LG S47413B User Manual

ENGLISH ESPAÑOL

OWNER’S MANUAL

ELECTRIC INDUCTION RANGE

Read this owner’s manual thoroughly before operating the appliance and keep it handy for reference at all times.

www.lg.com

MFL68881508_05

LSE4617** LSE4616**

TABLE OF CONTENTS

IMPORTANT SAFETY

INSTRUCTIONS

PRODUCT OVERVIEW

10 Parts 10 Accessories

INSTALLATION

11 Installation Overview 11 Product Specifications 12 Before Installing the Range 13 Installing the Range 15 Connecting Electricity 19 Engaging the Anti-tip Device 19 Optional Rear Filler 20 Test Run

OPERATION

21 Control Panel Overview 23 Knob Positions 24 Changing Oven Settings

24 Clock 24 Lockout 24 Minimum & Maximum Default Settings 25 Timer On/Off 25 Wi-Fi 25 Settings

-Setting the Hour Mode

-Setting Convection Auto Conversion

-Adjusting the Oven Temperature

-Turning the Preheat Alarm Light On/Off

-Adjusting the Oven Beeper Volume

-Selecting Fahrenheit or Celsius

-Turning the Cooktop Beeper On/Off 27 Start Time (Delayed Timed Cook) 27 Cook Time (Timed Cook) 27 Oven Light

28 Using the Cooktop

28 Cooking Areas 28 Benefits of Induction Surface Cooking 28 Induction Cookware 29 Cookware Placement 29 Moving Cookware on the Cooktop 29 Pan Sensing 30 Minimum and Maximum Pan Size 30 Hot Cookware and Residual Heat 30 Home Canning 31 Setting Surface Controls

31 Hot Surface Indicator 31 Using the Cooking Elements 32 The Recommended Surface Cooking

Setting 32 Pan Preheat Recommendations 32 Noises during Cooktop Operation 33 Power Management 33 Warming Zone

34 Using the Oven

34 Before Using the Oven 34 Oven Vent 34 Using Oven Racks 34 Bake 35 Convection Mode 36 Recommended Baking and Roasting Guide 37 Broil 38 Recommended Broiling Guide 39 Warm 39 Proof 39 Speed Roast 40 Meat Probe (For model: LSE4617) 41 Remote Start

41 Operating the Warming Drawer (For model:

LSE4617)

SMART FUNCTIONS

43 LG SmartThinQ Application 44 Smart Diagnosis™ Function 46 FCC Notice 46 FCC RF Radiation Exposure Statement

MAINTENANCE

47 Cleaning the Glass-Ceramic Cooktop 48 EasyClean

51 Self Clean 53 Changing the Oven Light 53 Cleaning the Exterior 54 Removing and Replacing the Lift-Off Oven

Doors and Drawer

55 Door Care Instructions

TROUBLESHOOTING

56 FAQs 58 Before Calling for Service

WARRANTY

IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

IMPORTANT SAFETY INSTRUCTIONS

Read and follow all instructions when using the range to prevent the risk of fire, electric shock, personal injury, or damage. This guide does not cover all possible conditions that may occur. Always contact your service agent or manufacturer about problems that you do not understand.

Download this owner's manual at: http://www.lg.com

This is the safety alert symbol. This symbol alerts you to potential hazards that can result in property damage and/or serious bodily harm or death. All safety messages will follow the safety alert symbol and either the word WARNING or CAUTION. These words mean:

WARNING

- Indicates a hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION

- Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.

ANTI-TIP DEVICE

WARNING

%TO REDUCE THE RISK OF TIPPING, THE APPLIANCE MUST BE SECURED

BY A PROPERLY INSTALLED ANTI-TIP DEVICE. TO CHECK IF THE DEVICE IS INSTALLED PROPERLY, REMOVE THE DRAWER BODY AND VERIFY THAT THE ANTI-TIP DEVICE IS ENGAGED, OR GRASP THE TOP REAR EDGE OF THE RANGE BACK GUARD AND CAREFULLY ATTEMPT TO TILT IT FORWARD. Refer to

the installation section for instructions.

%It is possible for a child or adult to tip the range and be killed.

%Verify that the anti-tip device has been properly installed and

attached to the floor or wall and engaged to the leveling leg of the range.

%Do not operate the range without the anti-tip device in place and

engaged.

%Never remove the oven legs. The range will not be secured to the

anti-tip bracket if the legs are removed.

%Do not step or sit on the oven door. The range could be tipped and

injury might result from spilled hot liquid, food, or the range itself.

%Do not rest large, heavy items such as whole turkeys on the open

oven door. The range could tip forward and cause injury.

%Reengage the anti-tip device after pulling the range out for

cleaning, service, or any other reason.

%Failure to follow these instructions can result in death or serious burns to children or

adults.

Anti-tip bracket

Leveling leg

IMPORTANT SAFETY INSTRUCTIONS

SAFETY PRECAUTIONS

WARNING

This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. (US only)

%DO NOT TOUCH HEATING ELEMENTS OR INTERIOR SURFACES OF OVEN. Heating

elements may be hot even though they are dark in color. Interior surfaces of an oven become hot enough to cause burns. During and after use, do not touch or let clothing or other flammable materials contact heating elements or interior surfaces of oven until they have had sufficient time to cool. Other surfaces, such as oven vent openings and surfaces near these openings, oven doors, and windows of oven doors, also get hot and may cause burns if not cooled.

