LG Display LM240WU7-SLB1 Specification

Page 1
LM240WU7
Liquid Crystal Display
Product Specification
SPECIFICATION
FOR
APPROVAL
24.0WUXGA TFT LCDTitle
BUYER
MODEL
APPROVED BY
/
/
/
HP
SIGNATURE
DATE
LG Display Co., Ltd.SUPPLIER
LM240WU7*MODEL
SLB1SUFFIX
*When you obtain standard approval,
please use the above model name without suffix
APPROVED BY
H.S KIM / G.Manager
REVIEWED BY
J.Y LEE / Manager [C]
K.H MOON / Manager [M]
G.T KIM / Manager [P]
PREPARED BY
S.J Lee / Engineer
SIGNATURE
DATE
Please return 1 copy for your confirmation with
your signature and comments.
Ver. 0.5 Oct. 14 . 2009
MNT Products Engineering Dept.
LG Display Co., Ltd.
1/ 34
Page 2
Product Specification
Contents
LM240WU7
Liquid Crystal Display
PageITEMNo
COVER CONTENTS RECORD OF REVISIONS GENERAL DESCRIPTION1 ABSOLUTE MAXIMUM RATINGS2
ELECTRICAL SPECIFICATIONS3 ELECTRICAL CHARACTREISTICS3-1
INTERFACE CONNECTIONS3-2 SIGNAL TIMING SPECIFICATIONS3-3 SIGNAL TIMING WAVEFORMS3-4 COLOR INPUT DATA REFERNECE3-5 POWER SEQUENCE3-6 VLCD DIP CONDITION3-7 OPTICAL SFECIFICATIONS4
MECHANICAL CHARACTERISTICS5
1 2 3 4 5
6 6
9 14 15 16 17 18 19
25
RELIABLITY6 INTERNATIONAL STANDARDS7 SAFETY7-1 EMC7-2 ENVIRONMENT7-3 PACKING8 DESIGNATION OF LOT MARK8-1 PACKING FORM8-2
PALLET FORM8-3 PRECAUTIONS9
Ver. 0.5 Oct. 14 . 2009
26 27 27 27 27 28 28 29
30 31
2/ 34
Page 3
Product Specification
RECORD OF REVISIONS
LM240WU7
Liquid Crystal Display
Revision
No
PageRevision Date
First Draft (Preliminary)-Jun. 4. 20090.0 Change the Model Name (SLA1 SLB1)1Jun. 16. 20090.1 Update the General Features4Jul. 30. 20090.2 Update the Electircalcharacteristics6 Update the CNT Pin Configuration(#28 Change the NC Connection)9 Change the General Features about Power consumption4Aug. 27. 20090.3
Change Spec of Input current & Power consumption6 Update the optical characteristics19Oct. 1. 20090.4
Change the numerical formula of GSR20 Change relative luminance of zero gray 24
Update the mechanical drawing.27 Change note (number 10) of operating precautions (section 9-2)33 Change the variance of lamp voltage from ±10% to ±20% (Note 6)7Oct. 14. 20090.5
Description
Ver. 0.5 Oct. 14 . 2009
3/ 34
Page 4
LM240WU7
Liquid Crystal Display
Product Specification
1. General Description
LM240WU7 is a Color Active Matrix Liquid Crystal Display with anintegral Cold Cathode Fluorescent Lamp(CCFL) backlight system. The matrix employs a-Si Thin Film Transistor as the active element. It is a transmissivetype display operating in the normally black mode. It has a 24inch diagonally measured active display area with WUXGA resolution (1200 vertical by 1920horizontal pixel array) Each pixel is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes. Gray scale or the brightness of the sub-pixel color is determined with a 8-bit gray scale signal for each dot, thus, presenting a palette of more than 16,7M(True) colors. Ithas been designed to apply the 8Bit 2 port LVDS interface. It is intended to support displays where high brightness, super wide viewing angle, high color saturation, and high color are important.
LVDS
2port
CN1
(30pin)
+12.0V
General Features
+12.0V
V
Lamp
24.1 inches(61.13cm) diagonalActive Screen Size
546.4(H) x 352.0(V) x 35.7(D) mm(Typ.) * without inverterOutline Dimension
0.270 mm x 0.270 mmPixel Pitch
RGB
Timing
Controller
Power Circuit
Block
2 x 6Sockets (High)
Source Driver Circuit
S1 S1920
TFT -LCD Panel
(1920 × RGB × 1200 pixels)
Back light Assembly
(U-Shape 6CCFL)
1920 horiz. By 1200 vert. Pixels RGB stripes arrangementPixel Format 8-bit, 16,777,216 colorsColor Depth 400cd/m
2
( Center 1 points)Luminance, White View Angle Free (R/L 178(Typ.), U/D 178(Typ.))Viewing Angle(CR>10) Total 70.20Watt (Typ.) ( 7.20 Watt@VLCD, 63 Watt @Vlamp)Power Consumption 2830 g (typ.) Weight Transmissive mode, normally blackDisplay Operating Mode Hard coating(3H), Anti-glare treatment of the front polarizerSurface Treatment
Ver. 0.5 Oct. 14 . 2009
4/ 34
Page 5
LM240WU7
Liquid Crystal Display
Product Specification
2. Absolute Maximum Ratings
The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit.
