<![endif]>ESPAÑOL FRANÇAIS ENGLISH
INSTALLATION MANUAL
AIR
CONDITIONER
Please read this installation manual completely before installing the product. Installation work must be performed in accordance with the national wiring standards by authorized personnel only.
Please retain this installation manual for future reference after reading it thoroughly.
PRHR083A/PRHR063A/PRHR043A/PRHR033A/PRHR023A (Heat Recovery Unit)
Original instruction
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
http://www.lghvac.com |
|
|
MFL32987321 |
|
|
|
|
|
|
www.lg.com |
||||||||||||||
|
Rev.00_052418 |
|
|
|
|
|
|
Copyright © 2018 LG Electronics Inc. All Rights Reserved. |
<![endif]>ENGLISH
2 TIPS FOR SAVING ENERGY
TIPS FOR SAVING ENERGY
Here are some tips that will help you minimize power consumption when you use the air conditioner. You can use your air conditioner more efficiently by referring to the instructions below:
•Do not cool excessively indoors. This may consume more electricity.
•Block sunlight with blinds or curtains while you are operating the air conditioner.
•Keep doors or windows closed tightly while you are operating the air conditioner.
•Adjust the direction of the air flow vertically or horizontally to circulate indoor air.
•Clean the air filter once every 2 weeks. Dust and impurities collected in the air filter may block the air flow or weaken the cooling / dehumidifying functions.
For your records
Staple your receipt to this page in case you need it to prove the date of purchase or for warranty purposes. Write the model number and the serial number here:
Model number :
Serial number :
You can find them on a label on the side of each unit.
Dealer’s name :
Date of purchase :
IMPORTANT SAFETY INSTRUCTIONS 3
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
Always comply with the following precautions to avoid dangerous situations and ensure peak performance of your product
! WARNING
It can result in serious injury or death when the directions are ignored
! CAUTION
It can result in minor injury or product damage when the directions are ignored
! WARNING
•Installation or repairs made by unqualified persons can result in hazards to you and others.
•The information contained in the manual is intended for use by a qualified service contractor familiar with safety procedures and equipped with the proper tools and test instruments.
•Failure to carefully read and follow all instructions in this manual can result in equipment malfunction, property damage, personal injury and/or death.
! WARNING
•Have all electric work done by a licensed electrician according to "Electric Facility Engineering Standard" and "Interior Wire Regulations" and the instructions given in this manual and always use a special circuit.
-If the power source capacity is inadequate or electric work is performed improperly, electric shock or fire may result.
•Ask the dealer or an authorized contractor to install the HR unit.
-Improper installation by the user may result in water leakage, electric shock, or fire.
<![endif]>ENGLISH
|
4 |
IMPORTANT SAFETY INSTRUCTIONS |
|
|
|
<![if ! IE]> <![endif]>ENGLISH |
• Always ground the product. |
|
|
||
|
- There is risk of fire or electric shock. |
|
|
• Make the connections securely so that the outside force of |
|
|
||
|
the cable may not be applied to the terminals. |
|
|
- Inadequate connection and fastening may generate heat and |
|
|
|
cause a fire. |
|
• For re-installation of the installed product, always contact a |
|
|
dealer or an Authorized Service Center. |
|
|
- There is risk of fire, electric shock, explosion, or injury. |
|
|
• Do not install, remove, or re-install the unit by yourself |
|
|
(customer). |
|
|
- There is risk of fire, electric shock, explosion, or injury. |
|
|
- All work should be performed by a qualified, licensed |
|
|
|
contractor. |
|
• Do not store or use flammable gas or combustibles near the |
|
|
HR Unit. |
|
|
- There is risk of fire or failure of product. |
|
|
• Use a properly rated breaker or fuse. |
|
|
- There is risk of fire or electric shock. |
|
|
• Do not damage or use an unspecified power cord. |
|
|
- There is risk of fire, electric shock, explosion, or injury. |
|
|
• Do not touch the power switch with wet hands. |
|
|
- There is risk of fire, electric shock, explosion, or injury. |
|
|
• Securely install the cover of control box and the panel. |
|
|
- If the cover and panel are not installed securely, dust or |
|
|
|
water may enter the HR unit and fire or electric shock may |
|
|
result. |
|
• Be cautious when unpacking and installing the product. |
|
|
- Sharp edges could cause injury. Be especially careful of the |
|
|
|
case edges. |
|
• Safely dispose of the packing materials. |
|
|
|
- Packing materials, such as nails and other metal or wooden |
|
|
parts, may cause puncture wounds or other injuries. |
|
|
- Tear apart and throw away plastic packaging bags so that |
|
|
children may not play with them and risk suffocation and |
|
|
death. |
IMPORTANT SAFETY INSTRUCTIONS 5
! CAUTION
•Avoid a place where rain may enter since the HR unit is for indoor installations only.