%Use care when opening door. The hot air and steam that escape can cause burns to

hands, face and eyes. Let hot air or steam escape from the oven before removing or replacing food in the oven.

%Do not repair or replace any part of the appliance unless specifically recommended in the

manual. All other servicing should be performed by a qualified technician.

%Do not use harsh etching, abrasive cleaners or sharp metal scrapers to clean the oven

door glass since they can scratch the surface. Scratches may cause the glass to shatter.

WARNING

If the door glass, cooktop glass, surface, or oven heating unit of the range are damaged, discontinue use of the range and call for service.

%Do not operate the oven without the charcoal heater mesh. %Do not use plastic to cover food. Use foil or oven-safe lids only. %Do not allow anyone to climb, stand or hang on the door, storage drawer or cooktop. They

could damage the range and even tip it over, causing severe personal injury.

%Do not line the oven walls, racks, bottom, or any other part of the oven with aluminum foil

or any other material. Doing so will disrupt heat distribution, produce poor baking results and cause permanent damage to the oven interior (aluminum foil will melt to the interior

surface of the oven) %Never attempt to dry a pet in the oven. %Never use your appliance for warming or heating the room. %Always use pot holders or oven mitts when removing food from the oven or the surface

element. Cookware will be hot. Use only dry pot holders. Moist or damp pot holders on

hot surfaces may result in burns from steam. Do not let the pot holder touch hot heating

elements. Do not use a towel or other bulky cloth to remove food. %Do not heat unopened food containers. Pressure in the containers may cause them to

burst which may result in injury. %Before using Wi-Fi functions, open the oven door and make sure the oven is ready for pre-

heating. %If the supply cord is damaged, it must be replaced by the manufacturer, its service agent

or similarly qualified persons in order to avoid a hazard. %If the range is placed on a base, measures must be taken to prevent the appliance from

slipping off of the base. %To avoid the product overheating, do not install a decorative panel on the front of the

appliance. %To eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage

space located above the surface units should be avoided. If cabinet storage is to be

provided, the risk can be reduced by installing a range hood that projects horizontally a

minimum of 5 inches beyond the bottom of the cabinets.

IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

FLAMMABLE MATERIALS

WARNING

Remove all packing materials from the appliance before operating. Keep plastic, clothes, paper, and other flammable materials away from parts of the appliance that may become hot.

%Do not store or use flammable material in the oven or near or on the cooktop. Flammable

materials include paper, plastic, pot holders, linens, wall coverings, curtains, and gasoline

or other flammable vapors and liquids such as grease or cooking oil. These materials can

be ignited when the oven and cooktop are in use. %Wear proper apparel. Do not wear loose-fitting or hanging garments, which may ignite if

they contact hot surfaces, and cause severe burns. %Do not use the oven for drying clothes. Only use the oven for its intended purpose. %If cabinet storage is provided directly above cooking surface, place items that are not

frequently used and can be safely stored in an area subjected to heat. Temperatures may

be unsafe for volatile items such as flammable liquids, cleaners or aerosol sprays.

ELECTRICAL SAFETY

%Always disconnect power from the appliance before servicing. %Do not use aluminum foil or any other material to line the oven bottom.

Improper installation of these liners may result in a risk of electric shock or fire. %Do not allow aluminum foil or the temperature probe to contact heating elements. %Be sure your range is installed and grounded properly by a qualified installer or service

technician.

WARNING

Before replacing the oven light bulb, switch off the electrical power to the oven at the main fuse or circuit breaker panel. Failure to do so can result in severe personal injury, death, or electrical shock.

DEEP FAT FRYER

%Use extreme caution when moving or disposing of hot grease. %Always heat fat slowly, and watch as it heats. %If frying combinations of oils and fats, stir them together before heating. %Use a deep fat thermometer, if possible, to prevent overheating fat beyond the smoking

point. %Use the least possible amount of fat for effective shallow or deep-fat frying. Filling the pan

with too much fat can cause spillovers when food is added.

CHILD SAFETY

%Do not touch the hot surface between the bottom of the oven door and the top of the

drawer on the front of the oven while the oven is in operation. The surface becomes hot

and can cause burns and other injury. %Do not leave small children unattended near the oven.

IMPORTANT SAFETY INSTRUCTIONS

WARNING

Do not leave children alone or unsupervised near the appliance when it is in use or is

still hot. Children should never be allowed to sit or stand on any part of the appliance as they could be injured or burned.

CAUTION

Do not store items of interest to children in cabinets above a range or on the back guard of a range – children climbing on the range to reach items could be seriously injured.

%Never let a child hang on the oven door. %Do not allow children to crawl into the oven. %Let hot utensils cool in a safe place, out of reach of small children. %Children should be supervised to ensure that they do not play with the appliance.

WARNING

%The appliance and its accessible parts become hot during use. Do not touch heating

elements inside the oven. Young children must be continuously supervised if allowed near the appliance.

%This appliance is not intended for use by persons (including children) with reduced

physical, sensory or mental capabilities, or lack of experience and knowledge, unless they

have been given supervision or instruction concerning use of the appliance by a person

responsible for their safety. Do not allow children to play with the appliance. Any cleaning

and user maintenance performed by children must be supervised.

