If the log contains any event records, the Event Log screen displays details for each event:

• the event source (for example,

• the status of an input or output (

• a brief description of the event (

CLOSED

• the date and time the event occurred

)

↑↓ to choose View Status,

↑↓ to choose View

PAGER or OUTPUT01)

MAN ON)

UNSUCCESSFUL PAGE or CONTACT

Main Menu

> VIEW STATUS

SYSTEM AND CONTROL

↑↓=NEXT

↵ =SELECT

View Status Menu

VIEW ACTIVE ALARMS VIEW ALARM LOG

> VIEW EVENT LOG

VIEW TREND LOG VIEW INPUT STATUS

VIEW OUTPUT STATUS VIEW PAGER NUMBERS

Event Log

> EVENT RECORD 99/99

PAGER UNSUCCESSFUL PAGE 07-MAY-02 10:07:00

OUTPUT01 MAN ON CONTACT CLOSED 06-MAY-02 02:47:03

OUTPUT08 ON CONTACT OPEN 05-MAY-02 05:22:17

Table 15 shows conditions that the event log records for inputs and outputs and in the panel itself.

Table 15 Event log conditions

SOURCE Digital Input Analog Input Digital Output Panel

CONDITIONS RECORDED

EVENT NORMAL

HIGH SETPOINT EVENT LOW SETPOINT EVENT RETURN TO NORMAL SENSOR PROBLEM

(denoted by dashes ------)

MAN ON MAN OFF AUTO HW MAN ON ON OFF

If there are no records in the log, the screen displays the message:

NO EVENTS

Viewing Additional Screens

There may be up to 99 records of event data.

• To view additional records, use the arrows

↑↓.

• To return to the previous screen, press the ESC key.

7.3.2 Backing Up the Event Log (Service Terminal Interface only)

The event log is stored as a file in the Universal Monitor; it can hold no more than 99 records. When the log is full, the oldest records are deleted from the end of the file as new event records are added at the beginning.

ALARMS CLEARED ALARM SILENCED DIAL OUT TEST PASSED DIAL OUT TEST FAILED UNSUCCESSFUL PAGE MODEM RESET TIME & DATE SET USER LOGIN

You may back up the event log file to a remote computer using the Service Terminal Interface, as described in 8.2 - Back Up Log Files (Service Terminal Interface only).

To delete all records in the event log, see 9.12 - Clear Alarms & Logs.

View Status Options

7.4 View Trend Log

The Universal Monitor takes readings of configured analog input sensors at regular intervals and stores them in four separate trend logs, one for each sensor. The time interval is 30 minutes. Each log contains up to 100 records.

Follow these steps to select a sensor and view its trend log:

7.4.1 Select a Sensor

To select a sensor:

• From the Main Menu, use the arrows

then press Enter ↵.

• From the View Status Menu, use the arrows

Trend Log, then press Enter ↵ .

• From the Sensor Selection Menu, use the arrows sensor you want to view—Sensor_1 in the example at right—and press Enter ↵ .

7.4.2 View a Trend Log

The Trend Log screen displays up to 100 records for the selected sensor. If the log contains records, the screen displays details for each reading:

• the name of the selected sensor (for example,

•the reading (

• a brief description of the reading status (

• the date and time of the reading

Table 16 shows conditions that the trend log records for analog inputs. Each analog input has its own trend log.

Table 16 Trend log conditions

SOURCE Analog Input

CONDITIONS RECORDED

75.4 DEG)

LOW SETPOINT ALARM LOW SETPOINT EVENT HIGH SETPOINT ALARM HIGH SETPOINT EVENT RETURN TO NORMAL NORMAL SENSOR PROBLEM (denoted by dashes ------)

↑↓ to choose View Status,

↑↓ to choose View

↑↓ to choose the

SENSOR_1)

NORMAL)

Main Menu

> VIEW STATUS

SYSTEM AND CONTROL

↑↓=NEXT

↵ =SELECT

View Status Menu

VIEW ACTIVE ALARMS VIEW ALARM LOG VIEW EVENT LOG

> VIEW TREND LOG

VIEW INPUT STATUS VIEW OUTPUT STATUS VIEW PAGER NUMBERS

Select Sensor Menu

SENSOR TO VIEW?

> SENSOR_1

SENSOR_2 ↑↓=NEXT ↵ =SELECT

SENSOR_3 SENSOR_4

Trend Log

> TREND LOG 100/100

SENSOR_1 75.4 DEG NORMAL 28-AUG-02 15:45:51

SENSOR_1 70.5 DEG LOW SETPOINT EVENT 28-AUG-02 15:15:51

SENSOR_1 79.9 DEG RETURN TO NORMAL 28-AUG-02 14:45:21

If there are no records in the log, the screen displays the message:

NO TRENDS

Viewing Additional Screens

There may be up to 100 records of trend data for the selected sensor.

• To view additional records, use the arrows

↑↓.

• To return to the previous screen, press the ESC key.

7.4.3 Backing Up the Trend Log (Service Terminal Interface only)

The four trend logs are stored as files in the Universal Monitor, with a maximum of 100 records per sensor. When a log is full, the oldest records are deleted from the end of the file as new trend records are added at the beginning.

You may back up each trend log file to a remote computer using the Service Terminal Interface, as described in 8.2 - Back Up Log Files (Service Terminal Interface only).

To delete all records in the trend logs, see 9.12 - Clear Alarms & Logs.

View Status Options

7.5 View Input Status

The Input Status option allows you to view the current status of all inputs: the four analog sensor inputs and the eight digital inputs. If the optional Expansion Board is used, the additional 16 digital inputs can also be viewed.

To view the Input Status:

• From the Main Menu, use the arrows then press Enter ↵.

• From the View Status Menu, use the arrows Input Status, then press Enter ↵ .

7.5.1 Input Status

The Input Status screen displays the status of each analog sensor and digital input.

Analog Sensor Inputs

The following details are displayed for analog sensor inputs:

• the name of the analog sensor input (for example,

• the current reading ( while being viewed

There are three possible states for an analog input, as shown in Table 17.

Table 17 Analog input states

State Description

Functional Reading—-for example, +80.00 DEG or +79.50 RH Problem with

connection Not configured Blank

NOTE

If the status displays dashes ( was unable to take a reading. There may be a connection problem.

If the status is blank, the sensor is not configured as being connected.

Digital Inputs

The following details appear for digital inputs:

• the name of the digital input (for example,

• the current status ( being viewed

There are three possible states for a digital input, as shown in Table 18.

Table 18 Digital input states

State Description

NORMAL In normal state ALARM In alarm status (for an input configured as alarmable) EVENT An event has occurred (for an input configured as an event)

Dashes (------)

↑↓ to choose View Status,

↑↓ to choose View

SENSOR_1)

+80.00 DEG)—values are updated constantly

------), the Universal Monitor

INPUT_01)

NORMAL)—values are updated constantly while

Main Menu

> VIEW STATUS

SYSTEM AND CONTROL

↑↓=NEXT

↵ =SELECT

View Status Menu

VIEW ACTIVE ALARMS VIEW ALARM LOG VIEW EVENT LOG VIEW TREND LOG

> VIEW INPUT STATUS

VIEW OUTPUT STATUS VIEW PAGER NUMBERS

Input Status

INPUT / STATUS

> SENSOR_1 +80.00 DEG

SENSOR_2 ------ DEG SENSOR_3

SENSOR_4 +79.50 RH INPUT_01 NORMAL INPUT_02 ALARM INPUT_03 EVENT INPUT_04 ALARM INPUT_05 ALARM INPUT_06 EVENT INPUT_07 NORMAL INPUT_08 NORMAL INPUT_09 NORMAL INPUT_10 ALARM INPUT_11 EVENT INPUT_12 ALARM INPUT_13 ALARM INPUT_14 EVENT INPUT_15 NORMAL INPUT_16 NORMAL INPUT_17 NORMAL INPUT_18 ALARM INPUT_19 EVENT INPUT_20 ALARM INPUT_21 ALARM INPUT_22 EVENT INPUT_23 NORMAL INPUT_24 NORMAL

NOTE: 16 additional inputs (INPUT_09 thru INPUT_24) for optional Expansion Board

Viewing Additional Input Data

All input data may be viewed by scrolling beyond the four lines that appear on the LCD at one time:

• To view all inputs, use the arrows

• To return to the previous screen, press the ESC key.

↑↓.

View Status Options

7.6 View Output Status

The Output Status option allows you to view the current status of all eight outputs. If the optional Expansion Board is used, the additional eight digital outputs can also be viewed.

To view the Output Status:

• From the Main Menu, use the arrows then press Enter ↵.

• From the View Status Menu, use the arrows Output Status, then press Enter ↵ .

7.6.1 Output Status

The Output Status screen displays the status of each digital output.

The following details appear for digital outputs:

• the name of the output (for example,

• the current status ( viewed

There are five possible states for a digital output, as shown in Table 19.

Table 19 Digital output states

State Description

ON Automatic OFF Automatic MAN ON Manually ON This output forced ON or OFF

MAN OFF Manually OFF

HW MAN ON

Manually ON (all outputs)

↑↓ to choose View Status,

↑↓ to choose View

OUTPUT01)

ON)—values are updated constantly while being

Controlled by Universal Monitor

via Manual Output Ctrl menu or SiteScan Web

All outputs forced ON via hardware switch on circuit board

Main Menu

> VIEW STATUS

SYSTEM AND CONTROL

↑↓=NEXT

↵ =SELECT

View Status Menu

VIEW ACTIVE ALARMS VIEW ALARM LOG VIEW EVENT LOG VIEW TREND LOG

VIEW INPUT STATUS

> VIEW OUTPUT STATUS

VIEW PAGER NUMBERS

Output Status

OUTPUT / STATUS

> OUTPUT01 ON

OUTPUT02 OFF OUTPUT03 ON

OUTPUT04 MAN ON OUTPUT05 ON OUTPUT06 OFF OUTPUT07 MAN OFF OUTPUT08 ON OUTPUT09 ON OUTPUT10 OFF OUTPUT11 ON OUTPUT12 MAN ON OUTPUT13 ON OUTPUT14 OFF OUTPUT15 MAN OFF OUTPUT16 ON

Viewing Additional Output Data

All output data may be viewed by scrolling beyond the four lines that appear on the LCD at one time:

• To view all outputs, use the arrows

• To return to the previous screen, press the ESC key.

↑↓.

NOTE: 8 additional outputs (OUTPUT09 thru OUTPUT16) for optional Expansion Board

View Status Options

7.7 View Pager Numbers

The Universal Monitor may be set up to dial pager numbers when an alarm is detected. Up to four pagers may be configured, as described in

9.8 - Setup System - Setup Modem & Pagers.

The View Pager Numbers option allows you to view the pager numbers and PINs for all configured pagers. Use the following steps to select a pager and view its information.

7.7.1 Select a Pager

To select a pager:

• From the Main Menu, use the arrows then press Enter ↵.

• From the View Status Menu, use the arrows Pager Numbers, then press Enter ↵ .

• From the Pager Selection screen, use the arrows pager you want to view—Pager Number 1 in the example at right—and press Enter ↵ .

• Use the following steps to view a pager number or PIN for the selected pager.

7.7.2 View a Pager Number

To view a pager number:

• Choose View Pager Number from the Pager Menu and press Enter ↵ .

• The Pager Number screen displays the number that is configured for the selected pager.

In the example at right, the telephone number is preceded by A to dial an alphanumeric pager and includes a comma (,) to pause two seconds after dialing “1” before proceeding to dial the area code and number. To change this number, see 9.8.3 - Pager Setup - Pager Number and PIN.

• Press ESC to return to the Pager Menu.

↑↓ to choose View Status,

↑↓ to choose View

↑↓ to choose the

Main Menu

> VIEW STATUS

SYSTEM AND CONTROL

↑↓=NEXT

↵ =SELECT

View Status Menu

VIEW ACTIVE ALARMS VIEW ALARM LOG VIEW EVENT LOG VIEW TREND LOG

VIEW INPUT STATUS VIEW OUTPUT STATUS

> VIEW PAGER NUMBERS

Pager Selection

PAGER TO VIEW?

> PAGER NUMBER 1

PAGER NUMBER 2 PAGER NUMBER 3

PAGER NUMBER 4

Pager Menu

> VIEW PAGER NUMBER

VIEW PAGER PIN

Pager Number

PAGER 1 NUMBER

A1,8005551212

7.7.3 View a Pager PIN

To view a pager PIN:

• Choose View Pager PIN from the Pager Menu and press Enter ↵ .

• The Pager PIN screen displays the PIN that is configured for the selected pager. To change this number, see 9.8 - Setup System - Setup Modem & Pagers.

• Press ESC to return to the Pager Menu.

Pager Menu

VIEW PAGER NUMBER

> VIEW PAGER PIN

Pager PIN

PAGER 1 PIN

01234567891011121344

Silence Alarm & Backup Log Files (Service Terminal Interface)

8.0 SILENCE ALARM & BACKUP LOG FILES (SERVICE TERMINAL INTERFACE)

This section describes two features that are available in the Service Terminal Interface:

• Silence Alarm

• Backup Log Files

8.1 Silence Alarm (Service Terminal Interface)

The Silence Alarm menu item allows you to silence the audible alarm and reset the Common Alarm Relay output if the common alarm is configured to reset with silence.

This menu item is available only through the Service Terminal Interface and SiteScan Web connection.

NOTE

An alarm may also be silenced by pressing any key on the LCD keypad on the front of the Universal Monitor. The LCD does not offer Silence Alarm as a menu item.

To silence the alarm remotely through the Service Terminal Interface:

• Connect to the Universal Monitor either from a remote computer or through the RS232 port (see A.2 - Connecting to the Service Terminal Interface).

• At the Main Menu, enter 8 (Silence Alarm).

• At the Silence Alarm menu, shown below, enter 1 to silence the audible alarm immediately. (To exit without silencing the alarm, enter 2 or press the Escape key.)

Silence Alarm (Service Terminal Interface only)

SILENCE ALARM

Silence alarm and reset common alarm relay if common alarm relay is configured to reset with silence alarm

1=SILENCE ALARM 2=RETURN TO MAIN MENU

SELECT A NUMBER:1

>ALARM HAS BEEN SILENCED

• A confirmation message appears: “Alarm has been silenced.”

NOTE

Through SiteScan Web, this option is available via the Universal Monitor Graphic Screen.

Silence Alarm & Backup Log Files (Service Terminal Interface)

8.2 Back Up Log Files (Service Terminal Interface only)

The Universal Monitor maintains three types of logs—alarm, event and trend—that may be backed up to a remote computer.

This feature is available only through the Service Terminal Interface.

To back up any of the alarm, event or trend logs:

1. Connect to the Universal Monitor either from a remote computer or through the RS232 port (see A.2 - Connecting to the Service Terminal Interface).

2. At the Main Menu, enter 9 (Backup Log Files).

3. At the Backup Log Files menu, as shown below, enter a number for the type of file you want to back up:

• Enter 1 to back up the Alarm Log

• Enter 2 to back up the Event Log

• Enter 3 to back up the Trend Log for the first sensor (Sensor_1)

• Enter 4 to back up the Trend Log for the second sensor (Sensor_2)

• Enter 5 to back up the Trend Log for the third sensor (Sensor_3)

• Enter 6 to back up the Trend Log for the fourth sensor (Sensor_4)

Backup Log Files - Alarm Log File (Service Terminal Interface only)

BACKUP LOG FILES

Backup alarm, event and trend log files

1=BACKUP ALARM LOG FILE 2=BACKUP EVENT LOG FILE 3=BACKUP TREND LOG FILE-SENSOR_1 4=BACKUP TREND LOG FILE-SENSOR_2 5=BACKUP TREND LOG FILE-SENSOR_3 6=BACKUP TREND LOG FILE-SENSOR_4 7=RETURN TO MAIN MENU

SELECT A NUMBER:1

4. At the prompt to initiate a backup of the selected log file, enter Y (Yes - begin) or N (No - cancel). The current setting appears in brackets—[N] in the following example.

>INITIATE A BACKUP OF ALARM LOG-YES(Y) OR NO(N)? >[N] >[

Silence Alarm & Backup Log Files (Service Terminal Interface)

NOTE

The following instructions refer to the Microsoft

Windows® HyperTerminal program. These

steps may vary for other communications programs.

5. At the top of the HyperTerminal window, shown below, click on Transfer, then on Receive File.

Enter folder

Select Xmodem

Enter filename for example,

alarm.log

6. In the Receive File window, as shown above:

• In the Place Received File in the Following Folder box, enter the name and location of the folder where the configuration file should be placed—for example, C:\downloads—or click on the Browse button to locate the folder.

