LG SKSFD3613S Owner’s Manual

OWNER'S MANUAL

FRENCH DOOR

REFRIGERATOR

Read this owner's manual thoroughly before operating the appliance and keep it handy for reference at all times.

ENGLISH

SKSFD3613*

www.signaturekitchensuite.com (USA)

www.signaturekitchensuite.ca (CANADA)

MFL69497041

Copyright © 2020 Signature Kitchen Suite. All Rights Reserved.

Rev.01_092320

2

TABLE OF CONTENTS

3	IMPORTANT SAFETY		59 LIMITED WARRANTY
	INSTRUCTIONS	59		USA
3	READ ALL INSTRUCTIONS BEFORE USE	61		Canada
3	WARNING

6CAUTION

7PRODUCT OVERVIEW

7 Product Features

10 INSTALLATION

10Before Installing

11Choosing the Proper Location

13Removing/Assembling Handles

14Removing/Assembling Doors and Drawers

19Connecting the Water Line

22Leveling and Door Alignment

23Turning on the Power

24 OPERATION

24Before Use

25Control Panel

27Sabbath Mode

27Ice and Water Dispenser

29Ice Compartment

30Automatic Icemaker

31Storing Food

33Humidity Controlled Crispers

34Glide‘N’Serve

34Refrigerator Shelves

35Door-in-Door

37Door Bins

37Durabase

38 SMART FUNCTIONS

38 SIGNATURE KITCHEN SUITE Application

40Smart Diagnosis™ Feature

41Smart Grid Function

43 MAINTENANCE

43Cleaning

43Air Filter

44Water Filter

48 TROUBLESHOOTING

48FAQs

49Before Calling for Service

IMPORTANT SAFETY INSTRUCTIONS 3

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

Safety Messages

Your safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and follow all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or injure you and others. All safety messages will follow the safety alert symbol and either the word WARNING or CAUTION.

These words mean:

WARNING

You may be killed or seriously injured if you do not follow instructions.

CAUTION

You may be injured or cause damage to the product if you do not follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what may happen if the instructions are not followed.

WARNING

WARNING

•To reduce the risk of explosion, fire, death, electric shock, scalding or injury to persons when using this product, follow basic precautions, including the following:

Installation

•To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including the use of long-sleeved gloves and safety glasses.

•Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.

•Only connect this product to a dedicated grounded electrical outlet rated for use with this product (115 V, 60 Hz, AC only). It is the user’s responsibility to replace a standard 2-prong wall outlet with a standard 3-prong wall outlet.

•Do not use an outlet that can be turned off with a switch. Do not use an extension cord.

•The appliance must be positioned for easy access to a power source.

•When moving the refrigerator, be careful not to roll over or damage the power cord.

•Contact an authorized service center when installing or relocating the refrigerator.

•Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.

•Keep packing materials out of the reach of children. Packaging material can be dangerous for children. There is a risk of suffocation.

•Do not install the refrigerator in a damp or dusty place where insulation on electrical parts may deteriorate.

•Do not place the refrigerator in direct sunlight or expose it to the heat from heating appliances such as stoves or heaters.

<![if ! IE]>

<![endif]>ENGLISH

4 IMPORTANT SAFETY INSTRUCTIONS

• Do not bend or pinch the power cord excessively or place heavy objects on it.

Operation

•This appliance is intended to be used in household and similar applications such as:

-staff kitchen areas in shops, offices and other working environments;

-farm houses and by clients in hotels, motels and other residential type environments;

-bed and breakfast type environments;

-catering and similar non-retail applications.

•This product is not to be used for special purposes such as the storage of medicine or test materials or for use on ships, etc.

•DO NOT allow children to climb, stand, or hang on the refrigerator doors or on the shelves in the refrigerator. They could damage the refrigerator and seriously injure themselves.

•Do not allow children to climb into the refrigerator. They could be trapped and suffocated.

•Children should be supervised to ensure that they do not play with the refrigerator.

•Keep fingers out of pinch point areas; clearances between the doors and cabinets are necessarily small. Be careful closing doors when children are nearby.

•Do not touch frozen food or the metal parts in the freezer compartment with wet or damp hands. Doing so may cause frostbite.

