Please read this installation manual completely before installing the product.
Installation work must be performed in accordance with the national wiring standards
by authorized personnel only.
Please retain this installation manual for future reference after reading it thoroughly.
[Representative] LG Electronics Inc. EU Representative :
LG Electronics European Shared Service Center B.V.
Krijgsman 1, 1186 DM Amstelveen, The Netherlands
[Manufacturer] LG Electronics Inc. Changwon 2nd factory 84, Wanam-ro,
Seongsan-gu, Changwon-si, Gyeongsangnam-do, KOREA
This manual is the simplified version of original manual.
You can obtain the original manual from www.lg.com.
PORTUGUÊS
MALTI
SLOVENČINA
SLOVENŠČINA
LATVIEŠU VALODA
LIETUVIŲ KALBA
GAEILGE
ENGLISHITALIANOESPAÑOLFRANÇAISDEUTSCH
MAGYAR
БЪЛГАРСKN
SRPSKI
HRVATSKI
ΕΛΛΗΝΙΚΆ
SVENSKA
МАКЕДОНСКИ
SHQIP
ÍSLENSKABOSANSKI
ČEŠTINA
NORSKSUOMIDANSK
NEDERLANDS
POLSKI
LIMBA ROMÂNĂ
EESTI KEEL
ENGLISH
MODEL DESIGNATION
2
MODEL DESIGNATION
Product information
- Product Name : Air conditioner
- Model Name :
SQSMN B 015
- Additional Information : serial number is
refer to the barcode on the product.
Ex) 7,000 Btu/h Class → '07',
18,000 Btu/h Class → '18'
Product type
S : Wall mounted /
ARTCOOL mirror
J : Wall mounted
A : ARTCOOL
T : Ceiling Cassette
B, M : Ceiling Concealed Duct
V : Ceiling Suspended & floor
Q : Console
P : Floor Standing
Connectable Outdoor unit type
M : Indoor units only for
Multi systems
U : Indoor units only for
Single A systems
C : Common Indoor Unit for
Multi and Single CAC
Airborne Noise Emission
The A-weighted sound pressure emitted by
this product is below 70 dB.
** The noise level can vary depending on the
site.
The figures quoted are emission level and are
not necessarily safe working levels.
Whilst there is a correlation between the
emission and exposure levels, this cannot be
used reliably to determine whether or not
further precautions are required.
Factor that influence the actual level of
exposure of the workforce include the
characteristics of the work room and the other
sources of noise, i.e. the number of
equipment and other adjacent processes and
the length of time for which an operator
exposed to the noise. Also, the permissible
exposure level can vary from country to
country.
This information, however, will enable the
user of the equipment to make a better
evaluation of the hazard and risk.
Limiting concentration
Limiting concentration is the limit of Freon gas
concentration where immediate measures can
be taken without hurting human body when
refrigerant leaks in the air. The limiting
concentration shall be described in the unit of
3
(Freon gas weight per unit air volume)
kg/m
for facilitating calculation
Limiting concentration: 0.44kg/m3(R410A)
Refrigerant
concentration
(kg/m3)
Total amount of replenished
refrigerant in refrigerant facility (kg)
=
Capacity of smallest room where
indoor unit is installed (m3)
IMPORTANT SAFETY INSTRUCTIONS
3
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
Always comply with the following precautions to avoid dangerous situations and ensure
peak performance of your product
WARNING
!
It can result in serious injury or death when the directions are ignored
CAUTION
!
It can result in minor injury or product damage when the directions are ignored
WARNING
!
• Installation or repairs made by unqualified persons can result in hazards to you and
others.
• Installation work must be performed in accordance with the National Electric Code by
qualified and authorized personnel only.
• The information contained in the manual is intended for use by a qualified service
technician familiar with safety procedures and equipped with the proper tools and test
instruments.
• Failure to carefully read and follow all instructions in this manual can result in equipment
malfunction, property damage, personal injury and/or death.
Installation
• Do not use a defective or underrated circuit breaker. Use the correctly rated breaker and
fuse. There is risk of fire or electric shock.
• For electrical work, contact the dealer, seller, a qualified electrician, or an Authorized
Service Center. Do not disassemble or repair the product by yourself. There is risk of fire
or electric shock.
• Always ground the product as per the wiring diagram. Do not connect the ground wire to
gas or water pipes lightening rod or telephone ground wire. There is risk of fire or electric
shock.
• Install the panel and the cover of control box securely. There is risk of fire or electric
shock due to dust, water etc.
• Use the correctly rated breaker or fuse. There is risk of fire or electric shock.
• Do not modify or extend the power cable. If the power cable or cord has scrathes or skin
peeled off or deteriorated then it must be replaced. There is risk of fire or electric shock.