• In the Use Receiving Protocol box, select Xmodem from the drop-down list.

• Click on the Receive button. (To close the window without backing up the file, click on Close or Cancel.)

7. In the Receive Filename window, enter a name for the log file—Alarm.log in the example above.

8. When the transfer is complete, a confirmation message appears in the Service Terminal Interface window: “Backup Successful.”

9. The display returns to the Backup Log Files menu. You may choose another type of log file to back up (return to Step 3) or press 7 (or Escape) to return to the Main Menu.

After backing up a log file, you may want to delete all records in the Universal Monitor’s log of that type. See 9.12 - Clear Alarms & Logs for details.

9.0 SYSTEM AND CONTROL OPTIONS

NOTE

The System and Control menu allows you to configure the Universal Monitor—setting up inputs and outputs and an input/output matrix to trigger actions, the modem and pagers, and system features such as date and time. This menu also provides a vehicle for manually changing the state of an output to ON or OFF, clearing active alarms and deleting records from the Universal Monitor’s alarm log, event log and trend logs.

The arrows and enter new information. Table 20 shows characters that may be entered in labels and values.

Table 20 Valid characters for data entry

Alphanumeric Special characters

A-Z, 0-9 space [ ] ^ _ ! " # $ % & ( ) * + - / , . ; < = > @

The System and Control options require a password to prevent unauthorized users from making changes to the system.

This section presents step-by-step instructions for each of the following:

• Login - enter the password

• Setup System - configure inputs, outputs, modem, pagers, system features

• Manual Output Ctrl - manually override automatic control of outputs; release the override

• Clear Alarms & Logs - clear active alarms; delete records from the alarm, event and trend logs

↑↓ are used to scroll through the menu. The Enter ↵ key is used to select the menu item

System and Control Options

9.1 Login

Users must enter a password to access any of the system and control options. The password consists of four characters (see Table 20 for valid characters). (To set up or change the password, see 9.9.1 - Change Password.)

To log in:

• From the Main Menu, use the arrows

Control, then press Enter ↵ , as shown at right.

• Use the arrows

Enter ↵ . The Login menu appears.

• To enter your password:

The System and Control Menu appears next, with these options that are described in the following sections:

• Setup System (Section 9.2 - Section 9.9)

• Manual Output Ctrl (Section 9.11)

•Clear Alarms & Logs (Section 9.12)

NOTE

If an alarm occurs while a user is logged on, the LCD backlight will flash and the audible alarm will sound. To obtain specific information about the alarm, you must access the Active Alarm screen (see 7.1 - View Active Alarms) or the Alarm Log (see 7.2 - View Alarm Log).

Main Menu

VIEW STATUS

> SYSTEM AND CONTROL

↑↓ to choose System and

↑↓ to choose System and Control, and press

• Use the arrows

↑↓ to choose a character.

• Press Enter ↵ to advance to the next character position.

• When finished, press Enter ↵ again.

↑↓=NEXT

AAAA

↑↓=SELECT ↵=NEXT/END

System & Control Menu

> SETUP SYSTEM

MANUAL OUTPUT CTRL CLEAR ALARMS & LOGS

↑↓=NEXT

↵ =SELECT

NOTE

If, after logging in, you press the ESC key to return to a previous screen that is not passwordprotected, you must log in again, including entering your password if you wish to access password-protected functions.

Figure 14 shows the main options available from the System & Control menu.

Figure 14 Menu overview - System and Control menu

Opening Screen

UNIVERSAL MONITOR DD-MON-YY HR:MM:SS

VX.XXX.X

PRESS ↵ =STATUS/SETUP

Main Menu

VIEW STATUS

> SYSTEM AND CONTROL

↑↓=NEXT ↵ =SELECT

AAAA

↑↓=SELECT ↵ =NEXT/END

System and Control Options

System & Control menu

Setup System selected

> SETUP SYSTEM

MANUAL OUTPUT CTRL CLEAR ALARMS & LOGS

System & Control menu

Manual Output Ctrl selected

SETUP SYSTEM

> MANUAL OUTPUT CTRL

CLEAR ALARMS & LOGS

System & Control menu

Clear Alarms&Logs selected

SETUP SYSTEM MANUAL OUTPUT CTRL

> CLEAR ALARMS & LOGS

Setup System menu Select Output Clear Alarms/Logs menu

SETUP INPUT SETUP COMMON ALARM SETUP SENSOR SETUP I/O MATRIX SETUP OUTPUT SETUP MODEM&PAGERS SETUP SYSTEM INFO SETUP EXP BOARD

See Section

9.2

Setup System options

OVERRIDE OUTPUT

> OUTPUT01 AUTO

OUTPUT02 AUTO

. . .

OUTPUT16 AUTO

Override Output

SELECT OUTPUT01

AUTO

See Section

9.11

CLEAR ACTIVE ALARMS ARE YOU SURE? N

CLEAR EVENT LOG ARE YOU SURE? N

CLEAR ACTIVE ALARMS CLEAR ALARM LOG CLEAR EVENT LOG CLEAR TREND LOGS

CLEAR ALARM LOG ARE YOU SURE? N

CLEAR TREND LOGS ARE YOU SURE? N

See Section

9.12

Setup Input Setup Common Alarm Setup Sensor Setup I/O Matrix

SELECT INPUT

> INPUT_01 NO-AL-NL

INPUT_02 NO-AL-NL

. . .

INPUT_24 NO-AL-NL

SETUP INPUT_01 LABEL: INPUT_01 NORM OPEN/CLOSE: NO ALARM/EVENT: AL LATCHED: N DELAY: 00:01

Setup Output Setup Modem & Pagers

SELECT OUTPUT

> OUTPUT01 NO

OUTPUT02 NO

. . .

OUTPUT16 NO

CHANGE LABEL CHANGE STATE

See Section

9.3

See Section

9.7

RESET COMMON ALARM WITH SILENCE? N

SETUP PAGERS SETUP MODEM

SELECT PAGER

PAGER NUMBER 1

. . .

PAGER NUMBER 4

See Section

9.4

See Section

9.8

ENTER INIT STRING ATS0=1

SELECT SENSOR

> SENSOR_1 +80.00 DEG

. . .

SENSOR_4 +79.50 RH

SETUP SENSOR_1 CONNECTED : N LABEL: SENSOR_1 UNITS: ___ 4 mA: -999.9 20 mA: +999.9 OFFSET: +000.0 ALARM/EVENT: AL LATCHED: N LOW SETPT: -950.0 HIGH SETPT: +950.0 SENSOR DELAY: 00:01

See Section

9.5

MAP INPUT TO OUTPUT MAP SENSOR TO OUTPT

SELECT INPUT INPUT_01 INPUT_02

INPUT_24

SELECT OUTPUTS MAP TO MAIN BOARD MAP TO EXP BOARD

1 OUTPUT MAP

1 2 3 4 5 6 7 8

Y N N N N N N N

or or

1 OUTPUT MAP

0910111213141516

N N N N N N N N

Setup System Info Setup Exp Board

CHANGE PASSWORD CHANGE DATE & TIME SETUP SITE ID CONNECT BATTERY SETUP SERV PH NUM FACTORY DEFAULTS

See Section

9.9

IS THE EXPANSION BOARD CONNECTED? N

↑↓=Y/N ↵ =END

See Section

9.6

SELECT SENSOR SENSOR_1 HIGH STPT SENSOR_1 LOW STPT

. . .

SENSOR_4 LOW STPT

SELECT OUTPUTS MAP TO MAIN BOARD MAP TO EXP BOARD

1H OUTPUT MAP

1 2 3 4 5 6 7 8

Y N N N N N N N

1H OUTPUT MAP

0910111213141516

N N N N N N N N

See Section

9.10

SET PAGER 1 NUMBER SET PAGER 1 PIN

See Figure 15 for details on Setup System Info

9.2 Setup System - Overview

The Setup System screen displays seven options that allow you to configure input and output devices and their relationships, the common alarm, the modem, pagers to be dialed when alarms occur, and a variety of system details, such as login password and system date and time:

System and Control Options

• Setup Input

• Setup Common Alarm

• Setup Sensor

•Setup I/O Matrix

• Setup Output

• Setup Modem & Pagers

• Setup System Info

• Setup Exp Board

9.3 Setup System - Setup Input

The Universal Monitor has eight digital input points that may be configured individually. If the optional Expansion Board is used, an additional 16 digital inputs may also be configured. These inputs may have a wide variety of Liebert or other manufacturers’ equipment connected for monitoring.

To configure a digital input:

• From the Main Menu, use the arrows

Control, then press Enter ↵ (see 9.1 - Login for help).

• Enter your password at the Login screen.

• From the System and Control Menu, use the arrows

Setup System, then press Enter ↵ .

Select a Digital Input to Configure

• From the Setup System Menu, shown at right, use the arrows

choose Setup Input and press Enter ↵ .

• From the Select Input Menu, choose the input you want—for exam-

ple, Input_01—and press Enter ↵ .

Table 21 shows the digital input features you may change, along with the default settings: you may change the name of the input, define it as normally open or closed, and specify it as alarmable or as an event.

• Alarmable inputs may be defined as either Unlatched or Latched.

• Event status allows you to monitor a digital input’s state—and use a change in state to initiate an action through an output, if desired—without triggering an alarm. Events are always Unlatched.

• You may also specify a time delay before the Universal Monitor responds to an alarm or event.

Use the steps following Table 21 to change the default settings for any digital input.

Table 21 Default settings - digital inputs

Feature Default Other Options

LABEL INPUT_01 Any name (up to eight characters) NORM OPEN/CLOSE NO (Normally open) NC (Normally closed) ALARM/EVENT AL (Alarmable) EV (Event) LATCHED NL (Unlatched) / N (No)* L (Latched) / Y (Yes)* DELAY 00:01 (1 second) Any time (in minutes and seconds) from 00:00 to 99:59

* NOTE: Different abbreviations are used to designate a digital input as Latched or Unlatched as shown below.

Settings - Select Input Menu

(see Section 9.3) Unlatched NL (Not Latched) N (No, not latched) Latched L (Latched) Y (Yes, latched)

↑↓ to choose System and

↑↓ to choose

↑↓ to

When configuring an input (see Section 9.3.4)

Setup System Menu

> SETUP INPUT

SETUP COMMON ALARM SETUP SENSOR SETUP I/O MATRIX ↑↓=NEXT ↵ =SELECT

SETUP OUTPUT SETUP MODEM&PAGERS SETUP SYSTEM INFO SETUP EXP BOARD

Select Input Menu

SELECT INPUT

> INPUT_01 NO-AL-NL

INPUT_02 NO-AL-NL ↑↓=NEXT ↵ =SELECT

INPUT_03 NO-AL-NL INPUT_04 NO-AL-NL INPUT_05 NO-AL-NL INPUT_06 NO-AL-NL INPUT_07 NO-AL-NL INPUT_08 NO-AL-NL INPUT_09 NO-AL-NL INPUT_10 NO-AL-NL INPUT_11 NO-AL-NL INPUT_12 NO-AL-NL INPUT_13 NO-AL-NL INPUT_14 NO-AL-NL INPUT_15 NO-AL-NL INPUT_16 NO-AL-NL INPUT_17 NO-AL-NL INPUT_18 NO-AL-NL INPUT_19 NO-AL-NL INPUT_20 NO-AL-NL INPUT_21 NO-AL-NL INPUT_22 NO-AL-NL INPUT_23 NO-AL-NL INPUT_24 NO-AL-NL

NOTE: INPUT_09 - INPUT_24 for optional Expansion Board

System and Control Options

9.3.1 Change Label (Name of Input)

Each input has a default label (Input_01, Input_02, etc.) that you may change to a more descriptive name for ease in recognizing alarms and events associated with the input. The label may consist of up to eight characters (see Table 20 for valid characters).

• From the Setup Input Menu, choose Label for the selected input—Label: Input_01 in the example at right—and press Enter ↵ .

• To change the input’s label, which may consist of up to eight characters:

• Use the arrows

↑↓ to choose a character.

• Press Enter ↵ to advance to the next character position.

• When finished, press Enter ↵ again.

9.3.2 Define Input as Normally Open or Normally Closed

Each input may be set up as Normally Open (NO) or Normally Closed (NC). The default setting for all input points is NO (Normally Open).

If you require an input to be a supervised point, define the input as Normally Closed (NC).

• From the Setup Input Menu, choose Norm Open/Close, as shown at right, and press Enter ↵ .

• To change the normal state for this input, use the arrows choose NO (Normally Open) or NC (Normally Closed), then press Enter ↵ .

↑↓ to

Setup Input Menu

SETUP INPUT_01

> LABEL: INPUT_01

NORM OPEN/CLOSE: NO ALARM/EVENT: AL ↑↓=NEXT ↵ =SELECT

LATCHED: N DELAY: 00:01

Change Label

CHANGE LABEL

INPUT_01

↑↓=SELECT ↵=NEXT/END

Setup Input Menu

SETUP INPUT_01

LABEL: INPUT_01

> NORM OPEN/CLOSE: NO

ALARM/EVENT: AL ↑↓=NEXT ↵ =SELECT

LATCHED: N DELAY: 00:01

Normally Open / Closed

IS INPUT NORMALLY OPENED OR CLOSED? NO

9.3.3 Define Input as Alarmable or Event

Each digital input may be defined as Alarmable (AL) or as an Event (EV).

• For a digital input defined as alarmable, the following alarm reactions occur when the status of the monitored input device changes: the LCD flashes, the audible horn sounds, configured pager numbers will be notified and a record is entered in the Alarm Log.

• For a digital input defined as an event, the status change is recorded in the Event Log.

By default, all digital inputs are set up as AL (Alarmable).

• From the Setup Input Menu, choose Alarm/Event, as shown at right, and press Enter ↵ .

• To change the type of digital input, use the arrows

AL (Alarmable) or EV (Event), then press Enter ↵ .

↑↓=NO/NC ↵ =END

Setup Input Menu

SETUP INPUT_01 LABEL: INPUT_01 NORM OPEN/CLOSE: NO

> ALARM/EVENT: AL

↑↓=NEXT ↵ =SELECT LATCHED: N

DELAY: 00:01

Alarmable / Event

IS INPUT AN ALARM OR EVENT? AL

↑↓=AL/EV ↵ =END

↑↓ to choose

System and Control Options

9.3.4 Set Up Alarmable Inputs in Latched or Unlatched Mode

Alarmable input points may be set up in Latched mode (Y), which requires the user to clear the Universal Monitor alarms after an alarm has occurred, or Unlatched mode (N), in which alarms will automatically clear after a return-to-normal state. The default setting for alarmable inputs is N (Unlatched). Any input defined as an event is automatically Unlatched.

A digital input defined as Latched does not reset automatically after an alarm. It will remain in the triggered position even after the moni- tored device returns to normal. After an alarm, the user must manually reset Latched inputs, as described in 9.12.1 - Clear Active Alarms. This also means that any digital outputs linked to a Latched digital input will remain triggered until the input is manually reset.

A digital input defined as Unlatched will automatically track the status of the monitored device. No action by the user is required.

• From the Setup Input Menu, choose Latched, as shown above

right, and press Enter ↵ .

• To change this feature, use the arrows

Latched) or N (No - Unlatched), then press Enter ↵ .

NOTE: Only alarmable input points may be set up as Latched. If you attempt to set up an event as Latched, the message shown at right appears. Press the ESC key to return to the previous screen to continue configuring the digital input.

↑↓ to choose Y (Yes -

Setup Input Menu

SETUP INPUT_01 LABEL: INPUT_01 NORM OPEN/CLOSE: NO ALARM/EVENT: AL ↑↓=NEXT ↵ =SELECT

> LATCHED: N

DELAY: 00:01

Latched / Unlatched

IS ALARM LATCHED? N

↑↓=Y/N ↵ =END

Message (if input has been defined as an event)

LATCH NOT ALLOWED WHEN IN EVENT MODE

The only way to reset latched alarms is by clearing active alarms. This step is required to return latched points to their normal state. For details, see 9.12.1 - Clear Active Alarms.

9.3.5 Set Up Delay Time

Each input may be set up with a specified time delay between the occurrence of an alarm or event—a monitored device changes state— and any response by the Universal Monitor. This feature can prevent needless responses to transient conditions.

This delay is the amount of time that must elapse before the Universal Monitor acknowledges the change of state in the monitored device and takes any further action, such as dialing configured pagers. The default time delay is 1 second (displayed as 00 MIN : 01 SEC).

The time delay applies only when a monitored device changes from its normal state—for example, the Universal Monitor detects a closed contact that is defined as Normally Open.

When the monitored device returns to its normal state, the Universal Monitor acknowledges the change of state immediately.