•Do not refreeze frozen food that has thawed completely. Doing so may result in a serious health hazard.

•Do not use an adapter plug or plug the power plug into a multi-outlet extension cord.

•If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.

•Do not operate the refrigerator or touch the power cord with wet hands.

•Do not modify or extend the power cord.

•Do not use an uncertified power outlet. Do not plug appliance into a damaged wall outlet.

•Do not put hands, feet or other objects into the air vents or bottom of the refrigerator. Doing so could result in personal injury or electric shock.

•In the event of a gas leak (propane/LPG), ensure the area is adequately ventilated and contact an authorized service center before resuming use. Do not touch the refrigerator or power cord of the refrigerator.

•Disconnect the power cord immediately and contact an authorized service center if there is a strange noise, odor, or smoke coming from the appliance.

•Do not use any fuse (such as copper, steel wire, etc.) other than a standard fuse.

•Do not place or use an electrical appliance inside the refrigerator, unless it is of a type recommended by the manufacturer.

•Do not put animals inside the appliance.

•Do not place heavy or fragile objects, liquid filled containers, combustible substances, or flammable objects (such as candles and lamps) on the appliance.

•If connected to a circuit protected by fuses, use time delay fuse.

•Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of obstruction.

•Do not use mechanical devices or other means to accelerate the defrosting process, other than those recommended by the manufacturer.

•Do not use electrical appliances inside the food storage compartments of the appliance, unless they are of the type recommended by the manufacturer.

•Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

IMPORTANT SAFETY INSTRUCTIONS 5

Maintenance

	•	Do not use a hair dryer to dry the inside of the refrigerator.
	•	Do not light a candle to remove odors in the refrigerator.
			<![if ! IE]> <![endif]>ENGLISH
	•	In the event of a refrigerant leak, move flammable objects away from the refrigerator. Ensure the area is
		adequately ventilated and contact an authorized service center.
	•	Keep flammable materials and vapors, such as gasoline, away from the refrigerator.
	•	This appliance is not intended for use by persons (including children) with reduced physical, sensory or
		mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
		instruction concerning use of the appliance by a person responsible for their safety.
	•	Unplug the power plug before cleaning or repairing the refrigerator.
	•	The refrigerator and freezer compartment lights are interior LED lighting, and service should be
		performed by a qualified technician.
	• Unplug the power plug immediately in the event of a blackout or thunderstorm.
	•	Turn the power off if water or dust penetrates into the refrigerator. Call a service agent.
	• Do not store glass containers or soda in the freezer compartment. Contents may expand when frozen,
		break the container and cause injury.
	•	Do not store, disassemble or repair the appliance yourself or allow unqualified personnel to do so.

Disposal

•Junked or abandoned refrigerators are dangerous, even if they are sitting for only a few days. When disposing of the refrigerator, remove the packing materials from the door or take off the doors but leave the shelves in place so that children may not easily climb inside.

•If disposing of a refrigerator, make sure the refrigerant and insulation foam are removed for proper disposal by a qualified servicer. If you release the refrigerant or throw away the insulation foam, you may be fined or imprisoned in accordance with the relevant environmental law. Insulation foam contains flammable blowing gas.

•When discarding the appliance, remove the door gasket while leaving the shelves and bins in place, and keep children away from the appliance.

Grounding Instructions

•Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service personnel if you are in doubt whether the appliance is properly grounded. Do not modify the plug provided with the appliance; if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

•Have a certified electrician check the wall outlet and wiring for proper grounding.

•Never unplug the appliance by pulling on the power cord. Always grip the plug firmly and pull straight out from the outlet. Failure to do so may damage the power cord, resulting in a risk of fire and electric shock.

6 IMPORTANT SAFETY INSTRUCTIONS

Risk of Fire and Flammable Materials

This appliance contains a small amount of isobutane refrigerant (R600a), which is combustible. When transporting and installing the appliance, care should be taken to ensure that no parts of the refrigerating circuit are damaged. Refrigerant squirting out of the pipes could ignite or cause an eye injury. If a leak is detected, avoid any naked flames or potential sources of ignition and air out the room in which the appliance is standing for several minutes.

