Liebert ICOM User Manual

Precision Cooling
For Business-Critical Continuity™

Liebert iCOM

™

User Manual - Intelligent Communications & Monitoring

TABLE OF CONTENTS

1.0 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

1.1 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

2.0 LIEBERT ICOM DISPLAY COMPONENTS AND FUNCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2.1 Navigating Through the Liebert iCOM Menus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.1.1 Control Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.1.2 Accessing Submenus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

2.1.3 Entering a Password . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

2.1.4 Viewing Multiple Units with a Networked Large Display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

3.0 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

3.1 Single Unit Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.1.1 Unit/Fan Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3.1.2 Chilled Water Units with Variable Speed Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

3.1.3 General Compressor Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

3.1.4 Compressor Timing—Units With Two Compressors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.1.5 Compressor Sequencing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

3.2 Temperature Control—Single Source Cooling (No Extra Cooling Coil) . . . . . . . . . . . . . . . . 16

3.2.1 Temperature Proportional Band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

3.2.2 Compressor Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

3.2.3 Chilled Water Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.3 Temperature Control—Second Cooling Source . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.3.1 Differential Temperatures / Controls (Comparator Circuit) . . . . . . . . . . . . . . . . . . . . . . . . . . 20

3.4 Temperature Control—Reheat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

3.4.1 Three-Stage Electric, Hot Gas and Hot Water Reheat. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

3.4.2 SCR Reheat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

3.5 Humidity Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

3.5.1 Humidification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

3.5.2 Dehumidification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

3.6 Control Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

3.6.1 Temperature and Humidity Control Types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

3.6.2 Humidity Sensor Reading Control Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

3.6.3 Supply Limit—Optional . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

3.6.4 High and Low, Temperature and Humidity Events . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

3.6.5 User Inputs / Customer Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

3.6.6 Event Types and Properties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

3.7 Possible Event Notifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

3.8 Next Maintenance Calculation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

3.8.1 Calculation of Next Maintenance and Diagnostics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

i

4.0 TEAMWORK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

4.1 Teamwork Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

4.1.1 Application of Teamwork Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

4.1.2 No Teamwork . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

4.1.3 Teamwork Mode 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

4.1.4 Teamwork Mode 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

4.1.5 Standby – Rotation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

5.0 INSTALLING A LIEBERT ICOM UNIT-TO-UNIT NETWORK. . . . . . . . . . . . . . . . . . . . . . . . . . .41

5.1 Placement of Cooling Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

5.2 U2U Hardware: Cables and Network Switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

5.3 Wiring for Unit-to-Unit Communications—U2U . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

5.3.1 Wiring a Liebert iCOM U2U Network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

5.4 External Communications—Building Management Systems, Liebert SiteScan® . . . . . . . . 47

6.0 MOUNTING A LARGE DISPLAY ON A WALL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

6.0.1 Location Considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

7.0 USER MENU PARAMETERS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50

8.0 SERVICE MENU PARAMETERS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

ii

FIGURES

Figure 1 Liebert iCOM components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Figure 2 Liebert iCOM display components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Figure 3 Status menu, large display, graphical view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Figure 4 Liebert iCOM default screen symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Figure 5 Menu tree—Small display, stand-alone or networked . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Figure 6 Menu tree—Large display, stand-alone. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Figure 7 Menu tree—Large display, networked. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Figure 8 User menu icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Figure 9 Service menu icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Figure 10 Start-stop priority switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Figure 11 Temperature proportional band . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16

Figure 12 One single-step compressor without unloaders. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17

Figure 13 Two single-step compressors without unloaders or one compressor with an unloader (two-step) 17

Figure 14 Two compressors with unloaders (four-step) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Figure 15 Digital scroll capacity modulation, 10-100% variable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Figure 16 Single and dual digital scroll compressor activation points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Figure 17 Three-point actuator control (example: cooling) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Figure 18 Second cooling source and compressorized cooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Figure 19 Three-stage heating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Figure 20 Two single-step compressors with SCR reheat set to Tight mode . . . . . . . . . . . . . . . . . . . . . . . . . 24

Figure 21 Two single-step compressors with SCR reheat set to Standard mode . . . . . . . . . . . . . . . . . . . . . . 25

Figure 22 Humidity proportional band. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Figure 23 Teamwork Mode 1 with two cooling units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Figure 24 Connecting two cooling units, each with a small display using a crossover Ethernet cable . . . . 43

