LG Display LP133WH1-TLB1 Specification
Global LCD Panel Exchange Center
www.panelook.com
LP133WH1
Liquid Crystal Display
Product Specification
SPECIFICATION
FOR
APPROVAL
()Preliminary Specification
() Final Specification
Title 13.3” WHD TFT LCD
BUYER HP
MODEL
APPROVED BY
/
/
SUPPLIER LG Display Co., Ltd.
*MODEL LP133WH1
Suffix TLB1
*When you obtain standard approval,
please use the above model name without suffix
APPROVED BY SIGNATURE
SIGNATURE
K. J. Kwon / S.Manager
REVIEWED BY
M. J. Lee / Manager
PREPARED BY
/
D. Y. KIM / Engineer
Product Engineering Dept.
Please return 1 copy for your confirmation with
your signature and comments.
Ver. 1.0 29, Jun, 2009
LG Display Co., Ltd
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
0/ 31
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
LP133WH1
Liquid Crystal Display
Product Specification
Contents
No ITEM
COVER
CONTENTS
RECORD OF REVISIONS
1 GENERAL DESCRIPTION
2 ABSOLUTE MAXIMUM RATINGS
3 ELECTRICAL SPECIFICATIONS
3-1 ELECTRICAL CHARACTREISTICS
3-2 INTERFACE CONNECTIONS
3-3 LVDS SIGNAL TIMING SPECIFICATIONS
3-4 SIGNAL TIMING SPECIFICATIONS
3-5 SIGNAL TIMING WAVEFORMS
3-6 COLOR INPUT DATA REFERNECE
3-7 POWER SEQUENCE
4 OPTICAL SFECIFICATIONS
Page
0
1
2
3
4
5-6
7-8
9-10
11
11
12
13
14-16
5 MECHANICAL CHARACTERISTICS
6 RELIABLITY
7 INTERNATIONAL STANDARDS
7-1 SAFETY
7-2 EMC
8 PACKING
8-1 DESIGNATION OF LOT MARK
8-2 PACKING FORM
9 PRECAUTIONS
A APPENDIX. Enhanced Extended Display Identification Data
Ver. 1.0 29, Jun, 2009
17-23
24
25
25
26
26
27-28
29-31
1/ 31
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
www.panelook.com
LP133WH1
Liquid Crystal Display
Product Specification
RECORD OF REVISIONS
Revision No Revision Date Page Description
0.0 29. Apr. 2009 - First Draft (Preliminary Specification) 0.0
1.0 29.Jun.2009 5-6 Electrical characteristics update
EDID
ver
Ver. 1.0 29, Jun, 2009
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
2/ 31
www.panelook.com
Global LCD Panel Exchange Center
1. General Description
The LP133WH1 is a Color Active Matrix Liquid Crystal Display with an integral LED backlight system. The
matrix employs a-Si Thin Film Transistor as the active element. It is a transmissive type display operating in
the normally white mode. This TFT-LCD has 13.3 inches diagonally measured active display area with
WHD resolution(1366 horizontal by 768 vertical pixel array). Each pixel is divided into Red, Green and Blue
sub-pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color
is determined with a 6-bit gray scale signal for each dot, thus, presenting a palette of more than 262,144
colors.
The LP133WH1 has been designed to apply the interface method that enables low power, high speed, low
EMI.
The LP133WH1 is intended to support applications where thin thickness, low power are critical factors and
graphic displays are important. In combination with the vertical arrangement of the sub-pixels, the
LP133WH1 characteristics provide an excellent flat display for office automation products such as Notebook
PC.
www.panelook.com
LP133WH1
Liquid Crystal Display
Product Specification
ڞک
ڧڱڟڮٻځ
گۄۈۄۉۂ
ڌ
ڰێۀۍٻھۊۉۉۀھۏۊۍٻ
ڞۊۉۏۍۊۇ
ڝۇۊھۆ
گڡگڈڧڞڟٻګڼۉۀۇ
ڃڌڎڑڑٻۓٻڒڑړڄ
ګڪڲڠڭٻ
ڝڧڪڞڦ
ڏڋ
ګۄۉ
ڮۊېۍھۀٻڟۍۄۑۀۍٻڞۄۍھېۄۏ
ڌڎڑڑ
ڠڟڤڟٻ
ڝڧڪڞڦ
ڧڠڟٻڝڼھۆۇۄۂۃۏٻڜێێ’۔
ڱڝڧچٻځٻګڲڨ
ڏڍۀڼ
ࣿࣜࣜ ࣜࣜࣜ
General Features
Active Screen Size 13.3 inches diagonal
Outline Dimension
Pixel Pitch
Pixel Format 1366 horiz. by 768 vert. Pixels RGB strip arrangement
Color Depth 6-bit, 262,144 colors
Luminance, White 200 cd/m
Power Consumption Total 4.5 Watt(Max.) @ LCM circuit 1.2 Watt(Max.), B/L input 3.3Watt(Max. with Driver)
Weight 350g(Max.)
