LG Electronics BH6730S, S63T1-W, S63S2-S, S63S2-C User Manual

OWNER’S MANUAL
SMART 3D Blu-ray™ HOME THEATER SYSTEM
Please read this manual carefully before operating your set and retain it for future reference.
BH6730S (BH6730S, S63S2-S/ C, S63T1-W)
www.lg.com

Safety Information

1

Getting Started

CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
enclosure that may be of sucient magnitude to constitute a risk of electric shock to persons.
instructions in the literature accompanying the product.
WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands
after handling.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
WARNING: Do not install this equipment in a conned space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings shall be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product shall not be placed in a built­in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instruction has been adhered to.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO QUALIFIED SERVICE PERSONNEL.
This lightning ash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing)
CAUTION : CLASS 1M VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. DO NOT VIEW DIRECTLY WITH OPTICAL INSTRUMENTS Use of controls, adjustments or the performance of procedures other than those specied herein may result in hazardous radiation exposure.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit;
That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specication page of this owner’s manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or re. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized service center. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance. To disconnect power from the mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible.
This device is equipped with a portable battery or accumulator.
Safety way to remove the battery or the battery from the equipment: Remove the
old battery or battery pack, follow the steps in reverse order than the assembly. To prevent contamination of the environment and bring on possible threat to human and animal health, the old battery or the battery put it in the appropriate container at designated collection points. Do not dispose of batteries or battery together with other waste. It is recommended that you use local, free reimbursement systems batteries and accumulators. The battery should not be exposed to excessive heat such as sunshine, re or the like.
Getting Started 3
CAUTION: The apparatus shall not be exposed to water (dripping or splashing) and no objects lled with liquids, such as vases, shall be placed on the apparatus.
FCC Compliance Statement
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
yReorient or relocate the receiving antenna.
yIncrease the separation between the equipment
and receiver.
yConnect the equipment into an outlet on a
circuit dierent from that to
ywhich the receiver is connected.
yConsult the dealer or an experienced radio/TV
technician for help.
CAUTION: Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment
FCC RF Radiation Exposure Statement : This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. End users must follow the specic operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
FCC Radio Frequency Interference Requirements
This device is restricted to indoor use due to its operation in the 5.15 to 5.25 GHz frequency range. FCC requires this product to be used indoors for the frequency range 5.15 to 5.25 GHz to reduce the potential for harmful interference to co-channel Mobile Satellite systems. High power radars are allocated as primary users of the 5.25 to 5.35 GHz and 5.65 to 5.85 GHz bands. These radar stations can cause interference with and/or damage this device. This device cannot be co-located with any other transmitter.
CAUTION: Regulations of the FCC and FAA prohibit airborne operation of radio-frequency wireless devices because their signals could interfere with critical aircraft instruments.
Responsible Party : LG Electronics USA, Inc. 1000 Sylvan Avenue Englewood Clis, NJ 07632
TEL. : +1-800-243-0000
1
Getting Started
Getting Started4
Notes on copyrights
yBecause AACS (Advanced Access Content
System) is approved as content protection
1
Getting Started
system for Blu-ray Disc format, similar to use of CSS (Content Scramble System) for DVD format, certain restrictions are imposed on playback, analog signal output, etc., of AACS protected content. The operation of this product and restrictions on this product may vary depending on your time of purchase as those restrictions may be adopted and/or changed by AACS after the production of this product.
yFurthermore, BD-ROM Mark and BD+ are
additionally used as content protection systems for Blu-ray Disc format, which imposes certain restrictions including playback restrictions for BD-ROM Mark and/or BD+ protected content. To obtain additional information on AACS, BD-ROM Mark, BD+, or this product, please contact an authorized Customer Service Center.