GLASS-CERAMIC COOKING SURFACE

%Surface units may be hot even though they are dark in color. Areas near surface units may

become hot enough to cause burns. During and after use, DO NOT TOUCH SURFACE

UNITS OR AREAS NEAR UNITS or let clothing or other flammable materials contact

surface units or areas near units until they have had sufficient time to cool. This includes

the cooktop and the area above the oven door. %Do not cook on a broken cooktop. If the cooktop is broken, cleaning solutions and

spillovers may penetrate the broken cooktop and create a risk of electric shock. Switch off

the appliance to avoid the possibility of electric shock and contact a qualified technician

immediately. %Do not use the glass cooktop surface as a cutting board. %Do not place or store items that can melt or catch fire on the glass cooktop, even when it

is not being used. %Choose proper burner size. For smaller pots and pans, use the smaller heating

elements. For larger pots and pans, use the larger heating elements. Select pans that

have flat bottoms large enough to cover the heating elements. Using undersized pans

exposes a portion of the heating element to direct contact and may result in clothing

burning. %Glazed cookware. Only certain types of glass, glass-ceramic, ceramic, earthenware,

or other glazed cookware are suitable for range-top service without breaking due to the

sudden change in temperature. %Never cook directly on the glass. Always use cookware. %Always turn the surface units off before removing cookware. Do not rely on the pan

sensor.

IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

WARNING

Do not leave fats or oils to heat unattended on the cooktop. Spillovers can result in a fire.

%The cooktop is not intended to be operated by means of an external timer or separate

remote-control system. %Turn cookware handles inward so they don't extend over adjacent surface units.

This reduces the risk of burns, ignition of flammable materials, and spillage due to

unintentional contact with the cookware. %Immediately clean spills on the cooking area to prevent a tough cleaning chore later. %Some cleaners can produce dangerous fumes if applied to a hot surface. %Do not place metallic objects such as knives, forks, spoons, and lids on the cooktop

surface, because they can get hot. %Always place the pan in the center of the surface unit you are cooking on. Never leave

surface units unattended at high heat settings. Proper contact of cookware to burner

also will improve efficiency. Boilovers cause smoking and greasy spills that may catch on

fire. %Clean cooktop with caution. Do not use sponges or cloth to wipe spills on a hot cooking

area. Use a proper metal scraper. If a wet sponge or cloth is used to wipe spills on a hot

cooking area, it can cause steam burns. Some cleaners can produce noxious fumes if

applied to a hot surface. %Do not turn surface units on before placing cookware. %Do not store heavy items above the cooktop surface that could fall and damage it. %Do not place aluminum foil or plastic items such as salt and pepper shakers, spoon

holders, or plastic wrappings or any other material on the range when it is in use. %Do not use a steel-wool pad or scrub pad or abrasive cleaning pads. They can scratch the

surface.

ENERGY SAVING TIPS

%Multiple-rack cooking saves time and energy. Whenever possible, cook foods requiring the

same cooking temperature together in one oven. %For optimal performance and energy savings, follow the guides on page 36 for proper rack

and pan placements. %Match the size of the cookware to the amount of food being cooked to save energy when

heating. Heating ½ quart of water requires more energy in a 3-quart pot than in a 1-quart

pot. %Use cookware with flat bottoms to provide the best contact with the cooktop surface when

cooking on the glass-ceramic cooktop. %Match the size of the cooktop burner or element to the size of the cookware in use. Using

a large element for a small pan wastes heating energy, and the exposed surface of the

element is a burn or fire hazard. %Reduce energy use by cleaning light oven soils with the EasyClean

feature instead of

self-clean. %Avoid opening the oven door more than necessary during use. This helps the oven

maintain temperature, prevents unnecessary heat loss, and saves on energy use.

IMPORTANT SAFETY INSTRUCTIONS

SAFETY DURING USE

CAUTION

Supervise all cooking processes. Continuously supervise quick cooking processes.

%During use the appliance becomes hot. Care should be taken to avoid touching heating

elements inside the oven. %Do not touch the oven racks while they are hot. %Do not block the vent opening. %Only arrange oven racks when the oven is cool. %If a rack must be moved while the oven is hot, do not let the pot holder contact the hot

heating element in the oven. %Use caution with the Timed Cook or Delayed Timed Cook features. Use the automatic

timer when cooking cured or frozen meats and most fruits and vegetables. Foods that can

easily spoil, such as milk, eggs, fish, meat or poultry, should be chilled in the refrigerator

first. Even when chilled, they should not stand in the oven for more than 1 hour before

cooking begins, and should be removed promptly when cooking is complete. Eating

spoiled food can result in sickness from food poisoning. %Accessible parts may become hot when the grill is in use. %Do not place food or cookware on the bottom of the oven cavity. Doing so will cause

permanent damage to the oven bottom finish. %Only use the temperature probe recommended for this oven. %Do not use water on grease fires. Should an oven fire occur, leave the oven door closed

and turn the oven off. If the fire continues, throw baking soda on the fire or use a fire

extinguisher. Do not put water or flour on the fire. Flour may be explosive and water can

spread a grease fire and cause personal injury. %Pull the oven rack to the stop-lock position when loading and unloading food from the

oven. This helps prevent burns caused by touching hot surfaces of the door and oven

walls. %Do not use the oven if a heating element develops a glowing spot during use or shows

other signs of damage. A glowing spot indicates the heating element may fail and present

a potential burn, fire, or shock hazard. Turn the oven off immediately and have the heating

element replaced by a qualified service technician. %When using cooking or roasting bags in the oven, follow the manufacturer’s directions.