In order to avoid the creation of a flammable gas air mixture if a leak in the refrigerating circuit occurs, the size of the room in which the appliance may be sited depends on the amount of refrigerant used. The room must be 10.8 square feet (1 square meter) in size for every 8g of R600a refrigerant inside the appliance. The amount of refrigerant in your particular appliance is shown on the identification plate inside the appliance. Never start up an appliance showing any signs of damage. If in doubt, consult your dealer.

CAUTION

CAUTION

•To reduce the risk of minor or moderate injury to persons, malfunction, or damage to the product or property when using this product, follow basic precautions, including the following:

Installation

•Do not install the refrigerator where there may be a danger of the unit falling.

•The refrigerator must be properly installed in accordance with the Installation Instructions.

Operation

•Do not use aerosols near the refrigerator.

•This appliance is intended to be used only in domestic and similar applications.

•Do not strike or apply excessive force to any glass surface. Do not touch glass surfaces if they are cracked or broken.

•Do not overfill or pack items too tightly into door bins. Doing so may cause damage to the bin or personal injury if items are removed with excessive force.

•Do not hang on to or place heavy objects on the refrigerator’s dispenser.

Maintenance

•Do not use strong detergents like wax or thinners for cleaning. Clean with a soft cloth.

•Remove foreign objects (such as dust and water) off the prongs of the power plug and contact areas. Do not use a wet or damp cloth when cleaning the plug.

•Do not spray water directly on the inside or outside of the refrigerator.

•Do not clean glass shelves or covers with warm water when they are cold. They may break if exposed to sudden temperature changes.

SAVE THESE INSTRUCTIONS

PRODUCT OVERVIEW 7

PRODUCT OVERVIEW

Product Features

The images in this guide may be different from the actual components and accessories, which are subject to change by the manufacturer without prior notice for product improvement purposes.

Exterior

aFiltered Water and Ice Dispenser

Dispenses purified water and ice.

bLED Display

Displays the refrigerator and freezer temperature, the water filter condition and the dispenser status.

cControl Panel

Sets the refrigerator temperature and freezer temperature, the water filter condition and the dispenser mode.

dSmartPull™ Handle

Easily opens the freezer door.

eHandle

Opens and closes the refrigerator door.

fDoor Button

Opens the Door-in-Door Compartment.

gRefrigerator

Fresh food compartment

hFreezer

Frozen food compartment

<![if ! IE]>

<![endif]>ENGLISH

8 PRODUCT OVERVIEW

Interior

Door-in-Door: SKSFD3613*

aLED Interior Lighting

Lights up the inside of the refrigerator.

bIn-Door Icemaker (Refrigerator)

This is where ice is automatically produced and stored.

cDoor Mullion

Prevents the cold air in the refrigerator from escaping when the doors are closed.

CAUTION

•To reduce the risk of scratching the door or breaking the center door mullion, make sure that the folding door mullion is folded in before closing the left-hand door.

•The door alarm will sound every 30 seconds if the door remains open longer than one minute.

dHumidity Controlled Crisper

Helps vegetables and fruit to stay crisp and controls humidity.

eFixed Door Bin

Stores chilled food or drinks.

fAuto-Closing Hinge

The refrigerator doors and freezer drawers close automatically when pushed slightly. (The door only closes automatically when it is open at an angle of less than 30°.)

gDoor-in-Door Case

A convenient storage area for frequently-used items that require easy access.

PRODUCT OVERVIEW 9

h Cheese & Butter and Condiment Bins

Cheese & Butter and Condiment bins are specially designed for these items, making spreading butter and slicing cheese easier.

i Adjustable Refrigerator Shelf	<![if ! IE]> <![endif]>ENGLISH
The refrigerator shelves are adjustable to meet individual storage needs.
j Modular Door Bin
Interchangeable bins can be arranged to suit storage needs.
k Glide'N'Serve
Stores food items at a different temperature than the regular refrigerator area.
l Automatic Icemaker (Freezer)
Dispenses ice automatically.
m Ice Bin
Stores ice from the freezer icemaker.