yMany BD-ROM/DVD discs are encoded with
copy protection. Because of this, you should only connect your player directly to your TV, not to a VCR. Connecting to a VCR results in a distorted picture from copy-protected discs.
yThis product incorporates copyright protection
technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Rovi Corporation, and is intended for home and other limited viewing uses only unless otherwise authorized by Rovi Corporation. Reverse engineering or disassembly is prohibited.
yUnder the U.S. Copyright laws and Copyright
laws of other countries, unauthorized recording, use, display, distribution, or revision of television programs, videotapes, BD-ROM discs, DVDs, CDs and other materials may subject you to civil and/ or criminal liability.
Caution
>
yWatching a 3D content for a long period
time may cause dizziness or tiredness.
yIt is not recommended to watch a movie
in 3D mode for inrm, child and pregnant woman.
yIf you are experiencing headache, tiredness
or dizziness while viewing content in 3D, it is strongly recommended to stop the playback and rest until you feel normal.
Getting Started 5
IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power­supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
1
Getting Started
Table of Contents6
Table of Contents
1 Getting Started
2 Safety Information 8 Introduction 8 – Playable discs and symbols used in
this manual
9 – About the “7” symbol display 9 – Regional code 10 Remote Control 11 Front Panel 11 Rear Panel
2 Connecting
12 Positioning the System 13 Speaker Connection 13 – Attaching the speakers to the player 14 Connecting to Your TV 15 – What is SIMPLINK? 15 – ARC (Audio Return Channel) function 16 – Resolution setting 17 Antenna Connection 17 Connections with External Device 17 – AUX connection 18 – PORT. IN connection 18 – OPTICAL IN connection 19 Connecting to Your Home Network 19 – Wired network connection 19 – Wired network setup 21 – Wireless network connection 21 – Wireless network setup
3 System Setting
24 Initial Setup 25 Settings 25 – Adjust the setup settings 26 – [NETWORK] menu 27 – [DISPLAY] menu 28 – [LANGUAGE] menu 29 – [AUDIO] menu 31 – [LOCK] menu 32 – [OTHERS] menu
33 Sound Effect
4 Operating
34 Home Menu Display 34 – Using [HOME] menu 34 – Using the Smart Share 35 Playing the Linked Devices 35 – Playing a disc 35 – Playing Blu-ray 3D disc 36 – Playing a file on disc/USB device 37 – Playing a file on a network server 38 Using Home Network Server for PC 38 – Installing Nero MediaHome 4
Essentials 38 – Sharing files and folders 39 – About Nero MediaHome 4 Essentials 39 – System requirements 40 General Playback 40 – Basic operations for video and audio
content 40 – Basic operations for photo content 40 – Using the disc menu 41 – Resume playback 41 – Last scene memory 42 On-Screen Display 42 – To control video playback 42 – Displaying content information on-
screen 44 Advanced Playback 44 – Repeat playback 44 – Repeating a specific portion 44 – Playing from selected time 45 – Selecting a subtitle language 45 – Hearing a different audio 45 – Watching from a different angle 45 – Changing the TV Aspect Ratio 46 – Changing Subtitle Code Page 46 – Changing the Picture Mode 46 – Viewing content information 47 – Changing content list view 47 – Selecting a subtitle file 48 – Listening to music during slide show 48 – Setting the [3D] option 49 Advanced Features 49 – Wi-Fi Direct™ 50 – Enjoying BD-Live™
Table of Contents 7
50 – LG AV Remote 50 – Private Sound Mode 51 – Viewing information from Gracenote
Media Database 52 – Audio CD recording 52 – Recording from FM radio or AUX/
PORTABLE source 53 Radio Operations 53 – Listening to the radio 53 – Presetting the radio stations 53 – Deleting a saved station 53 – Deleting all the saved stations 53 – Improving poor FM reception 54 Playing the iPod 54 – Enjoying iPod on the screen 54 – Enjoying the iPod IN mode 56 Using Bluetooth technology 56 – Listening to music stored on the
Bluetooth devices 58 Using the Premium 58 Using the LG Smart World 59 – Signing in 59 – Searching online content 60 Using the My Apps Menu
5 Troubleshooting
61 Troubleshooting 61 – General 62 – Network 63 – Picture 63 – Sound 63 – Customer Support 63 – Open Source Software Notice
65 Network Software Update 65 – Network update notification 65 – Software update 67 Additional Information 67 – File requirement 68 – AVCHD (Advanced Video Codec High
Definition) 69 – About DLNA 69 – Certain system requirements 69 – Compatibility notes 70 Audio Output Specifications 71 Area Code List 72 Language Code List 73 Trademarks and Licenses 76 Specifications 78 Maintenance 78 – Handling the unit 78 – Notes on discs 79 Important Information relating to Network
Services
1
2
3
4
5
6
6 Appendix
64 Controlling a TV with the Supplied
Remote Control
64 – Setting up the remote to control your
TV
Some of the content in this manual may dier from your player depending on the software of the player or your service provider.
Getting Started8