Figure 25 Wiring a small display for stand-alone operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Figure 26 Wiring a small display for U2U network operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Figure 27 Wiring a large display for stand-alone operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Figure 28 Wiring a large display for U2U network operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Figure 29 Liebert iCOM input-output control board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Figure 30 Liebert vNSA with optional remote large display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Figure 31 Liebert iCOM display dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

iii

TABL ES

Table 1 Keyboard icons and functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

Table 2 User menu icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Table 3 Service menu icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Table 4 Reheat configuration types. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Table 5 Parameters for infrared humidifier control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

Table 6 Dehumidification With Comp settings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Table 7 Customer inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Table 8 Possible event settings—some events not available in all units . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Table 9 Event notifications—large or small display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Table 10 Sample Liebert iCOM network configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Table 11 Ports available for connecting Liebert iCOM control devices. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Table 12 Setpoints parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Table 13 Spare part list parameters—large display only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Table 14 Event log parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Table 15 Graphics parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Table 16 View network parameters—large display only* . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Table 17 Set alarms parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Table 18 Sensor data parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Table 19 Active alarms parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Table 20 Display setup parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Table 21 Total run hours parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Table 22 Timer parameters—Sleep Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Table 23 Service contacts parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Table 24 Setpoints parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Table 25 Unit diary parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Table 26 Maintenance / wellness settings parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Table 27 Standby settings / lead-lag parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Table 28 Diagnostics / service mode parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Table 29 Set alarms parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Table 30 Set alarms parameters (continued) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Table 31 Sensor calibration / setup parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Table 32 System / network setup parameters—large display only . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Table 33 Network setup parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Table 34 Options setup parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Table 35 Service contacts parameters. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

iv

1.0 INTRODUCTION

The Liebert iCOM™ control offers the highest capabilities in unit control, communication and moni­toring of Liebert mission-critical cooling units.

Liebert iCOM may be used to combine multiple cooling units into a team that operates as a single
entity, enhancing the already-high performance and efficiency of Liebert’s units.

Liebert iCOM is available as a factory-installed assembly or may be retrofitted on existing products
with SM, AM or AG controls. Large graphic display wall-mount versions of the control are available
for remote operation and monitoring of cooling units.

1.1 Features

Large and Small Displays

The Liebert iCOM control is available with either a large or small liquid crystal display.

•The Liebert iCOM with small display has a 128 x 64 dot matrix screen that simultaneously
shows two menu icons, along with descriptive text. This display is capable of controlling only the
unit it is directly connected to.

•The Liebert iCOM with large display has a 320 x 240 dot matrix screen that shows up to 16
menu icons at a time, as well as descriptive text. This display can be used to control a single cool­ing unit or any cooling unit on a network, regardless of how it is connected—either integrated into
a cooling unit or simply connected to the network and mounted remotely.

Introduction

Liebert iCOM’s menu-driven display is used for all programming functions on each connected cooling
unit. The Status menu shows the status of the conditioned space, such as room temperature and
humidity, temperature and humidity setpoints, alarm status and settings, event histories and the
current time.

Figure 1 Liebert iCOM components

Wall Mount Large Display

Direct Panel Mount Large Display and Bezel

Direct Panel Mount

Small Display and Bezel

Liebert iCOM Input/Output Board

1

Liebert iCOM Display Components and Functions

2.0 LIEBERT ICOM DISPLAY COMPONENTS AND FUNCTIONS

The small and the large display have a common key layout, as shown in Figure 2.

Figure 2 Liebert iCOM display components

Liquid Crystal Display

LED Status Indicators
(top LED is red or
flashing red; bottom
LED is green or amber)

?

ESC

Large Liebert iCOM Display
shown - Keypad and LEDs are
identical on all displays.

Keypad

On/Off Key

Alarm Key

Up Arrow Key

?

Help Key

ESC

Escape Key Down Arrow Key

NOTE

The Help key may be pressed at any time for a brief explanation of what is being viewed.

Left Arrow Key Right Arrow KeyEnter Key

2

Table 1 Keyboard icons and functions

Icon Key Name Function

On/Off Key Controls the operational state of the cooling unit.

Alarm Key Silences an alarm.

Liebert iCOM Display Components and Functions

?