-There is risk of property damage, failure of product, or electric shock.
•Do not install a HR unit in a space where persons exists such as living room, office or meeting room with not only low but also open ceiling.
•Always check for gas (refrigerant) leakage after installation or repair of product.
-Low refrigerant levels may cause failure of product.
•Keep level even when installing the product.
-To avoid vibration or water leakage.
•This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
-Children should be supervised to ensure that they do not play with the appliance.
<![endif]>ENGLISH
<![endif]>ENGLISH
6 |
TABLE OF CONTENTS |
|
|
|
TABLE OF CONTENTS
2TIPS FOR SAVING ENERGY
3IMPORTANT SAFETY INSTRUCTIONS
7FEATURES
9INSTALLATION PART
10 INSTALLATION
10 Selection of the best location
10 Dimensional drawings
13 HR Unit Installation
16Insulation
17Wiring Connection
18HR Unit PCB
19Setting the HR Unit switches
26COIL EXCHANGING METHOD
27JOINT METHOD OF HR UNIT
FEATURES 7
FEATURES
Control Box
Connection Pipe (to outdoor unit)
Connection Pipe
(to outdoor unit)
Connection Pipe (to indoor unit)
Model |
|
|
PRHR023A |
|
PRHR033A |
|
PRHR043A |
|
|
|
|
|
|
||
Max. Connectable No. of Indoor Units |
16 |
|
24 |
|
32 |
||
|
|
|
|
|
|
||
Max. Connectable No. of Indoor Units of a branch |
8 |
|
8 |
|
8 |
||
|
|
|
|
|
|
|
|
Power Input |
Cooling [W] |
|
|
39.8 |
|
|
|
|
|
|
|
|
|
|
|
Heating [W] |
|
|
37.2 |
|
|
||
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
Net. Weight |
kg |
|
14.9 |
|
16.7 |
|
18.2 |
|
|
|
|
|
|
|
|
lbs |
|
32.8 |
|
36.8 |
|
40.1 |
|
|
|
|
|
||||
|
|
|
|
|
|
|
|
Shipping |
kg |
|
20.7 |
|
22.5 |
|
24.0 |
|
|
|
|
|
|
|
|
Weight |
lbs |
|
45.6 |
|
49.6 |
|
52.9 |
|
|
|
|
||||
|
|
|
|
|
|
|
|
Dimensions |
mm |
|
|
|
786 X 218 X 657 |
|
|
|
|
|
|
|
|
|
|
(WxHxD) |
Inch |
|
|
|
30.9 X 8.6 X 25.9 |
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
Casing |
|
|
|
Galvanized steel plate |
|
||
|
|
|
|
|
|
|
|
|
|
Liquid Pipe |
|
Ø9.52[3/8] – Ø6.35[1/4] |
|
||
|
|
[mm/inch] |
|
|
|||
|
Indoor side |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Gas Pipe |
|
Ø15.88[5/8] – Ø12.7[1/2] |
||||
|
|
|
|||||
|
|
[mm/inch] |
|
||||
|
|
|
|
|
|
|
|
Connecting |
|
|
|
|
|
|
|
|
Liquid |
Ø9.52[3/8] |
|
Ø12.7[1/2] |
|
Ø15.88[5/8] |
|
Pipes |
|
[mm/inch] |
|
|
|||
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
Outdoor side |
Low Pressure |
Ø22.2[7/8] |
|
Ø28.58[1-1/8] |
|
Ø28.58[1-1/8] |
|
[mm/inch] |
|
|
||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
High Pressure |
Ø19.05[3/4] |
|
Ø22.2[7/8] |
|
Ø22.2[7/8] |
|
|
[mm/inch] |