Introduction

1

Playable discs and symbols used in this manual

Getting Started
Media/Term Logo Symbol Description
yDiscs such as movies that can be purchased or
rented.
y“Blu-ray 3D” discs and “Blu-ray 3D ONLY” discs.
yBD-R/RE discs that are recorded in BDAV format.
yBD-R/RE discs that contain Video, Audio or
Photo les.
yISO 9660+JOLIET, UDF and UDF Bridge format
yDiscs such as movies that can be purchased or
rented.
yVideo mode and nalized only
ySupports the dual layer disc also
Finalized AVCHD format
yDVD±R/RW discs that contain Video, Audio or
Photo les.
yISO 9660+JOLIET, UDF and UDF Bridge format
Blu-ray
DVD-ROM
DVD-R
DVD-RW
DVD+R
DVD+RW
(8 cm, 12 cm)
e
y u i
r
o
y u i
DVD-RW (VR)
(8 cm, 12 cm)
Audio CD
(8 cm, 12 cm)
CD-R/RW
(8 cm, 12 cm)
Note
Caution
r
t
y u i
,
>
VR mode and nalized only
Audio CD
yCD-R/RW discs that contain Video, Audio or
Photo les.
yISO 9660+JOLIET, UDF and UDF Bridge format
Indicates special notes and operating features.
Indicates cautions for preventing possible damages from abuse.
Note
,
yDepending on the conditions of the
recording equipment or the CD-R/RW (or DVD±R/RW) disc itself, some CD-R/RW (or DVD±R/RW) discs cannot be played on the unit.
yDepending on the recording software & the
nalization, some recorded discs (CD-R/RW, DVD±R/RW, BD-R/RE) may not be playable.
yBD-R/RE, DVD±R/RW and CD-R/RW discs
recorded using a personal computer or a DVD or CD Recorder may not play if the disc is damaged or dirty, or if there is dirt or condensation on the player’s lens.
yIf you record a disc using a personal
computer, even if it is recorded in a compatible format, there are cases in which it may not play because of the settings of the application software used to create the disc. (Check with the software publisher for more detailed information.)
yThis player requires discs and recordings to
meet certain technical standards in order to achieve optimal playback quality.
yPre-recorded DVDs are automatically set to
these standards. There are many dierent types of recordable disc formats (including CD-R containing MP3 or WMA les) and these require certain pre-existing conditions to ensure compatible playback.
yCustomers should note that permission
is required in order to download MP3 / WMA les and audio from the Internet. Our company has no right to grant such permission. Permission should always be sought from the copyright owner.
yYou have to set the disc format option
to [Mastered] in order to make the discs compatible with the LG players when formatting rewritable discs. When setting the option to Live System, you cannot use it on LG player. (Mastered/Live File System : Disc format system for windows Vista)
Getting Started 9

About the “7” symbol display

“7” may appear on your TV display during operation and indicates that the function explained in this owner’s manual is not available on that specic media.