Table 1. ABSOLUTE MAXIMUM RATINGS
Parameter Notes
Power Input Voltage Operating Temperature Storage Temperature Operating Ambient Humidity Storage Humidity
Symbol
Values
MaxMin
500TOP 60-20TST
Units
Vdc14-0.3VLCD
°C °C
%RH9010HOP %RH9010HST
at 25 ± 2°C
Note : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39 °C Max, and no condensation of water.
Note : 2. Maximum Storage Humidity is up to 40, 70% RH only for 4 corner light leakage Mura.
90%
60
60%
Wet Bulb Temperature [C]
10
0
20
50
40
40%
30
Humidity [(%)RH]
10%
Storage
Operation
1, 2
10 20 30 40 50 60 70 800-20 Dry Bulb Temperature [C]
Ver. 0.5 Oct. 14 . 2009
5/ 34
Page 6
LM240WU7
Liquid Crystal Display
Product Specification
3. Electrical Specifications
3-1. Electrical Characteristics
It requires two power inputs. One is employed to power the LCD electronics and to drive the TFT array and liquid crystal. The second input power for the CCFL, is typically generated by an inverter. The inverter is an external unit to the LCDs.
Table 2. ELECTRICAL CHARACTERISTICS
Parameter Symbol
MODULE :
Differential Impedance
LAMP :
at 25 °C
at 0 °C Operating Frequency Discharge Stabilization Time Power Consumption Life Time
Values
MaxTypMin
Vdc12.612.011.4VLCDPower Supply Input Voltage
ILCDPower Supply Input Current
Zm
11010090
1950(3.0mA)1750(6.0mA) 1550(8.0mA)VBLOperating Voltage
8.06.03.0IBLOperating Current
2500 2900
ohm
RMS
RMS
V
RMS
V
RMS
NotesUnit
1mV400VRFPermissive Power Input Ripple 2mA690600­3mA920800-
2Watt8.287.20-PLCDPower Consumption 4A3--IRUSHRush current
5, 6V
5mA
5,7VsEstablished Starting Voltage
8kHz805540fBL
5, 9Min3-Ts
10Watt69.363PBL
5, 11Hrs50,000
Note : The design of the inverter must have specifications for the lamp in LCD Assembly.
The performance of the Lamp in LCM, for example life time or brightness, is extremely influenced by the characteristics of the DC-AC inverter. So all the parameters of an inverter should be carefully designed so as not to produce too much leakage current fromhigh-voltage output of the inverter.
When you design or order the inverter, please make sure unwanted lighting caused by the mismatch of the lamp and the inverter (no lighting, flicker, etc) never occurs. When you confirm it, the LCD– Assembly should be operated in the same condition as installed in you instrument.
Ver. 0.5 Oct. 14 . 2009
6/ 34
Page 7
LM240WU7
Liquid Crystal Display
Product Specification
Note : Do not Insert conducting Material to lamp connecting socket. If the conducting Material is inserted
to the lamp connecting sockets, TFT-LCD Module has a low luminance and the inverter has abnormal
action. Because leakage current is occurred between lampconnecting socket and conducting material.
1. Permissive power ripple should be measured under V time, we recommend the bandwidth configuration of oscilloscope is to be under 20Mhz.
2. The specified current and power consumption are under the V whereas mosaic pattern(8 x 6) is displayed and fVis the frame frequency.
3. The current is specified at the maximum current pattern.
4. The duration of rush current is about 2ms and rising time of power Input is 1ms(min.).
5. Specified values are for a single lamp.
6. Operating voltage is measured at 25 ± 2°C. The variance of the voltage is ± 20%.
7. The voltage above VSshould be applied to the lamps for more than 1 second for start-up.
(Inverter open voltage must be more than lamp starting voltage.)
Otherwise, the lamps may not be turned on. The used lamp current is the lamp typical current.
8. The output of the inverter must have symmetrical (negative and positive) voltage waveform and
symmetrical current waveform (Unsymmetrical ratio is less than 10%). Please do not use the inverter which has unsymmetrical voltage and unsymmetrical current and spike wave. Lamp frequency may produce interface with horizontal synchronous frequency and as a result this may cause beat on the display. Therefore lamp frequency shall be as away possible from the horizontal synchronous frequency and from its harmonics in order to prevent interference.
9. Lets define the brightness of the lamp after being lighted for 5 minutes as 100%. TSis the time required for the brightness of the center of the lamp to be not less than 95%. The used lamp current is the lamp typical current.
10. The lamp power consumption shown above does not include loss of external inverter. The used lamp current is the lamp typical current. (PBL= VBLx IBLx N
11. The life is determined as the time at which brightness of the lamp is 50% compared to that of initial
value at the typical lamp current on condition of continuous operating at 25 ± 2°C.
12. Requirements for a system inverter design, which is intended to have a better display performance, a better power efficiency and a more reliable lamp, are following. It shall help increase the lamp lifetime and reduce leakage current.
a. The asymmetry rate of the inverter waveform should be less than 10%. b. The distortion rate of the waveform should be within 2 ±10%.