NOTE

•The pad attached to the bottom of the ice bin is designed to reduce the sound of the ice dropping. Do not remove the pad.

nPullout Drawer

Provides extra storage within the freezer compartment.

oDurabase and Durabase Divider

Provides storage for large frozen food items.

Product Specifications

The appearance and specifications listed in this manual may vary due to constant product improvements.

Electrical requirements: 115 V, 60 Hz

Min. / Max. water pressure: 20 - 120 psi (138 - 827 kPa)

Model	Description	Net weight
SKSFD3613*	Counter-Depth, Door-in-Door French Door Refrigerator, Bottom	317 lb (144 kg)
	Freezer, Craft Ice

10 INSTALLATION

INSTALLATION

Before Installing

Installation Overview

Please read the following installation instructions first after purchasing this product or transporting it to another location.

aUnpacking the Refrigerator

bChoosing the Proper Location

cDisassembling/Assembling

dConnecting the Water Line

eLeveling and Door Alignment

WARNING

• Connect to potable water supply only.

							INSTALLATION 11
Unpacking the Refrigerator					install a booster pump to compensate for the
					low pressure.
	WARNING
• Use two or more people to move and install the
	refrigerator. Failure to do so can result in back				Electricity
	injury or other injury.				Use an individual, grounded outlet:115 Volts, 60
•	The refrigerator is heavy. Protect the floor when
					Hz, AC, 15 amps minimum.
	moving the refrigerator for cleaning or service.
	Always pull the refrigerator straight out when
					WARNING
	moving it. Do not wiggle or walk the refrigerator
	when trying to move it, as floor damage could				• Do not overload house wiring and cause a fire
	occur.				hazard by plugging in multiple appliances in the
•	Keep flammable materials and vapors, such as				same outlet with the refrigerator.
	gasoline, away from the refrigerator. Failure to				• To reduce the risk of electric shock, do not install
	do so can result in fire, explosion, or death.				the refrigerator in a wet or damp area.
NOTE					Flooring
• Remove tape and any temporary labels from
	your refrigerator before using. Do not remove				To avoid noise and vibration, the unit must be
	any warning labels, the model and serial number
					installed and leveled on a solidly constructed floor.
	label, or the Tech Sheet that is located under the
					If required, adjust the leveling legs to compensate
	front of the refrigerator.
					for the unevenness of the floor.
• To remove any remaining tape or glue, rub the
	area briskly with your thumb. Tape or glue				NOTE
	residue can also be easily removed by rubbing a

	small amount of liquid dish soap over the	• Installing on carpeting, soft tile surfaces, a
		platform or weakly supported structure is not
	adhesive with your fingers. Wipe with warm
		recommended.
	water and dry.

•Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove

	tape or glue. These products can damage the	Ambient Temperature
	surface of your refrigerator.	Install this appliance in an area where the
	• Reinstall or adjust shelves as needed.
		temperature is between 55 °F (13 °C) and 110 °F
	Refrigerator shelves are installed in the shipping
		(43 °C).
	position. Reinstall shelves according to your
		If the temperature around the appliance is too low
	individual storage needs.
		or high, cooling ability may be adversely affected.

Choosing the Proper

Location

Water

The refrigerator must be located where a water supply can be connected for the automatic icemaker.

NOTE

•The water pressure must be 20 - 120 psi or 138 -

827 kPa or 1.4 - 8.4 kgf/cm2. If the refrigerator is installed in an area with low water pressure (below 20 psi or 138 kPa or 1.4 kgf/cm2), you can

<![if ! IE]>

<![endif]>ENGLISH

12 INSTALLATION

Dimensions and Clearances

•Check the dimensions of the appliance and the installation path to ensure there is sufficient room to move the refrigerator through doors or narrow openings.

•If an opening is too narrow to fit the refrigerator through, remove the refrigerator doors. See Removing/ Assembling the Doors and Drawers in this manual.

•The installation location chosen for the refrigerator should allow space behind the unit for connections and airflow and space in front to open the doors and drawers.

•Too small of a distance from adjacent items may result in lowered freezing capability and increased electricity consumption charges. Allow at least 24 inches (610 mm) in front of the refrigerator to open the doors, and at least 2 inches (50.8 mm) between the back of the refrigerator and the wall.