Regional code

This unit has a regional code printed on the rear of the unit. This unit can play only BD-ROM or DVD discs labeled same as the rear of the unit or “ALL”.
1
Getting Started
Getting Started10
INFO/MENU
FUNCTION

Remote Control

1
Getting Started
FUNCTION
INFO/MENU
Battery Installation
Remove the battery cover on the rear of the Remote Control, and insert R03 (size AAA) battery with
and 5 matched correctly.
4
• • • • • • a • • • • • •
FUNCTION: Changes input mode.
SUBTITLE: Selects a subtitle
language.
(POWER): Switches the player
1
ON or OFF.
(OPEN/CLOSE): Ejects a disc.
B
SLEEP: Sets a certain period of time after which the unit will switch to o.
INFO/MENU (m): Displays or exits On-Screen Display.
HOME ( ): Displays or exits the [Home Menu].
DISC MENU: Accesses menu on a disc.
• • • • • • b • • • • •
Direction buttons: Selects an option in the menu.
PRESET +/-: Selects programme of Radio.
TUNING +/-: Tunes in the desired radio station.
ENTER (b): Acknowledges menu selection.
BACK ( ): Exits the menu or returns to the previous screen.
TITLE/POPUP: Displays the DVD title menu or BD-ROM’s pop-up menu, if available.
(STOP): Stops playback.
Z
(PLAY): Starts playback.
z
(PAUSE/STEP): Pauses
M
playback.
C/V
(SKIP): Goes to the next or previous chapter / track / le.
c/v
(SCAN): Searches
backward or forward.
• • • • • • c • • • • •
SPEAKER LEVEL: Sets the sound level of desired speaker.
SOUND EFFECT: Selects a sound eect mode.
VOL +/-: Adjusts speaker volume.
OPTICAL/ TV SOUND : Changes
input mode to optical directly.
MUTE: Mute the unit.
Colored (R, G, Y, B) buttons:
- Use to navigate BD-ROM menus. They are also used as shortcut buttons for specic menus.
- B button: Selects mono/ stereo in FM mode.
0-9 numerical buttons: Selects numbered options in a menu.
CLEAR: Removes a mark on the search menu or a number when setting the password.
REPEAT (h): Repeats a desired section or sequence.
MUSIC ID: When connected to the network, can provide information about the current song while movie playback.
AUDIO: Selects an audio language or audio channel.
(REC): Records from an Audio
X
CD, FM radio or AUX source to USB.
: Marked button is not available.
?
• • • • • • d • • • • •
TV Control Buttons: See page
64.

Front Panel

Getting Started 11
abc
de
Disc Tray
a
Display Window
b
Operation buttons
c
(Open / Close)
R
(Play / Pause)
T
(Stop)
I
F (Function)
Changes the input source or function.
VOL -/+
(Power)
1/!

Rear Panel

abcdefgh
PORT. IN
d
USB (iPod/iPhone/iPad) Port
e
1
Getting Started
AC power cord
a
Speakers connectors
b
Cooling Fan
c
AUX (L/R) INPUT
d
OPTICAL IN
e
Antenna Connector
f
LAN port
g
HDMI OUT TO TV
h
Connecting12
B
DEE
F
A
A
G
C
ABA
A
B
D
E
F
A
A
A
A
A
G
C
DEE
F
A
G
C
B
A
DEE
F
A
G
C
B
DEE
F
A
G
C
DEE
F
A
G
E
EFG
E
F
G
G

Positioning the System

The following illustration shows an example of positioning the system. Note that the illustrations in these instructions dier from the actual unit for explanation purposes. For the best possible surround sound, all the speakers other than the subwoofer should be placed at the same distance from the listening
2
position (

Connecting

).
Caution
>
yBe careful to make sure children not to put
their hands or any objects into the *speaker duct. *Speaker duct: A hole for plentiful bass sound on speaker cabinet (enclosure).
yPlace the center speaker at a safe distance
from the child’s reach. Otherwise it may result in the speaker falling down and causing personal injury and/or property damage.
yThe speakers contain magnetic parts, so
colour irregularity may occur on the CRT TV screen or PC monitor screen. Please use the speakers away from the TV screen or PC monitor screen.
yBefore using the subwoofer, remove the
protective vinyl.
Front left speaker (L)/ Front right speaker (R):
Place the front speakers to the sides of the monitor or screen and as ush with the screen surface as possible.
Center speaker:
Place the center speaker above or below the monitor or screen.
Surround left speaker (L)/ Surround right speaker (R):
Place these speakers behind your listening position, facing slightly inwards.
Subwoofer:
The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front speakers. Turn it slightly toward the center of the room to reduce the wall reections.
Unit
Connecting 13