* Inverter output waveform had better be more similar to ideal sine wave.
=12.0V, 25 ± 2°C,fV=60Hzconditionand At that
LCD
=12.0V, 25 ± 2°C,fV=60Hz condition
LCD
)
Lamp
* Asymmetry rate:
I p
| I p– I –p| / I
rms
x 100%
* Distortion rate
I -p
I p(or I –p) / I
rms
13. The inverter which is combined with this LCM, is highly recommended to connect coupling(ballast)
condenser at the high voltage output side. When you use the inverter which has not coupling(ballast) condenser, it may cause abnormal lamp lighting because ofbiased mercury as time goes.
14. In case of edgy type back light with over 6 parallel lamps, input current and voltage wave form should
be synchronized
Ver. 0.5 Oct. 14 . 2009
7/ 34
Page 8
Product Specification
LM240WU7
Liquid Crystal Display
< Permissive Power Input Ripple (V
White Pattern
< Power consumption (V
Typical current pattern (White : 255Gray, Black : 0Gray)
LCD
=12.0V, 25 ± 2°C,fV=60Hz) >
LCD
Black Pattern
=12.0V, 25 ± 2°C,fV=60Hz) >
Maximum current pattern
Mosaic Pattern(8 x 6)
[ Figure 3 ] Mosaic pattern & Black Pattern for power consumption measurement
Ver. 0.5 Oct. 14 . 2009
White Pattern
8/ 34
Page 9
Liquid Crystal Display
Product Specification
3-2. Interface Connections
3-2-1. LCD Module
-LCD Connector(CN1) : IS100-L30B-C23 (UJU), KDF71G-30S-1H (Hirose )or Equivalent
-Mating Connector : FI-X30C2L (Manufactured by JAE) or Equivalent
Table 3 MODULE CONNECTOR(CN1) PIN CONFIGURATION
Symbol
SymbolNo
FR0M1
Minus signal of odd channel 0 (LVDS)
Description
No 16
SR1P
Plus signal of even channel 1 (LVDS)
Description
LM240WU7
FR0P2 FR1M3 FR1P4 FR2M5 FR2P6 GND7
FCLKINM8 FCLKINP9
FR3M10 FR3P11 SR0M12
Plus signal of odd channel 0 (LVDS) Minus signal of odd channel 1 (LVDS) Plus signal of odd channel 1 (LVDS) Minus signal of odd channel 2 (LVDS) Plus signal of odd channel 2 (LVDS) Ground Minus signal of odd clock channel
(LVDS) Plus signal of odd clock channel (LVDS) Minus signal of odd channel 3 (LVDS) Plus signal of odd channel 3 (LVDS) Minus signal of even channel 0 (LVDS)
17 18 19 20 21 22
23 24
25 26 27
GND SR2M SR2P SCLKINM SCLKINP
SR3M SR3P GND
OPEN OPEN PWM
Ground Minus signal of even channel 2 (LVDS) Plus signal of even channel 2 (LVDS) Minus signal of even clock channel (LVDS) Plus signal of even clock channel (LVDS) Minus signal of even channel 3 (LVDS)
Plus signal of even channel 3 (LVDS)
Ground NC NC
PWM_OUT for Wavy Noise ODC ON/OFF Control
SR0P13
Plus signal of even channel 0 (LVDS)
28
ODC ON
H : ODC ON , L : ODC OFF
(Connect High or Low.NoNC Condition) GND14 SR1M15
Ground Minus signal of even channel 1 (LVDS)
29 30
VLCD VLCD
Power Supply +12.0V
Power Supply +12.0V
Note: 1. All GND(ground) pins should be connected together and to Vss which should also be connected to
the LCDs metal frame.