SAFETY WHEN CLEANING

CAUTION

Remove food, cookware, racks, and accessories from the oven before operating the self-cleaning function. Remove any items placed in the bottom drawer.

%Avoid touching the door, window, or oven vent area during a cleaning cycle, and keep

children away from the appliance. These surfaces may get hotter than usual. %Do not use a steam cleaner to clean the oven. %Open a window or turn on a ventilation fan or hood before self-cleaning. %If the oven is heavily soiled with oil, self-clean the oven before using the oven again. The

oil could cause a fire. %Wipe up heavy soil on the bottom of the oven or the excess spillage before using the Self

Clean function. %Do not use oven cleaners. Commercial oven cleaner or oven liner protective coating of

any kind should not be used in or around any part of the oven.

IMPORTANT SAFETY INSTRUCTIONS

ENGLISH

%Never keep pet birds in the kitchen. The health of birds is extremely sensitive to the fumes

released during an oven self-clean cycle. Fumes may be harmful or fatal to birds. Move

birds to a well-ventilated room. %Clean in the self-clean cycle only parts listed in this manual. Before self-cleaning the oven,

remove the broiler pan, all oven racks, the meat probe and any utensils or food from the

oven. %Important Instruction. The oven displays an F error code and sounds three long beeps

during the self-cleaning process if it malfunctions in the self-clean mode. Switch off the

electrical power to the main fuse or breaker and have the oven serviced by a qualified

technician. %It is normal for the cooktop of the range to become hot during a self-clean cycle.

Therefore, touching the cooktop during a self-clean cycle should be avoided. %Never pour cold water over a hot oven for cleaning. Doing so may cause the oven to

malfunction. %Make sure oven lights are cool before cleaning. %Do not clean door gasket. The door gasket is essential for a good seal. Care should be

taken not to rub, damage, or move the gasket. %If there is a fire in the oven during self-clean, turn the oven off and wait for the fire to go

out. Do not force the door open. Introduction of fresh air at self-clean temperatures may

lead to a burst of flame from the oven. Failure to follow this instruction may result in severe

burns.

COOK MEAT AND POULTRY THOROUGHLY

%To protect against food-borne illnesses, cook meat and poultry thoroughly. The USDA has

indicated the following as safe minimum internal temperatures for consumption:

%Ground meats: 160 °F %Poultry: 165 °F %Beef, veal, pork, or lamb: 145 °F %Fish/seafood: 145 °F

PRODUCT OVERVIEW

Parts

Warming drawer (For Model: LSE4617)

Storage drawer (For Model: LSE4616)

Cooktop

Glass-ceramic

Cooktop controller

Model and serial number plate

Gasket

Oven door

Cooktop knob

Oven mode knob

Accessories

Included Accessories

For Model: LSE4617

Heavy rack (2ea) Gliding rack (1ea) Meat probe (1ea) Bottom rack (1ea)

Cleaner

Cooktop cleaner

(1ea)

Spray bottle

(1ea)

Non-scratch

scouring pad (1ea)

For Model: LSE4616

Cleaner

Standard Rack (3ea) Cooktop cleaner

(1ea)

Spray bottle

(1ea)

Non-scratch scouring pad

(1ea)

Optional Accessories

Grid Broiler pan

NOTE

%Contact LG Customer Service at 1-800-243-0000 (1-888-542-2623 in Canada) if any accessories are

missing. %For your safety and for extended product life, only use authorized components. %The manufacturer is not responsible for product malfunction or accidents caused by the use of separately

purchased, unauthorized components or parts. %The images in this guide may be different from the actual components and accessories, which are subject

to change by the manufacturer without prior notice for product improvement purposes.

INSTALLATION

ENGLISH

INSTALLATION

Installation Overview

Please read the following installation instructions first after purchasing this product or transporting it to another location.

Check and choose the

proper location

Plug in the power cord Engage the anti-tip device Test run

Install anti-tip device Level the range Connect electric range

Conduit connection plate

Black White Red

Terminal block

240 V

Product Specifications

The appearance and specifications listed in this manual may vary due to constant product improvements.

Oven Range Models LSE4617, LSE4616

Description Electric Induction Slide In Oven Range

Electrical requirements

LSE4617: 12.7 kW 120/240 VAC or 10.5 kW 120/208 VAC LSE4616: 11.6 kW 120/240 VAC or 9.8 kW 120/208 VAC

Exterior Dimensions

(W) x 37 7/

(H) x 26 1/

(D) (D with door closed)

75.7 cm (W) x 96 cm (H) x 67.3 cm (D) (D with door closed)

Height to cooking surface 36

(91.4 cm)

Net weight

LSE4617: 198.4 lb (90.0 kg) LSE4616: 191.8 lb (87.0 kg)

Total capacity Total cap.: 6.3 cu. ft.

INSTALLATION

Before Installing the Range

WARNING

Tip - Over Hazard

A child or adult can tip the range and be killed. Verify the anti-tip bracket has been installed. Ensure the anti-tip bracket is engaged when the range is moved. Do not operate the range without the anti-tip bracket in place. Failure to follow these instructions can result in death or serious burns to children and adults.