• From the Setup Input Menu, choose Delay, as shown at right, and

press Enter ↵ .

• To change the time delay in minutes and seconds (in the range of 00:00 to 99:59):

• For minutes (MIN), press and hold one of the arrow keys 00-99.

• Press Enter ↵ to advance to seconds (SEC).

• For seconds (SEC), press and hold one of the arrow keys

• When finished, press Enter ↵ again.

ESC=BACK

Setup Input Menu

SETUP INPUT_01 LABEL: INPUT_01 NORM OPEN/CLOSE: NO ALARM/EVENT: AL ↑↓=NEXT ↵ =SELECT

LATCHED: N

DELAY: 00:01

Delay Time

DELAY TIME BEFORE TRIGGER?

MIN : 01 SEC

↑↓=SELECT

↑↓ scroll through the numbers

↑↓ scroll through the numbers 00-59.

↵ =NEXT/END

9.4 Setup System - Setup Common Alarm

The audible alarm sounds after the Universal Monitor detects an alarm condition in any input that has been defined as alarmable, including digital and analog sensor inputs. Once the alarm is silenced, there are two options:

• By default, the common alarm remains energized until the input alarm is cleared.

• You may change this setting to de-energize the common alarm automatically once the alarm is silenced.

You might want to reset the common alarm with silence if an external alarm—for example, a horn—is connected to the common alarm output contacts.

You might not want to reset the common alarm contacts (let contacts reflect/track alarms) and simply silence the audible horn.

System and Control Options

To change the common alarm setting:

• From the Main Menu, use the arrows

↑↓ to choose System and

Control, then press Enter ↵ (see 9.1 - Login for help).

• Enter your password at the Login screen.

• From the System and Control Menu, use the arrows

↑↓ to choose

Setup System, then press Enter ↵ .

Change to Reset (Y) or Not Reset (N)

• From the Setup System Menu, shown at right, use the arrows to

choose Setup Common Alarm and press Enter ↵ .

• By default, the common alarm is set up not to reset automatically when the alarm is silenced (N). To change this setting, use the arrows

↑↓ to choose Y (Yes - reset with silence) or N (No - not

reset), then press Enter ↵ .

Setup System Menu

SETUP INPUT

> SETUP COMMON ALARM

SETUP SENSOR SETUP I/O MATRIX ↑↓=NEXT ↵ =SELECT

SETUP OUTPUT SETUP MODEM&PAGERS SETUP SYSTEM INFO SETUP EXP BOARD

↑↓

Reset Common Alarm

RESET COMMON ALARM WITH SILENCE? N

↑↓=Y/N ↵=END

9.5 Setup System - Setup Sensor

The Universal Monitor has four analog sensor input points that may be configured individually. The panel monitors connected equipment for any 4-20 mA input—for example, temperature and humidity.

System and Control Options

To configure a sensor:

• From the Main Menu, use the arrows

↑↓ to choose System and

Control, then press Enter ↵ (see 9.1 - Login for help).

• Enter your password at the Login screen.

• From the System and Control Menu, use the arrows

↑↓ to choose

Setup System, then press Enter ↵ .

Select a Sensor to Configure

• From the Setup System Menu, shown at right, use the arrows to

choose Setup Sensor and press Enter ↵ .

• From the Select Sensor Menu, choose the sensor you want—for example, Sensor_1—and press Enter ↵ .

Table 22 shows sensor features that may be changed, along with the default settings. By default, sensor inputs are not connected.

To activate a sensor input, you must specify it as connected and enter

Setup System Menu

SETUP INPUT SETUP COMMON ALARM

> SETUP SENSOR

SETUP I/O MATRIX ↑↓=NEXT ↵ =SELECT

SETUP OUTPUT SETUP MODEM&PAGERS SETUP SYSTEM INFO SETUP EXP BOARD

↑↓

Select Sensor Menu

SELECT SENSOR

> SENSOR_1 +80.00 DEG

SENSOR_2 ------ DEG ↑↓=NEXT ↵ =SELECT

SENSOR_3 SENSOR_4 +79.50 RH

corresponding values for 4 and 20 mA, as well as high and low setpoints. Other features that may be altered include the name of the sensor, the abbreviation for the units, and defining the sensor as alarmable or as an event.

• Alarmable sensors may be Latched (Y) or Unlatched (N).

• Event status allows you to monitor a sensor’s high and low setpoints—and use those setpoints to change the status of an output, if desired—without triggering an alarm. Events are always Unlatched.

• You may also specify a time delay before the Universal Monitor responds to an alarm or event.

Use the steps following Table 22 to change the default settings for any analog sensor input.

Table 22 Default settings - analog sensor inputs

Feature Default Other Options

CONNECTED* N (Not connected)* Y (Connected)**

LABEL SENSOR_1 Any name (up to eight characters)

UNITS Blank Any units (up to three characters)

4 mA -999.9 Can define up to two decimal places—for example, -99.99

20 mA +999.9 Can define up to two decimal places—for example, +99.99

OFFSET +000.0 Can define up to two decimal places—for example, +00.00

ALARM/EVENT AL (Alarmable) EV (Event)

LATCHED N (Unlatched) Y (Latched)

LOW SETPT -0999.9 Can define up to two decimal places—for example, -999.99

HIGH SETPT +0999.9 Can define up to two decimal places—for example, +999.99

SENSOR DELAY 00:01 (1 second) Any time (in minutes and seconds) from 00:00 to 99:59

* If a sensor is configured as N (Not connected), the display will show an empty reading (blank spaces). ** If a sensor is configured as Y (Connected) and is functioning properly, the display will show a reading. If the

connected sensor is not functioning properly, the display will show dashes (------) indicating a problem.

System and Control Options

9.5.1 Identify the Sensor as Connected

To make use of an analog sensor, you must specify it as Connected (Y). By default, analog sensors are Not connected (N).

• From the Setup Sensor Menu, choose Connected, as shown at right, and press Enter ↵ .

• To change this feature, use the arrows nected) or N (No - Not connected), then press Enter ↵ .

9.5.2 Change Sensor Label (Name)

Each sensor has a default label (Sensor_1, Sensor_2, etc.) that you may change to a more descriptive name. The label may consist of up to eight characters (see Table 20 for valid characters).

• From the Setup Sensor Menu, choose Label for the selected sensor—Label: Sensor_1 in the example—and press Enter ↵ .

• To change the sensor’s label, which may consist of up to eight characters:

• Use the arrows

• Press Enter ↵ to advance to the next character position.

• When finished, press Enter ↵ again.

↑↓ to choose a character.

↑↓ to choose Y (Yes - Con-

Setup Sensor Menu

SETUP SENSOR_1

> CONNECTED : N

LABEL: SENSOR_1 ↑↓=NEXT ↵ =SELECT

UNITS: ___ 4 mA: -999.9 20 mA: +999.9 OFFSET: +000.0 ALARM/EVENT: AL LATCHED: N LOW SETPT: -0999.9 HIGH SETPT: +0999.9 SENSOR DELAY: 00:01

Sensor Connected

IS THE SENSOR CONNECTED? N

↑↓=Y/N ↵ =END

Setup Sensor Menu

SETUP SENSOR_1

CONNECTED : Y

> LABEL: SENSOR_1

↑↓=NEXT ↵ =SELECT UNITS: ___

4 mA: -999.9 20 mA: +999.9 OFFSET: +000.0 ALARM/EVENT: AL LATCHED: N LOW SETPT: -0999.9 HIGH SETPT: +0999.9 SENSOR DELAY: 00:01

9.5.3 Change Units Label

For each sensor, you may use a three-character label to specify measurement units, such as DEG (see Table 20 for valid characters).

• From the Setup Sensor Menu, choose Units for the selected sensor and press Enter ↵ .

• To enter the units label, which may consist of up to three characters:

• Use the arrows

• Press Enter ↵ to advance to the next character position.

• When finished, press Enter ↵ again.

↑↓ to choose a character.

Change Sensor Label

CHANGE SENSOR LABEL

LABEL: ROOM TMP ↑↓=SELECT ↵=END

Setup Sensor Menu

SETUP SENSOR_1 CONNECTED : Y LABEL: ROOM_TMP ↑↓=NEXT ↵ =SELECT

> UNITS: ___

4 mA: -999.9 20 mA: +999.9 OFFSET: +000.0 ALARM/EVENT: AL LATCHED: N LOW SETPT: -0999.9 HIGH SETPT: +0999.9 SENSOR DELAY: 00:01

Change Units Label

CHANGE UNITS LABEL

UNITS: DEG ↑↓=SELECT ↵=NEXT/END

System and Control Options

9.5.4 Change 4 mA Value

For the 4 mA value, enter the smallest value for the range of the sensor—for example, 50°F for a temperature sensor with a range of 50°F to 90°F.

The default value for each sensor is -999.9. Values that can be entered range from -999.9 to +999.9.

To enter a new value:

• From the Setup Sensor Menu, choose 4mA for the selected sensor

and press Enter ↵ .

• To change the 4 mA value:

• Use the arrows

• Press Enter ↵ to advance to the next character position.

• When finished, press Enter ↵ again.

9.5.5 Change 20 mA Value

For the 20 mA value, enter the largest value for the range of the sensor—for example, 90°F for a temperature sensor with a range of 50°F to 90°F.

The default value for each sensor is +999.9. Values that can be entered range from -999.9 to +999.9.

To enter a new value:

• From the Setup Sensor Menu, choose 20 mA for the selected sen-

sor and press Enter ↵ .

• To change the 20 mA value:

• Use the arrows

• Press Enter ↵ to advance to the next character position.

• When finished, press Enter ↵ again.

↑↓ to choose a character.

Setup Sensor Menu

SETUP SENSOR_1 CONNECTED : Y LABEL: ROOM_TMP ↑↓=NEXT ↵ =SELECT

UNITS: DEG

> 4 mA: -999.9

20 mA: +999.9 OFFSET: +000.0 ALARM/EVENT: AL LATCHED: N LOW SETPT: -0999.9 HIGH SETPT: +0999.9 SENSOR DELAY: 00:01

Change 4 mA Value

CHANGE 4 mA VALUE

4 mA: +050.0 ↑↓=SELECT ↵=NEXT/END

Setup Sensor Menu

SETUP SENSOR_1 CONNECTED : Y LABEL: ROOM_TMP ↑↓=NEXT ↵ =SELECT

UNITS: DEG 4 mA: +050.0

> 20 mA: +999.9

OFFSET: +000.0 ALARM/EVENT: AL LATCHED: N LOW SETPT: -0999.9 HIGH SETPT: +0999.9 SENSOR DELAY: 00:01

Change 20 mA Value

CHANGE 20 mA VALUE

9.5.6 Change Offset Value

For the Offset value, enter an adjustment factor—for example, if the sensor reading shows 70°F when the actual temperature is 75°F, the offset might be 5°F.

The default Offset value for each sensor is +000.0. Values that can be entered range from -999.9 to +999.9.

To enter a new value:

• From the Setup Sensor Menu, choose Offset for the selected sensor

and press Enter ↵ .

• To change the Offset value:

• Use the arrows

• Press Enter ↵ to advance to the next character position.

• When finished, press Enter ↵ again.

↑↓ to choose a character.

20 mA: +090.0 ↑↓=SELECT ↵=NEXT/END

Setup Sensor Menu

SETUP SENSOR_1 CONNECTED : Y LABEL: ROOM_TMP ↑↓=NEXT ↵ =SELECT

UNITS: DEG 4 mA: +050.0 20 mA: +090.0

> OFFSET: +000.0

ALARM/EVENT: AL LATCHED: N LOW SETPT: -0999.9 HIGH SETPT: +0999.9 SENSOR DELAY: 00:01

Change Offset Value

CHANGE OFFSET VALUE

OFFSET: +005.0 ↑↓=SELECT ↵=NEXT/END

System and Control Options

9.5.7 Define Sensor as Alarmable or Event

Each sensor may be defined as Alarmable (AL) or as an Event (EV).

• For a sensor defined as alarmable, the following alarm reactions occur when the high-setpoint threshold is crossed: the LCD flashes, the audible horn sounds, configured pager numbers will be notified and a record is entered in the Alarm Log.

• For a sensor defined as an event, the high-setpoint occurrence is recorded in the Event Log.

By default, all sensors are set up as AL (Alarmable).

• From the Setup Sensor Menu, choose Alarm/Event, as shown at right, and press Enter ↵ .

• To change the type of sensor, use the arrows

↑↓ to choose

AL (Alarmable) or EV (Event), then press Enter ↵ .

9.5.8 Set Up Alarmable Sensors in Latched or Unlatched Mode

Alarmable sensor points may be set up in Latched mode (Y), requiring the user to clear the Universal Monitor alarms after an alarm has occurred, or Unlatched mode (N), meaning that alarms will automatically clear after a return-to-normal state. The default setting for alarmable sensors is N (Unlatched). Any sensor defined as an event is automatically Unlatched.

A sensor defined as Latched does not reset automatically after an alarm. It will remain in the triggered position even after the monitored sensor returns to normal. After an alarm, the user must manually reset Latched sensors, as described in 9.12.1 - Clear Active Alarms. This also means that any digital outputs linked to a Latched sensor will remain triggered until the sensor is manually reset.

A sensor defined as Unlatched will automatically track the status of the monitored sensor. No action by the user is required.

• From the Setup Sensor Menu, choose Latched, as shown at right, and press Enter ↵ .

• To change this feature, use the arrows Latched) or N (No - Unlatched), then press Enter ↵ .

NOTE: Only alarmable sensors may be set up as Latched. If you attempt to set up an event as Latched, the message shown at right appears. Press the ESC key to return to the previous screen to continue configuring the digital input.

↑↓ to choose Y (Yes -

Setup Sensor Menu

SETUP SENSOR_1 CONNECTED : Y LABEL: ROOM_TMP ↑↓=NEXT ↵ =SELECT

UNITS: DEG 4 mA: +050.0 20 mA: +090.0 OFFSET: +005.0

> ALARM/EVENT: AL

LATCHED: N LOW SETPT: -0999.9 HIGH SETPT: +0999.9 SENSOR DELAY: 00:01

Alarmable / Event

IS SENSOR AN ALARM OR EVENT? AL

↑↓=AL/EV ↵ =END

Setup Sensor Menu

SETUP SENSOR_1 CONNECTED : Y LABEL: ROOM_TMP ↑↓=NEXT ↵ =SELECT

UNITS: DEG 4 mA: +050.0 20 mA: +090.0 OFFSET: +005.0 ALARM/EVENT: AL

> LATCHED: N

LOW SETPT: -0999.9 HIGH SETPT: +0999.9 SENSOR DELAY: 00:01

Latched / Unlatched

IS ALARM LATCHED? N

↑↓=Y/N ↵=END

Message (if sensor has been defined as an event)

LATCH NOT ALLOWED WHEN IN EVENT MODE

The only way to reset latched alarms is by clearing active alarms. This step is required to return latched points to their normal state. For details, see 9.12.1 - Clear Active Alarms.

ESC=BACK

System and Control Options

9.5.9 Change Low Setpoint

The Low Setpoint value is typically above the 4 mA value for the sensor. For example, if the 4 mA value is 50°F, the Low Setpoint might be 60°F. When the sensor crosses below this value, an alarm or event will occur, depending on the sensor configuration.

The default Low Setpoint for each sensor is -950.0. Values that can be entered range from:

• the 4 mA value + the Offset value (in the example, 50+5=55)

• the 20 mA value + the Offset value (in the example, 90+ 5 =95)

To determine these values, see 9.5.4 - Change 4 mA Value, 9.5.5 - Change 20 mA Value and 9.5.6 - Change Offset Value.

To enter a new value:

• From the Setup Sensor Menu, choose Low Setpt for the selected

sensor and press Enter ↵ .

• To change the Low Setpoint:

• Use the arrows

• Press Enter ↵ to advance to the next character position.

• When finished, press Enter ↵ again.

Setup Sensor Menu

SETUP SENSOR_1 CONNECTED : Y LABEL: ROOM_TMP ↑↓=NEXT ↵ =SELECT

UNITS: DEG 4 mA: +050.0 20 mA: +090.0 OFFSET: +005.0 ALARM/EVENT: AL LATCHED: N

> LOW SETPT: +0055.0

HIGH SETPT: +0999.9 SENSOR DELAY: 00:01

Change Low Setpoint

CHANGE LOW SETPOINT

LOW SETPT: +0060.0

↑↓=SELECT ↵=NEXT/END

↑↓ to choose a character.

9.5.10 Change High Setpoint

The High Setpoint value is typically below the 20 mA value for the sensor. For example, if the 20 mA value is 90°F, the High Setpoint might be 85°F. When the sensor crosses above this value, an alarm or event will occur, depending on the sensor configuration.