2. All VLCD (power input) pins should be connected together.
3. Input Level of LVDS signal is based on the EIA 664 Standard. User Connector Diagram
1
30
#1 #30
Rear view of LCM
IS100-L30B-C23(UJU)
Ver. 0.5 Oct. 14 . 2009
9/ 34
Page 10
LM240WU7
Liquid Crystal Display
Product Specification
Table 4. REQUIRED SIGNAL ASSIGNMENT FOR Flat Link (TI:SN75LVDS83) Transmitter
Pin # Require SignalPin Name Pin # Require SignalPin Name
1 Power Supply for TTL InputVCC 29 Ground pin for TTLGND 2 TTL Input (R7)D5 30 TTL Input (DE)D26 3 TTL Input (R5)D6 31 TTL Level clock InputTXCLKIN 4 TTL Input (G0)D7 32 Power Down InputPWR DWN 5 Ground pin for TTLGND 33 Ground pin for PLLPLL GND 6 TTL Input (G1)D8 34 Power Supply for PLLPLL VCC 7 TTL Input (G2)D9 35 Ground pin for PLLPLL GND 8 TTL Input (G6)D10 36 Ground pin for LVDSLVDS GND
9 Power Supply for TTL InputVCC 37 Positive LVDS differential data output 3TxOUT3 10 TTL Input (G7)D11 38 Negative LVDS differential data output 3TxOUT3 11 TTL Input (G3)D12 39 Positive LVDS differential clock outputTXCLKOUT 12 TTL Input (G4)D13 40 Negative LVDS differential clock outputTXCLKOUT 13 Ground pin for TTLGND 41 Positive LVDS differential data output 2TXOUT2 14 TTL Input (G5)D14 42 Negative LVDS differential data output 2TXOUT2 15 TTL Input (B0)D15 43 Ground pin for LVDSLVDS GND 16 TTL Input (B6)D16 44 Power Supply for LVDSLVDS VCC 17 Power Supply for TTL InputVCC 45 Positive LVDS differential data output 1TXOUT1
46 Negative LVDS differential data output 1TXOUT118 TTL Input (B7)D17 19 TTL Input (B1)D18 20 TTL Input (B2)D19
22 TTL Input (B3)D20 23 TTL Input (B4)D21 24 TTL Input (B5)D22 25 TTL Input (RSVD)D23 26 Power Supply for TTL InputVCC 54 TTL Input (R2)D2
47 Positive LVDS differential data output 0TXOUT0
48 Negative LVDS differential data output 0TXOUT0
49 Ground pin for LVDSLVDS GND21 Ground pin for TTL InputGND
50 TTL Input (R6)D27
51 TTL Input (R0)D0
52 TTL Input (R1)D1
53 Ground pin for TTLGND
55 TTL Input (R3)D327 TTL Input (HSYNC)D24
56 TTL Input (R4)D428 TTL Input (VSYNC)D25
Notes : Refer to LVDS Transmitter Data Sheet for detail descriptions.
Ver. 0.5 Oct. 14 . 2009
10/ 34
Page 11
LVDS Input characteristics
1. DC Specification
LM240WU7
Liquid Crystal Display
Product Specification
LVDS Common mode Voltage LVDS Input Voltage Range
2. AC Specification
LVDS Clock to Data Skew Margin LVDS Clock to Clock Skew Margin (Even to
Odd)
CM
IN
SKEW
SKEW
SKEW_EO
-600
-1/7
NotesUnitMaxMinSymbolDescription
-mV600100|VID|LVDS Differential Voltage
-V1.80.6V
-V2.10.3V
NotesUnitMaxMinSymbolDescription
85MHz > Fclk 65MHzps+ 400-400t
ps+ 600t
65MHz > Fclk 25MHz
+ 1/7t
T
clk
-
Ver. 0.5 Oct. 14 . 2009
11/ 34
Page 12
Product Specification
< Clock skew margin between channel >
LM240WU7
Liquid Crystal Display
3. Data Format
1) LVDS 2 Port
< LVDS Data Format >
Ver. 0.5 Oct. 14 . 2009
12/ 34
Page 13
2) LVDS 1 Port
RCLK+
LM240WU7
Liquid Crystal Display
Product Specification
RA+/-
RB+/-
RC+/-
RD+/-
R3 R2
G4 G3
B5 B4
G7 G6
Previous(N-1)thCycle Next(N+1)thCycle
R1 R0
G2 G1
B3 B2
R7 R6
G0 R5 R4 R3 R2 R1 R0
B1 B0 G5 G4 G3 G2 G1
DE VSYNC HSYNC B5 B4 B3 B2
X B7 B6 G7 G6 R7 R6
Current(Nth) Cycle
G0
B1
DE
VSYNC HSYNC
X
R5 R4
B0 G5
B7 B6
Ver. 0.5 Oct. 14 . 2009
13/ 34
Page 14
LM240WU7
Liquid Crystal Display
Product Specification
3-3. Signal Timing Specifications
This is signal timing required at the input of the TMDS transmitter. All of the interface signal timing should be satisfied with the following specifications for its proper operation.
Table 5. TIMING TABLE (VESA COORDINATED VIDEO TIMING)
DCLK
Hsync
Vsync
Data
Period
Frequency
Period
Width-Active
Period
Frequency
Width-Active
Horizontal Valid
Horizontal Back Porch
Horizontal Front Porch
Horizontal Blank
SYMBOL
NoteUnitMaxTypMinITEM
ns13.1612.9812.82tCLK
MHz787776fCLK
104410401036tHP
tCLK
161616tWH
tHP123712351233tVP
Hz6159.9558.85fV
666tWV
960960960tHV
444036tHBP
282420tHFP
tHP
tCLK
Pixel frequency
: Typ. 154MHz
tWH+ tHBP+ tHFP848076-
Enable
Vertical Valid
Vertical Back Porch
Vertical Front Porch
Vertical Blank
-
120012001200tVV
272625tVBP
tHP
432tVFP
tWV+ tVBP+ tVFP373533
Note: Hsyncperiod and Hsyncwidth-active should be even number times of tCLK. If thevalue is odd number
times of tCLK, display control signal can be asynchronous.In order tooperate this LCM a Hsync,
Vsyn, and DE(data enable) signals should be used.
1. The performance of the electro-optical characteristics may be influenced by variance of the vertical refresh rates.
2. Vsyncand Hsyncshould be keep the above specification.
3. HsyncPeriod, HsyncWidth, and Horizontal Back Porch should be any times of of character
number(8).