To check that leveling leg is inserted into anti-tip bracket, grasp the top rear edge of the range and carefully attempt to tilt it forward.

Anti-tip bracket

Leveling leg

If you did not receive an anti-tip bracket with your purchase, call 1-800-243-0000 (1-888-542-2623 in CANADA) to receive one at no cost.

WARNING

%The information in this manual should be

followed exactly. Failure to do so may result in fire, electrical shock, property damage, personal injury, or death.

%Wear gloves during the installation

procedure. Failure to do so can result in bodily injury.

Parts not Provided

4-Wire cord or

3-Wire cord

(UL approved 40 or 50

AMP)

Strain relief

(For conduit

Installations only)

Tools Needed

Phillips screwdriver

Level

Flat-blade screwdriver

Adjustable wrench

/4" Nut driver

Drill

Pliers

Safety glasses

Tape measure

Gloves

Parts Provided

Template (1) Anti-tip bracket kit (1)

Anchor sleeves (6) Lag bolts (6)

5HDU¿OOHU

NOTE

%Observe all governing codes and ordinances. %Have the installer show you the location of the circuit breaker or fuse. Mark it for easy reference. %As when using any appliance generating heat, there are certain safety precautions you should follow. %Be sure your range is installed and grounded properly by a qualified installer or service technician.

INSTALLATION

ENGLISH

Installing the Range

Unpacking and Moving the Range

CAUTION

%Use two or more people to move and install

the range. (Excessive Weight Hazard) Failure

to do so can result in back or other injury. %Do not use the door handles to push or

pull the range during installation or when

moving the range out for cleaning or

service. Doing so can result in serious damage

to the door of the range.

Remove packing material, tape and any temporary labels from your range before using. Do not remove any warning-type labels, the model and serial number label, or the Tech Sheet that is located on the back of the range.

To remove any remaining tape or glue, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove tape or glue. These products can damage the surface of your range.

Your range is heavy and can be installed on soft floor coverings such as cushioned vinyl or carpeting. Use care when moving the range on this type of flooring. Use a belt when moving the range to prevent damaging the floor. Or slide the range onto cardboard or plywood to avoid damaging the floor covering.

Choosing the Proper Location

CAUTION

%Avoid placing cabinets above the range. To

minimize the hazard caused by reaching over the open flames of operating burners, install a ventilation hood over the range that projects forward at least five inches beyond the front of the cabinets.

%Make sure wall covering, countertop and

cabinets around the range can withstand the heat (up to 194 °F) generated by the range. Discoloration, delamination or melting

may occur. This range has been designed to comply with the maximum allowable wood cabinet temperature of 194 °F.

%Before installing the range in an area

covered with linoleum or other synthetic floor covering, make sure the floor covering can withstand temperatures of at least 200 °F (93 °C).

%Use an insulated pad or

/4 in. (0.64 cm) plywood under the range if installing the range over carpeting.

The range should always be plugged into its own individual properly grounded electrical outlet. This prevents overloading house wiring circuits which could cause a fire hazard from overheated wires. It is recommended that a separate circuit serving only this appliance be provided.

Mobile Home - Additional Installation Requirements

The installation of this range must conform to the Manufactured Home Construction and Safety Standard, Title 24 CFR, Part 3280 (formerly the Federal Standard for Mobile Home Construction and Safety, Title 24, HUD Part 280), or when such standard is not applicable, the Standard for Manufactured Home Installations, ANSI A225.1/NFPA 501A or with local codes.

%When this range is installed in a mobile home, it

must be secured to the floor during transit. Any method of securing the range is adequate as long as it conforms to the standards listed above.

%A four-wire power supply cord or cable must be

used in a mobile home installation.

INSTALLATION

Dimensions and Clearances

NOTE

Save for the use of the local electrical inspector.

36"

(91.4 cm)

29.8"

(75.7 cm)

24"

(60.9 cm)

Cabinet

Cabinet opening

Acceptable electrical outlet area

3" (7.6 cm)

24"

(60.9 cm)

3" (7.6 cm)

25"

(63.5 cm)

Normal counter top depth

36" (91.4 cm)

Counter top height

(10 cm)

(23 cm)

(10 cm)

Wall

Center

15" (38 cm)

11" (28 cm)

2.5" (6.3 cm)

(15.2 cm)

5" (13 cm)

(15.2 cm)

2.5"

(6.3 cm)

A = 30" (76.2 cm) For U.S.A = 30" (76.2 cm) ~ 31" (78.7 cm) For CANADA

For installation in Canada, a free-standing range is not to be installed closer than

(12 mm) from any

adjacent surface.

30"

(76.2 cm)

*30" (76.2 cm)

Minimum

**15"

(38.1 cm)

36"

(91.4 cm)

Minimum Dimensions

* 30" (76.2 cm) minimum clearance between the top of the cooking surface and the bottom of an unprotected wood or metal cabinet; or 24" (60.9 cm) minimum when bottom of wood or metal cabinet is protected by not less than

(6.4 cm) flame retardant millboard covered with not less than no. 28 MSG sheet steel, 0.015" (0.381 mm)

stainless steel, 0.024" (0.610 mm) aluminum or 0.020" (0.508 mm) copper. ** 15" (38.1 cm) minimum between countertop and adjacent cabinet bottom.