ESC

Help Key Accesses integrated help menus.

ESCape Key Returns to the previous display view.

Enter Key Confirms all selections and selects icons or text.

Increase Key
(Up Arrow)

Decrease Key
(Down Arrow)

Left and Right
Arrow Keys

Upper LED

Moves upward in a menu or increases the value of a selected parameter.

Moves downward in a menu or reduces the value of a selected parameter.

Navigates through text and sections of the display.

Blinking Red—Active, unacknowledged alarm exists

Solid Red—Active, acknowledged alarm exists

Lower LED

Amber—Power is available to the unit, unit is NOT operating

Green—Power is available to the unit, unit is operating

3

Figure 3 Status menu, large display, graphical view

Temperature

System or
Unit # view

Temperature Sensor
Reading

Evaporator
Fan Speed

Percent Cooling

Free-Cooling
Percentage

Next Maintenance

Date and Time

Setpoint

Figure 4 Liebert iCOM default screen symbols

Liebert iCOM Display Components and Functions

Humidity
Setpoint

Humidity
Sensor
Reading

Supply
Air Temperature

Percent Hot Water
Heating

Percent Electric
Heating

Percent Dehumidifying

Percent Humidifying

System (or Unit) On/Off

Most Recent Alarms
(Date, Time, Unit,
Description)

fan

hot water

cooling

electric heat

freecooling

maintenance

dehumidification humidification

4

2.1 Navigating Through the Liebert iCOM Menus

Liebert iCOM shows icons and text for monitoring and controlling your Liebert cooling units or net­work of cooling units. The number of icons and amount of text shown depends on the display size.

2.1.1 Control Interface

When the buttons on the Liebert iCOM control have not been pressed for a short period, the display
backlight turns off. Pressing any key will turn the backlight on (wake up the screen) and display the
Status menu of the last cooling unit viewed. The Status menu will show the cooling unit’s operational
mode(s), return air temperature and humidity readings, temperature and humidity setpoints and any
active alarm conditions.

If the cooling unit has a large display and is not on a network, or if the unit has a small display,
whether it is networked or stand-alone, the Status menu will display only that cooling unit’s informa­tion. Any large display that is connected to a network can be used to view any cooling unit on the net­work or show an average view of the entire system of cooling units.

The Liebert iCOM control has three main menus; User, Service and Advanced.

The User menu contains the most frequently used features, settings and status information. The Ser­vice menu contains settings and features used to set up unit communications and for unit mainte­nance. The Advanced menu contains settings used to set up the unit at the factory.

NOTE

Menu settings may be viewed without a password, but changing settings requires a password.
If a password is required, Liebert iCOM shows a prompt to enter the password. The password
for the User menu is 1490. The password for Service menu is 5010. For details on entering a
password, see Entering a Password on page 6

Liebert iCOM Display Components and Functions

2.1.2 Accessing Submenus

To access the User, Service or Advanced menu, press the Enter or down arrow key while viewing the
Status menu of the unit you wish to access. The User menu will be displayed first. To view the Service
or Advanced menus, press the right arrow key.

Accessing Submenus on Small Displays

While viewing the menu you wish to access (User, Service or Advanced), use the up and down arrow
keys to scroll through the icons page-by-page. To scroll through the icons one-by-one, press the enter
key and then use the up and down arrow keys. With the desired icon highlighted, press the enter key
to enter that submenu. Once in a Submenu, a list of parameters is displayed.

Press the enter key and use the up and down arrow keys to scroll through the parameters one-by-one.
Pressing the Esc key will go back a level. Figure 5 shows the Liebert iCOM control menus for a small
display.

Accessing Submenus on Large Displays

While viewing the menu you wish to access (User, Service or Advanced), press the enter key to high­light the first icon. Use the arrow keys to navigate through the icons. With the desired icon high­lighted, press the enter key to enter that submenu. Once in a Submenu, a list of parameters will be
displayed.

The up and down arrow keys may be used to scroll through the parameters page-by-page if the sub­menu has multiple pages. To scroll item-by-item, press the Enter key and then use the up and down
arrow keys. Using the right or left arrow keys on large displays attached to a network will change the
unit being viewed. Pressing the Esc key will go back a level. Figures 6 and 7 show the Liebert iCOM
control menus for a stand-alone large display and for a networked large display, respectively.