4. The polarity of Hsync, Vsyncis not restricted.
Ver. 0.5 Oct. 14 . 2009
14/ 34
Page 15
3-4. Signal Timing Waveforms
LM240WU7
Liquid Crystal Display
Product Specification
Hsync, Vsync, DE, DATA
t
CLK
Dclk
INVALID
DATA
DE(Data Enable)
Hsync
t
WH
0.5VDD
0.7VDD
0.3VDD
VALID
Data are latched at the falling edge of DCLK
t
HP
INVALID
t
HBP
DE(Data Enable)
t
WV
Vsync
t
VBP
DE(Data Enable)
Ver. 0.5 Oct. 14 . 2009
t
HV
t
VP
t
VV
t
t
HFP
VFP
15/ 34
Page 16
LM240WU7
Liquid Crystal Display
Product Specification
3-5. Color Input Data Reference
The Brightness of each primary color(red,green,blue) is based onthe 8-bit gray scale data input for the color; the higher the binary input, the brighter the color. The table below provides a reference for color versus data input.
Table 6. COLOR DATA REFERENCE
Input Color Data
Basic
Color
RED
Color
Black 0 0 0 0 0 0 0 00 0 0 0 0 0 0 00 0 0 0 0 0 0 0 Red (255) Green (255) Blue (255) Cyan
Magenta Yellow
White
MSB LSB
RED
GREEN
MSB LSB
BLUE
MSB LSB
B7 B6 B5 B4 B3 B2 B1 B0G7 G6 G5 G4 G3 G2 G1 G0R7 R6 R5 R4 R3 R2 R1 R0
0 0 0 0 0 0 0 00 0 0 0 0 0 0 01 1 1 1 1 1 1 1 0 0 0 0 0 0 0 01 1 1 1 1 1 1 10 0 0 0 0 0 0 0 1 1 1 1 1 1 1 10 0 0 0 0 0 0 00 0 0 0 0 0 0 0 1 1 1 1 1 1 1 11 1 1 1 1 1 1 10 0 0 0 0 0 0 0 1 1 1 1 1 1 1 10 0 0 0 0 0 0 01 1 1 1 1 1 1 1 0 0 0 0 0 0 0 01 1 1 1 1 1 1 11 1 1 1 1 1 1 1
1 1 1 1 1 1 1 11 1 1 1 1 1 1 11 1 1 1 1 1 1 1 0 0 0 0 0 0 0 00 0 0 0 0 0 0 00 0 0 0 0 0 0 0RED (000) Dark
0 0 0 0 0 0 0 00 0 0 0 0 0 0 00 0 0 0 0 0 0 1RED (001)
............
0 0 0 0 0 0 0 00 0 0 0 0 0 0 01 1 1 1 1 1 1 0RED (254) 0 0 0 0 0 0 0 00 0 0 0 0 0 0 01 1 1 1 1 1 1 1RED (255) 0 0 0 0 0 0 0 00 0 0 0 0 0 0 00 0 0 0 0 0 0 0GREEN (000) Dark
GREEN
BLUE (000) Dark
BLUE
Ver. 0.5 Oct. 14 . 2009
0 0 0 0 0 0 0 00 0 0 0 0 0 0 10 0 0 0 0 0 0 0GREEN (001)
............
0 0 0 0 0 0 0 01 1 1 1 1 1 1 00 0 0 0 0 0 0 0GREEN (254) 0 0 0 0 0 0 0 01 1 1 1 1 1 1 10 0 0 0 0 0 0 0GREEN (255)
0 0 0 0 0 0 0 00 0 0 0 0 0 0 00 0 0 0 0 0 0 0 0 0 0 0 0 0 0 10 0 0 0 0 0 0 00 0 0 0 0 0 0 0BLUE (001)
............
1 1 1 1 1 1 1 00 0 0 0 0 0 0 00 0 0 0 0 0 0 0BLUE (254) 1 1 1 1 1 1 1 10 0 0 0 0 0 0 00 0 0 0 0 0 0 0BLUE (255)
16/ 34
Page 17
3-6. Power Sequence
LM240WU7
Liquid Crystal Display
Product Specification
V
LCD
90%
90%
Power Supply, V
LCD
Interface Signal, V (Digital RGB signal, SCDT ,V
sync
, H
sync
, DE,
i
0V
0V
Clock to PanelLink Transmitter)
Power Supply for Backlight Inverter
Table 7. POWER SEQUENCE
Parameter
10%
T1
T2 T5 T7
T6
10%
Valid Data
T3
LAMP ONLAMP OFF
Values
T4
MaxTypMin
LAMP OFF
Units
Notes : 1. Please avoid floating state of interface signal at invalid period.
2. When the interface signal is invalid, be sure to pull down the power supply for LCD V
3. Lamp power must be turn on after power supply forLCD and interface signal are valid.
Ver. 0.5 Oct. 14 . 2009
ms10-0.5T1
ms50-0.01T2
ms--500T3
--200T4
ms
ms50-0.01T5
ms-1000T7
to0V.