Speaker Connection

Attaching the speakers to the player

1. Connect the wires to the unit. Match each wire’s colored band to the same colored connection terminal on the rear of the unit. To connect the cable to the unit, press each plastic finger pad to open the connection terminal. Insert the wire and release the finger pad.
Connect the black stripe of each wire to the terminals marked -(minus) and the other end to the terminals marked + (plus).
Connect a woofer cord to the player. When connecting a woofer cord to the player, insert the connector until it clicks.
To connect the cable to the speakers, press each plastic nger pad to open the connection terminals on the base of each speaker. Insert the wire and release the nger pad.
Caution
>
yBe careful to make sure children do not put
their hands or any objects into the *speaker duct. *Speaker duct : A hole for plentiful bass sound on speaker cabinet (enclosure).
yThe speakers contain magnet parts, so color
irregularity may occur on the TV screen or PC monitor screen. Please use the speakers far away from either TV screen or PC monitor.
2
Connecting
2. Connect the wires to the speakers. Connect the other end of each wire to the correct speaker according to the color coding:
Color Speaker Position
Grey Rear Rear right
Blue Rear Rear left
Green Center Center
Orange
Red Front Front right
White Front Front left
Sub woofer
Any front position
Connecting14

Connecting to Your TV

If you have a HDMI TV or monitor, you can connect it to this player using a HDMI cable (Type A, High speed HDMI™ cable with Ethernet). Connect the HDMI jack on the player to the HDMI jack on a HDMI compatible TV or monitor.
2
Connecting
Rear of the unit
HDMI cable not included
TV
Note
,
yIf a connected HDMI device does not accept
the audio output of the player, the HDMI device’s audio sound may be distorted or may not output.
yWhen you use HDMI connection, you can
change the resolution for the HDMI output. (Refer to “Resolution setting” on page 16 )
ySelect the type of video output from the
HDMI OUT jack using [HDMI Color Setting] option on the [Settings] menu (see page
28).
yChanging the resolution when the
connection has already been established may result in malfunctions. To solve the problem, turn o the player and then turn it on again.
yWhen the HDMI connection with HDCP
is not veried, TV screen is changed to black screen. In this case, check the HDMI connection, or disconnect the HDMI cable.
yIf there are noises or lines on the screen,
please check the HDMI cable (length is generally limited to 4.5 m(15 ft.)).
Set the TV’s source to HDMI (refer to TV’s Owner’s manual).
Additional Information for HDMI
yWhen you connect a HDMI or DVI compatible
device make sure of the following:
-Try switching o the HDMI/DVI device and this player. Next, switch on the HDMI/DVI device and leave it for around 30 seconds, then switch on this player.
-The connected device’s video input is set correctly for this unit.
-The connected device is compatible with 720x480p, 1280x720p, 1920x1080i or 1920x1080p video input.
yNot all HDCP-compatible HDMI or DVI devices
will work with this player.
-The picture will not be displayed properly with non-HDCP device.
Connecting 15

What is SIMPLINK?

Some functions of this unit are controlled by the TV’s remote control when this unit and LG TV’s with SIMPLINK are connected through HDMI connection.
Controllable functions by LG TV’s remote control; Play, Pause, Scan, Skip, Stop, Power O, etc.
Refer to the TV owner’s manual for the details of SIMPLINK function.
LG TV’s with SIMPLINK function has the logo as shown above.
Note
,
Depending on the disc type or playing status, some SIMPLINK operation may dier from your purpose or not work.