• For installation, removal or reinstall, always contact the dealer or an Authorized Service
Center. There is risk of fire, electric shock, explosion, or injury.
• Do not install the product on a defective installation stand. Be sure that the installation
area does not deteriorate with age. It may cause product to fall.
• Never install the outdoor unit on a moving base or a place from where it can fall down.
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
4
The falling outdoor unit can cause damage or injury or even death of a person.
• In outdoor unit the step-up capacitor supplies high voltage electricity to the electrical
components. Be sure to discharge the capacitor completely before conducting the repair
work.
An charged capacitor can cause electrical shock.
• When installing the unit, use the installation kit provided with the product. Otherwise the
unit may fall and cause severe injury.
• Indoor/outdoor wiring connections must be secured tightly and the cable should be
routed properly so that there is no force pulling the cable from the connection terminals.
Improper or loose connections can cause heat generation or fire.
• Safely dispose off the packing materials. Like screws, nails, batteries, broken things etc
after installation or svc and then tear away and throw away the plastic packaging bags.
Children may play with them and cause injury.
• Be sure to check the refrigerant to be used. Please read the label on the product.
Incorrect refrigerant used can prevent the normal operation of the unit.
Operation
• When the product is soaked (flooded or submerged) in water , contact an Authorized
Service Center for repair before using it again. There is risk of fire or eletric shock.
• Be sure to use only those parts which are listed in the svc parts list. Never attempt to
modify the equipment. The use of inappropriate parts can cause an electrical shock,
excessive heat generation or fire.
• Do not touch , operate, or repair the product with wet hands. Hold the plug by hand
when taking out. There is risk of electric shock or fire.
• Do not place a heater or other heating appliances near the power cable. There is risk of
fire and electric shock.
• Do not allow water to run into electric parts. Install the unit away from water sources.
There is risk of fire, failure of the product, or electric shock.
• Do not store or use or even allow flammable gas or combustibles near the product. There
is risk of fire.
• Do not use the product in a tightly closed space for a long time. Perform ventilation
regularly. Oxygen deficiency could occur and hence harm your health.
• Do not open the front grille of the product during operation. (Do not touch the
electrostatic filter, if the unit is so equipped.) There is risk of physical injury, electric
shock, or product failure.
• If strange sound, smell or smoke comes from product.Immediately turn the breaker off
or disconnect the power supply cable. There is risk of electric shock or fire.
• Ventilate the product room from time to time when operating it together with a stove, or
heating element etc. Oxygen deficiency can occur and hence harm your health.
• When the product is not to be used for a long time, disconnect the power supply plug or
turn off the breaker. There is risk of product damage or failure, or unintended operation.
• Take care to ensure that nobody especially kids could step on or fall onto the outdoor
unit. This could result in personal injury and product damage.
IMPORTANT SAFETY INSTRUCTIONS
5
ENGLISH
• Take care to ensure that power cable could not be pulled out or damaged during
operation. There is risk of fire or electric shock.
• Do not place ANYTHING on the power cable. There is risk of fire or electric shock.
• When flammable gas leaks, turn off the gas and open a window for ventilation befor
turning on the product. Do not use the telephone or turn switches on or off. There is risk
of explosion or fire.
• Make sure to ventilate sufficiently when this air conditioner and a heating appliance such
as a heater are used simultaneously. Failure to do so may result in fire, serious injury, or
product failure.
CAUTION
!
Installation
• Two or more people must lift and transport the product. Avoid personal injury.
• Do not install the product where it will be exposed to sea wind (salt spray) directly. It may
cause corrosion on the product.
• Install the drain hose to ensure that the condensed water is drained away properly. A
bad connection may cause water leakage.
• Keep level even when installing the product. To avoid vibration or noise.
• Do not install the product where the noise or hot air from the outdoor unit could damage
or disturb the neighborhoods. It may cause a problem for your neighbors and hence
dispute.
• Always check for gas (refrigerant) leakage after installation or repair of product. Low
refrigerant levels may cause failure of product.
Operation
• Do not use the product for special purposes, such as preserving foods, works of art, etc.
It is a consumer air conditioner, not a precision refrigeration system. There is risk of
damage or loss of property.
• Do not block the inlet or outlet of air flow. It may cause product failure.
• Use a soft cloth to clean. Do not use harsh detergents, solvents or splashing water etc.
There is risk of fire, electric shock, or damage to the plastic parts of the product.
• Do not touch the metal parts of the product when removing the air filter. There is risk of
personal injury.
• Do not step on or put anyting on the product. (outdoor units) There is risk of personal
injury and failure of product.
• Always insert the filter securely after cleaning. Clean the filter every two weeks or more
often if necessary. A dirty filter reduces the efficiency.