LCD
17/ 34
Page 18
3-7. VLCD Power Dip Condition
[ Figure 2 ] Power dip condition
Product Specification
t
d
V
V
LCD_dip
LM240WU7
Liquid Crystal Display
LCD
Dip condition
VLCD_dip V
X 0.2, td≤20ms
LCD_typ
Ver. 0.5 Oct. 14 . 2009
18/ 34
Page 19
LM240WU7
Liquid Crystal Display
Product Specification
4. Optical Specifications
Optical characteristics are determined after the unit has been ONfor approximately 30 minutes in a dark environment at 25±2°C. The values specified are at an approximate distance 50cm fromthe LCD surface at a viewing angle of Φ and θ equal to 0 ° and aperture 1 degree.
FIG 3 presents additional information concerning the measurement equipment and method.
Optical Stage(x,y)
LCD Module
[ FIG 3 ] Optical Characteristic Measurement Equipment and Method
Table 8. OPTICAL CHARACTERISTICS
SymbolParameter
Surface Luminance, white Luminance Variation
Response Time
Gray to Gray
RED
GREEN
Color Coordinates [CIE1931]
(By PR650)
BLUE
WHITE
Color Shift (Avg. Δu’v< 0.02)
Horizontal Vertical
Viewing Angle (CR>10) General
GSR @ 60dgree (Gamma shift rate)
Horizontal
Vertical Horizontal Vertical
WH
δ
WHITE GTG_AVR GTG_MAX
Rx
θ
CST_H
θ
CST_V
θ θ
δ
Gamma_H
δ
Gamma_V
PR 880 or RD 80S
or PR 650
50cm
(Ta=25 °C, V
Typ
-0.03
H V
=12.0V, fV=60Hz Dclk=154MHz, VBR=3.3V)
LCD
Values
400320L
MaxTypMin
2
NotesUnits
ms125-T ms-13-T
0.644
0.335Ry
0.304Gx
0.613Gy
0.146Bx
Typ
+0.03
0.070By
0.313Wx
0.329Wy
-140-
-100-
-178170
-178170 20-­20--
%-82-Color gamut (CG, CIE1976)
11000700CRContrast Ratio 2cd/m 3%75
4
5Degree
6Degree
7% 8K+700G255 CCT-300-WPT (White Point Tracking)
92.2Gray Scale
Ver. 0.5 Oct. 14 . 2009
19/ 34
Page 20
Product Specification
Notes 1. Contrast Ratio(CR) is defined mathematically as : (By PR880)
RatioContrast =
It is measured at center point(Location P1)
2. Surface luminance(LWH)is luminance value at 5 points average across the LCD surface 50cm from the surface with all pixels displaying white. For more information see FIG 2. (By PR880)
L
= = Average[ Lon1,Lon2,Lon3,Lon4,Lon5]
WH
3. The variation in surface luminance , δ WHITE is defined as : (By PR880)
LM240WU7
Liquid Crystal Display
pixels white all with Luminance Surface
pixels black all with Luminance Surface
=
δ
WHITE
Where L1to L9 are the luminance with all pixels displaying white at 9 locations.
For more information see FIG 2.
4. Gray to gray response time is the time required forthe display to transition from gray to gray. For additional information see Table 10. (By RD80S)
5. Color shift is the angle at which the average colordifference for all Macbeth is lower than 0.02.
For more information see FIG 3 and FIG 4. (By EZ Contrast)
-Color difference (Δuv)
x
u
'
=
4
v
'
++
yx
3122
24
1∑=
i
)''(
=
vuAvg
=
)''(
ivu
)L .. ,L,Minimum(L
P9P2P1
100
×
)L .... ,L ,(L Maximum
P9P2P1
y
9
++
yx
3122
u1, v1 : uvvalue at viewing angle direction u2, v2 : uvvalue at front (θ=0)
i : Macbeth chart number (Define 22 page)
2
21
2
)''()''('' vvuuvu +=
21
24
-Pattern size : 25% Box size
-Viewing angle direction of color shift : Horizontal, Vertical
6. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are
determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which
is normal to the LCD surface. For more information see FIG 4.(By PR880)
7. GSR is the rate of gamma shift at up, down, left and right 60 degree viewing angle compare with center gamma. For more information see FIG 5 and FIG 6 (By EZ Contrast)
-GSR (δ
8. WPT (White Point Tracking) is the variation of color temperature between G255 and G63.
(By PR650)
Ver. 0.5 Oct. 14 . 2009
) is defined as :
Gamma
 
1 ×
=GSR
 
Degree) 60Light Reft, Down, (Up, Value Gamma angle View
Degree) (0 Value GammaCenter
 
100
 
20/ 34
Page 21
Product Specification
Notes9. Gray scale specification
Gamma Value is approximately 2.2. For more information see Table 11.
Measuring point for surface luminance & measuring point for luminance variation.
H
LM240WU7
Liquid Crystal Display
H/2
P2
P5
V/2
V
V/10
The gray to gray response time is defined as the following figure and shall be measured by switching the
input signal for Gray To Gray”.
-Gray step : 5 step
-TGTG_AVR is the total average time at rising time and falling time for Gray To Gray”.
-TGTG_MAX is the max time at rising time or falling time for Gray To Gray”.
-In case of the difference in measured values due to the difference of measuring device or program was found, correlated value will be used after discussions between both parties.