ARC (Audio Return Channel) function

The ARC function enables an HDMI capable TV to send the audio stream to HDMI OUT of this player.
To use this function:
-Your T V must support the HDMI-CEC and ARC function and the HDMI-CEC and ARC must be set to On.
-The setting method of HDMI-CEC and ARC may dier depending on the TV. For details about ARC function, refer to your TV manual.
-You must use the HDMI cable (Type A, High Speed HDMI™ cable with Ethernet).
-You must connect with the HDMI IN that supports the ARC function using the HDMI OUT on this player.
-You can connect only one Home Theater to TV compatible with ARC.
Note
,
To activate [SIMPLINK / ARC] function, set this option to [On]. (page 32)
2
Connecting
Connecting16

Resolution setting

The player provides several output resolutions for HDMI OUT jack. You can change the resolution using [Settings] menu.
1. Press HOME ( ).
2. Use
3. Use
2
Connecting
4. Use
5. Use
ENTER (b). The [Settings] menu appears.
press D to move to the second level.
then press ENTER (b) to move to the third level.
press ENTER (b) to confirm your selection.
to select the [Settings] and press
A/D
to select [DISPLAY] option then
W/S
to select the [Resolution] option
W/S
to select the desired resolution then
W/S
Note
,
yIf your TV does not accept the resolution
you have set on the player, you can set resolution to 480p as follows:
1. Press B to open the disc tray.
2 Press Z (STOP) for more than 5 seconds.
yIf you select a resolution manually and then
connect the HDMI jack to TV and your TV does not accept it, the resolution setting is set to [Auto].
yIf you select a resolution that your TV
does not accept, the warning message will appear. After resolution change, if you cannot see the screen, please wait 20 seconds and the resolution will automatically revert back to the previous resolution.
yThe 1080p video output frame rate may
be automatically set to either 24 Hz or 60 Hz depending both on the capability and preference of the connected TV and based on the native video frame rate of the content on the BD-ROM disc.
Connecting 17

Antenna Connection

Connect the supplied antenna for listening to the radio.
Rear of the unit
Note
,
Be sure to fully extend the FM wire antenna.

Connections with External Device

AUX connection

You can enjoy the sound from an external component through the speakers of this system.
Connect the analog audio output jacks of your component into the AUX L/R (INPUT) on this unit. And then select the [AUX] option by pressing FUNCTION.
You can also use the F (Function) button on the front panel to select the input mode.
Rear of the unit
Red White
2
Connecting
To the audio output jacks
of your component
(T V, VCR, etc.)
Connecting18

PORT. IN connection

You can enjoy the sound from your portable audio player through the speakers of this system.
Connect the headphones (or line out ) jack of the portable audio player into the PORT. IN socket of this unit. And then select the [PORTABLE] option by pressing FUNCTION.
You can also use the F (Function) button on the front panel to select the input mode.
2
Connecting
MP3 player, etc...

OPTICAL IN connection

You can enjoy the sound from your component with a digital optical connection through the speakers of this system.
Connect the optical output jack of your component into the OPTICAL IN jack on the unit. And then select the [OPTICAL] option by pressing FUNCTION. Or press OPTICAL / TV SOUND to select directly.
You can also use the F (Function) button on the front panel to select the input mode.
Rear of the unit
To the digital optical output jack of your component
Optical cable not included

Connecting to Your Home Network

This player can be connected to a local area network (LAN) via the LAN port on the rear panel or the internal wireless module. By connecting the unit to a broadband home network, you have access to services such as software updates, BD-Live interactivity and online content services.

Wired network connection

Using a wired network provides the best performance, because the attached devices connect directly to the network and are not subject to radio frequency interference.
Please refer to the documentation for your network device for further instructions.
Connect the player’s LAN port to the corresponding port on your Modem or Router using a commercially available LAN or Ethernet cable.
Note
,
yWhen plugging or unplugging the LAN
cable, hold the plug portion of the cable. When unplugging, do not pull on the LAN cable but unplug while pressing down on the lock.
yDo not connect a modular phone cable to
the LAN port.
ySince there are various connection
congurations, please follow the specications of your telecommunication carrier or internet service provider.
yIf you want to access content from DLNA
servers, this player must be connected to the same local area network with them via a router.
yTo set your PC as a DLNA server, install the
supplied Nero MediaHome 4 on your PC. (page 38)
Connecting 19
Broadband service
Router
DLNA certied servers
Rear of the unit