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Sound Absorbing Insulation Material |
|
Polyethylene Foam |
|
||||
|
|
|
|
|
|
|
|
Current |
Minimum circuit Amps(MCA) |
|
0.17 |
|
|
||
|
|
|
|
|
|
|
|
Maximum fuse Amps(MFA) |
|
15 |
|
|
|||
|
|
|
|
||||
|
|
|
|
|
|
|
|
Power Supply |
|
|
|
1Ø, 208/230 V, 60 Hz |
|
||
|
|
|
|
|
|
|
|
<![endif]>ENGLISH
<![endif]>ENGLISH
8 FEATURES
Connection Pipe
(to outdoor unit)
Control Box
Connection Pipe
(to indoor unit)
Connection Pipe (to outdoor unit)
Model |
|
|
PRHR063A |
|
PRHR083A |
|
|
|
|
||
Max. Connectable No. of Indoor Units |
48 |
|
64 |
||
|
|
|
|
||
Max. Connectable No. of Indoor Units of a branch |
8 |
|
8 |
||
|
|
|
|
|
|
Power Input |
Cooling [W] |
75.9 |
|
||
|
|
|
|
|
|
Heating [W] |
72.1 |
|
|||
|
|
||||
|
|
|
|
|
|
Net. Weight |
kg |
|
27.2 |
|
30.7 |
|
|
|
|
|
|
lbs |
|
60.0 |
|
67.7 |
|
|
|
|
|||
|
|
|
|
|
|
Shipping |
kg |
|
33.8 |
|
37.3 |
|
|
|
|
|
|
Weight |
lbs |
|
74.5 |
|
82.2 |
|
|
|
|||
|
|
|
|
|
|
Dimensions |
mm |
|
1 113 X 218 X 657 |
||
|
|
|
|
|
|
(WxHxD) |
Inch |
|
43.8 X 8.6 X 25.9 |
|
|
|
|
|
|||
|
|
|
|
|
|
Casing |
|
|
Galvanized steel plate |
||
|
|
|
|
|
|
|
Indoor |
Liquid Pipe [mm/inch] |
Ø9.52[3/8] – Ø6.35[1/4] |
||
|
|
|
|
|
|
|
side |
Gas Pipe [mm/inch] |
Ø15.88[5/8] – Ø12.7[1/2] |
||
|
|
||||
Connecting |
|
|
|
|
|
|
Liquid [mm/inch] |
Ø15.88[5/8] |
|
||
Pipes |
|
|
|||
Outdoor |
|
|
|
|
|
|
Low Pressure [mm/inch] |
Ø28.58[1-1/8] |
|
||
|
side |
|
|
|
|
|
High Pressure [mm/inch] |
Ø22.2[7/8] |
|
||
|
|
|
|||
|
|
|
|
|
|
Sound Absorbing Insulation Material |
Polyethylene Foam |
||||
|
|
|
|
|
|
Current |
Minimum circuit Amps(MCA) |
0.27 |
|
||
|
|
|
|
|
|
Maximum fuse Amps(MFA) |
15 |
|
|||
|
|
||||
|
|
|
|
|
|
Power Supply |
|
|
1Ø, 208/230 V, 60 Hz |
||
|
|
|
|
|
|
INSTALLATION PART 9
INSTALLATION PART
-Installation Manual
-Hanging bolts (4 x M10 or M8), Nut(8 x M10 or M8), Flat washers(8 x M10)
-Reducers
[Unit : mm(inch)]
Gas pipe
Models |
Liquid pipe |
High pressure |
Low pressure |
|||||
|
|
|
||||||
PRHR023A |
|
|
OD19.05(3/4) |
Ø15.88(5/8) Ø12.7(1/2) |
OD22.2(7/8) Ø19.05(3/4) Ø15.88(5/8) |
|||
|
|
|
|
|||||
OD9.52(3/8) |
Ø6.35(1/4) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
||
HR unit |
|
|
OD12.7(1/2) |
Ø9.52(3/8) |
OD15.88(5/8) Ø12.7(1/2) |
|||
reducer |
|
|
|
|
|
|
|
|
PRHR033A |
|
|
OD22.2(7/8) |
Ø19.05(3/4) Ø15.88(5/8) |
|
|
||
PRHR043A |
OD15.88(5/8) Ø12.7(1/2) Ø9.52(3/8) |
OD28.58(1-1/8) Ø22.2(7/8) Ø19.05(3/4) |
||||||
PRHR063A |
|
|
|
|
|
|
|
|
PRHR083A |
|
|
|
|
|
|
|
|
|
OD12.7(1/2) |
Ø9.52(3/8) |
OD15.88(5/8) |
Ø12.7(1/2) |
OD19.05(3/4) |
Ø15.88(5/8) |
<![endif]>ENGLISH