P7
FIG. 2 Measure Point for Luminance
P3
P1
P8
H/10
P4
P6
P9
H : 518.4 mm V : 324.0 mm
Table 10. Gray to gray response time table
Gray to Gray
G1023
G767
Falling Time
Ver. 0.5 Oct. 14 . 2009
G511 G255
G0
Rising Time
G0G255G511G767G1023
21/ 34
Page 22
Product Specification
Color shift is defined as the following test pattern and color.
FIG. 3 Color Shift Test Pattern
Average RGB values in Bruce RGB for Macbeth Chart
LM240WU7
Liquid Crystal Display
25% Box size
Bluish greenBlue flowerFoliageBlue skyLight skinDark skin
459519311343827395R 799475411451571227G 715743187647495183B
Orange yellowYellow greenPurpleModerate redPurplish blueOrange
923643307847227879R 651775159271279419G 11923534735169999B
cyanMagentaYellowRedGreenBlue
143831967791291107R 507251851111595131G 691607147151263583B
blackNeutral 3.5Neutral 5Neutral 6.5Neutral 8White
91255443623827963R 91255443623827963G 91255443623827963B
Ver. 0.5 Oct. 14 . 2009
22/ 34
Page 23
Dimension of viewing angle range.
LM240WU7
Liquid Crystal Display
Product Specification
φ
= 180°, Left
φ
= 270°, Down
Normal
E
θ
φ
FIG. 4 Viewing angle
Y
φ
= 90°, Up
φ
= 0°, Right
FIG. 5 Sample Luminance vs. gray scale
(using a 256 bit gray scale)
Here the Parameter α and γ relate the signal level V to the luminance L. The GAMMA we calculate from the log-log representation (FIG. 6)
Ver. 0.5 Oct. 14 . 2009
FIG. 6 Sample Log-log plot of luminance
vs. gray scale
r
LaVL +=
b
b
+=
)log()log()log( aVrLL
23/ 34
Page 24
Table 10. Gray Scale Specification
LM240WU7
Liquid Crystal Display
Product Specification
Relative Luminance [%] (Typ.)Gray Level
0.10
31 63 95
127 159 191 223 255
1.2
4.7
11.7
21.2
35.2
53.0
75.4 100
Ver. 0.5 Oct. 14 . 2009
24/ 34
Page 25
LM240WU7
Liquid Crystal Display
Product Specification
5. Mechanical Characteristics
The contents provide general mechanical characteristics. In addition the figures in the next page are detailed mechanical drawing of the LCD.
546.4mmHorizontal
Outline Dimension
Bezel Area
Active Display Area
Surface Treatment
2830 g(Typ) / 2970 g(Max)Weight Hard coating(3H)
Anti-glare treatment of the front polarizer
352.0mmVertical
35.7mmDepth
522.4mmHorizontal
328.0mmVertical
518.4mmHorizontal
324.0mmVertical
Notes : Please refer to a mechanic drawing in terms of toleranceat the next page.
Ver. 0.5 Oct. 14 . 2009
25/ 34
Page 26
<FRONT VIEW>
LM240WU7
Liquid Crystal Display
Product Specification
Ver. 0.5 Oct. 14 . 2009
26/ 34
Page 27
<REAR VIEW>
LM240WU7
Liquid Crystal Display
Product Specification
Ver. 0.5 Oct. 14 . 2009
27/ 34
Page 28
6. Reliability
Environment test condition
5
Vibration test (non-operating)
LM240WU7
Liquid Crystal Display
Product Specification
ConditionTest ItemNo
Ta= 60°C 240hHigh temperature storage test1
Ta= -20°C 240hLow temperature storage test2
Ta= 50°C 50%RH 240hHigh temperature operation test3
Ta= 0°C 240hLow temperature operation test4 Wave form : random
Vibration level : 1.0G RMS Bandwidth : 10-300Hz Duration : X,Y,Z, 10 min
One time each direction
Shock level : 100G
6
8
9
Shock test (non-operating)
Humidity condition Operation7
Altitude
storage / shipment
Maximum Storage Humidity for 4 corner light leakage Mura.
Waveform : half sine wave, 2ms Direction : ±X, ±Y, ±Z
One time each direction
Ta= 40 °C ,90%RH
0 -40,000 feet(12192m)
Max 70%RH , Ta=40
Ver. 0.5 Oct. 14 . 2009
28/ 34
Page 29
LM240WU7
Liquid Crystal Display
Product Specification
7. International Standards 7-1. Safety
a) UL 60950-1:2003, First Edition, Underwriters Laboratories, Inc.,
Standard for Safety of Information Technology Equipment.
b) CAN/CSA C22.2, No. 60950-1-03 1stEd. April 1, 2003, Canadian Standards Association,
Standard for Safety of Information Technology Equipment.
c) EN 60950-1:2001, First Edition,
European Committee for ElectrotechnicalStandardization(CENELEC) European Standard for Safety of Information Technology Equipment.