The default High Setpoint for each sensor is +950.0. Values that can be entered range from:

• the 4 mA value + the Offset value (in the example, 50+5=55)

• the 20 mA value + the Offset value (in the example, 90+ 5 =95)

To determine these values, see 9.5.4 - Change 4 mA Value, 9.5.5 - Change 20 mA Value and 9.5.6 - Change Offset Value.

To enter a new value:

• From the Setup Sensor Menu, choose High Setpt for the selected

sensor and press Enter ↵ .

•To change the High Setpoint:

• Use the arrows

• Press Enter ↵ to advance to the next character position.

• When finished, press Enter ↵ again.

↑↓ to choose a character.

Setup Sensor Menu

SETUP SENSOR_1 CONNECTED : Y LABEL: ROOM_TMP ↑↓=NEXT ↵ =SELECT

UNITS: DEG 4 mA: +050.0 20 mA: +090.0 OFFSET: +005.0 ALARM/EVENT: AL LATCHED: N LOW SETPT: +0060.0

> HIGH SETPT: +0095.0

SENSOR DELAY: 00:01

Change High Setpoint

CHANGE HIGH SETPOINT

HIGH SETPT: +0085.0

↑↓=SELECT

↵ =NEXT/END

System and Control Options

9.5.11 Set Up Delay Time

Each sensor may be set up with a specified time delay between the triggering of a high or low setpoint—a monitored sensor crosses the high or low setpoint threshold—and any response by the Universal Monitor. This feature can prevent transient conditions from prompting unnecessary responses.

This delay is the amount of time that must elapse before the Universal Monitor acknowledges the change in the monitored sensor and takes any further action, such as dialing configured pagers. The default time delay is 1 second (displayed as 00 MIN : 01 SEC).

The time delay applies to the triggering of a high or low setpoint and also after the monitored sensor returns to its normal state. When the monitored device returns to its normal state, the specified time delay must elapse before the Universal Monitor acknowledges the return-tonormal condition.

• From the Setup Sensor Menu, choose Sensor Delay, as shown at

right, and press Enter ↵ .

• To change the time delay in minutes and seconds (in the range of 00:00 to 99:59):

• For minutes (MIN), press and hold one of the arrow keys 00-99.

• Press Enter ↵ to advance to seconds (SEC).

• For seconds (SEC), press and hold one of the arrow keys

Setup Sensor Menu

SETUP SENSOR_1 CONNECTED : Y LABEL: ROOM_TMP ↑↓=NEXT ↵ =SELECT

UNITS: DEG 4 mA: +050.0 20 mA: +090.0 OFFSET: +005.0 ALARM/EVENT: AL LATCHED: N LOW SETPT: +055.00 HIGH SETPT: +085.00

SENSOR DELAY: 00:01

Delay Time

DELAY TIME BEFORE TRIGGER?

↑↓=SELECT

↑↓ scroll through the numbers

↑↓ scroll through the numbers 00-59.

MIN : 01 SEC

↵ =NEXT/END

9.6 Setup System - Setup I/O Matrix

The Setup I/O Matrix menu allows you to configure the Universal Monitor’s digital and analog inputs to trigger various actions in any or all of the 16 outputs—eight on the main board and another eight if the optional Expansion Board is used. Each output can be set up to respond to more than one digital or analog input, including the additional 16 inputs available via the optional Expansion Board.

System and Control Options

Almost any mapping combination can be used. For example, you may decide to trigger an action in Output03 when Input_01 goes into alarm, or you might want to generate an action in Output04 when Sensor_1 High Setpoint goes into alarm.

To set up the mapping of inputs to outputs:

• From the Main Menu, use the arrows

Control, then press Enter ↵ (see 9.1 - Login for help).

• Enter your password at the Login screen.

• From the System and Control Menu, use the arrows

Setup System, then press Enter ↵ .

Select Setup I/O Matrix

• From the Setup System Menu, shown at right, use the arrows

choose Setup I/O Matrix and press Enter ↵ .

• Use the following instructions to set up the mapping of each digital input or analog sensor input to each output.

9.6.1 Set Up Mapping for a Digital Input

• Use the arrows ↑↓ to choose Map Input To Output from the Map Input/Sensor Menu, and press Enter ↵ .

• From the Select Input Menu, choose the input you want—for example, Input_01—and press Enter ↵ .

Map Input to a Main Board Output

• From the Select Outputs menu, select Map to Main Board if you want to map the selected input to an output on the Universal Monitor’s main board. These outputs are identified as Outputs 1-8.

• On the Output Map screen, you may map the selected input to any of the eight outputs (1-8)—or to more than one output, if desired. The example at right shows Input_01 mapped to Output03.

To make changes to the mapping:

• If needed, press Enter ↵ to advance to the position directly

below the output.

• Use the arrows ↑↓ to choose Y (Yes - Mapped to this output) or N (No - Not mapped), then press Enter ↵ .

• Press Enter ↵ to advance to the next position where you want to make a change.

• Use the arrows ↑↓ to choose Y (Yes - Mapped to this output) or N (No - Not mapped), then press Enter ↵ .

• When finished, press Enter ↵ again.

↑↓ to choose System and

↑↓ to choose

↑↓ to

Setup System Menu

SETUP INPUT SETUP COMMON ALARM SETUP SENSOR

> SETUP I/O MATRIX

↑↓=NEXT ↵ =SELECT SETUP OUTPUT

SETUP MODEM&PAGERS SETUP SYSTEM INFO SETUP EXP BOARD

Map Input/Sensor Menu

> MAP INPUT TO OUTPUT

MAP SENSOR TO OUTPT

↑↓=NEXT

↵ =SELECT

Select Input

SELECT INPUT

> INPUT_01

INPUT_02 ↑↓=NEXT ↵ =SELECT

INPUT_03 INPUT_04 INPUT_05 INPUT_06 INPUT_07 INPUT_08 INPUT_09 INPUT_10 INPUT_11 INPUT_12 INPUT_13 INPUT_14 INPUT_15 INPUT_16 INPUT_17 INPUT_18 INPUT_19 INPUT_20 INPUT_21 INPUT_22 INPUT_23 INPUT_24

Select Outputs

SELECT OUTPUTS

> MAP TO MAIN BOARD

MAP TO EXP BOARD

↑↓=NEXT

↵ =SELECT

Output Map

1 OUTPUT MAP

1 2 3 4 5 6 7 8 N

N Y N N N N N

↑↓=Y/N ↵ =NEXT/END

System and Control Options

Map Input to Expansion Board Output

• From the Select Outputs menu, select Map to Exp Board if you want to map the selected input to an output on the optional Expansion Board. These outputs are identified as Outputs 9-16.

• On the Output Map screen, you may map the selected input to any of the eight outputs (9-16)—or to more than one output, if desired. The example at right shows Input_01 mapped to Output10.

To make changes to the mapping:

• If needed, press Enter ↵ to advance to the position directly

below the output.

• Use the arrows ↑↓ to choose Y (Yes - Mapped to this output) or N (No - Not mapped), then press Enter ↵ .

• Press Enter ↵ to advance to the next position where you want to make a change.

• Use the arrows ↑↓ to choose Y (Yes - Mapped to this output) or N (No - Not mapped), then press Enter ↵ .

• When finished, press Enter ↵ again.

Select Outputs

SELECT OUTPUTS

MAP TO MAIN BOARD

> MAP TO EXP BOARD

↑↓=NEXT

Output Map

1 OUTPUT MAP

0910111213141516

Y N N N N N N

↑↓=Y/N ↵ =NEXT/END

Default Mappings - Digital Inputs to Outputs

Table 23 shows the default mapping of digital inputs to digital outputs.

Table 23 Default mapping of digital inputs to digital outputs

Digital input By default, mapped to digital output:

Input_01 Output01

Input_02 Output02

Input_03 Output03

Input_04 Output04

Input_05 Output05

Input_06 Output06

Input_07 Output07

Input_08 Output08

NOTE: By default, no Expansion Board inputs are mapped to any outputs.

↵ =SELECT

System and Control Options

9.6.2 Set Up Mapping for an Analog Sensor Input

• Use the arrows ↑↓ to choose Map Sensor To Outpt from the Map

Input/Sensor Menu, and press Enter ↵ .

• From the Select Sensor Menu, choose the input you want—for

example, Sensor_1 High Stpt—and press Enter ↵ .

Map Sensor to Main Board Output

• From the Select Outputs menu, select Map to Main Board if you want to map the selected sensor to an output on the Universal Monitor main board. These outputs are identified as Outputs 1-8.

• On the Output Map screen, you may map the selected sensor to any of the eight outputs (1-8)—or to more than one output, if desired. The example at right shows Sensor_1 High Stpt mapped to Output04.

To make changes to the mapping:

• If needed, press Enter ↵ to advance to the position directly

below the output.

• Use the arrows ↑↓ to choose Y (Yes - Mapped to this output) or N (No - Not mapped), then press Enter ↵ .

• Press Enter ↵ to advance to the next position where you want to make a change.

• Use the arrows ↑↓ to choose Y (Yes - Mapped to this output) or N (No - Not mapped), then press Enter ↵ .

• When finished, press Enter ↵ again.

Map Sensor to Expansion Board Output

• From the Select Outputs menu, select Map to Exp Board if you want to map the selected sensor to an output on the optional Expansion Board. These outputs are identified as Outputs 9-16.

• On the Output Map screen, you may map the selected sensor to any of the eight outputs (9-16)—or to more than one output, if desired. The example at right shows Sensor_1 High Stpt mapped to Output11.

To make changes to the mapping:

• If needed, press Enter ↵ to advance to the position directly

below the output.

• Use the arrows ↑↓ to choose Y (Yes - Mapped to this output) or N (No - Not mapped), then press Enter ↵ .

• Press Enter ↵ to advance to the next position where you want to make a change.

• Use the arrows ↑↓ to choose Y (Yes - Mapped to this output) or N (No - Not mapped), then press Enter ↵ .

• When finished, press Enter ↵ again.

Map Input/Sensor Menu

MAP INPUT TO OUTPUT

> MAP SENSOR TO OUTPT

↑↓=NEXT

↵ =SELECT

Select Sensor

SELECT SENSOR

> SENSOR_1 HIGH STPT

SENSOR_1 LOW STPT ↑↓=NEXT ↵ =SELECT

SENSOR_2 HIGH STPT SENSOR_2 LOW STPT SENSOR_3 HIGH STPT SENSOR_3 LOW STPT SENSOR_4 HIGH STPT SENSOR_4 LOW STPT

Select Outputs

SELECT OUTPUTS

> MAP TO MAIN BOARD

MAP TO EXP BOARD

↑↓=NEXT

↵ =SELECT

Output Map

1H OUTPUT MAP

1 2 3 4 5 6 7 8 N

N N Y N N N N

↑↓=Y/N ↵ =NEXT/END

Select Outputs

SELECT OUTPUTS

MAP TO MAIN BOARD

> MAP TO EXP BOARD

↑↓=NEXT

↵ =SELECT

Output Map

1H OUTPUT MAP

0910111213141516

N Y N N N N N

↑↓=Y/N ↵ =NEXT/END

Default Mappings - Analog Inputs to Outputs

By default, analog inputs are not mapped to any digital output, as shown in Table 24.

Table 24 Default mapping of analog inputs to digital outputs

Analog input By default, mapped to digital output:

Sensor_1 (none)

Sensor_2 (none)

Sensor_3 (none)

Sensor_4 (none)

System and Control Options

9.7 Setup System - Setup Output

The Universal Monitor has eight outputs that may be configured individually. If the optional Expansion Board is used, its additional eight digital outputs may be renamed. The outputs may have a wide variety of Liebert or other manufacturers’ equipment connected for configured responses to input alarms and events.

To configure an output:

• From the Main Menu, use the arrows

Control, then press Enter ↵ (see 9.1 - Login for help).

• Enter your password at the Login screen.

• From the System and Control Menu, use the arrows

Setup System, then press Enter ↵ .

Select an Output to Configure

• From the Setup System Menu, shown at right, use the arrows to

choose Setup Output and press Enter ↵ .

• From the Select Output Menu, choose the output you want—for example, Output01—and press Enter ↵ .

Table 25 shows digital output features and default settings. You may change the name of any output. In addition, the Universal Monitor’s eight outputs may be defined as normally open or closed.

Use the steps following Table 25 to change the default settings for any digital output.

Table 25 Default settings - digital outputs

Feature Default Other Options

LABEL OUTPUT01

NORM OPEN/CLOSE

(Main board only)

NO (Normally open) NC (Normally closed)

↑↓ to choose System and

↑↓ to choose

↑↓

Any name (up to eight characters)

Setup System Menu

SETUP INPUT SETUP COMMON ALARM SETUP SENSOR SETUP I/O MATRIX ↑↓=NEXT ↵ =SELECT

> SETUP OUTPUT

SETUP MODEM&PAGERS SETUP SYSTEM INFO SETUP EXP BOARD

Select Output Menu

SELECT OUTPUT

> OUTPUT01 NO

OUTPUT02 NO ↑↓=NEXT ↵ =SELECT

OUTPUT03 NO OUTPUT04 NO OUTPUT05 NO OUTPUT06 NO OUTPUT07 NO OUTPUT08 NO OUTPUT09 NO OUTPUT10 NO OUTPUT11 NO OUTPUT12 NO OUTPUT13 NO OUTPUT14 NO OUTPUT15 NO OUTPUT16 NO

NOTE: OUTPUT09- OUTPUT16 for optional Expansion Board

9.7.1 Change Label (Name of Output)

Each output has a default label (Output01, Output02, etc.) that you may change to a more descriptive name. The label may consist of up to eight characters (see Table 20 for valid characters).

• From the Setup Output Menu, as shown at right, use the arrows

↑↓ to choose Change Label for the selected output and

press Enter ↵ .

• To change the output’s label, which may consist of up to eight characters:

• Use the arrows

↑↓ to choose a character.

• Press Enter ↵ to advance to the next character position.

• When finished, press Enter ↵ again.

9.7.2 Define Main Board Output as Normally Open / Closed

Each output may be set up as Normally Open (NO) or Normally Closed (NC). The default setting for all output points is NO (Normally Open).

• From the Setup Output Menu, choose Change State, as shown at right, and press Enter ↵ .

• To change the normal state for this output, use the arrows choose NO (Normally Open) or NC (Normally Closed), then press Enter ↵ .

↑↓ to

Setup Output Menu

> CHANGE LABEL

CHANGE STATE

↑↓=NEXT

↵ =SELECT

Change Label

CHANGE LABEL

LABEL: OUTPUT01 ↑↓=SELECT ↵ =NEXT/END

Setup Output Menu

CHANGE LABEL

> CHANGE STATE

↑↓=NEXT

↵ =SELECT

Change State

SET TO NORMAL OPEN OR NORMAL CLOSE? NO

↑↓=NO/NC ↵ =END

System and Control Options

9.7.3 Set Expansion Board Output by DIP Switch

If you choose Change State from the Setup Output Menu for an Expansion Board output (OUTPUT09-16), the screen displays a message that the state must be set by DIP switch, as shown at right.

Each digital output on the optional Expansion Board has an associated DIP switch that can determine its operation in the event of loss of communication with the Universal Monitor or loss of power.

To configure a digital output jumper for a loss of power:

• Move the switch down to the “OFF” position (factory default) for Normally Open (NO).

• Move the switch up to the “ON” position for Normally Closed (NC).

For more information, see 5.2.3 - Setting the Digital Output DIP Switches.

9.7.4 Configure Main Board Output for Loss of Power (“Fail-Safe”)

Each digital output has an associated jumper that can help prevent undesired effects when the controller board loses power. For example, without the proper fail-safe jumper setting, a loss of power might close a switch that is Normally Open (NO)—perhaps shutting off a fan or closing a valve.

This fail-safe jumper setting is unrelated to configuring an output as Normally Open (NO) or Normally Closed (NC), as described in the previous section, Define Main Board Output as Normally Open / Closed.

To configure a digital output jumper for a loss of power:

Setup Output Menu

CHANGE LABEL

> CHANGE STATE

↑↓=NEXT

↵ =SELECT

Message (if Expansion Board output selected)

SET BY DIPSWITCH

ESC=BACK

• Set the jumper in the “OFF” position (factory default) to make the output Normally Open (NO).

• Set the jumper in the “ON” position to make the output Normally Closed (NC).

For more information, see 4.2.3 - Setting the Digital Output Jumpers.

9.8 Setup System - Setup Modem & Pagers

To use the modem and pager features, be sure to connect the phone line connector to a telephone wall jack using an RJ11 cord, as described in 4.6.2 - Phone Line Connector.