NOTE

Settings are readable without a password, but changing settings requires a password.

5

2.1.3 Entering a Password

To change the value of a parameter in a menu, you must first enter the password for that menu. The
User, Service and Advanced menus each has a unique password to prevent unauthorized changes.

The User menu password is 1490; the Service menu password is 5010.

NOTE

Entering the Service menu password permits access to both the User and Service menus.

To enter a password:

1. Navigate to the menu that contains the parameter to be changed.

2. Select Password in the submenu by pressing the Enter key

3. Press the Enter key to move your cursor to the right side of the screen to select the question
marks.

4. Use the arrow keys to enter the numeral for the password’s first digit (the up arrow key moves
from 1 to the next digit).

5. Use the right arrow key to move to the next question mark and repeat Step 4 to enter all digits in
the password.

6. After entering the password, press enter.

If the password is correct, the Actual Level shown to the right of Password will change
from 0 to 1 or 2. The menu will remain locked if the password was incorrect.

Liebert iCOM Display Components and Functions

NOTE

Returning to the Status menu will require re-entering a password to make changes.

Figure 5 Menu tree—Small display, stand-alone or networked

Status Menu

Unit 1 View

User Menu

Password

Setpoints

Event Log

Graphics

Set Alarms

Sensor Data

Display Setup

Total Run Hours

Sleep Mode

Service Info

Service Menu

Password

Setpoints

Standby

Wellness

Diagnostics

Set Alarms

Calibration

Network Setup

Options Setup

Service Info

Active Alarms

Advanced Menu

Password

Factory Settings

Access Passwords

6

Figure 6 Menu tree—Large display, stand-alone

Liebert iCOM Display Components and Functions

Unit 1 will be displayed
in the top left corner of
the screen.

User Menu

Unit 1

Password

Setpoints

Spare Part List

Event Log

Graphics

View Network

Set Alarms

Sensor Data
Active Alarms
Display Setup

Total Run Hours

Sleep Mode

Service Contact Info

Status Menu – System View

Status Menu

Unit 1 View

Service Menu

Unit 1

Password

Setpoints

Unit Diary

Standby Settings/Lead-Lag

Maintenance/Wellness Settings

Diagnostics / Service Mode

Set Alarms

Sensor Calibration/Setup

System/Network Setup

Options Setup

Service Contact Info

Advanced Menu

Unit 1

Password

Factory Settings

Compressor Info

Access Passwords

7

Liebert iCOM Display Components and Functions

2.1.4 Viewing Multiple Units with a Networked Large Display

When you first wake up the control, press the Esc key to return to the System view Status menu. This
view shows an average of all the units on the network and any alarms present. To view a specific unit
on the network, press either the enter key or down arrow key. When you do this, you will see the word
System in the top left of the screen change to a unit number. Using the left and right arrow keys you
can toggle through the various units on the network. To go back to the System view, or back one level
from any menu in the control, press the Esc key.

Figure 7 Menu tree—Large display, networked

Unit # or System will be
displayed in the top left
corner of the screen.

User Menu

Unit #

Password

Setpoints

Spare Part List

Event Log

Graphics

View Network

Set Alarms

Sensor Data
Active Alarms
Display Setup

Total Run Hours

Sleep Mode

Service Contact Info

(Networked Large Display Only)

Status Menu

Unit 1 View

Status Menu – System View

Service Menu

Unit #

Password

Setpoints

Unit Diary

Standby Settings/Lead-Lag

Maintenance/Wellness Settings

Diagnostics / Service Mode

Set Alarms

Sensor Calibration/Setup

System/Network Setup

Options Setup

Servi ce Contact Info

Status Menu
Unit 2, 3, 4...

Advanced Menu

Unit #

Password

Factory Settings

Compressor Info

Access Passwords

8

Figure 8 User menu icons

Table 2 User menu icons

Icon Name

Description

Liebert iCOM Display Components and Functions

User Menu password: 1490

Available On Display

°C / °F

% RH

SET

EVENT

LOG

Setpoints

Spare Part List

Event Log Contains last 400 events Small & Large

Graphics Displays temperature and humidity graphs Small & Large

View Network Shows status of all connected units Large

View and change temperature and humidity
setpoints

Displays the various part numbers of the
components/parts in the cooling unit

Small & Large

Large

ALARMS

SET

SET

!