	B
	E
	A
	F	G	H	I
C	D

-	Dimension/Clearance					SKSFD3613*
A	Depth without Handle			28		1/4″ (718 mm)
B	Width			35		3/4″ (908 mm)
C	Height to Top of Case			68		7/8″ (1750 mm)
D	Height to Top of Hinge			70		1/4″ (1785 mm)
E	Back Clearance			2″ (50 mm)
F	Depth without Door			24″ (610 mm)
G	Depth with Handle			30		3/4″ (781 mm)
H	Depth (Total with Freezer Drawer Open)			47		1/4″ (1200 mm)
I	Depth (Total with Door Open 90°)			42		5/8″ (1083 mm)

INSTALLATION 13

Removing/Assembling Handles

When moving the refrigerator through a narrow opening, removing the doors is preferred. If you must remove the handles, be very careful not to scratch the doors.

The appearance of the handles may vary from what is shown.

CAUTION

•When assembling or disassembling the refrigerator handles, grasp the handle firmly to avoid dropping it.

•Do not swing the handle into nearby people or animals.

•Make sure that the set screws are in place and the handle footprints at the ends of the handles are aligned correctly over the mounting fasteners on the doors. The set screws should be loose enough to allow the handle footprints to slide down into place over the mounting fasteners on the door.

•Make sure that there is not a gap between the door and handle after assembling the handle.

•Tools Needed

-3/32 in. Allen wrench

-1/8 in. Allen wrench

-1/4 in. Allen wrench

Removing Refrigerator Handles

1 Loosen the set screws a with a 3/32 in. Allen wrench and remove the handle.

2 If needed, loosen the mounting fasteners b that connect the refrigerator door and handle using a 1/4 in. Allen wrench, and remove the mounting fasteners.

Assembling Refrigerator Handles

1 If needed, reassemble the mounting fasteners a on the door with a 1/4 in. Allen wrench.

2 Place the handle on the door by fitting the handle footprints over the mounting fasteners and tightening the set screws b with a 3/32 in. Allen wrench.

Removing Freezer Drawer Handles

1 Loosen the set screws a located on the lower side of the handle with a 1/8 in. Allen wrench and remove the handle.

2 Loosen the mounting fasteners b with a 1/4 in. Allen wrench, and remove the mounting fasteners.

Assembling Freezer Drawer Handles

1 Assemble the mounting fasteners a at both ends of the handle with a 1/4 in. Allen wrench.

2 Place the handle on the door by fitting the handle footprints over the mounting

<![if ! IE]>

<![endif]>ENGLISH

14 INSTALLATION

fasteners and tightening the set screws b	Removing the Left Refrigerator
with a 1/8 in. Allen wrench.	Door
	1 The water supply is connected to the upper
	right part of the rear surface of the
	refrigerator. Remove the clip in the joint area.
	Hold the water supply connection and gently
	push the collet a to detach the water supply
	line as shown.

Removing/Assembling Doors and Drawers

If the entrance door is too narrow for the refrigerator to pass through, remove the refrigerator doors and move the refrigerator sideways through the doorway.

WARNING

•Use two or more people to remove and install the refrigerator doors and drawers.

•Disconnect the electrical supply to the refrigerator before installing.

•Do not put hands, feet or other objects into the air vents or bottom of the refrigerator.

•Be careful when handling the hinge and hinge lever.

•Remove food and bins before detaching the doors and drawers.

•Do not hold the handle when removing or replacing the doors and drawers as the handle may come off.

•Tools Needed

-3/32 in. Allen wrench

-1/8 in. Allen wrench

-1/4 in. Allen wrench

Removing the Hinge Cover

Remove the screws from the hinge cover at the top of the refrigerator. Lift the hook (not visible), located at the bottom of the front side of the cover with a flat-head screwdriver.

NOTE

• Disassembling/Assembling the Water Lines

b Collet c Tube d Insert line e Clip

2 Pull out the water supply lines f. Disconnect all the wire harnesses g . Unscrew the ground wire h.

3 Rotate the hinge lever i counterclockwise. Lift the top hinge j free of the hinge lever latch k.

CAUTION

•When lifting the hinge free of the latch, be careful that the door does not fall forward.