9.8.1 Modem Setup - Initialization String

The Universal Monitor has an on-board modem that offers dial-up access to all LCD functions as well as features available only through the Service Terminal Interface (see A.1 - Comparison of Func- tions: LCD and Service Terminal Interface). The modem also permits remote notification of alarms.

Supported Modem Settings

Supported settings vary for different types of access:

Table 26 Supported modem settings

For: Modem supports:

Dial-up via terminal 9600 baud, no parity, 8 data bits, 1 stop bit

Pager access 9600 baud, even parity, 7 data bits, 1 stop bit and TAPI protocol version 1.8

For calls involving countries that do not support country code B5 (see Table 28):

International dialing

• Modem model MT5600SMI is required (model number is on the modem label).

• +GCI=xx (xx is the country code) must be added to the initialization string (see Step 7 in this section).

System and Control Options

Default Modem Settings

Table 27 shows the default settings for modem options.

Table 27 Default settings - modem

Feature Default Other Options

Any string (up to 40 characters); for international dialing,

Initialization String (Init String) ATS0=1

Enable Modem Diagnostic Messages N (disable) Y (enable)

Modem Dial Prefix ATE0X4DT Any string

Modem Hang Up Delay After a Call 10 seconds Any number (up to 99 seconds)

add +GCI=xx, where xx is the country code (except B5 countries—see Table 28)

Configuring the Modem

To configure the modem:

1. From the Main Menu, use the arrows

Control, then press Enter ↵ (see 9.1 - Login for help).

2. Enter your password at the Login screen.

3. From the System and Control Menu, use the arrows

Setup System, then press Enter ↵ .

↑↓ to choose System and

↑↓ to choose

Setup System Menu

SETUP INPUT SETUP COMMON ALARM SETUP SENSOR SETUP I/O MATRIX ↑↓=NEXT ↵ =SELECT

SETUP OUTPUT

> SETUP MODEM&PAGERS

SETUP SYSTEM INFO SETUP EXP BOARD

System and Control Options

Select Modem Setup

4. From the Setup System Menu, shown at right, use the arrows

choose Setup Modem&Pagers and press Enter ↵ .

5. Use the arrows

↑↓ to choose Setup Modem from the Pagers &

Modem Menu and press Enter ↵ .

6. The Setup Modem Menu displays the initialization string (Init String), which may consist of up to 40 characters (see Table 20 for valid characters). The default Init String is ATS0=1.

↑↓ to

Setup System Menu

SETUP INPUT SETUP COMMON ALARM SETUP SENSOR SETUP I/O MATRIX ↑↓=NEXT ↵ =SELECT

SETUP OUTPUT

> SETUP MODEM&PAGERS

SETUP SYSTEM INFO SETUP EXP BOARD

International Dialing

7. To enable international dialing involving countries that do not support country code B5 (see Table 28), you must add the appropriate country codes to the initialization string using the

Pagers & Modem Menu

SETUP PAGERS

> SETUP MODEM

format:

+GCI=xx

↑↓=NEXT

↵ =SELECT

where xx is the country code. (This also requires the modem model MT5600SMI; the model num-

ber can be found on the modem label.) Note: For countries that support B5, there is no need to add coun-

try codes to the init string.

Setup Modem Menu

ENTER INIT STRING

ATS0=1

↑↓=NEXT

↵ =SELECT

Table 28 Country codes

Country Code* Country Code* Country Code* Country Code*

Argentina 07 Finland FD Italy FD Philippines B5

Australia 09 France FD Japan 00 Portugal FD

Austria FD Germany FD Korea B5 Slovak Republic FD

Belgium FD Greece FD Liechtenstein FD Spain FD

Canada B5 Hong Kong 99 Luxembourg FD Sweden FD

China B5 Hungary FD Mexico B5 Switzerland FD

Cyprus FD Iceland FD Netherlands FD Taiwan FE

Czech Republic FD Indonesia 99 New Zealand 7E United Kingdom FD

Denmark FD Ireland FD Norway FD United States B5

* B5 is the default setting—initialization string +GCI=xx is not needed for these countries

Edit the Init String

8. To enter or edit the Init String:

• Use the arrows

↑↓ to choose a character.

• Press Enter ↵ to advance to the next character position.

• When finished, press Enter ↵ again.

System and Control Options

9.8.2 Modem Setup - Additional Features (Service Terminal Interface only)

The Service Terminal Interface offers four additional options for the modem that are not available through the LCD interface:

• Enter Universal Monitor phone number

• Enable modem diagnostic messages

• Change modem dial prefix

• Change modem hang up delay after a call

To access these options:

• Connect to the Universal Monitor either from a remote computer or through the RS232 port (see A.2 - Connecting to the Service Terminal Interface).

• At the Main Menu, enter 0 (zero—Setup System-Login Required).

• At the Login Menu, enter your password.

• At the Setup Menu, enter 6 (Setup Modem&Pagers).

• At the Setup Modem & Pagers menu, shown below, enter 5 to begin configuration.

Setup Modem & Pagers - Modem Setup (Service Terminal Interface only)

SETUP MODEM&PAGERS

Input pager and modem information

Select pager or modem

1=PAGER NUMBER 1 An "A" is required 2=PAGER NUMBER 2 as 1st character 3=PAGER NUMBER 3 for an alpha pager, 4=PAGER NUMBER 4 an "N" for a numeric 5=MODEM CONFIGURATION pager, and an "M" 6=RETURN TO SETUP MENU for a remote modem. 7=RETURN TO MAIN MENU *******************

SELECT A NUMBER:5

CURRENT NUMBER

*******************

• At the Change Modem Initialization String prompt, you may press Enter to bypass this option (or see 9.8.1 - Modem Setup - Initialization String for instructions on entering the string).

>CHANGE MODEM INITIALIZATION STRING(40 CHARACTERS MAX). >[ATS0=1] >[ >COMMAND SUCCESSFUL

Enter Universal Monitor Phone Number

This entry allows you to store the phone number that must be dialed to access the Universal Monitor for future reference. This has no effect on the Universal Monitor’s modem settings or functionality—it simply places the phone number in an accessible location.

• At the Universal Monitor Phone Number prompt, enter the phone number for the Universal Monitor. The current setting appears in brackets []—nothing has been entered in the following example.

>ENTER UNIVERSAL MONITOR PHONE NUMBER(40 CHARACTERS MAX). >[] >[ >COMMAND SUCCESSFUL

• Press Enter to proceed, or Escape to cancel the entry. If you make a change, a confirmation message appears: “Command Successful.”

System and Control Options

Enable Modem Diagnostic Messages

Enabling modem diagnostics will provide the following additional information about the modem to the computer using the Service Terminal Interface:

Hang-up modem Modem model number No dial tone No carrier Busy No answer Pager checksum error Pager pin number error Error (indicates incorrect phone number, dial prefix or modem initialization string)

For alphanumeric pager failures:

Paging company non answer on 1st Paging company non answer on 2nd Paging company non answer on Last Paging company non answer on Handshake

• At the Enable Modem Diagnostic Messages prompt, enter Y (Yes - enable) or N (No - disable). The current setting appears in brackets—[N] in the following example.

>ENABLE MODEM DIAGNOSTIC MESSAGES-YES(Y) OR NO(N)? >[N] >[ >COMMAND SUCCESSFUL

• Press Enter to proceed, or Escape to cancel the entry. If you make a change, a confirmation message appears: “Command Successful.”

Change Modem Dial Prefix

• At the Change Modem Dial Prefix prompt, enter the prefix to be dialed. The current setting appears in brackets—[ATE0X4DT] in the following example.

>CHANGE MODEM DIAL PREFIX. >[ATE0X4DT] >[ >COMMAND SUCCESSFUL

• For international dialing involving countries that do not support B5 (see Table 28), add country codes to the initialization string using the format +GCI=xx, where xx is the country code. (Note: Also requires MT5600SMI modem; model number is on modem label.)

See 9.8.1 - Modem Setup - Initialization String for more information.

• Press Enter to proceed, or Escape to cancel the entry. If you make a change, a confirmation message appears: “Command Successful.”

Change Modem Hang Up Delay After a Call

• At the Change Modem Hang Up Delay After a Call prompt, enter the number of seconds to delay hanging up after a call. The maximum is 99 seconds. The current setting appears in brackets— [10] in the following example.

>CHANGE MODEM HANG UP DELAY AFTER A CALL(99 SEC MAX). >[10] >[ >COMMAND SUCCESSFUL

• Press Enter to proceed, or Escape to cancel the entry. If you make a change, a confirmation message appears: “Command Successful.”

9.8.3 Pager Setup - Pager Number and PIN

The Universal Monitor may be configured to dial numeric or alphanumeric pagers when an alarm is detected. You may enter up to four pager numbers—all configured pagers will be dialed each time an alarm occurs. For each configured pager, you must enter the pager number to be dialed and the pager’s Personal Identification Number (PIN).

See 10.1 - Universal Monitor Specifications for supported pager settings.

The Universal Monitor can send numeric or alphanumeric messages to supported pagers, as shown in the following example:

System and Control Options

Alphanumeric pager

message example

LIEBERT TEST INPUT_01 ALARM CONTACT CLOSED

2:07 PM 06/09/04 Pager company time stamp

When an alarm is detected, the first pager number is dialed—up to three times, if needed. After a successful page or three dialing attempts, the next pager number is dialed, again with three attempts as needed, and so on for all configured pagers.

Table 29 Pager dialing results

Result of Page Action Message Generated

Successful Universal Monitor dials next configured pager. —

Unsuccessful due to:

Busy signal / no answer / no dial tone

General modem communication problem

No communication with modem (internal hardware problem)

To configure a pager:

• From the Main Menu, use the arrows Control, then press Enter ↵ (see 9.1 - Login for help).

• Enter your password at the Login screen.

• From the System and Control Menu, use the arrows Setup System, then press Enter ↵ .

Select a Pager to Configure

• From the Setup System Menu, shown at right, use the arrows to

choose Setup Modem&Pagers and press Enter ↵ .

• Use the arrows

↑↓ to choose Setup Pagers from the Pagers &

Modem Menu, and press Enter ↵ .

• From the Select Pager Menu, choose the pager number you

Universal Monitor generates message after all three redial attempts have failed, dials next configured pager.

Universal Monitor resets modem, generates message, redials pager up to three more times.

Universal Monitor generates messages, makes no further dialing attempts.

Setup System Menu

SETUP INPUT

↑↓ to choose System and

↑↓ to choose

↑↓

SETUP COMMON ALARM SETUP SENSOR SETUP I/O MATRIX ↑↓=NEXT ↵ =SELECT

SETUP OUTPUT

> SETUP MODEM&PAGERS

SETUP SYSTEM INFO SETUP EXP BOARD

Pagers & Modem Menu

> SETUP PAGERS

SETUP MODEM

↑↓=NEXT

Unsuccessful Page (Event Log)

Modem Reset (Event Log)

Modem Internal Fault

(Active Alarm Report, Alarm History Log)

↵ =SELECT

want—for example, Pager Number 1—and press Enter ↵ .

Select Pager Menu

SELECT PAGER

> PAGER NUMBER 1

PAGER NUMBER 2 ↑↓=NEXT ↵ =SELECT

PAGER NUMBER 3 PAGER NUMBER 4

System and Control Options

Enter a Pager Number

• From the Setup Pager Menu, choose Setup Pager Number for the selected pager—Setup Pager 1 Number in the example at right—and press Enter ↵ .

• See Table 30 for guidelines on entering the pager number, which may consist of up to 40 characters. To enter the pager number:

• Use the arrows

↑↓ to choose a character.

• Press Enter ↵ to advance to the next character position.

• When finished, press Enter ↵ again.

Table 30 Guidelines for dialing pagers

Device type Required entries Example

Numeric

pager

Alphanumeric

pager

Remote

modem

Device type Optional entries Example

All types

of devices

Numeric

pager

The first character must be “N”. N18005551212

The first character must be “A”. A18005551212

The first character must be “M”. M18005551212

Use “9” if needed to access an outside line—place after first character (N, A or M).

Use "W" to wait for a second dial tone before dialing if the phone system has two dial tones (initial tone and a second tone for outside line)—place after “9” (before the number to be dialed).

Use “,” (comma) to pause two seconds. N1,8005551212

Use “#” as the last character to terminate page string if required by paging company.

A918005551212

A9W18005551212

N18005551212 ,,,,1234567#

Setup Pager Menu

> SET PAGER 1 NUMBER

SET PAGER 1 PIN

↑↓=NEXT

↵ =SELECT

Pager # - Numeric

ENTER PAGER 1 NUMBER

N1,8005551212,,,,123 4567#

↑↓=SELECT

↵ =NEXT/END

Pager # - Alphanumeric

ENTER PAGER 1 NUMBER

A9W18005551212

↑↓=SELECT ↵ =NEXT/END

Enter a Pager PIN Number

• From the Setup Pager Menu, choose Setup Pager PIN, as shown for Pager Number 1 in the example at right, and press Enter ↵.

• To enter the pager PIN, which may consist of up to 20 characters (see Table 20 for valid characters):

• Use the arrows

↑↓ to choose a character.

• Press Enter ↵ to advance to the next character position.

• When finished, press Enter ↵ again.

NOTE

For international dialing, you might need to add country codes in the modem initialization string. See 9.8.1 - Modem Setup - Initialization String.

Setup Pager Menu

SET PAGER 1 NUMBER

> SET PAGER 1 PIN

↑↓=NEXT

↵ =SELECT

Enter Pager PIN

ENTER PAGER 1 PIN

01234567891011121314

↑↓=SELECT

↵ =NEXT/END

System and Control Options

9.8.4 Pager Setup - Communications Check (Service Terminal Interface only)

The Service Terminal Interface offers two additional options for pager setup, which are not available through the LCD interface:

• Enable communications check

• Enter time to perform communications check

To access these options:

• Connect to the Universal Monitor either from a remote computer or through the RS232 port (see A.2 - Connecting to the Service Terminal Interface).

• At the Main Menu, enter 0 (zero—Setup System-Login Required).

• At the Login Menu, enter your password.

• At the Setup Menu, enter 6 (Setup Modem&Pagers).

• At the Setup Modem & Pagers menu, shown below, enter a number (1-4) to select a pager.

Setup Modem & Pagers - Pager Setup (Service Terminal Interface only)

SETUP MODEM&PAGERS

Input pager and modem information

Select pager or modem

SELECT A NUMBER:1

CURRENT NUMBER

*******************

• At the Enter Pager Number prompt, you may press Enter to bypass this option (or see 9.8.3 Pager Setup - Pager Number and PIN for instructions on entering the pager number).

>ENTER PAGER NUMBER(40 CHARACTERS MAX). >[] >[ >COMMAND SUCCESSFUL

• At the Enter Pager PIN Number prompt, you may press Enter to bypass this option (or see 9.8.3 Pager Setup - Pager Number and PIN for instructions on entering the pager PIN).

>ENTER PAGER PIN NUMBER (20 CHARACTERS MAX). >[] >[ >COMMAND SUCCESSFUL

System and Control Options

Enable Communications Check

Enabling this function permits a daily communications test between the Universal Monitor and the selected pager. Once each day the Universal Monitor dials the pager at a specified time and sends this message: “UNIVERSAL MONITOR COMM CHECK.” (The time of the test is specified at the next prompt, Enter Time To Perform Communications Check.)

• At the Enable Communications Check prompt, enter Y (Yes - enable) or N (No - disable). The current setting appears in brackets—[N] in the following example.

>ENABLE COMMUNICATIONS CHECK-YES(Y) OR NO(N)? >[N] >[ >COMMAND SUCCESSFUL

• Press Enter to proceed, or Escape to cancel the entry. If you make a change, a confirmation message appears: “Command Successful.”

Enter Time To Perform Communications Check

This function schedules the daily communications test between the Universal Monitor and the selected pager, as described in the previous section.

• At the Enter Time To Perform Communications Check prompt, enter the time to initiate the communications check, using the format HH:MM (hours and minutes in military time), ranging from 00:00 for midnight to 23:59 for 11:59 p.m. The current setting appears in brackets—[00:00] in the following example.

>ENTER TIME TO PERFORM COMMUNICATIONS CHECK(HH:MM). >[00:00] >[ >COMMAND SUCCESSFUL

• Press Enter to proceed, or Escape to cancel the entry. If you make a change, a confirmation message appears: “Command Successful.”