ACTIVE

ALARMS

1 2

6

1234h

Set Alarms Allows enable, disable and settings for alarms Small & Large

Sensor Data

Active Alarms

Display Setup

39

Total Run Hours

Shows readings of standard and optional
sensors

Allows the user to view all current active
alarms

Change settings for display: language, time,
simple or graphic view

Records the run time of all components and
allows setting of limits on run time

Small & Large

Small & Large

Small & Large

Small & Large

9

Table 2 User menu icons (continued)

Icon Name

Description

Liebert iCOM Display Components and Functions

Available On Display

1 2

6

Sleep Mode

39

Service Contact Info

Allows setback settings for non-peak
operation

Contains key contact information for local
service, including names and phone numbers

Small & Large

Small & Large

10

Figure 9 Service menu icons

Table 3 Service menu icons

Icon Name

°C / °F

% RH

Setpoints To view and change temperature and humidity setpoints Small & large

SET

Description

Liebert iCOM Display Components and Functions

Service Menu password: 5010

Available On

Display

WELLNESS

SERVICE

SET

ALARMS

+ / -

Unit Diary

Standby Settings/
Lead-Lag

Maintenance/
Wellness Settings

Diagnostics/
Service Mode

Set Alarms Allows enable, disable and settings for alarms Small & large

Sensor
Calibration/Setup

Shows all entered program changes and maintenance
performed on the unit

Allows lead/lag setup when multiple units are connected Small & large

Allows setting maintenance interval reminder,
maintenance message, number of unit starts and stops,
and time since last maintenance

Allows troubleshooting, manual mode, read analog and
digital inputs

Allows calibration of sensors Small & large

Large

Small & large

Small & large

NETWORK

System/Network
Setup

Options Setup Allows setup of component operation Small & large

Service Contact Info

Allows setup and U2U communication for multiple units Large

Contains key contact information for local service,
including names and phone numbers

11

Small & large

3.0 OPERATION

The Liebert iCOM display for your Liebert cooling unit features an easy-to-use, menu-driven liquid
crystal display (LCD). All unit settings and parameters can be viewed and adjusted through three
menus: User, Service and Advanced. All active alarms are displayed on the LCD and annunciated.

The control is shipped from the factory with default selections for all necessary settings. Adjustments
can be made if the defaults do not meet your requirements.

References to menu items in this manual are followed by the main menu and the submenu where they
can be found.

For example:

• Temperature Setpoint (User Menu, Setpoints) - The Temperature Setpoint parameter is
located in the User menu under the Setpoints submenu.

• High Return Humidity (Service Menu, Set Alarms) - The High Return Humidity alarm is
located in the Service menu under the Set Alarms submenu.

3.1 Single Unit Functions

3.1.1 Unit/Fan Control

Start - Stop

Operation

Unit on means the fan output is activated. The unit can be switched On and Off from two inputs:

1. Remote on/off input

2. Display button

Pressing the On/Off key on a small display will control only the cooling unit it is connected to regard­less, of whether the cooling unit is a stand-alone unit or part of a network.

Pressing the On/Off key on a large display of a stand-alone cooling unit will control only that unit.

The effect of pressing the On/Off key on a large display connected to a network depends on the view:
System or Unit.

• In System view, pressing the On/Off key shows a warning asking for confirmation to shut down
the entire system.

• In Unit view, pressing the On/Off key affects only the unit being viewed, without a confirmation
request.

Each time a unit is powered on or off, an event is added to the Event Log in the User menu.

NOTE

Customer switches: remote On/Off (if used) and display On/Off switches are in series. A
cooling unit will start only if both switches are On; if one of these switches is Off, the unit will
stop. Safety devices within the unit are also in series and will shut the unit down if required.

Figure 10 Start-stop priority switches

Remote On / Off

Display On / Off

NOTE

If Remote On/Off is not used, a jumper is inserted to bypass the switch.

12

Operation

Autorestart

When there is a loss of power to the cooling unit and power comes back, the unit will return to its pre­vious operating status—on if it was on before the power off, off if it was off.

When power returns, the autorestart time—time-selectable: Single Unit Auto Restart (Service Menu,
Options Setup)—controls the start of the unit. The autorestart time runs in a loop, starting the next
unit each time when elapsed, starting with Unit # 1.