Display Operating Mode Transmissive mode, normally white
Surface Treatment Haze 25%, Anti-Glare treatment of the front polarizer
RoHS Comply
&Halogen Free
Ver. 1.0 29, Jun, 2009
308.1 (H) Ý 183.6 (V) Ý 5.5(D, max.) mm
0.2148 mm Ý 0.2148 mm
2
(Typ., 5 points)
Yes
ڌ
ڢڼۏۀٻڤۉٻګڼۉۀۇ
ڒڑړڌ
3/ 31
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
www.panelook.com
Global LCD Panel Exchange Center
ɗ
2. Absolute Maximum Ratings
The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit.
www.panelook.com
LP133WH1
Liquid Crystal Display
Product Specification
Table 1. ABSOLUTE MAXIMUM RATINGS
Parameter Symbol
Power Input Voltage
Operating Temperature
Storage Temperature
Operating Ambient Humidity
Storage Humidity
VCC -0.3 4.0 Vdc at 25 r 5qC
TOP 050qC1
HST -20 60 qC1
HOP 10 90 %RH 1
HST 10 90 %RH 1
Values
Units Notes
Min Max
Note : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39
Wet Bulb
20
]
30
Temperature [
10
0
qC Max, and no condensation of water.
90% 80%
60
50
40
60%
Humidity[(%)RH]
40%
20%
10%
Storage
Operation
-20
10
20 30 40 50
60 70 800
Dry Bulb Temperature [ɗ]
Ver. 1.0 29, Jun, 2009
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
4/ 31
www.panelook.com
Global LCD Panel Exchange Center
3. Electrical Specifications
3-1. Electrical Characteristics
The LP133WH1 requires two power inputs. The first logic is employed to power the LCD electronics and to
drive the TFT array and liquid crystal. The second backlight is the input about LED B/L.with LED Driver.
www.panelook.com
LP133WH1
Liquid Crystal Display
Product Specification
Table 2. ELECTRICAL CHARACTERISTICS
Parameter Symbol
Unit Notes
Min Typ Max
LOGIC :
Values
Power Supply Input Voltage V
Mosaic I
CC 3.0 3.3 3.6 V 1
CC - 315 365 mA 2
Power Supply Input Current
Black I
Power Consumption P
Power Supply Inrush Current I
LVDS Impedance Z
CC_max 360 410 mA 3
CC -1.01.2W2
CC_P - - 1500 mA 4
eDP 90 100 110 ȍ 5
BACKLIGHT : ( with LED Driver)
LED Power Input Voltage V
LED Power Input Current I
LED Power Consumption P
LED Power Inrush Current I
LED 7.0 12.0 20.0 V 6
LED - 260 - mA 7
LED -3.13.3W7
LED_P - 2000 mA 8
PWM Duty Ratio 6 - 100 % 9
PWM Jitter
-
0 - 0.3 % 10
PWM Impedance Z
PWM Frequency F
PWM High Level Voltage V
PWM Low Level Voltage V
LED_EN Impedance Z
LED_EN High Voltage V
LED_EN Low Voltage V
PWM 20 40 60 Nȍ
PWM 200 - 1000 Hz 11
PWM_H
PWM_L
PWM 20 40 60 Nȍ
LED_EN_H 3.0 - 5.3 V
LED_EN_L 0-0.8V
2.1 3.3 5 V
0-0.8V
Life Time 12,000 - - Hrs 12
Ver. 1.0 29, Jun, 2009
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
5/ 31
www.panelook.com
Global LCD Panel Exchange Center
Note)
1. The measuring position is the connector of LCM and the test conditions are under 25ɗ, fv = 60Hz,
Black pattern.
2. The specified Icc current and power consumption are under
the Vcc = 3.3V , 25ɗ, fv = 60Hz condition whereas Mosaic pattern
is displayed and fv is the frame frequency.
3. This Spec. is the max load condition for the cable impedance designing.
4. The below figures are the measuring Vcc condition and the Vcc control block LGD used.
The Vcc condition is same the minimum of T1 at Power on sequence.
www.panelook.com
LP133WH1
Liquid Crystal Display
Product Specification
Rising time
Vcc
0V
5. This impedance value is needed to proper display and measured form eDP Tx to the mating connector.
6. The measuring position is the connector of LCM and the test conditions are under 25ɗ.
7. The current and power consumption with LED Driver are under the Vled = 12.0V , 25ɗ, Dimming of
Max luminance whereas White pattern is displayed and fv is the frame frequency.
8. The below figures are the measuring Vled condition
and the Vled control block LGD used.
VLED control block is same with Vcc control block.
90%
10%
0.5ms
3.3V
Rising time
V
LED
0V
10%
12.0V
90%
0.5ms
9. The operation of LED Driver below minimum dimming ratio may cause flickering or reliability issue.
10. If Jitter of PWM is bigger than maximum. It may cause flickering.
11. This Spec. is not effective at 100% dimming ratio as an exception because it has DC level equivalent
to 0Hz. In spite of acceptable range as defined, the PWM Frequency should be fixed and stable for
more consistent brightness control at any specific level desired.
12 The life time is determined as the time at which the typical brightness of LCD is 50% compare to that of
initial value at the typical LED current. These LED backlight has 6 strings on it and the typical current
of LED’s string is base on 20mA.