9.9 Setup System - Setup System Info

The Setup System Info options allow users to:

• Change Password—used for access to system setup functions

• Change Date & Time/Automatic Daylight Saving Time—used to set the Universal Monitor’s date and time and to enable automatic time change for Daylight Saving Time

• Setup Site ID—the Universal Monitor’s location to differentiate among sites if more than one Universal Monitor is in use

• Connect Battery—stops the Universal Monitor battery from backing up the panel

• Backup and Upload Configuration File (Service Terminal Interface only)—permits the user to copy the Universal Monitor’s configuration settings and to upload the file to the Universal Monitor

• Setup Serv Ph Num—enables alarm notification to the telephone number entered (in addition to the four pager numbers).

• Restore Defaults—returns the Universal Monitor to its factory settings

• Perform Firmware Update (Service Terminal Interface only)—changes the Universal Monitor’s firmware to newest version

• Initiate Remote Alarm Test (Service Terminal Interface only)—used to test auxiliary alarm

To change any Setup System Info features:

System and Control Options

• From the Main Menu, use the arrows

↑↓ to choose System and

Control, then press Enter ↵ (see 9.1 - Login for help).

• Enter your password at the Login screen.

• From the System and Control Menu, use the arrows Setup System, then press Enter ↵ .

Select Setup System

• From the Setup System Menu, shown at right, use the arrows to

choose Setup System Info and press Enter ↵ .

• Use the steps following Figure 15 to access any of the Setup System Info options.

Figure 15 offers a quick look at the Setup System Info screens available via the LCD interface.

Figure 15 Menu overview - Setup System Info menu

Setup System Info

SETUP SYSTEM INFO CHANGE PASSWORD CHANGE DATE & TIME SETUP SITE ID CONNECT BATTERY SETUP SERV PH NUM FACTORY DEFAULTS

Setup System Info options

Change Password Change Date & Time Setup Site ID

CHANGE PASSWORD

AAAA

See Section

9.9.1

CHANGE DATE & TIME

DAYLIGHT SVG TIME: Y

18-MAY-02 10:56:30

See Section

9.9.2

↑↓ to choose

↑↓

SETUP SITE ID AAAAAAAAAAAAAAAAAAAA AAAAAAAAAAAAAAAAAAAA

Setup System Menu

SETUP INPUT SETUP COMMON ALARM SETUP SENSOR SETUP I/O MATRIX ↑↓=NEXT ↵ =SELECT

SETUP OUTPUT SETUP MODEM&PAGERS

> SETUP SYSTEM INFO

SETUP EXP BOARD

See Section

9.9.3

Connect Battery Setup Serv Ph Num Factory Defaults

IS THE BATTERY CONNECTED? Y

See Section

9.9.4

ENTER PHONE NUMBER

9,,18005551212

See Section

9.9.6

RESTORE ALL DEFAULTS ARE YOU SURE? N

See Section

9.9.8

System and Control Options

9.9.1 Change Password

A password is required to access the Universal Monitor’s system and control options, as described in 9.1 - Login. The password consists of four characters (see Table 20 for valid characters). The default password is AAAA.

Change the Password

To change the password:

• From the Setup System Info Menu, use the arrows

Change Password, then press Enter ↵ .

• To change your password:

• Use the arrows

• Press Enter ↵ to advance to the next character position.

• When finished, press Enter ↵ again.

Reset Password to the Factory Default (“AAAA”)

To reset the password to the factory default of AAAA:

• Locate DIP switch 1 on the unit’s circuit board (see 1.7 - Controller Board Overview) and move all switches to the OFF position (down).

• Move the second switch to the ON position, then to the OFF position.

• Move the seventh switch to the ON position, then to the OFF position.

• Move the eighth switch to the ON position, then to the OFF position.

↑↓ to choose a character.

Setup System Info Menu

SETUP SYSTEM INFO

> CHANGE PASSWORD

CHANGE DATE & TIME ↑↓=NEXT ↵ =SELECT

SETUP SITE ID CONNECT BATTERY SETUP SERV PH NUM FACTORY DEFAULTS

↑↓ to choose

Change Password

CHANGE PASSWORD

AAAA

↑↓=SELECT ↵ =NEXT/END

The password should now be AAAA.

9.9.2 Change Date & Time/Automatic Daylight Saving Time

The Universal Monitor has a built-in real-time clock that is backed up by an encapsulated lithium battery and set up to adjust automatically for daylight saving time twice a year. The Setup System Info menu allows you to change the date or time or automatic adjustment at any time.

To change the daylight saving time setting, date or time:

• From the Setup System Info Menu, use the arrows Change Date & Time, then press Enter ↵ .

• To change the daylight saving time setting:

• To the right of Daylight Svg Time?

use the arrows ↑↓ to

choose Y (Yes - automatically adjust for daylight saving time) or N (No), then press Enter ↵ .

• The format of the date and time is DD-MMM-YY HR:MM:SS. To change the date or time:

• Press Enter ↵ to advance to the next character position you

want to change.

• Use the arrows

Date Day (DD) 0-31

Time Hour (HR) 00-23

↑↓ to choose from available entries:

Month (MMM) JAN-DEC Year (YY) 00-99

Minutes (MM) 00-59 Seconds (SS) 00-59

• Press Enter ↵ to advance to the next character position.

• When finished, press Enter ↵ again.

↑↓ to choose

Setup System Info Menu

SETUP SYSTEM INFO

CHANGE PASSWORD

> CHANGE DATE & TIME

↑↓=NEXT ↵ =SELECT SETUP SITE ID

CONNECT BATTERY SETUP SERV PH NUM FACTORY DEFAULTS

Change Date & Time

CHANGE DATE & TIME

DAYLIGHT SVG TIME: Y

18-MAY-02 10:56:30

↑↓=SELECT ↵ =NEXT/END

System and Control Options

9.9.3 Setup Site ID

You may enter a Site ID to identify the Universal Monitor’s location, using a name that may consist of up to 40 characters (see Table 20 for valid characters). The Site ID will appear with each alarm.

To enter or change the Site ID:

• From the Setup System Info Menu, use the arrows Setup Site ID, then press Enter ↵ .

• To enter a Site ID:

• Use the arrows

• Press Enter ↵ to advance to the next character position.

• If the Site ID is less than 40 characters, you may enter an underscore (_) character to indicate the end of the name.

• When finished, press Enter ↵ again.

9.9.4 Connect Battery

By default, the Universal Monitor checks the battery and sounds an alarm when the power fails, the battery runs low or the battery needs to be checked. The battery’s main purpose is to provide enough power to the modem to notify pagers of a power loss.

NOTE

The battery will continue to power and provide full operation of the Universal Monitor with the exception of powering the analog inputs (sensors). The battery will provide backup for a minimum of 10 minutes.

Using the following procedure to disconnect the battery will disable battery alarm features only. The battery itself will continue to provide backup. If battery backup is not desired, the battery must be unplugged from the circuit board. This can be done by removing the battery leads from the jumpers (see 2.4.3 - Connecting the Battery Pack).

↑↓ to choose a character.

↑↓ to choose

Setup System Info Menu

SETUP SYSTEM INFO CHANGE PASSWORD CHANGE DATE & TIME ↑↓=NEXT ↵ =SELECT

> SETUP SITE ID

CONNECT BATTERY SETUP SERV PH NUM FACTORY DEFAULTS

Setup Site ID

SETUP SITE ID

AAAAAAAAAAAAAAAAAAAA

AAAAAAAAAAAAAAAAAAAA ↑↓=SELECT ↵ =NEXT/END

The default is to connect the battery. However, there may be times that you want to disconnect the battery so that it does not provide backup.

Table 31 shows battery problems that will affect operation.

Table 31 Battery alarms

Result of Battery Action Message Generated

Battery falls below a minimum charge. Battery will not provide battery backup. LOW BATTERY

Battery is connected to the circuit board but not recognized by the circuit board.

Battery is unplugged from the circuit board. Battery will not provide battery backup BATTERY UNPLUGGED

Utility power (24VAC) to the circuit board is too low to power the board.

To connect or disconnect the battery:

• From the Setup System Info Menu, use the arrows

Connect Battery, then press Enter ↵ .

• Use the arrows

↑↓ to choose Y (Yes - the battery is connected) or

N (No - the battery is not connected), then press Enter ↵ .

Battery will not provide battery backup. CHECK BATTERY

Universal Monitor board will not be able to function properly.

LOSS OF POWER

Setup System Info Menu

↑↓ to choose

SETUP SYSTEM INFO CHANGE PASSWORD CHANGE DATE & TIME ↑↓=NEXT ↵ =SELECT

SETUP SITE ID

> CONNECT BATTERY

SETUP SERV PH NUM FACTORY DEFAULTS

Connect Battery

IS THE BATTERY CONNECTED? Y

↑↓=Y/N ↵ =END

System and Control Options

9.9.5 Backup and Upload Configuration File (Service Terminal Interface only)

This operation may be performed only through the Service Terminal Interface. It permits the user to make a copy of the Universal Monitor’s configuration settings and save it as a file on the computer connected through the RS232 port. Should the need arise, the user can upload the configuration file from the computer to the Universal Monitor, instead of re-entering the settings manually.

To access these options:

1. Connect to the Universal Monitor either from a remote computer or through the RS232 port (see A.2 - Connecting to the Service Terminal Interface).

2. At the Main Menu, enter 0 (zero—Setup System-Login Required).

3. At the Login Menu, enter your password.

4. At the Setup Menu, enter 7 (Setup System Information).

5. At the Setup System Information Menu, enter 5 (Backup & Upload Configuration File). The Backup & Upload Configuration File menu appears, shown below:

Backup & Upload Configuration File - Backup (Service Terminal Interface only)

BACKUP AND UPLOAD CONFIGURATION FILE

Backup from panel saves panel configurations Upload to panel restores panel configurations

Select to backup or upload file

1=BACKUP CONFIGURATION FILE 2=UPLOAD CONFIGURATION FILE 3=RETURN TO SETUP SYSTEM INFO MENU 4=RETURN TO SETUP MENU 5=RETURN TO MAIN MENU

SELECT A NUMBER:1

6. Enter 1 to back up the configuration file from the Universal Monitor to the computer and proceed to Step 8,

7. Enter 2 to upload the configuration file from the computer to the Universal Monitor and proceed to Step 13. NOTE: This will replace the current configuration settings in the Universal Monitor with the most recent backup.

System and Control Options

Back Up the Configuration File

8. At the prompt to Initiate a Backup of Configuration File, enter Y (Yes - begin) or N (No - cancel). The current setting appears in brackets—[N] in the following example.

>INITIATE A BACKUP OF CONFIGURATION FILE-YES(Y) OR NO(N)? >[N] >[

NOTE

The following instructions refer to the Microsoft Windows HyperTerminal program. These steps may vary for other communications programs.

9. At the top of the HyperTerminal window, shown below, click on Transfer, then on Receive File.

Enter folder

Select Xmodem

Enter filename for example,

UMconfig.sav

10. In the Receive File window, as shown above:

• In the Use Receiving Protocol box, select Xmodem from the drop-down list.

• Click on the Receive button. (To close the window without backing up the file, click on Close or Cancel.)

11. In the Receive Filename window, enter a name for the file—for example, UMconfig.sav.

12. When the transfer is complete, a confirmation message appears in the Service Terminal Interface window: “Backup Successful.”

System and Control Options

Upload the Configuration File

13. At the prompt to Initiate an Upload of Configuration File, enter Y (Yes - begin) or N (No - cancel). The current setting appears in brackets—[N] in the following example.

>INITIATE AN UPLOAD OF CONFIGURATION FILE-YES(Y) OR NO(N)? >[N] >[

NOTE

The following instructions refer to the Microsoft Windows HyperTerminal program. These steps may vary for other communications programs.

14. At the top of the HyperTerminal window, shown below, click on Transfer, then on Send File.

Enter filename for example,

UMconfig.sav

Select Xmodem

Send button

15. In the Send File window, as shown above:

• In the Filename box, enter the full path of the file to be uploaded—for example, UMconfig.sav—or click on the Browse button to locate the file.

• In the Protocol box, select Xmodem from the drop-down list.

• Click on the Send button. (To close the window without sending the file, click on Close or Cancel.)

16. When the transfer is complete, a confirmation message—“Upload Successful”—appears in the Service Terminal Interface window and the Universal Monitor reboots with the new configuration.

9.9.6 Setup Serv Ph Num - Enter Phone Number

The Service Phone Number (Serv Ph Num) is used for remote monitoring by Liebert Global Services. The number is designed to allow remote monitoring services to connect to the Universal Monitor. All alarms will be sent to this number. When an alarm occurs, this number is dialed before any of the four pager numbers.

To use the service phone number features, be sure to connect the phone line connector to a telephone wall jack using an RJ11 cord, as described in 4.6.2 - Phone Line Connector.

Table 32 Service phone number dialing results

Result of Dialing Action Message Generated

Successful ——

Unsuccessful due to:

Busy signal / no answer / no dial tone

General modem communication problem

No communication with modem (internal hardware problem)

Universal Monitor generates message after all three redial attempts have failed, dials next configured pager.

Universal Monitor resets modem, generates message, redials up to three more times.

Universal Monitor generates messages, makes no further dialing attempts.

System and Control Options

Unsuccessful Page (Event Log)

Modem Reset (Event Log)

Modem Internal Fault

(Active Alarm Report, Alarm History Log)

To set up the service phone number:

• From the Setup System Info Menu, use the arrows

↑↓ to choose

Setup Serv Ph Num, then press Enter ↵ .

• See Table 33 for guidelines on entering the phone number, which may consist of up to 40 characters. To enter the phone number:

• Use the arrows

↑↓ to choose a character.

• Press Enter ↵ to advance to the next character position.

• When finished, press Enter ↵ again.

Table 33 Guidelines for dialing service phone number

Device type Required entries Example

Remote

modem

Device type Optional entries Example

All types

of devices

The first character must be “M”. M18005551212

Use “9” if needed to access an outside line—place after first character (M).

Use "W" to wait for a second dial tone before dialing if the phone system has two dial tones (initial tone and a second tone for outside line)—place after “9” (before the number to be dialed).

Use “,” (comma) to pause two seconds. M1,8005551212

M918005551212

M9W18005551212

Setup System Info Menu

SETUP SYSTEM INFO CHANGE PASSWORD CHANGE DATE & TIME ↑↓=NEXT ↵ =SELECT

SETUP SITE ID CONNECT BATTERY

> SETUP SERV PH NUM

FACTORY DEFAULTS

Setup Serv Ph Num

ENTER PHONE NUMBER

M18005551212

↑↓=SELECT ↵ =NEXT/END

System and Control Options

9.9.7 Setup Serv Ph Num - Communications Check (Service Terminal Interface only)

The Service Terminal Interface offers two additional options for setting up the Service Phone Number (Serv Ph Num) that are not available through the LCD interface:

• Enable communications check

• Enter time to perform communications check

To access these options:

• Connect to the Universal Monitor either from a remote computer or through the RS232 port (see A.2 - Connecting to the Service Terminal Interface).

• At the Main Menu, enter 0 (zero—Setup System-Login Required).

• At the Login Menu, enter your password.

• At the Setup Menu, enter 7 (Setup System Information).

• At the Setup System Information Menu, enter 6 (Setup Service Phone Number).

• At the Setup Service Phone Number menu, shown below, enter 1 to begin the setup.

Setup Service Phone Number (Service Terminal Interface only)

SETUP SERVICE PHONE NUMBER

This number receives all alarms in addition to the 4 pagers

1=SETUP SERVICE PHONE NUMBER ****************** 2=RETURN TO SETUP SYSTEM INFO MENU An “M” is required 3=RETURN TO SETUP MENU as 1st character. 4=RETURN TO MAIN MENU ******************

CURRENT NUMBER

SELECT A NUMBER:1

• At the Enter Service Phone Number prompt, you may press Enter to bypass this option (or see

9.9.6 - Setup Serv Ph Num - Enter Phone Number for instructions on entering the number).

>ENTER SERVICE PHONE NUMBER(40 CHARACTERS MAX). >[] >[ >COMMAND SUCCESSFUL

Enable Communications Check

Enabling this function permits a daily communications test between the Universal Monitor and the selected service phone number. Once each day the Universal Monitor dials the service phone number at a specified time and sends this message: “UNIVERSAL MONITOR COMM CHECK.” (The time of the test is specified at the next prompt, Enter Time To Perform Communications Check.)

• At the Enable Communications Check prompt, enter Y (Yes - enable) or N (No - disable). The current setting appears in brackets—[N] in the following example.

>ENABLE COMMUNICATIONS CHECK-YES(Y) OR NO(N)? >[N] > >COMMAND SUCCESSFUL

• Press Enter to proceed, or Escape to cancel the entry. If you make a change, a confirmation message appears: “Command Successful.”

Enter Time To Perform Communications Check

This function schedules the daily communications test between the Universal Monitor and the selected service phone number, as described in the previous section.