Loss of Power Alarm

A Loss of Power Alarm is activated when power is restored after an interruption. If acknowledged, the
alarm resets automatically after 30 minutes. This alarm can be set to different event types (Message,
Alarm or Warning) and can be disabled under menu item Loss of Power (Service Menu, Set Alarms).

NOTE

Loss of power alarm will be activated only on units that had the fan on before power was lost.

Fan Alarm / Fan Protection Settings

The fan operation is protected by two digital devices: motor protection (optional) and a differential
pressure switch. The motor protection monitors for main fan overload and the differential pressure
switch ensures that the blower(s) are moving air. If either protection device triggers, an alarm will be
announced by a buzzer, alarm relay and event to monitoring after an adjustable time-delay (Main
Fan Overload and Loss Of Airflow in Service Menu, Set Alarms).

The time delay at the unit start is always five seconds shorter than the control delay (to avoid short
component starting when the fan is not working). During operation, the fan delay is fixed to
15 seconds.

There are two selection possibilities for both, Loss Of Airflow and Main Fan Overload:

• Shutdown—stops the unit (intended for DX models).

• Disable—stops the humidifier, electrical heaters and dehumidification; allows cooling and
free-cooling only (intended for chilled water models / external cooling).

NOTE

When the Main Fan Overload alarm is active, the Loss of Airflow alarm is masked out.

3.1.2 Chilled Water Units with Variable Speed Motor

VSD Fan Speed (Auto or Manual VSD Fan Speed Control)

The parameter VSD Fan Speed (Service Menu, Setpoints) allows the cooling unit's fan motor speed to
be set for:

• Auto operation: when set to Auto, the speed of the VSD (variable speed drive) motor follows the
position of the chilled water valve based on predetermined logic for cooling and dehumidification
operation.

• Manual operation: when set to Manual, the speed of the VSD motor follows user input as set
either locally at the cooling unit's Liebert iCOM display (under VSD Setpoint in Service Menu,
Setpoints) or remotely using Modbus BMS signal with an optional Liebert IntelliSlot

VSD Setpoint (VSD Fan Speed Setting)

If the VSD Fan Speed Control (Service Menu, Setpoints) is set for Manual, the VSD Fan Speed Set­point (Service Menu, Setpoints) may be set for the desired speed of the variable speed motor.

Depending on the product control design, there may be an internal minimum speed, as defined by
that specific product operation, while the customer input may be set for 0-100%:

• Fan speed may be set locally at the unit using the Liebert iCOM display.

• Fan speed may be set remotely via a BMS signal (sent via Modbus using an optional Liebert Intel­liSlot 485 card), which then transmits to the unit local control.

®

485 card.

13

3.1.3 General Compressor Requirements
Low-Pressure Time Delay

When the compressor starts, the low-pressure input is ignored for a selected period of time based on
the setting of the Low Pressure Alarm Delay (Service Menu, Options Setup). This time is usually set
to 3 minutes on air-cooled units, and to 0 or 1 minute on water cooled units. When this time is
expired, a second timer starts to operate if the low-pressure input is active. This second timer is active
during normal compressor operation to avoid compressor trips due to bubbles in the refrigerant or
other influences creating short trips of the low-pressure switch. The low-pressure switch input is
enabled only if the compressor is operating. Exception: Pump Down (see Pump Down).

NOTE

Low-pressure condition could be read through contacts or through pressure transducers with
threshold setting.

Pump Down

The Pump Down operation is performed to protect the compressor oil from being diluted with liquid
refrigerant to ensure that the compressor is properly lubricated for the next startup. The Pump Down
operation operates in the following manner:

Whenever a compressor is turned Off and the low-pressure switch is closed (pressure OK), the com­pressor will be operated with the LLSV (liquid line solenoid valve) closed (de-energized) until the low­pressure switch opens (low-pressure condition, without giving alarm). When there is a call to turn off
a compressor the LLSV is closed. If the low suction pressure switch (LPS) does not open within a spec­ified time, the LLSV is turned On then back Off (to try to unstick the LLSV). The control will then
wait a set period of time for the LPS to open. This will happen three times. If, after three times, the
low suction pressure switch does not open, the compressor and LLSV are locked off and an alarm
“Pump Down not completed” will appear.