INSTALLATION 15

2 Rotate the hinge lever c clockwise. Lift the top hinge d free of the hinge lever latch e.

CAUTION

• When lifting the hinge free of the latch, be careful that the door does not fall forward.

4 Lift the door from the middle hinge pin and remove the door.

CAUTION

• Place the door, inside facing up, on a nonscratching surface.

3 Lift the door from the middle hinge pin and remove the door.

CAUTION

• Place the door, inside facing up, on a nonscratching surface.

<![if ! IE]>

<![endif]>ENGLISH

Removing the Right Refrigerator Door

1 Detach all the wire harnesses a. Unscrew the ground wire b.

NOTE

•The number of wire harnesses may vary depending on the model.

•Ground wire is only present on some models.

Removing Freezer Drawers

The Pullout Drawer located above the freezer drawer is not shown for clarity.

WARNING

•Use two or more people to remove and install the refrigerator doors and freezer drawer.

•Be careful of sharp hinges on both sides of the drawer.

•When you lay the drawer down, be careful not to damage the floor.

•Do not sit or stand on the freezer drawer.

16 INSTALLATION

WARNING

• To prevent accidents, keep children and pets away from the drawer. Do not leave the drawer

open. If the Durabase® storage bin is removed from the freezer drawer, there is sufficient space for a small child or pet to crawl inside.

1 Pull the drawer open to full extension.

2 Gently lift and pull out the ice bin.

CAUTION

• Do not hold the handle when removing or replacing the drawer. The handle may come off, causing personal injury.

6 Hold both rails and push them in simultaneously.

3 Lift the front of the drawer up, then pull it straight out.

4 Remove the Durabase basket from the rails. Remove the screws from the rails at both ends.

5 Grip both sides of the drawer and pull it up to remove it from the rails.

Assembling Freezer Drawers

1 Pull out both rails simultaneously, until they are fully extended.

2 Grasp the drawer on each side and hook the drawer supports into the rail tabs located on both sides.

INSTALLATION 17

CAUTION

•Do not hold the handle when removing or replacing the drawer. The handle may come off, causing personal injury.

3 Lower the door into its final position and insert the screws in the rails on both sides.

4 Insert the drawer into the frame, and push the drawer back until it clicks into place.

5 Replace the ice bin in the drawer. Insert the Durabase basket in the rail assembly.

<![if ! IE]>

<![endif]>ENGLISH

Assembling the Right Refrigerator

Door

CAUTION

• Install the right-side door first.

1 Make sure that the plastic sleeve is inserted in the bottom of the door. Lower the door onto the middle hinge pin as shown in the figure.

2 Fit the hinge a over the hinge lever latch b and slot it into place. Rotate the lever c counterclockwise to secure the hinge.

3 Connect all the wire harnesses d. Screw in the ground wire e.

18 INSTALLATION

NOTE		4 Push the water supply lines into the hole on
		the top case and pull them through the
•	The number of wire harnesses may vary	backplate.
	depending on the model.
•	Ground wire is only present on some models.

Assembling the Left Refrigerator

Door

CAUTION

•Install the left refrigerator door after the right door is installed.

1 Make sure that the plastic sleeve is inserted in the bottom of the door. Install the refrigerator door onto the middle hinge.

2 Fit the hinge a over the hinge lever latch b and slot it into place. Rotate the lever c clockwise and fasten the hinge.

5 Hold the water supply connection and gently push in the collet d to connect the water supply lines as shown. Insert the tube at least 5/8 inch (15 mm) into the connector. Insert the clip on the joint to fasten the tubes in place.

NOTE

•Disassembling/Assembling the Water Lines

e Collet f Tube g Insert line h Clip

•Gently press the collet and insert the tube until only one line shows on the tube.

3 Connect all the wire harnesses and the ground wire.

INSTALLATION 19

Assembling the Hinge Cover

Position the hinge cover in its place. Insert and tighten the cover screws.

Connecting the Water Line

Before Beginning

This water line installation is not covered by the refrigerator warranty. Follow these instructions carefully to minimize the risk of expensive water damage.