>ENTER TIME TO PERFORM COMMUNICATIONS CHECK(HH:MM). >[00:00] >[ >COMMAND SUCCESSFUL

• Press Enter to proceed, or Escape to cancel the entry. If you make a change, a confirmation message appears: “Command Successful.”

System and Control Options

9.9.8 Factory Defaults

At any time, you may restore all default values for settings in the Universal Monitor as it was shipped.

NOTE

This action will overwrite any configuration settings. You may want to back up your settings before restoring the factory defaults. See Backup and Upload Configuration File

(Service Terminal Interface only) in A.6.7 - Setup System Info for details on backing up settings using the Service

Terminal Interface.

The password is the sole exception when reverting to the factory default settings. The password can be reset to the factory default of AAAA only through the DIP switches. For details, see Change Password on page 69.

9.9.9 Perform Firmware Update (Service Terminal Interface only)

This function, which may be performed only through the Service Terminal Interface, upgrades the Universal Monitor’s firmware to the newest version.

NOTE

This action will overwrite any configuration settings. You may want to back up your settings before restoring the factory defaults. See Backup and Upload Configuration File

(Service Terminal Interface only) in A.6.7 - Setup System Info for details on backing up settings using the Service

Terminal Interface.

Setup System Info Menu

SETUP SYSTEM INFO CHANGE PASSWORD CHANGE DATE & TIME ↑↓=NEXT ↵ =SELECT

SETUP SITE ID CONNECT BATTERY SETUP SERV PH NUM

> FACTORY DEFAULTS

Factory Defaults

RESTORE ALL DEFAULTS ARE YOU SURE? N

↑↓=Y/N ↵ =END

• Connect to the Universal Monitor either from a remote computer or through the RS232 port (see A.2 - Connecting to the Service Terminal Interface).

• At the Main Menu, enter 0 (zero—Setup System-Login Required).

• At the Login Menu, enter your password.

• At the Setup Menu, enter 7 (Setup System Information).

• At the Setup System Info menu, enter 8 (Perform Firmware Update).

• At the Perform Firmware Update menu, shown below, enter 1 to proceed with an update.

Firmware Update (Service Terminal Interface only)

PERFORM FIRMWARE UPDATE

This command will update the existing firmware

1=PERFORM FIRMWARE UPDATE 2=RETURN TO SETUP SYSTEM INFO MENU 3=RETURN TO SETUP MENU 4=RETURN TO MAIN MENU

SELECT A NUMBER:1

To perform the update:

1. At the Perform Firmware Update prompt, enter Y (Yes - begin) or N (No - cancel). The current setting appears in brackets—[N] in the following example.

>PERFORM FIRMWARE UPDATE-YES(Y) OR NO(N)? >[N] >[

System and Control Options

NOTE

The following instructions refer to the Microsoft Windows HyperTerminal program. These steps may vary for other communications programs.

2. The firmware update is a two-step process—this step describes how to upload the file prog###.s19 (where ### is a number—for example, prog118.s19) to the Universal Monitor:

a. At the top of the HyperTerminal window, shown below, click on Transfer, then on Send File.

Enter filename -

prog###.s19 or flash###.s19

Select Xmodem

Send button

b. In the Send File window, as shown above:

• In the Filename box, enter the full path of the file to be uploaded—prog###.s19—or click on the Browse button to locate the file.

• In the Protocol box, select Xmodem from the drop-down list.

• Click on the Send button. (To close the window without sending the file, click on Close or Cancel.)

• When the transfer is complete, a confirmation message appears in the Service Terminal Interface window.

3. Next, follow these steps to upload the file flash###.s19 (where ### is a number—for example, flash607.s19) to the Universal Monitor:

a. At the top of the HyperTerminal window, shown above, click on Transfer, then on Send File. b. In the Send File window, shown above:

• In the Filename box, enter the full path of the file to be uploaded—flash###.s19—or click on the Browse button to locate the file.

• In the Protocol box, select Xmodem from the drop-down list.

• Click on the Send button. (To close the window without sending the file, click on Close or Cancel.)

• When the transfer is complete, a confirmation message—“Firmware Update Successful”— appears in the Service Terminal Interface window and the Universal Monitor reboots with the new firmware update.

9.9.10 Initiate Remote Alarm Test (Service Terminal Interface only)

The service phone number is used for remote monitoring by Liebert Global Services. The Service Terminal Interface may be used to test communications between the Universal Monitor and the service modem. This test will send a “DIAL OUT TEST PASSED” message to the service phone number.

The test is used to simulate an alarm to verify the proper configuration and functioning of the modem and other communications required for receiving alarms. This simulated alarm bypasses the normal alarm sequence—the LCD will not flash, the horn will not sound and there will be no record in the Alarm Log. A message is sent to the service phone number only if the alarm system is set up correctly.

To initiate the remote alarm test:

• Connect to the Universal Monitor either from a remote computer or through the RS232 port (see A.2 - Connecting to the Service Terminal Interface).

• At the Main Menu, enter 0 (zero—Setup System-Login Required).

• At the Login Menu, enter your password.

• At the Setup Menu, enter 7 (Setup System Information).

• At the Setup System Info menu, enter 9 (Initiate Remote Alarm Test).

• At the Initiate Remote Alarm Test menu, shown below, enter 1 to initiate the remote alarm.

Initiate Remote Alarm Test (Service Terminal Interface only)

INITIATE REMOTE ALARM TEST

This command simulates an alarm to test alarm notification setup for the service phone number

System and Control Options

1=INITIATE REMOTE ALARM TEST 2=RETURN TO SETUP SYSTEM INFO MENU 3=RETURN TO SETUP MENU 4=RETURN TO MAIN MENU

SELECT A NUMBER:1

• At the Simulate An Alarm Condition prompt, enter Y if you wish to proceed or N if you want to cancel the alarm simulation.

>SIMULATE AN ALARM CONDITION-YES(Y) OR NO(N)? >[N] >[ >COMMAND SUCCESSFUL

• After the “Command Successful” message appears, disconnect from the modem—at the top of the HyperTerminal window, click on Call, then on Disconnect, as shown below.

Disconnect

• Wait for the Universal Monitor to dial out to send a test message.

• To verify whether the test was successful, check the Event Log (see 7.3 - View Event Log) for one of these two messages: Dial out test passed or Dial out test failed.

NOTE

Also verify that a message was received at the Service Phone Number.

If the test is NOT successful, check the following:

• Modem configuration (see 9.8.1 - Modem Setup - Initialization String)

• Pager configuration (see 9.8.3 - Pager Setup - Pager Number and PIN)

9.10 Setup Exp Board - Optional Expansion Board

By default, the optional Expansion Board is configured as Not connected (N). After connecting power to the board and connecting it to the Universal Monitor, you must specify the Expansion Board as Connected (Y), as described in this section.

NOTE

Before specifying the Expansion Board as Connected, be sure to connect power to the board and connect it to the Universal Monitor. For more information, see:

• 3.4 - Input Power Connections - Optional Expansion Board

• 5.3.1 - Connect EIA485 Connectors to Main Board

System and Control Options

To change the Expansion Board connection setting:

• From the Main Menu, use the arrows

↑↓ to choose System and

Control, then press Enter ↵ (see 9.1 - Login for help).

• Enter your password at the Login screen.

• From the System and Control Menu, use the arrows

↑↓ to choose

Setup System, then press Enter ↵ .

Identify the Expansion Board as Connected (Y) or Not Connected (N)

• From the Setup System Menu, shown at right, use the arrows to

choose Setup Exp Board and press Enter ↵ .

• To change this setting, use the arrows

↑↓ to choose Y (Yes - Con-

↑↓

nected) or N (No - Not connected), then press Enter ↵ .

Setup System Menu

SETUP INPUT SETUP COMMON ALARM SETUP SENSOR SETUP I/O MATRIX ↑↓=NEXT ↵ =SELECT

SETUP OUTPUT SETUP MODEM&PAGERS SETUP SYSTEM INFO

> SETUP EXP BOARD

Expansion Board Connected

IS THE EXPANSION BOARD CONNECTED? N

↑↓=Y/N ↵ =END

9.11 Manual Output Ctrl

The Manual Output Ctrl feature allows you to manually change the state of any digital output to ON or OFF, overriding automatic control by the Universal Monitor (the default setting for all outputs). This menu also allows you to release the manual override, returning any output to automatic control.

There are two ways to override automatic control of outputs:

• Use the Manual Output Ctrl menu, as described in this section, to turn any output ON or OFF.

• Use the switch on the Universal Monitor board (see 1.7 - Controller Board Overview) to force all eight outputs ON at the same time. (Note: This has no effect on the optional Expansion Board outputs.)

After an output is forced manually ON or OFF through the Manual Output Ctrl menu, it remains in that state until returned to automatic control through this menu.

Table 34 summarizes the four types of control, including the abbreviated message that appears on the LCD and in log reports.

System and Control Options

Table 34 Automatic / manual control - output points

Message Description

AUTO Automatic Controlled by Universal Monitor

MAN ON Manually ON

MAN OFF Manually OFF

HW MAN ON

Manually ON (all outputs)

This output forced ON or OFF via Manual Output Ctrl menu

All outputs forced ON via hardware switch on circuit board

To force an output point ON or OFF or return it to automatic control:

• From the Main Menu, use the arrows

↑↓ to choose System and

Control, then press Enter ↵ (see 9.1 - Login for help).

• Enter your password at the Login screen.

• From the System and Control Menu, use the arrows

↑↓ to choose

Manual Output Ctrl, then press Enter ↵ .

Select an Output

The Select Output menu, shown at right, display the current status of all eight outputs.

• Use the arrows

↑↓ to choose the output you want—for example,

Output01—and press Enter ↵ .

Turn Output ON or OFF / Return to Automatic

• From the Override Output menu, use the arrows

↑↓ to choose

one of these options:

• Auto (return to automatic control)

• Man ON (manually turn this output ON)

• Man OFF (manually turn this output OFF)

• Press Enter ↵ .

Main Menu

VIEW STATUS

> SYSTEM AND CONTROL

↑↓=NEXT

↵ =SELECT

↑↓=SELECT ↵ =NEXT/END

AAAA

System & Control Menu

SETUP SYSTEM

> MANUAL OUTPUT CTRL

CLEAR ALARMS & LOGS

↑↓=NEXT

↵ =SELECT

Select Output

OVERRIDE OUTPUT

> OUTPUT01 AUTO

OUTPUT02 AUTO ↑↓=NEXT ↵ =SELECT

OUTPUT03 AUTO OUTPUT04 MAN ON OUTPUT05 AUTO OUTPUT06 AUTO OUTPUT07 MAN OFF OUTPUT08 AUTO OUTPUT09 AUTO OUTPUT10 MAN ON OUTPUT11 AUTO OUTPUT12 AUTO OUTPUT13 MAN OFF OUTPUT14 AUTO OUTPUT15 AUTO OUTPUT16 AUTO

Override Output

SELECT OUTPUT01

AUTO

↑↓=SELECT ↵ =END

NOTE: OUTPUT09-OUTPUT16 for optional Expansion Board

System and Control Options

9.12 Clear Alarms & Logs

The Clear Alarms & Logs menu allows you to clear active alarms or delete all records from any of the Universal Monitor’s three logs: alarm, event and trend logs.

To clear alarms or logs:

• From the Main Menu, use the arrows Control, then press Enter ↵ (see 9.1 - Login for help).

• Enter your password at the Login screen.

• From the System and Control Menu, use the arrows Clear Alarms & Logs, then press Enter ↵ .

• Use the following steps to clear alarms or delete log records.

9.12.1 Clear Active Alarms

To clear all active alarms:

• From the Clear Alarms/Logs Menu, use the arrows Clear Active Alarms, then press Enter ↵ .

• Use the arrows N (No - do not clear alarms), then press Enter ↵ .

Clearing active alarms is the only means to reset latched alarms. This step is required to return latched points to their normal state. To set up a digital input or an analog sensor input as latched, see:

↑↓ to choose Y (Yes - clear all active alarms) or

↑↓ to choose System and

↑↓ to choose

Main Menu

VIEW STATUS

> SYSTEM AND CONTROL

↑↓=NEXT

↵ =SELECT

↑↓=SELECT ↵ =NEXT/END

AAAA

System & Control Menu

SETUP SYSTEM MANUAL OUTPUT CTRL

> CLEAR ALARMS & LOGS

↑↓=NEXT

↵ =SELECT

Clear Alarms/Logs Menu

> CLEAR ACTIVE ALARMS

CLEAR ALARM LOG CLEAR EVENT LOG ↑↓=NEXT ↵ =SELECT

CLEAR TREND LOGS

Clear Active Alarms

CLEAR ACTIVE ALARMS ARE YOU SURE? N

• 9.3.4 - Set Up Alarmable Inputs in Latched or Unlatched Mode

• 9.5.8 - Set Up Alarmable Sensors in Latched or Unlatched Mode

9.12.2 Clear the Alarm Log

The alarm log contains up to 99 records of alarms that have occurred. You may want to clear the log after backing up the file or simply to free up space.

NOTE

Before deleting the records in the alarm log, you may want to back up the file to a remote computer using the Service Terminal Interface, as described in 8.2 - Back Up Log Files (Service Terminal Interface only).

To delete all records from the alarm log:

• From the Clear Alarms/Logs Menu, use the arrows Clear Alarm Log, then press Enter ↵ .

• Use the arrows

N (No - do not clear the alarm log), then press Enter ↵ .

NOTE

Clear active alarms is the only means to reset Latched alarms. This action must be taken to return Latched points to their normal state.

↑↓ to choose Y (Yes - clear the alarm log) or

↑↓=Y/N ↵ =END

Clear Alarms/Logs Menu

CLEAR ACTIVE ALARMS

> CLEAR ALARM LOG

CLEAR EVENT LOG ↑↓=NEXT ↵ =SELECT

CLEAR TREND LOG

Clear Alarm Log

CLEAR ALARM LOG ARE YOU SURE? N

↑↓=Y/N ↵ =END

↑↓ to choose

System and Control Options

9.12.3 Clear the Event Log

The event log contains up to 99 records of events detected by the Universal Monitor. You may want to clear the log after backing up the file or simply to free up space.

NOTE

Before deleting the records in the event log, you may want to back up the file to a remote computer using the Service Terminal Interface, as described in 8.2 - Back Up Log Files (Service Terminal Interface only).

To delete all records from the event log:

• From the Clear Alarms/Logs Menu, use the arrows Clear Event Log, then press Enter ↵ .

• Use the arrows

↑↓ to choose Y (Yes - clear the event log) or N (No -

do not clear the event log), then press Enter ↵ .

9.12.4 Clear the Trend Logs

The Universal Monitor maintains a separate trend log for each configured analog input sensor. Each log contains up to 100 records of data collected at regular intervals. You may want to clear the logs after backing up the files or simply to free up space.

Using the Clear Trend Logs command will clear all four trend logs maintained by the Universal Monitor. There is no method of clearing records from individual logs.

NOTE

Before deleting the records in the trend logs, you may want to back up the files to a remote computer using the Service Terminal Interface, as described in 8.2 - Back Up Log Files (Service Terminal Interface only).

Clear Alarms/Logs Menu

CLEAR ACTIVE ALARMS CLEAR ALARM LOG

> CLEAR EVENT LOG

↑↓=NEXT ↵ =SELECT CLEAR TREND LOGS

Clear Event Log

CLEAR EVENT LOG ARE YOU SURE? N

↑↓=Y/N ↵ =END

↑↓ to choose

Clear Alarms/Logs Menu

CLEAR ACTIVE ALARMS CLEAR ALARM LOG CLEAR EVENT LOG ↑↓=NEXT ↵ =SELECT

> CLEAR TREND LOGS

Clear Trend Log

CLEAR TREND LOGS ARE YOU SURE? N

↑↓=Y/N ↵ =END

To delete the records from ALL four trend logs:

• From the Clear Alarms/Logs Menu, use the arrows Enter ↵ .

• Use the arrows

↑↓ to choose Y (Yes - clear all trend logs) or N (No - do not clear the trend logs),

then press Enter ↵ .