Operation

There is a re-pump down if the LPS opens again after the compressor has been already stopped—a
maximum of six re-pump-down cycles per hour are allowed. At the seventh request of re-pump down
the alarm “Comp 1 Pumpdown Fail” or “Comp 2 Pumpdown Fail” will appear and the compressor will
be locked out.

Pump down is always performed loaded (for compressors with unloaders: unloaders off, digital scroll:
control solenoid valve disabled).

For digital scroll only: when pump down has finished successfully (LPS opened), pump down will be
continued for another half-second with the control solenoid valve energized.

High Pressure Alarm

When the compressor is initially activated, the system will be monitored for a high pressure situation.
When a high pressure situation is detected during the first 10 minutes of operation, the unit will
attempt to correct the problem several times without notification. If the unit is unsuccessful in cor­recting the problem, an alarm will occur and the affected compressor will be locked off. If high head
pressure alarm trips three times in a rolling 12 hour period, the affected compressor will be locked off.

After the compressor has been running for 10 minutes, if a high head pressure situation is detected,
an alarm will occur and the affected compressor will be immediately locked off without the unit trying
to correct the problem.

Once the compressor is locked off, it will not come back on until main power is reset, or until the
HP Alarm Counters (Service Menu, Diagnostics) are reset to 0. Setting the counter to 0 will auto-reset
the alarm without the need of pressing the reset button on the display. Even if the pressure in the
system drops below the alarm point, the compressor will remain off until the system is reset.

NOTE

If the unit is equipped with manual reset high head pressure switches, or if the auto reset high
head pressure switches don’t reset, the compressor will not be turned back on, but there will be
a 30-second delay from when the high head pressure situation occurs and when the alarm is
annunciated.

14

Digital Scroll High Temperature

A protective maximum operating compressor temperature limit is imposed on units with digital scroll
compressor(s) with thermistor. Once the digital scroll temperature reaches the maximum tempera­ture threshold, the compressor will be locked out for at least 30 minutes and an alarm will be annun­ciated. If after 30 minutes the temperature has cooled to a safe operating temperature, the
compressor will resume operation.

Each time a high-temperature alarm occurs, HT 1 Alarm Counter (Service Menu, Diagnostics) or
HT 2 Alarm Counter (Service Menu, Diagnostics) is increased by one. Once these counters reach five
occurrences in a rolling four-hour period, the compressor will be locked out. The alarm can be reset
once the temperature returns to a safe level by:

1. Setting the counter back to 0 from the display and pressing the alarm reset button.

2. Shutting off power to the control board by turning the cooling unit's main power disconnect switch

Off and On.

3.1.4 Compressor Timing—Units With Two Compressors

To help maximize the life of your compressor(s), there is a start-to-next start delay for each single
compressor.

A Minimum ON time and a Minimum Off time may be selected in the Advanced menu (minimum
three minutes for single phase compressors). Consult the factory on how to modify the Minimum ON
and OFF time settings.

Operation

3.1.5 Compressor Sequencing

Compressor Sequencing parameter (Service Menu, Options Setup) is intended to maintain equal run
times between compressors. This setting has three selection possibilities:

• Always use Compressor 1 as lead compressor

• Always use Compressor 2 as lead compressor

• Auto:

• First priority: if the safety timings are acceptable for only one compressor, then it is the next
to be started/stopped.

• If both compressors are off: the one with fewer working hours is the next to start.

• If both compressors are in operation: the one that has been operating longer since the last
start is the next to be stopped.

NOTE

The Auto setting attempts to maintain equal run times between compressors.

15

3.2 Temperature Control—Single Source Cooling (No Extra Cooling Coil)

3.2.1 Temperature Proportional Band

The control uses the temperature proportional band to determine which operation to perform (cool­ing/heating) and how intensely to perform it. The Temperature Proportional Band is a user-defined
range that is divided into two equal parts for cooling and heating. The Temperature Setpoint is
between these two equal parts.

An optional Temperature Deadband range can be defined, which is equally divided on either side of
the setpoint and separates the two halves of the proportional band. Figure 11 illustrates how the
temperature proportional band is evenly divided on either side of the temperature setpoint, with and
without a deadband.