• Do not insert hands or other objects through the air inlet or outlet while the product is
operating. There are sharp and moving parts that could cause personal injury.
• Be cautious when unpacking and installing the product. Sharp edges could cause injury.
• If the refrigerant gas leaks during the repair, do not touch the leakaing refrigerant gas.
The refrigernat gas can cause frostbite (cold burn).
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
6
•
Do not tilt the unit when removing or uninstalling it. The condensed water inside can spill.
• Do not mix air or gas other than the specified refrigerant used in the system. If air enters
the refrigerant system, an excessively high pressure results, causing equipment damage
or injury.
• If the refrigerant gas leaks during the installation, ventilate the area immediately.
Otherwise it can be harmfull for your health.
• Dismantling the unit, treatment of the refrigerant oil and eventual parts should be done in
accordance with local and national standards.
• Replace the all batteries in the remote control with new ones of the same type. Do not
mix old and new batteries or different types of batteries. There is risk of fire or product
failure.
• Do not recharge or disassemble the batteries. Do not dispose off batteries in a fire. They
may burn or explode.
• If the liquid from the batteries gets onto your skin or clothes, wash it well with clean
water. Do not use the remote if the batteries have leaked. The chemicals in batteries
could cause burns or other health hazards.
• If you swallow the battery fluid from a leak, wash out the inside of your mouth thoroughly
and then consult a doctor. Failure to do so may result in serious health complications.
• Do not let the air conditioner run for a long time when the humidity is very high and a
door or a window is left open. Moisture may condense and wet or damage furniture.
• Do not expose your skin or kids or plants to the cool or hot air draft. This could harm to
your health.
• Do not drink the water drained from the product. It is not sanitary and could cause
serious health issues.
• Use a firm stool or ladder when cleaning, maintaining or repairing the product at an
height. Be careful and avoid personal injury.
According to IEC 660335-1
• This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge, unless they
have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety. Children should be supervised to ensure that they do not play
with the appliance.
According to EN 660335-1
• This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if
they have been given supervision or instruction concerning use of the appliance in a safe
way and understnd the hazards involved. Children shall not play with the appliance.
Cleaning and user maintenance shall not be made by children without supervision.
INSTALLATION PLACES
More than 200
B
C
B
A
More than 100
More than 2300
More than 100
(Unit : mm)
Unit : mm
Ceiling
Ceiling Board
Ceiling Board
H
1000
or more
500 or
more
500 or
more
300 or less
At least 1800
H or less
Floor
10 or
more
More than
200mm
More than 50mm
More than 50mm
More than
200mm
R
R
More than
200mm
More than
200mm
More than 700mm
More than 700mm
More than 300mm
INSTALLATION MANUAL
7
ENGLISH
- There should not be any heat source or
steam near the unit.
- There should not be any obstacles to prevent
the air circulation.
- A place where air circulation in the room will
be good.
- A place where drainage can be easily obtained.
- A place where noise prevention is taken into
consideration.
- Do not install the unit near the door way.
- Ensure the spaces indicated by arrows from
the wall, ceiling, or other obstacles.
- The indoor unit must keep the maintenance
space.
Type
Wall mounted 200100
ART COOL 200500
ART COOL Mirror
Console 300300
Floor Standing 300300
A B C
200100
250 or less
2,300
1,500
2,300
-
Ceiling installation
Floor / wall installation
Top view
Inspection hole 600 x 600
Air inlet vents
Control box
(unit: mm)
Chassis
TU/TT3,300
TQ/TR/TP3,600
TN/TM4,200
Side view
600
Air outlet vents
1000
600
Front
(unit: mm)
20 or more
H
• Suitable dimension "H" is necessary to get a
slope to drain as shown in the figure
INSTALLATION MANUAL
1(L) 2(N) 3
Connected to outdoor unit
or B.D. unit.
8
ENGLISH
ELECTRIC WIRING WORK
General instructions
- All field supplied parts and materials, electric
works must conform to local codes. Use
copper wire only.
- Follow the "WIRING DIAGRAM” attached to
the unit body to wire the outdoor unit, indoor
units and the remote controller.
- All wiring must be performed by an
authorized electrician
Wiring Connection
Connect the wires to the terminals on the
trol board individually according to the out
unit connection.
Ensure that the color of the wires of outdoor
unit and the terminal No. are the same as
those of indoor unit respectively
con-
door
CAUTION
!
• The connecting cable connected to the
indoor and outdoor unit should be complied with the following specifications
(Rubber insulation, type H05RN-F approved by HAR or SAA).
NORMAL
CROSS-SECTIONAL
GN/YL
• If the supply cord is damaged, it must
be replaced by a special cord or assembly available from the manufacturer of
its service agent.