Wired network setup

If there is a DHCP server on the local area network (LAN) via wired connection, this player will automatically be allocated an IP address. After making the physical connection, a small number of home networks may require the player’s network setting to be adjusted. Adjust the [NETWORK] setting as follow.
Preparation
Before setting the wired network, you need to connect the broadband internet to your home network.
2
Connecting
Connecting20
1. Select [Connection Setting] option in the [Settings] menu then press ENTER (b).
2
2. Read the preparations for the network settings
Connecting
and then press ENTER (b) while [Start] is highlighted.
Network will automatically be connected to the unit.
2. Use
W/S/A/D
between [Dynamic] and [Static]. Normally, select [Dynamic] to allocate an IP address automatically.
Note
,
If there is no DHCP server on the network and you want to set the IP address manually, select [Static] then set [IP Address], [Subnet Mask], [Gateway] and [DNS Server] using
and numerical buttons. If you make a
A/D
mistake while entering a number, press CLEAR to clear the highlighted part.
3. Select [Next] and press ENTER (b) to apply network settings.
to select the IP mode
W/S/
Advanced Setting
If you want to set the network settings manually, use [Network Setting] menu and press ENTER (b).
1. Use
to select [Advanced Setting] on the
W/S
to select [Wired] and press ENTER
W/S
(b).
Network connection status is displayed on the screen.
4. Press ENTER (b) while [OK] is highlighted to finish the wired network settings.
Connecting 21

Wireless network connection

Another connection option is to use an Access Point or a wireless router. The network conguration and connection method may vary depending on the equipment in use and the network environment.
Wireless
Communication
DLNA certied servers
Access Point or Wireless Router
Broadband service
Refer to the setup instructions supplied with your access point or wireless router for detailed connection steps and network settings.
For best performance, a direct wired connection from this player to your home network’s router or cable/DSL modem is always the best option. If you choose to use the wireless option, please note that performance can sometimes be aected by other electronic devices in the home.