Figure 11 Temperature proportional band

Without D eadband

Operation

-Temp + Temp

-Temp

-100%

Heating

Heati ng

-100%

Heating

½ Proportional Band

Setpoint

With Deadband

Dead -

band

0%

Setpoint

0%

½ Proportional Band½ Proportional Band

½ Proportional Band

0%

CoolingHeati ng

Cooling

+ 100%

Cooling

+ Temp

+ 100%

Cooling

When the return air temperature deviates from the setpoint it begins to penetrate one of the propor­tional band halves, cooling or heating. If the return air temperature increases, the control calls for 0%
(none) to 100% (full) cooling capacity based on how far the temperature penetrates the cooling portion
of the proportional band. If the return air temperature decreases, the control calls for 0% (none) to ­100% (full) heating capacity based on how far the temperature penetrates the heating portion of the
proportional band.

When the return air temperature reaches the end of the proportional band, either 100% or -100%, full
cooling or full heating capacity is provided. No operation is performed when a 0% call is calculated.
The control varies the call for cooling and heating in 1% increments as the return air temperature
moves through the proportional band halves.

The deadband range is used to widen the setpoint. When the return air temperature falls within the
deadband, the control operates the same as if the temperature equaled the setpoint exactly. This set­ting helps maximize component life by preventing excessive component cycling. The Temperature
Proportional Band and Temperature Deadband parameters are in the Service menu under the Set­points submenu. The Temperature Setpoint parameter is in both the User menu and Service Menu
under Setpoints.

There is a parameter AutoSet Enable (Service Menu, Setpoints), which automatically sets the propor­tional bands for temperature and humidity, and both the integration time factors according to the
type of unit (Chilled Water, single or double compressor), with influence of the selected Teamwork
Mode. See 4.1 - Teamwork Modes for more on using this feature.

16

3.2.2 Compressor Control

Depending on the type of Liebert air conditioning unit you have your unit may contain one or two
compressors with or without unloaders.

Compressor Proportional Bands

One Single-Step Compressor Without Unloaders—One-Step

One single-step compressor, Cool 1, is started at 100% call for cooling from the temperature propor­tional band and stopped at 0% (see Figure 12).

Figure 12 One single-step compressor without unloaders

Temp Setpoint : 70°F
Proportional Band: 8°F
Deadband: 2°F

Cool 1

Off

½ Dead-

band

Operation

Cool 1

On

75

+ 100 %

Cooling

0%

Cooling

71 72 73 7470

½ Proportional Band

Increasing Temperature

Two Single-Step Compressors Without Unloaders—Two-Step

First single-step compressor, Cool 1, is started at 50% calculated output from the temperature propor­tional band, and stopped at 0%. The second compressor, Cool 2, starts at 100% and stops at 50% (see

Figure 13).

One Compressor With an Unloader—Two-Step

The two-step compressor is started unloaded at 50%, Cool 1, calculated output from the temperature
proportional band and stopped at 0%. At 100% the compressor starts fully loaded, Cool 2, and returns
to unload operation at 50% (see Figure 13).

Figure 13 Two single-step compressors without unloaders or one compressor with an unloader (two-step)

Temp Setpoint: 70°F
Proportional Band: 8°F
Deadband : 2°F

1/2 D ead -

band

Cool 1

On

Cool 2

On

0%

Cooling

Cool 1

71 72 73 7470

Off

Cool 2

Off

1/2 Proportional Band

Increasing Temperature

17

75

+ 100%

Cooling

Two Compressors With Unloaders—Four-Step

The first two-step compressor is started unloaded at 33% calculated output from the temperature pro­portional band and stopped at 17%. At 80% Compressor 1 will be loaded, at 70% unloaded.

The second compressor starts unloaded at 63% and stops at 47%. At 100%, Compressor 2 will be
loaded, at 90% unloaded (see Figure 14).

The four stages of cooling are accomplished in the following manner:

• 1 stage: One compressor, unloaded - Cool 1

• 2 stages: Both compressors, unloaded - Cool 2

• 3 stages: One compressor, loaded and one compressor, unloaded - Cool 3

• 4 stages: Both compressors, loaded - Cool 4

Figure 14 Two compressors with unloaders (four-step)

Temp Setpoint: 70°F
Proportional Band: 8°F
Deadband : 2°F

½ Dead-

band

Cool 1

On

Cool 2

On

Cool 3

On

Operation

Cool 4

On

0%

Cooling

Cool 1

Off

Cool 3

Cool 2

Off

½ Proportional Band

Off

757473727170

+ 100%

Cool 4

Off

Increasing Temperature

Cooling

18