AREA 0.75mm
20mm
2
Using the remote controller
You can operate the air conditioner more conveniently with the remote controller.
You will find the buttons for the additional
functions under the cover of the remote control.
OWNER'S MANUAL
9
ENGLISH
MAINTENANCE
Clean the product regularly to maintain
optimal performance and to prevent possible
breakdown.
CAUTION
!
• Turn off the power and unplug the
power cord before you perform any
maintenance; otherwise it may cause
electric shock.
• Never use water that is hotter than
40°C when you clean the filters. It may
cause deformation or discoloration.
• Never use volatile substances when
you clean the filters. They may damage
the surface of the product.
Operation Tips!
• Do not overcool the room.
This is not good for the health and wastes electricity.
•
Keep blinds or curtains closed.
Do not let direct sunshine enter the room
when the air conditioner is in operation.
• Keep the room temperature uniform.
Adjust the vertical and horizontal airflow direction to ensure a uniform temperature in
the room.
• Make sure that the doors and windows are
shut tight.
Avoid opening doors and windows as much
as possible to keep the cool air in the room.
• Clean the air filter regularly.
Blockages in the air filter reduce the airflow
and lower cooling and dehumidifying effects. Clean at least once every two weeks.
Ventilate the room occasionally.
•
Since windows are kept closed, it is a good
idea to open them and ventilate the room
now and then.
When the air conditioner is not
going....
When air conditioner is not going to be used
for a long time.
1 Operate the air conditioner at the following
settings for 2 to 3 hours.
• Type of operation: Fan operation
mode.(Refer to page "Fan Mode")
• This will dry out the internal mechanisms.
2 Turn off the breaker.
CAUTION
!
Turn off the breaker when the air conditioner is not going to be used for a long
time. Dirt may collect and may cause a
fire.
3 Remove the batteries from the Remote
Controller.
Helpful information
The air filters and your electiric bill.
If the air filters become clogged with dust, the
cooling capacity will drop, and 6% of the electricity used to operate the air conditioner will
be wasted.
When the air conditioner is to be
used again.
1 Clean the air filter and install it in the indoor
unit. (Refer to page "Maintenance and Service")
2 Check that the air inlet and outlet of the in-
door/outdoor unit are not blocked.
3 Check that the ground wire is connected
correctly. It may be connect to the indoor
unit side.
OWNER'S MANUAL
10
ENGLISH
Troubleshooting Tips! Save time and money!
Check the following points before requesting repairs or service.... If the malfunction persist,
please contact your dealer.
Case
The air conditioner does not
operate.
The room has a peculiar odor.
It seems that condensation is
leaking from the air conditioner.
Air conditioner does not operate for about 3 minutes when
restart.
Does not cool or heat effectively.
The air conditioner operation
is noisy.
Crack sound is heard.
Filter sign lamp (LED) is ON.
Remote control display is
faint, or no display at all.
The error code is occurred
after lightning struck
Explanation
• Have you made a mistake in timer operation?
• Has the fuse blown or has the circuit breaker been tripped?
• Check that this is not a damp smell exuded by the walls,
carpet, furniture or cloth items in the room.
• Condensation occurs when the airflow from the air conditioner cools the warm room air.
• This is the protector of the mechanism.
• Wait about three minutes and operation will begin.
• Is the air filter dirty? See air filter cleaning instructions.
• The room may have been very hot when the room air conditioner was first turned on. Allow time for it to cool down.
• Has the setting temperature been set incorrectly?
• Are the indoor unit's air inlet or outlet vents obstructed?
• For a noise that sounds like water flowing.
- This is the sound of freon flowing inside the air conditioner
unit.
• For a noise that sounds like the compressed air releasing
into atmosphere.
- This is the sound of the dehumidifying water being
processed inside the air conditioning unit.
• This sound is generated by the expansion/contraction of the
inlet grille, etc. due to changes of temperature.
• Cleaning the filter, press the Timer button and ◀ button of
wired remote controller at the same time for 3 sec.
• Has the circuit breaker been tripped?
• Are the batteries inserted in the opposite (+) and (-) directions?
• This product has been applied to the over current protection
circuit. Error can occur, but it is normal behavior. After few
minutes, It will operate normally.
Call the service immediately in the following situations
1 Anything abnormal such as burning smell, loud noise etc. happen. Stop the unit and turn the
breaker off. Never try to repair by yourself or restart the system in such cases.
2 Main power cord is too hot or damaged.
3 Error code is generated by self diagnosis.
4 Water leaks from indoor unit even if the humidity is low.
5 Any switch, breaker (safety, earth) or fuse fails to work properly
User must carry routine checkup & cleaning to avoid unit’s poor performance. In case of special
situation, the job must be carried out by service person only.
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.