7-2. EMC
a) ANSI C63.4 Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and
Electrical Equipment in the Range of 9kHZ to 40GHz. American National Standards Institute(ANSI), 1992
b) C.I.S.P.R Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.International Special Committee on Radio Interference.
c) EN 55022 Limits and Methods of Measurement of Radio Interface Characteristics of Information
Technology Equipment.European Committee for ElectrotechnicalStandardization.(CENELEC), 1998
( Including A1: 2000 )
7-3. Environment
a) RoHS. Directive 2002/95/EC of the European Parliament and of the Council on the reduction of the
use of certain hazardous substances in electrical and electronic equipment. January 2003
Ver. 0.5 Oct. 14 . 2009
29/ 34
Page 30
8. Packing
8-1. Designation of Lot Mark
a) Lot Mark
A B C D E F G H I J K L M
A,B,C : SIZE(INCH) D : YEAR E : MONTH F ~ M : SERIAL NO.
Note
1. YEAR
LM240WU7
Liquid Crystal Display
Product Specification
Year
Mark
2006720078200892009
6
321
200452005
4
200320022001
2010
2. MONTH
Month
Mark
Apr5May
4
Jun
6
Jul8Aug9Sep
7
b) Location of Lot Mark
Serial No. is printed on the label. The label is attached to thebackside of the LCD module. This is subject to change without prior notice.
0
Oct
A
Nov
B
DecMarFebJan
C321
Ver. 0.5 Oct. 14 . 2009
30/ 34
Page 31
8-2. Packing Form
a) Package quantity in one box : 5EA b) Box Size : 436 X 346 X 628
LM240WU7
Liquid Crystal Display
Product Specification
Ver. 0.5 Oct. 14 . 2009
31/ 34
Page 32
8-3. Pallet Form
LM240WU7
Liquid Crystal Display
Product Specification
Ver. 0.5 Oct. 14 . 2009
MATERIALDESCRIPTIONNO.
PACKING ASSY1
PALLET2
TAPE5
BAND6
BAND, CLIP7
Paper_1030X870X130
SWR4ANGLE, PACKING3
YUPO PAPERLABEL4
OPP
PP
CLIP 18MM
32/ 34
Page 33
LM240WU7
Liquid Crystal Display
Product Specification
9. PRECAUTIONS
Please pay attention to the followings when you use this TFT LCDmodule.
9-1. MOUNTING PRECAUTIONS
(1) You must mount a module using holes arranged in four cornersor four sides. (2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to the
module. And the case on which a module is mounted should have sufficient strength so that external force is not transmitted directly to the module.
(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.
Transparent protective plate should have sufficient strength in order to the resist external force. (4) You should adopt radiation structure to satisfy the temperature specification. (5) Acetic acid type and chlorine type materials for the cover case are not desirable because the former
generates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit break by electro-chemical reaction.
(6) Do not touch, push or rub the exposed polarizerswith glass, tweezers or anything harder than HB
pencil lead. And please do not rub with dust clothes with chemical treatment.
Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimental
to the polarizer.) (7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials like
chamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the adhesives used to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they cause chemical damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.
9-2. OPERATING PRECAUTIONS
(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage:
V=±200mV(Over and under shoot voltage) (2) Response time depends on the temperature.(In lower temperature, it becomes longer.) (3) Brightness depends on the temperature. (In lower temperature, it becomes lower.)
And in lower temperature, response time(required time that brightness is stable after turned on) becomes
longer. (4) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer or
electrical contacted parts. And after fading condensation, smearor spot will occur. (5) When fixed patterns are displayed for a long time, remnant image is likely to occur. (6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall be
done by system manufacturers. Grounding and shielding methods may be important to minimized the
interference. (7) Please do not give any mechanical and/or acoustical impact to LCM. Otherwise, LCM cant be operated
its full characteristics perfectly.
(8) A screw which is fastened up the steels should be a machine screw.
(if not, it causes metallic foreign material and deal LCM afatal blow) (9)Please do not set LCD on its edge.
(10) When LCMsare used for public display defects such as Yogure, image sticking can not be guarantee.
Ver. 0.5 Oct. 14 . 2009
33/ 34
Page 34
LM240WU7
Liquid Crystal Display
Product Specification
9-3. ELECTROSTATIC DISCHARGE CONTROL
Since a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain that treatment persons are connected to ground through wrist band etc. And dont touch interface pin directly.
9-4. PRECAUTIONS FOR STRONG LIGHT EXPOSURE
Strong light exposure causes degradation of polarizer and color filter.
9-5. STORAGE
When storing modules as spares for a long time, the following precautions are necessary. (1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature
between 5°C and 35°C at normal humidity.
(2) The polarizer surface should not come in contact with any other object.
It is recommended that they be stored in the container in which they were shipped.
9-6. HANDLING PRECAUTIONS FOR PROTECTION FILM
(1) The protection film is attached to the bezel with a small masking tape.
When the protection film is peeled off, static electricity is generated between the film and polarizer. This should be peeled off slowly and carefully by people who are electrically grounded and with well ion­blown equipment or in such a condition, etc.
(2) When the module with protection film attached is stored for a long time, sometimes there remains a very
small amount of glue still on the bezel after the protection film is peeled off.
(3) You can remove the glue easily. When the glue remains on thebezel surface or its vestige is recognized,
please wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal­hexane.
Ver. 0.5 Oct. 14 . 2009
34/ 34
Loading...