Page 1
Technical Specification (TL19BNN)
1/10
Page 2
History
Ver. Date Contents
1.0 2017.12.26
Written
by
Checked
by
Approved
by
Note
2/10
Page 3
Contents
1. Product Introduction ...................................................................................................... 4
1.1 Block Diagram ...................................................................................................... 4
1.2 Environmental Specifications ............................................................................... 5
1.3 Electrical Specifications ....................................................................................... 5
1.3.1 Absolute Maximum and ESD Ratings ........................................................... 5
1.3.2 Current Consumption .................................................................................... 6
1.4 Mechanical Specifications .................................................................................. 6
1.4.1 Physical Dimensions and Connection Interface ............................................ 6
1.4.2 Mechanical Drawing ...................................................................................... 7
2. RF Specification ............................................................................................................ 8
2.1. LTE Specification ................................................................................................ 8
2.2. WCDMA Specification................………………………………………..…………… 9
3/10
Page 4
1. Product Introuction
The TL19BNN are designed for the automotive industry. They support LTE and WCDMA air
Interface standards. The TL19BNN are based on the Qualcomm MDM9628 wireless chipsets
and support the following bands.
Table 1. Supported Band
Region US
LTE
Band
WCDMA B2/B4/B5
1.1 Block Diagram
B2/B4/B5/B12/
B13/B17/B26
Confidential
Figure 1.1. TL19BNN Block diagram
4/10
Page 5
1.2 Environmental Specifications
The environmental specification for operating and storage of the TL19BNN are defined in the
the table below.
Table 2. Environmental Specifications
Parameter Temperature Range
Operating Temperature -40℃ to 85℃
Storage Temperature
Humidity 95% or less
-40℃ to +90℃
1.3 Electrical Specifications
This section provides details for some of the key electrical specifications of the TL19BNN
embedded modules.
1.3.1 Absolute Maximum Rating and ESD Ratings
This section defines the Absolute Maximum and Electrostatic Discharge (ESD) Ratings of the
TL19BNN embedded modules.
Warning: If these parameters are exceeded, even momentarily, damage may occur to the
device.
Table 3. Absolute Maximum Ratings
Parameter Min Max Units
+12.0_VPWR Power Supply Input - 16.0V V
VIN Voltage on any digital input or output pin - VREG_MDME+0.5 V
ESD Ratings
ESD1) Primary, Diversity antenna pads - Contact 10 kV
1) The ESD Simulator configured with 330pF, 2000Ω.
Caution: The TL19BNN embedded modules are sensitive to Electrostatic Discharge. ESD
countermeasures and handling methods must be used when handling the TL19BNN devices.
5/10
Page 6
1.3.2 Current Consumption
Table 4. TL19BNN Current Consumption (TBD)
Mode Parameter Typical Max Units
LTE
WCDMA
LTE Idle, Registered 3.6 4.0 mA
WCDMA Idle, Registered 3.6 4.0 mA
LTE Sleep Mode, Average Current 1.8 2.2 mA
WCDMA Sleep Mode, Average Current 1.8 2.2 mA
Max TX Output /Full RB 600 650
Max TX Output /Full RB 600 650
mA
mA
1.4 Mechanical Specifications
1.4.1 Physical Dimensions and Connection Interface
The TL19BNN embedded modules are a Land Grid Array (LGA) form factor device. The
device does not have a System or RF connectors. All electrical and mechanical connections
are made via the 387 pad TL19BNN on the underside of the PCB.
Table5. TL19BNN Embedded Module Dimensions
Parameter Nominal Max Units
Overall Dimension 34 x 40 34.35 x 40.35 mm
Overall Module Height 3.8 4.0 mm
PCB Thickness 1.0 1.1 mm
Flatness Specification 0.1 mm
Weight TBD g
6/10
Page 7
1.4.2 Mechanical Drawing
1.4.2.1 NAD PCB
34mm
[TOP View_Without shield Can cover] [TOP View_With shield Can cover]
3.8mm
40mm
[SIDE View_With shield Can cover]
7/10
Page 8
2. RF Specification
The specifications for the LTE and WCDMA interfaces are defined.
TL19BNN is designed to be compliant with the standard shown in the table below.
Table6. Standards Compliance
Technology Standards
LTE • 3GPP Release 8
WCDMA • 3GPP Release 9
2.1 LTE Specification
2.1.1 LTE RX Sensitivity
The Receiver Sensitivity of the TL19BNN are specified in the following table.
Table7. Conducted RX (Receive) Sensitivity – LTE Bands
BAND Method (DL CH) Specification
BAND 2
Reference
sensitivity
level(DUAL)
BAND 4
Reference
sensitivity
level(DUAL)
BAND 5
Reference
sensitivity
level(DUAL)
BAND 12
Reference
sensitivity
level(DUAL)
BAND 13
Reference
sensitivity
level(DUAL)
BAND 17
Reference
sensitivity
level(DUAL)
BAND 26
Reference
sensitivity
level(DUAL)
Measure BLER of Mid Channel (900) in Band2
Measure BLER of Mid Channel (2175) in Band4
Measure BLER of Mid Channel (2525) in Band5
Measure BLER of Mid Channel (5095) in Band12
Measure BLER of Mid Channel (5230) in Band13
Measure BLER of Mid Channel (5790) in Band17
Measure BLER of Mid Channel (8865) in Band26
2.2 WCDMA Specification
2.2.1 WCDMA RX Sensitivity
sensitivity : ≤-95
BLER : ≤ 5%
sensitivity : ≤-97
BLER : ≤ 5%
sensitivity : ≤-95
BLER : ≤ 5%
sensitivity : ≤-94
BLER : ≤ 5%
sensitivity : ≤-94
BLER : ≤ 5%
sensitivity : ≤-94
BLER : ≤ 5%
sensitivity : ≤-94.5
BLER : ≤ 5%
8/10
Page 9
The Receiver Sensitivity of the TL19BNN are specified in the following table.
Table8. Conducted RX (Receive) Sensitivity – WCDMA Bands
Item Method (DL CH) Specification
BAND2
BER(Bit Error
Rate)
BAND4
BER(Bit Error
Rate)
BAND5
BER(Bit Error
Rate)
Measure BER of Middle Channel (CH=9800)
in Band2 0.1% @≤-106.7dBm
Measure BER of Middle Channel (CH=1675)
in Band4.
Measure BER of Middle Channel (CH=4400)
in Band5 0.1% @≤-106.7dBm
0.1% @≤-106.7dBm
9/10
Page 10
Notice
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This device should be installed and operated with minimum distance 20cm
between the radiating element of this device and the user.
10/10
Loading...