INSTALLATION

ENGLISH

Installing the Anti-tip Device

Anti-tip bracket

Leveling leg

WARNING

Tip - Over Hazard

To check that leveling leg is inserted into anti-tip bracket, grasp the top rear edge of the range and carefully attempt to tilt it forward.

Wall plate

Anti-tip bracket

Screw must enter wood or concrete

Locate the anti-tip bracket using the template

An anti-tip bracket is packaged with the template. The instructions include necessary information to complete the installation. Read and follow the range installation instruction sheet (template).

Leveling the Range

Level the range by adjusting the leveling legs with a wrench. Extending the legs slightly may also make it easier to insert the rear leg into the anti-tip bracket.

Use a level to check your adjustments. Place the level diagonally on the oven rack, and check each direction for level.

First check direction

Then check direction

. If the level doesn’t show level

on the rack, adjust the leveling legs with a wrench.

Connecting Electricity

Electrical Requirements

This appliance must be installed and grounded on a branch circuit by a qualified technician in accordance with the National Electrical code ANSI/NFPA NO. 70 latest edition.

All wiring should conform to Local and NEC codes. This range requires a single-phase, 3 wire, A.C 120/208 V or 120/240 V 60 Hz electrical system. Use only a 3-conductor or a 4-conductor UL- listed range cord with closed-loop terminals, open-end spade lugs with upturned ends or similar termination. Do not install the power cord without a strain relief.

A range cord rated at 40 amps with 120/240 minimum volt range is required. If a 50 amp range cord is used, it should be marked for use with 1

diameter connection openings. This appliance may be connected by means of a conduit or power cord. If a conduit is being used, go to page 18 for

3 wire conduit connections or 4 wire conduit connections.

INSTALLATION

WARNING

%Allow 2 to 3 ft (61.0 cm to 91.4 cm) of slack

in the line so that the range can be moved if servicing is ever necessary.

%The power supply cord and plug should

not be modified. If it will not fit the outlet, have a proper outlet Installed by a qualified electrician.

%Using an extension cord to connect the

power is prohibited. Connect the power cord and plug directly.

%Electrical ground is required on this

appliance.

%Make sure that the power cord is not

pinched by the range or heavy objects.

Failure to do so can result in serious burns or electrical shock.

Specified power-supply-cord kit rating

Range rating, watts

Specified

rating of

power

supply-

cord kit,

amperes

Diameter (inches)

of Range

connection

Opening

120/240

volts

3-wire

120/208

volts

3-wire

Power

cord

Conduit

8,750 16,500

16,501 22,500

7,801 12,500

12,501 18,500

40 or 50A

1 3/

1 1/

1 3/

3, 4 - Wire electrical wall Receptacle

4 Wire receptacle (14-50R)

3 Wire receptacle (10-50R)

Connecting the Power Cord

The rear access cover must be removed. Loosen the two screws with a screwdriver. The terminal block will then be accessible.

Access cover

Use the cord/conduit connection plate to install the power cord or conduit. Leave the connection plate as installed for power cord installations. Remove the connection plate for conduit installations and use the smaller 11/8 in. (2.8 cm) conduit hole instead of the 13/8 in. (3.5 cm) power cord hole.

Remove the conduit connection plate

/8"

(2.8 cm) Conduit

13/8"

(3.5 cm) Cord

For power cord installations, hook the strain relief over the 13/8 in. (3.5 cm) power cord hole located below the rear of the oven. Insert the power cord through the strain relief and tighten it.

Conduit connection plate

Power cord

Assembling power cord strain relief at the 1

/8" opening

For conduit installations, insert the conduit strain relief in the 11/8 in. (2.8 cm) conduit hole. Then install the conduit through the body of the strain relief and fasten the strain relief with its ring.

Cord/ Conduit connection plate

Conduit

Ring

Body

Assembling conduit cord strain relief at the 1

/8" opening

INSTALLATION

ENGLISH

3-Wire Connection : Power Cord

WARNING

%The middle (neutral or ground) wire, which

is white, of a 3-wire power cord or a 3-wire conduit has to be connected to the middle post of the main terminal block. The remaining two wires of the power cord or conduit have to be connected to the outside posts of the main terminal connection block.

Failure to do so can result in electrical shock, severe personal injury or death.

Install the power cord as follows:

For power cord installations, hook the strain relief over the power cord hole (1

) located below the rear of the oven. Insert the power cord through the strain relief and tighten it.

Do not install the power cord without a strain relief.

Remove the lower 3 screws from the terminal block and retain them.

Insert the 3 screws through each power cord terminal ring and into the lower terminals of the terminal block. Make sure that the center (neutral) wire, which is white, is connected to the center lower position of the terminal block.

Tighten the 3 screws securely into the terminal block. Do not remove the ground strap connections.

3-wire connection

Black White Red

Terminal block

Conduit connection plate

If screws are not tightened securely, it can result in electrical spark and severe personal injury or death.

4-Wire Connection : Power Cord

WARNING

%Only a 4-conductor power-supply cord

kit rated 120/240 volts, 50 amperes and marked for use with ranges with closedloop connectors or opened spade lugs with upturned ends shall be used. The white middle (neutral) wire of the power cord or 4-wire conduit has to be connected to the middle post of the main terminal block. The other two wires of the power cord or conduit have to be connected to the outside posts of the main terminal connection block. The 4th ground wire (green) must be connected to the frame of the range with the ground screw. Failure

to do so can result in electrical shock, severe personal injury or death.