Ver. 1.0 29, Jun, 2009
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
6/ 31
www.panelook.com
Global LCD Panel Exchange Center
3-2. Interface Connections
This LCD employs one interface connections, a 40 pin connector is used for the module electronics interface
and LED Driver.
The electronics interface connector is a model 20455-040E-0x manufactured by I-PEX.
Table 3. MODULE CONNECTOR PIN CONFIGURATION (CN1)
Pin Symbol Description Notes
1 NC No connection
2 VCC Power Supply, 3.3V Typ.
3 VCC Power Supply, 3.3V Typ.
4 V EEDID DDC 3.3V power
5 NC No Connection
6 Clk EEDID DDC Clock
7 DATA EEDID DDC Data
8 Odd_R
9 Odd_R
10 GND Ground
11 Odd_R
12 Odd_R
13 GND Ground
14 Odd_R
15 Odd_R
16 GND Ground
17 Odd_CLKIN- Negative LVDS differential clock input
18 Odd_CLKIN+ Positive LVDS differential clock input
19 GND Ground
20 NC No Connection
21 NC No Connection
22 NC No Connection
23 NC No Connection
24 NC No Connection
25 NC No Connection
26 NC No Connection
27 NC No Connection
28 NC No Connection
29 NC No Connection
30 NC No Connection
31 VLED_GND LED Ground
32 VLED_GND LED Ground
33 VLED_GND LED Ground
34 NC No Connection
35 BLIM PWM for Luminance control
36 BL_On Backlight On/Off Control
37 NC No Connection
38 VLED LED Power Supply (7V-20V)
39 VLED LED Power Supply (7V-20V)
40 VLED LED Power Supply (7V-20V)
0- Negative LVDS differential data input
IN
0+ Positive LVDS differential data input
IN
1- Negative LVDS differential data input
IN
1+ Positive LVDS differential data input
IN
2- Negative LVDS differential data input
IN
2+ Positive LVDS differential data input
IN
www.panelook.com
Product Specification
LP133WH1
Liquid Crystal Display
1, Interface chips
1.1 LCD : SW, SW0624 (LCD Controller)
including LVDS Receiver
1.2 System : THC63LVDF823A
or equivalent
* Pin to Pin compatible with LVDS
2. Connector
2.1 LCD :20455-040E-0x, I-PEX
2.2 Mating : 20453-040T-0x, I-PEX
2.3 Connector pin arrangement
[W
or its compatibles
or equivalent.
X
[LCD Module Rear View]
Ver. 1.0 29, Jun, 2009
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
7/ 31
www.panelook.com
Global LCD Panel Exchange Center
The LED backlight connector is a model TF12-9S-0.5H, manufactured by Hirose or equivalent.
Table 4. BACKLIGHT CONNECTOR PIN CONFIGURATION (CN2)
Pin Symbol Description Notes
1
2
3
}OXSYSZS[S\S]P
}OXSYSZS[S\S]P
uj uGj
www.panelook.com
Product Specification
slkGhOwP
slkGhOwP
LP133WH1
Liquid Crystal Display
X
`
4
5
6
7
8
9
}X
}Y
}Z
}[
}\
}]
slkGjGOuP
slkGjGOuP
slkGjGOuP
slkGjGOuP
slkGjGOuP
slkGjGOuP
Ver. 1.0 29, Jun, 2009
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
8/ 31
www.panelook.com
Global LCD Panel Exchange Center
3-3. LVDS Signal Timing Specifications
3-3-1. DC Specification
LVDS -
LVDS +
www.panelook.com
LP133WH1
Liquid Crystal Display
Product Specification
|VID|
# |VID| = |(LVDS+) ˀ (LVDS-)|
= {(LVDS+) + (LVDS-)}/2
#V
0V
CM
Description
LVDS Differential Voltage |V
LVDS Common mode Voltage V
LVDS Input Voltage Range V
3-3-2. AC Specification
LVDS Clock
LVDS Data
t
SKEW
V
CM
Symb
ol
| 100 600 mV -
ID
CM
IN
t
1) 85MHz > Fclk ˻ 65MHz : -400 ~ +400
2) 65MHz > Fclk ˻ 25MHz : -600 ~ +600
SKEW(Fclk
= 1/T
Min Max Unit Notes
0.6 1.8 V -
0.3 2.1 V -
T
clk
)
clk
V
IN_MAXVIN_MIN
Description Symbol Min Max Unit Notes
t
SKEW
- 400 + 400 ps
85MHz > Fclk
65MHz
LVDS Clock to Data Skew Margin
t
SKEW
LVDS Clock to Clock Skew Margin (Even
to Odd)
Maximum deviation
of input clock frequency during SSC
Maximum modulation frequency
of input clock during SSC
t
SKEW_EO
F
DEV
F
MOD
Ver. 1.0 29, Jun, 2009
- 600 + 600 ps
-1/7 + 1/7 T
-
· 3
clk
%-
- 200 KHz -
65MHz > Fclk
25MHz
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory!
-
9/ 31
www.panelook.com
Loading...