Wireless network setup

For the wireless network connection, the player needs to be set up for network communication. This adjustment can be done from the [Settings] menu. Adjust the [NETWORK] setting as follow. Setting up the access point or the wireless router is required before connecting the player to the network.
Preparation
Before setting the wireless network, you need to:
-connect the broadband internet to the wireless home network.
-set the access point or wireless router.
-note the SSID and security code of the network.
1. Select [Connection Setting] option in the [Settings] menu then press ENTER (b).
2. Read the preparations for the network settings and then press ENTER (b) while [Start] is highlighted.
If wired network is not connected to the unit, all available networks are displayed on the screen.
3. Use network and press ENTER (b).
to select a desired SSID of wireless
W/S
2
Connecting
If you have security on your access point, you need to input the security code as necessary.
Connecting22
Note
,
If you use other characters than the english alphabet or digits for the SSID name of your access point or wireless router, it may be displayed dierently.
2
Connecting
Note
,
yWEP security mode generally have 4 keys
available on an access point setting. If your access point or wireless router use WEP security, enter the security code of the key “No.1” to connect on your home network.
yAn Access Point is a device that allows you
to connect to your home network wirelessly.
4. Use
W/S/A/D
between [Dynamic] and [Static]. Normally, select [Dynamic] to allocate an IP address automatically.
Note
,
If there is no DHCP server on the network and you want to set the IP address manually, select [Static] then set [IP Address], [Subnet Mask], [Gateway] and [DNS Server] using
and numerical buttons. If you make a
A/D
mistake while entering a number, press CLEAR to clear the highlighted part.
5. Select [Next] and press ENTER (b) to apply network settings.
to select the IP mode
W/S/
Advanced Setting
If you want to set the network settings manually, use [Network Setting] menu and press ENTER (b).
1. Use
2. Follow the instructions of each connection
to select [Advanced Setting] on the
W/S
to select [Wireless] and press ENTER
W/S
(b).
[AP List] - Scans all available access points or wireless routers within range and display them as a list.
[Network name (SSID)] – Your access point may not be broadcasting its network name (SSID). Check your access point settings through your computer and either set your access point to broadcast SSID, or manually enter the network name in [Network name(SSID)].
[PBC] – If your access point or wireless router that supports the PBC (Push Button Configuration) method, select this option and press the Push Button on your access point within 120 counts. You do not need to know the network name (SSID) and security code of your access point.
[PIN] – If your access point supports the PIN Code configuration method based on WPS(Wi­Fi Protected Setup), select this option and note the code number on the screen. And then, enter the PIN number on a setting menu of your access point to connect. Refer to the documentation for your network device.
method on the screen.
Note
,
To use PBC and PIN network connection, security mode of your access point must be set to OPEN or AES.
Network connection status is displayed on the screen.
6. Select [OK] and press ENTER (b) to complete the network connection.
Connecting 23
Notes on network connection
yMany network connection problems during
set up can often be xed by re-setting the router or modem. After connecting the player to the home network, quickly power o and/ or disconnect the power cable of the home network router or cable modem. Then power on and/or connect the power cable again.
yDepending on the internet service provider (ISP),
the number of devices that can receive internet service may be limited by the applicable terms of service. For details, contact your ISP.
yOur company is not responsible for any
malfunction of the player and/or the internet connection feature due to communication errors/malfunctions associated with your broadband internet connection, or other connected equipment.
yThe features of BD-ROM discs made available
through the Internet Connection feature are not created or provided by our company, and our company is not responsible for their functionality or continued availability. Some disc related material available by the Internet Connection may not be compatible with this player. If you have questions about such content, please contact the producer of the disc.
ySome internet content may require a higher
bandwidth connection.
yEven if the player is properly connected and
congured, some internet content may not operate properly because of internet congestion, the quality or bandwidth of your internet service, or problems at the provider of the content.
ySome internet connection operations may not
be possible due to certain restrictions set by the Internet service provider (ISP) supplying your broadband Internet connection.
yAny fees charged by an ISP including, without
limitation, connection charges are your responsibility.
yA 10 Base-T or 100 Base-TX LAN port is required
for wired connection to this player. If your internet service does not allow for such a connection, you will not be able to connect the player.
yYou must use a Router to use xDSL service.
yA DSL modem is required to use DSL service and
a cable modem is required to use cable modem service. Depending on the access method of and
subscriber agreement with your ISP, you may not be able to use the internet connection feature contained in this player or you may be limited to the number of devices you can connect at the same time. (If your ISP limits subscription to one device, this player may not be allowed to connect when a PC is already connected.)
yThe use of a “Router” may not be allowed or its
usage may be limited depending on the policies and restrictions of your ISP. For details, contact your ISP directly.
yThe wireless network operate at 2.4 GHz
radio frequencies that are also used by other household devices such as cordless telephone, Bluetooth® devices, microwave oven, and can be aected by interference from them.
yTurn o all unused network equipment in
your local home network. Some devices may generate network trac.
yFor better reception, place the player from the
access point as close as possible.
yIn some instances, placing the access point or
wireless router at least 0.45 m (1.5 ft.) above the oor may improve the reception.
yThe reception quality over wireless depends on
many factors such as type of the access point, distance between the player and access point, and the location of the player.
ySet your access point or wireless router to
Infrastructure mode. Ad-hoc mode is not supported.
2
Connecting
System Setting24

Initial Setup

When you turn on the unit for the rst time, the initial setup wizard appears on the screen. Set the display language and network settings on the initial setup wizard.
1. Press 1 (POWER).
The initial setup wizard appears on the screen.
2. Use
W/S/A/D
and press ENTER (b).
3

System Setting

3. Read and prepare the preparations for the network settings and then press ENTER (b) while [Start] is highlighted.
to select a display language
5. Use
W/S/A/D
between [Dynamic] and [Static]. Normally, select [Dynamic] to allocate an IP address automatically.
6. Select [Next] and press ENTER (b) to apply network settings.
Network connection status is displayed on the screen.
For details on network settings, refer to “Connecting to Your Home Network” on page
19.
to select the IP mode
If wired network is connected, the network connection setting will automatically be finished.
4. All available networks are displayed on the screen. Use or desired SSID of wireless network and press ENTER (b).
If you have security on your access point, you need to input the security code as necessary.
to select [Wired Network]
W/S
Loading...
+ 56 hidden pages