Install the power cord as follows: Do not install the power cord without a strain

relief.

Remove the lower 3 screws from the terminal block and retain them.

Remove the ground screw and bend the end of the ground strap up so the slot is over the hole of the center screw removed in step 1.

Insert the ground screw into the power cord ground wire (green) terminal ring and secure it to the range frame.

Insert the 3 screws through each power cord terminal ring and into the lower terminals of the terminal block. Make sure that the white center (neutral) wire is connected to the center lower position of the terminal block.

Tighten the 3 screws securely into the terminal block. The center screw now attaches the bent up ground strap to the block.

4-wire connection

Ground strap

Terminal block

Conduit connection plate

Ground screw

Black White Red

Bend strap up and attach

If screws are not tightened securely, it can result in electrical spark and severe personal injury or death.

INSTALLATION

3-Wire Connection: Conduit

Install the conduit as follows:

Remove the conduit connection plate from the rear of the oven and rotate it. The conduit hole (1

/8") must

be used. First, prepare the conduit wires as shown below.

3-Wire

Conduit connection plate

Ground wire

4-Wire

Second, install the conduit strain relief. For conduit installations, purchase a strain relief and

insert it in the 1

/8 in. (2.8 cm) conduit hole. Then install the conduit through the body of the strain relief and fasten the strain relief with its ring. Reinstall the bracket. For conduit connections: If the wire in the conduit is copper it must be 8 or 10 AWG wiring. If the wire in the conduit is aluminum it must be 6 or 8 AWG wiring.

Loosen the lower 3 screws from the terminal block.

Insert the bare wire (white/neutral) end through the center terminal block opening. Do not remove the ground strap connections.

Insert the two side bare wire ends into the lower left and the lower right terminal block openings. Tighten the 3 screws securely into the terminal block. (approximately 35 - 50 IN-LB)

3-wire connection

Terminal block

Black White Red

Wire ends

Conduit connection plate

If screws are not tightened securely, it can result in electrical spark and severe personal injury or death.

4-Wire Connection: Conduit

WARNING

%The white middle (neutral) wire of the power

cord or 4-wire conduit has to be connected to the middle post of the main terminal block. The other two wires of the power cord or conduit have to be connected to the outside posts of the main terminal connection block. The 4th ground wire (green) must be connected to the frame of the range with the ground screw. Failure

to do so can result in electrical shock, severe personal injury or death.

Follow the instructions for installing the conduit under 3-Wire Connection: Conduit until the strain relief and bracket are installed. Do not install the conduit without a strain relief.

Loosen the 2 lower left and right screws from the terminal block. Remove the lower 2 center screws. Do not discard any screws.

Remove the ground screw and bend the end of the ground strap up so the slot is over the hole of the center screw removed in step 1.

Attach the ground (green) bare wire end to the range frame and secure it in place with the ground screw.

Insert the bare wire (white/neutral) end through the center terminal block opening. The center screw now attaches the bent up ground strap to the block.

Insert the two side bare wire ends into the left and the right terminal block openings. Tighten the 3 screws securely into the terminal block. (approximately 35 - 50 IN-LB)

4-wire connection

Terminal block

Black White Red

Ground strap

Wire ends

Conduit connection plate

Bend strap up and attach

Ground wire

Ground screw

If screws are not tightened securely, it can result in electrical spark and severe personal injury or death.

INSTALLATION

ENGLISH

Engaging the Anti-tip Device

%Move the range close enough to the opening to

plug into the receptacle.

%Slide the range into position ensuring that the back

leg slides under the anti-tip bracket. The range should sit flush against the back wall when properly installed.

%Carefully attempt to tip the range forward to ensure

that the anti-tip bracket is engaged properly. If properly installed, the anti-tip bracket will prevent the range from being tipped. If the range can be tipped, reinstall the range until the anti-tip bracket is properly installed and the range will not tip forward.

%Turn on electrical power. Check the range for

proper operation.

Optional Rear Filler

If the counter does not bridge the opening at the rear wall the rear filler kit, that is provided with the slide in range, will be needed.

NOTE

If the countertop depth is greater than 25" there will be a gap between the filler kit and the back wall.

If the countertop depth is less than 24", the control panel will not sit flush with the countertop.

Installing the Rear Filler

Using a screwdriver, remove the six screws holding the rear bracket in place and remove the bracket.

Remove

Rear bracket

Attach the rear filler to the range back, sliding the hooks into the slots as shown. Slide the rear bracket into the bottom opening in the rear filler.

hook

5HDU¿OOHU

INSTALLATION

Attach the rear bracket and filler assembly as shown, using four of the six screws removed in step 1.

Lower screws

Slot

Store the remaining two screws with these instructions for future use.

Test Run

Check if the range is properly installed and run a test cycle.

Turn the oven mode knob to the Off position to start test.

Fill an induction-capable pot with water and place it on a surface element. Turn on the surface element. The LED bar should show the setting and the water should heat. The LED bar should not fluctuate. Repeat for all surface elements.