↑↓ to choose Clear Trend Logs, then press

10.0 SPECIFICATIONS

10.1 Universal Monitor Specifications

Specifications

Small Enclosure Large Enclosure

Power Requirements

Dimensions W x D x H, in. (mm)

Weight (Assembled) 7.68 lb. (3.48 kg) 20.56 lb. (9.33 kg)

Enclosure Type NEMA 1

Liquid Crystal Display (LCD) Four line, 20 character, backlit

Mounting Surface Building Wall or Structural Member

Ambient Operating Environment

Processor Specifics

Model Motorola XC68HC812A4

Clock speed 16MHz

Total RAM 256Kb

Total FLASH 4M

Total EEPROM 4K

A/D Resolution (Analog IN) 12 Bit

Modem Type Embedded 14.4K bps

Clock Type Real-Time Clock

Clock battery backup type Lithium Cell (non-replaceable)

Clock battery life 7 years, constant, no power

Modem battery backup type Nickel Cadmium (replaceable)

Modem battery life 10 minutes at full load

Communications

Local Communications RS232

Remote Communications

Modem (9600-N-8-1) Supported pagers

SiteScan Web IGM Protocol, EIA422

Expansion Board (optional) EIA485

Agency Listings

UL UL3121 UL1012 UL1585

CSA C22.2 No. 1010

CE Yes Yes

FCC Compliance CFR 47 Part 15 N/A

Inputs & Outputs (Quantity)

Digital Inputs (8) Dry Contact Closure 24VDC, 10 mA

Analog Inputs (4)

Digital Outputs (8) 24VAC, 3A

Common Alarm Outputs (2) 24VAC, 3A

UMS02400

24VAC ±10%

of nominal;

50/60 Hz, 1.3A,

30VA

14-1/4 x 2-3/4 x 12

(361.95 x 69.85 x 304.8)

32ºF to 104ºF (0ºC to 40ºC)

0% RH to 95% RH (non-condensing)

Baud rate 9600 bps, Parity=None, Data bits=8, Stop bits=1

9600 E-7-1 supports TAPI protocol version 1.8

No Transformer Module With Transformer Module

(UMS02400)

4-20 mA signal input with selectable

power source of 12VDC or 24VDC

115VAC

UML11500

115VAC ±10%

of nominal;

60Hz, 4A,

460VA

18 x 2-3/4 x 18

(457.2 x 69.85 x 457.2)

115VAC (TM115)

C22.2 No. 66 and

C22.2 No. 107.1

230VAC

UML23000

230VAC ±10%

of nominal;

50Hz, 0.5A,

115VA

230VAC (TM230)

NOTE

If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

10.2 Optional Expansion Board Specifications

Specifications

Power Requirements

Dimensions W x D x H, in. (mm)

Weight (Assembled) 7.68 lb. (3.48 kg)

Enclosure Type NEMA 1

Mounting Surface Building Wall or Structural Member

Ambient Operating Environment

Inputs & Outputs (Quantity)

Digital Inputs (16)

Digital Outputs (8) 240VAC, 2A

24VAC ±10% of nominal;

50/60 Hz, 0.6A, 15VA Class 2

(361.95 x 69.85 x 304.8)

32ºF to 104ºF (0ºC to 40ºC)

0% RH to 95% RH (non-condensing)

UMEXP

14-1/4 x 2-3/4 x 12

Dry Contact Closure

24VDC, 10 mA

NOTE

If the equipment is used in a manner not specified by the manufacturer, the protection provided by the equipment may be impaired.

Service Terminal Interface

APPENDIX A- SERVICE TERMINAL INTERFACE

The Service Terminal Interface allows access to all functions of the Universal Monitor, including some that are not possible through the LCD interface. This interface is accessible through any computer using a communications program such as Microsoft

Windows® HyperTerminal.

This appendix provides directions for connecting to the Service Terminal Interface, an overview of each type of function and sample screens for each menu available through the Service Terminal Interface. References to more detailed instructions about each function are provided.

A.1 COMPARISON OF FUNCTIONS: LCD AND SERVICE TERMINAL INTERFACE

Table 35 lists all functions for viewing and configuring the Universal Monitor and shows whether they can be performed through the LCD interface and where to find information.

Table 35 Guide to Universal Monitor functions

Can be performed via: Where to find:

Function

VIEW STATUS FUNCTIONS

SILENCE ALARM & BACK UP LOGS FUNCTIONS

Silence Alarm (On the LCD, press any key to silence an alarm) ✔✔ page 40 page 100 Back Up Log Files — ✔ page 41 page 101

SYSTEM & CONTROL FUNCTIONS

Setup System ✔✔ page 45 page 105

Setup System Info ✔✔ page 68 page 121

Setup Exp Board - Optional Expansion Board ✔✔ page 79 page 127 Manual Output Ctrl ✔✔ page 80 page 128 Clear Alarms & Logs ✔✔ page 81 page 130

Clear Active Alarms ✔✔ page 81 page 130 Clear the Alarm Log ✔✔ page 81 page 130 Clear the Event Log ✔✔ page 82 page 131 Clear the Trend Logs ✔✔ page 82 page 131

LCD

Service

Terminal

Instructions on

using function

Service Terminal screen examples

Connecting to the Service Terminal Interface

A.2 CONNECTING TO THE SERVICE TERMINAL INTERFACE

This section describes how to set up and connect to the Service Terminal Interface.

A.2.1 Connection Methods

There are two ways to access the Service Terminal Interface:

• Direct—Use a null modem cable to connect a computer’s COM1 port to the Universal Monitor’s RS232 port,

• Remote—Use a remote computer’s modem to dial the telephone number of the phone line connected to the Universal Monitor.

Both methods require a communications program, such as HyperTerminal, to connect to the Service Terminal Interface.

Refer to Table 36 for step-by-step instructions to set up each type of connection. Note that the remote connection does not require setting up the COM1 port.

Table 36 Steps to set up a direct or remote connection

Direct Remote

A.2.2 - Create a Connection ✔✔

A.2.3 - Set Up the COM1 Port - Direct Connection Only ✔ N/A

A.2.4 - Set Up the Connection’s Properties ✔✔

A.2.5 - Connect to the Service Terminal Interface ✔✔

The instructions in this section refer to the HyperTerminal program—they may vary for other communications programs.

A.2.2 Create a Connection

Before connecting to the Service Terminal Interface, you must create a connection and specify the method to be used for connection, as described in the following steps.

1. Start the HyperTerminal program—to do this, click on the Start button, then on Programs, then Accessories, then Communications, and finally HyperTerminal.

2. At the top of the HyperTerminal window, click on File, then on New Connection, as shown below left.

3. In the Connection Description window, shown above right, enter a name for the connection—for example, Universal Monitor. This becomes the file name (with the extension “.ht”).

4. Click OK to close the window. The Connect To window opens, as shown below.

Connecting to the Service Terminal Interface

Enter a name for the connection for example,

Universal Monitor

(DIRECT CONNECTION) Choose COM1

(REMOTE CONNECTION) Choose the computer’s modem

5. In the Connect To window, select the appropriate connection method from the Connect Using drop-down list:

Direct Connection via RS232

• To set up a direct connection via the Universal Monitor’s RS232 port, select COM1 as shown above left.

• This opens the COM1 Properties window. Proceed to Step 6 (next section).

Remote Connection via Modem

• To make a remote connection through the Universal Monitor’s modem, select your computer’s modem—HSP56 MicroModem in the example shown above right.

• Enter the area code and phone number of the Universal Monitor’s modem.

• Proceed to Step 8 in A.2.4 - Set Up the Connection’s Properties (skip Steps 6 and 7).

A.2.3 Set Up the COM1 Port - Direct Connection Only

The following steps apply only to setting up a direct connection to the Service Terminal Interface via the Universal Monitor’s RS232 port. If you are setting up a remote connection via modem, skip to Step 8 (next section).

COM1 Port Setup

6. In the COM1 Properties window, shown below, make the following selections:

• Bits per second: 9600

• Data bits: 8

•Parity: None

• Stop bits: 1

• Flow control: None

Connecting to the Service Terminal Interface

7. Click OK. When the connection is open, the connection name appears in the title bar of the HyperTerminal window. To complete the setup, continue with Step 8 (next section).

A.2.4 Set Up the Connection’s Properties

The following steps are needed for both direct and remote connection to the Universal Monitor.

Properties Setup

8. Open the Properties window by clicking on File, then on Properties, as shown below left.

9. In the Properties window, above right, click on the Settings tab and choose the following settings:

• Function, arrow, and ctrl keys act as: Terminal keys

• Backspace key sends: Ctrl+H

• Emulation: ANSIW

• Telnet terminal ID: VT100

• Backscroll buffer lines: 500

• Play sound when connecting or disconnecting: Unchecked

Connecting to the Service Terminal Interface

Settings tab

ASCII Setup

10. In the Properties window, click on the ASCII Setup button, shown below left.

ASCII Setup button

11. In the ASCII Setup window, shown above right, choose the following settings:

• ASCII Sending: place a check mark (

• ASCII Receiving: place a check mark (

•Click OK.

The setup is now complete. To use the new connection, proceed to the next section, A.2.5 - Connect to the Service Terminal Interface.

✔) in the Send Line Ends With Line Feeds box.

✔) in the Wrap Lines That Exceed Terminal Width box.

A.2.5 Connect to the Service Terminal Interface

After creating and setting up a connection, use a communications program such as HyperTerminal to access the Universal Monitor’s Service Terminal Interface.

1. Verify communications connections between the remote computer and the Universal Monitor: a. For direct connection (via RS232 port):

• Connect a null modem cable from the computer’s COM1 port to the Universal Monitor’s RS232 port (for location, see 4.6.1 - RS232 Connector).

b. For remote connection (via modem):

• Verify modem connections between the remote computer and the Universal Monitor. The remote computer should have connectivity through a telephone line, high-speed cable or an Ethernet. The Universal Monitor must have a telephone line connected to its RJ11 port (for location, see 4.6.2 - Phone Line Connector).

2. Start the HyperTerminal program—click on the Start button, then on Programs, then Accessories, then Communications, and finally HyperTerminal.

3. Open the Universal Monitor connection created in A.2.2 - Create a Connection. To do this, click on File, then on Open, as shown below.

Connecting to the Service Terminal Interface

Click on the file name for example,

Universal Monitor.ht

4. In the Open window, shown above right, select the file name—Universal Monitor.ht in this example—and then click on the Open button.

5. Follow the steps below to display the Main Menu of the Service Terminal Interface: a. For direct connection (via RS232 port):

• Press Enter (or Escape) to initiate communication and bring up the Main Menu.

b. For remote connection (via modem):

• The Connect window opens, as shown below left. Click the OK button.

• In the Connect window, below right, click Dial.

• If the dialing attempt is successful, the Main Menu appears.

Dial button

OK button

For more information on the Universal Monitor’s options:

• See A.3 - Overview of Menus for examples of the Service Terminal Interface screens.

• See Table 35 to locate step-by-step instructions for each Universal Monitor function.

A.3 OVERVIEW OF MENUS

The Main Menu offers choices for viewing the status of the Universal Monitor, silencing the audible alarm and backing up the unit’s log files. It also allows access to the System and Control features, which require a password.

The following shows where to find examples of the Main Menu screens:

Main Menu For sample screens, see:

1=VIEW ACTIVE ALARMS A.4 - View Status Menus

2=VIEW ALARM LOG

3=VIEW EVENT LOG

4=VIEW TREND LOG

5=VIEW INPUT & SENSOR STATUS

6=VIEW OUTPUT STATUS

7=VIEW PAGER NUMBERS

8=SILENCE ALARM A.5 - Silence Alarm & Back Up

Overview of Menus

Log Files (Service Terminal Interface only)9=BACKUP LOG FILES

0=SETUP SYSTEM-LOGIN REQUIRED A.6 - Setup Menu

A.3.1 View Status Overview

The View Status features are available to all users. This permits all personnel to check on the status of any equipment or location being monitored. These options allow any user to:

• View current monitoring data—active alarms and the status of all inputs and outputs

• View data stored in alarm, event and trend logs

• View pager numbers

A.3.2 Silence Alarm and Backup Log Files

Two Main Menu options—Silence Alarm and Backup Log Files—are unique to the Service Terminal Interface. As with the View Status options, these features do not require a password:

• Silence Alarm—silence the Universal Monitor’s audible alarm and reset the Common Alarm Relay output.

• Backup Log Files—make backup copies of the Universal Monitor’s Alarm Log, Event Log and Trend Logs and save the copies to a computer.

A.3.3 Setup Menu Overview

The Setup Menu options require a password. Authorized users may:

• Configure the Universal Monitor—this includes setting up digital and analog inputs, digital outputs, the modem, up to four pagers, and system features such as setting the date and time

Three system features—Backup and Upload Configuration File, Firmware Update and Initiate Remote Alarm Test—are unique to the Service Terminal Interface.

• Override automatic control of outputs to force an output ON or OFF

• Clear active alarms and delete all records in the alarm, event and trend logs

A.4 VIEW STATUS MENUS

The View Status menu allows any user to view currently active alarms, monitoring data stored in the alarm, event and trend logs, the status of all inputs and outputs, and the four pager numbers.

Main Menu

After connecting to the Service Terminal Interface, the Main Menu appears, as shown below. This section presents Service Terminal Interface screens for options 1 through 7:

Main Menu

LIEBERT UNIVERSAL MONITOR

VX.XXX.X

View Status Menus

MAIN MENU

For sample screens, see:

1=VIEW ACTIVE ALARMS Section A.4.1

2=VIEW ALARM LOG Section A.4.2

3=VIEW EVENT LOG Section A.4.3

4=VIEW TREND LOG Section A.4.4

5=VIEW INPUT & SENSOR STATUS Section A.4.5

6=VIEW OUTPUT STATUS Section A.4.6

7=VIEW PAGER NUMBERS Section A.4.7

8=SILENCE ALARM

9=BACKUP LOG FILES

0=SETUP SYSTEM-LOGIN REQUIRED

SELECT A NUMBER:1

Liebert Universal Monitor User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

1.0 INTRODUCTION

1.1 Methods of Viewing and Configuring the Universal Monitor

1.2 Data Logs

1.3 Optional Features

1.4 Available Alarms

1.5 Outside Enclosure Overview

Figure 1 Small enclosure—external features

Figure 2 Large enclosure—internal features

1.6 Typical Configuration

Figure 3 Typical Configuration

1.7 Controller Board Overview

1.8 Optional Expansion Board Overview

Table 2 Expansion board components

1.9 LED Indicators

Table 3 LED indicators summary

1.10 LED Indicators - Optional Expansion Board

Table 4 LED indicators summary

1.11 Typical Sequence

Figure 4 Example of typical sequence: Analog input reaches high setpoint

2.0 INSTALLATION - MAIN BOARD

2.1 Installation Considerations

2.1.1 Unpacking and Preliminary Inspection

Packing Contents

Table 5 Packing manifest - Universal Monitor main board

2.2 Surface-Mounting the Universal Monitor

Required tools

2.2.1 Mounting the Panel

Figure 5 Mounting Dimensions

2.3 Flush-Mounting the Universal Monitor

Required tools

2.3.1 Mounting the Panel

2.4 Connect Power to the Universal Monitor

2.4.1 Input Power Connections - Small Enclosure

Figure 6 Electrical connections to panel

2.4.2 Termination and Mounting - Large Enclosure

Input Power Connections

24 VAC Output Power Connections

Troubleshooting - Transformer Module

2.4.3 Connecting the Battery Pack

Obtaining a Replacement Battery Pack

3.0 INSTALLATION - OPTIONAL EXPANSION BOARD

3.1 Installation Considerations

3.1.1 Unpacking and Preliminary Inspection

Packing Contents

Table 6 Packing manifest - optional Expansion Board

3.2 Surface-Mounting the Optional Expansion Board

Required tools

3.2.1 Mounting the Panel

Figure 9 Mounting Dimensions - optional Expansion Board

3.3 Flush-Mounting the Optional Expansion Board

Required tools

3.3.1 Mounting the Panel

3.4 Input Power Connections - Optional Expansion Board

Figure 10 Electrical connections to panel

4.0 WIRING AND CONNECTIONS - MAIN BOARD

4.1 Wiring Specifications

Table 7 Wiring specifications - main board

4.2 Connecting Digital Inputs and Digital Outputs

4.2.1 Connecting Digital Inputs

4.2.2 Connecting Digital Outputs

4.2.3 Setting the Digital Output Jumpers

Table 8 Digital output jumper settings

4.3 Connecting Analog Inputs

4.3.1 Setting the 12VDC/24VDC Analog Power Jumper

4.3.2 Connecting the Analog Ground

4.4 Connecting Common Alarm Outputs

4.5 EIA422 SiteScan Web Connector

4.6 Communications Connections

4.6.1 RS232 Connector

4.6.2 Phone Line Connector

5.0 WIRING AND CONNECTIONS - OPTIONAL EXPANSION BOARD

5.1 Wiring Specifications

Table 9 Wiring specifications - optional Expansion Board

5.2 Connecting Inputs and Outputs

5.2.1 Connecting Digital Inputs

5.2.2 Connecting Digital Outputs