If necessary, call a qualified plumber to correct water hammer before installing the water supply line to the refrigerator. Water banging in the pipes (water hammer) in residential plumbing can cause damage to refrigerator parts and lead to water leakage or flooding.

•Turn the icemaker OFF if the refrigerator will be used before the water line is connected.

•Do not install the icemaker tubing in areas where the ambient temperatures fall below freezing.

WARNING

• Connect to potable water supply only.

CAUTION

•To prevent burns and product damage, only connect the refrigerator water line to a cold water supply.

•Wear eye protection during installation to prevent injury.

•Where reverse osmosis water filtration system is connected to a cold water supply:

-40 - 60 psi minimum to reverse osmosis system (2.8 kgf/cm2 - 4.2 kgf/cm2, or less than 2 - 3 seconds to fill a cup of 7 oz capacity)

If the water pressure from the reverse osmosis

system is less than 20 psi or 138 kPa or 1.4 kgf/cm2 (takes more than 4 seconds to fill a cup of 7 oz or 198 cc capacity):

•Check to see if the sediment filter in the reverse osmosis system is blocked. Replace the filter if necessary.

•Allow the storage tank on the reverse osmosis system to refill after heavy usage.

•If the water pressure remains low, call a licensed, qualified plumber.

•All installations must be in accordance with local plumbing code requirements.

Supplies Needed

•Copper or PEX Tubing, ¼ in. outer diameter, to connect the refrigerator to the water supply. Be sure both ends of the tubing are cut square. To determine how much tubing you need, measure the distance from the water valve on the back of the refrigerator to the water supply pipe. Then, add 8 feet (2.4 m). Be sure there is sufficient extra tubing (about 8 feet [2.4 m] coiled into 3 turns of about 10 in. [25 cm] diameter) to allow the refrigerator to move out from the wall after installation.

•Power drill.

•½ in. or adjustable wrench.

•Flat-blade and Phillips screwdrivers.

•Two ¼ in. outer diameter compression nuts and 2 ferrules (sleeves) to connect the copper tubing to the shutoff valve and the refrigerator water valve.

Water Pressure

You will need a cold water supply.

Water Pressure

•Models with water filter:

- 20 - 120 psi (138 - 827 kPa)

•If your existing copper water line has a flared fitting at the end, purchase an adapter (available at plumbing supply stores) to connect the water line to the refrigerator OR cut off the flared

<![if ! IE]>

<![endif]>ENGLISH

20 INSTALLATION

fitting with a tube cutter and use a compression fitting.

•Shutoff valve to connect to the cold water line. The shutoff valve should have a water inlet with a minimum inside diameter of 5/32 in. at the point of connection to the COLD WATER LINE. Saddle-type shutoff valves are included in many water supply kits. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.

NOTE

•A self-piercing saddle type water valve should not be used.

Water Line Installation Instructions

Install the shutoff valve on the nearest frequently used drinking water line.

WARNING

•When using any electrical device (such as a power drill) during installation, be sure the device is battery-powered, double-insulated or grounded in a manner that will prevent the hazard of electric shock.

1 Shut off the main water supply.

•Turn on the nearest faucet to relieve the pressure on the line.

2 Choose the valve location.

•Choose a location for the valve that is easily accessible. It is best to connect into the side of a vertical water pipe. When it is necessary to connect into a horizontal water pipe, make the connection to the top or side, rather than at the bottom, to avoid drawing off any sediment from the water pipe.

3 Drill the hole for the valve.

•Drill a ¼ in. hole in the water pipe using a sharp bit. Remove any burrs resulting from drilling the hole in the pipe. Be careful not to allow water to drain into the drill. Failure to drill a ¼ in. hole may result in reduced ice production or smaller cubes.

NOTE

•The hookup line cannot be white, plastic tubing. Licensed plumbers must use only copper tubing (NDA tubing #49595 or #49599) or Cross Link Polyethylene (PEX) tubing.

4 Fasten the shutoff valve.

•Fasten the shutoff valve to the cold water pipe with the pipe clamp.

NOTE

•Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.

aPipe Clamp

bSaddle-Type Shutoff Valve

cVertical Cold Water Pipe