After checking all the surface heating elements, check the locking system by pressing Probe(LSE4617 Model only) or Clock for three seconds. The oven door should lock and the cooktop should not operate while the Lockout function is turned on. Press Probe(LSE4617 Model only) or Clock for three seconds to disable Lockout.

Now check the oven's operation. Turn the oven mode knob to select the Bake mode. 350 °F appears in the display. Press Start.

The oven should finish preheating in 15 minutes, and the convection fan should operate while the oven is preheating.

After checking the oven's operation, turn the temperature up to 450 °F and leave the oven on for at least an hour to help remove any oil which might cause smoke and odors when first using the oven.

NOTE

Smoke may come out of the range when it is first used.

OPERATION

ENGLISH

OPERATION

Control Panel Overview

For Model: LSE4617

3UHVVDQGKROGVHFIRUH[WUDIXQFWLRQV

:L)L

1 11

2 3 4 5 6 7 108 9

For Model: LSE4616

12 13 14 5 6 15 108 9

OPERATION

Smart Diagnosis

%Use during the Smart Diagnosis feature.

Cook Time / Clock (For Model: LSE4617)

%Press the button to set the desired amount of time

for food to cook. The oven shuts off when the set cooking time runs out.

%Press and hold button for three seconds to set the

time of day.

Start Time / Setting (For Model: LSE4617)

%Press the button to set the delayed timed cook. The

oven starts at the set time.

%Press and hold button for three seconds to select

and adjust oven settings.

Probe / Lock Out (For Model: LSE4617)

%Press the button to select Probe function. %Press and hold button for three seconds to lock or

unlock the door and control panel.

Timer On/Off / *Wi-Fi

Press the button to set or cancel timer on oven. Press and hold button for three seconds to connect the Wi-Fi. To disconnect the appliance from the network, delete it from the registered appliances in the app.

Oven Light

Press the button to turn oven light on or off.

Warming Drawer (For Model: LSE4617

Press the button to select the warming drawer function.

- /+

Press the plus button (+) to increase cooking time or oven temperature. Press the minus button (-) to decrease cooking time or oven temperature.

Start

Press the button to start all oven features.

Oven Mode Knob

Turn the knob to select oven operating mode.

Flashing Clock

If the colon in the clock display flashes, press Cook Time for three seconds and reset the clock, or press

any key to stop the flashing.

Cook Time (For Model: LSE4616)

Press the button to set the desired amount of time for food to cook. The oven shuts off when the set cooking time runs out.

Start Time (For Model: LSE4616)

Press the button to set the delayed timed cook. The oven starts at the set time.

Clock / Lock Out (For Model: LSE4616)

%Press button to set the time of day. %Press and hold button for three seconds to lock the

door and control panel.

Setting (For Model: LSE4616)

Press button to select and adjust oven settings.

OPERATION

ENGLISH

Knob Positions

After cleaning the oven knobs, make sure to replace each knob in the correct position. Failure to do so can result in improper operation of the burners.

1 2

Simmer

HI/Boos

Simmer

HI/Boos

Induction Oven Mode Warm Induction

Burner On Indicator

The Burner On indicator light turns on when the knob is turned even if the cooktop element does not operate.

Hot Surface Indicator

The hot surface indicator light glows as long as any surface cooking area is too hot to touch.

,WUHPDLQVRQDIWHUWKHHOHPHQWLVWXUQHGRIIDQGXQWLOWKHVXUIDFHKDVFRROHGWRDSSUR[LPDWHO\Û)

OPERATION

Changing Oven Settings

Clock

The clock must be set to the correct time of day in order for the automatic oven timing functions to work properly.

Set the oven mode knob to the Off position.

Press and hold Cook Time for three seconds (LSE4617 model only) or press Clock. CLO shows in the display.

Press plus(+) or minus(-) to select the desired time. Plus(+) to increase the time and minus(-) to decrease the time.

Press Start to enter the time and start the clock.

NOTE

%The time of day cannot be changed during a

timed baking or self-clean cycle.

%If no other keys are pressed within 25 seconds

of pressing Clock, the display reverts to the original setting.

%If the display colon in the clock is blinking, you

may have experienced a power failure. Reset the time.

Lockout

The Lockout feature automatically locks the oven door and prevents most oven from being turned on. It does not disable the timer and the interior oven light.

Set the oven mode knob to the Off position.

Press and hold Probe/Lockout (LSE4617 model only) or Clock/Lockout for three seconds.

The lock melody sounds, Loc appears in the display and the lock icon

blinks in the display.

Once the oven door is locked, the lock indicator stops blinking and remains on.

To deactivate the Lockout feature, press and hold Probe/Lockout (LSE4617 model only) or Clock/Lockout for three seconds. The unlock melody sounds and the door and the controls unlock.

NOTE

The Burner On indicator light turns on when the knob is turned even if the cooktop element does not operate.

Minimum & Maximum Default Settings

All of the features listed have a minimum and a maximum time or temperature setting that may be entered into the control. An entry acceptance beep sounds each time a control key is pressed.

An entry error tone (two short tones) sounds if the entry of the temperature or time is below the minimum or above the maximum setting for the feature.

Feature

min.

Temp. /

Time

max.

Temp. /

Time

Default

Clock

12 Hr.

1:00

Hr. / min.

12:59

Hr. / min.

24 Hr.

0:00

Hr. / min.