LG PBACNBTR0, ZSMA01BMS, PBACNBTR0A Installation Manual

LG MultiSITE

Communications Manager

INSTALLATION MANUAL

Model Number: PBACNBTR0A

(PBACNBTR0 + ZSMA01BMS)

PROPRIETARY DATA NOTICE

This document, as well as all reports, illustrations, data, information, and other

materials are the property of LG Electronics U.S.A., Inc., and are

disclosed by LG Electronics U.S.A., Inc., only in confidence.

Do not throw away, destroy, or lose this manual.

Please read carefully and store in a safe place for future reference.

Content familiarity required for proper installation.

The instructions included in this manual must be followed to prevent prod-

uct malfunction, property damage, injury, or death to the user or other

people. Incorrect operation due to ignoring any instructions will cause

harm or damage. A summary of safety precautions begins on page 4.

For more technical materials such as submittals, engineering

databooks, and catalogs, visit www.lghvac.com.

For continual product development, LG Electronics U.S.A., Inc., reserves the right to change specifications without notice.

This document, as well as all reports, illustrations, data, information, and other materials are the property of LG Electronics U.S.A., Inc.

IM_MultiSITE_Communications_Manager_PBACNBTR0A_08_17

©LG Electronics U.S.A., Inc.

TABLE OF CONTENTS

Safety Instructions ....................................................................................................................................................................................... 4

Introduction .................................................................................................................................................................................................. 9

LG MultiSITETM Communications Manager Controller .................................................................................................................................................. 9

Items Included with the Controller ................................................................................................................................................................................ 9

Materials and Tools .................................................................................................................................................................................................... 10

Mounting Preparation ................................................................................................................................................................................ 11

Inserting or Removing the MicroSD Card ....................................................................................................................................................................11

Environmental Requirements ..................................................................................................................................................................................... 13

Mounting ................................................................................................................................................................................................... 14

Physical Mounting ...................................................................................................................................................................................................... 14

Mounting on DIN Rail ................................................................................................................................................................................................. 15

Wiring ........................................................................................................................................................................................................17

Earth Ground and Power ............................................................................................................................................................................................ 17

Communications Wiring .............................................................................................................................................................................................. 18

V-Net Wiring ............................................................................................................................................................................................................... 19

Ethernet Wiring ........................................................................................................................................................................................................... 19

Installation Manual

Power Up and Initial Checkout ..................................................................................................................................................................20

Status LEDs ..............................................................................................................................................................................................21

V-Net LEDs ................................................................................................................................................................................................................. 21

STAT (Status) LED ...................................................................................................................................................................................................... 22

BEAT (Heartbeat) LED ............................................................................................................................................................................................... 22

PRI, SEC (Ethernet) LEDs ......................................................................................................................................................................................... 22

Tab Mounting Dimensions .......................................................................................................................................................................23

Due to our policy of continuous product innovation, some specifications may change without notification.

SAFETY INSTRUCTIONS

DANGER

WARNING

CAUTION

DANGER

The instructions below must be followed to prevent product malfunction, property damage, injury or death to the user or other people. Incorrect operation due to ignoring any instructions will cause harm or damage. The level of seriousness is classified by the symbols described below.

TABLE OF SYMBOLS

This symbol indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

This symbol indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

This symbol indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

Note:

Safety of personnel is the primary concern during all procedures. Read and understand this safety summary. Read and understand the installation procedure before beginning installation. Use the appropriate tools and accessories during installation. Plan your work and do not work alone, if possible. Know how to obtain emergency medical and fire fighting assistance.

Do not use or store ammable gas or combustibles near the unit.

There is risk of re, explosion, and physical injury or death.

This symbol indicates situations that may result in equipment or property damage accidents only.

This symbol indicates an action that should not be performed.

Communications Manager

Disconnect power before installing or servicing the unit.

There is risk of physical injury or death due to electric shock.

Properly size all circuit breakers or fuses.

There is risk of re, electric shock, explosion, physical injury, or death.

LG MultiSITE

Do not share the electrical circuit with other devices.

There is risk of re, electric shock, physical injury, or death due to heat generation.

Do not use damaged or loose power wiring. Do not modify or extend the outdoor unit’s power wiring randomly. Ensure

that the power wiring will not be pulled nor weight be placed on the power wiring during operation.

There is risk of re, electric shock, and physical injury or death.

Due to our policy of continuous product innovation, some specifications may change without notification.

SAFETY INSTRUCTIONS

WARNING

The information contained in this manual is intended for use by an industry-qualied, experienced, trained electrician familiar with local, national, and regional codes and who is equipped with the proper tools and test instruments.

Failure to carefully read and follow all instructions in this manual can result in personal injury or death.

All electric work must be performed by a licensed electrician and conform to local building codes or, in the absence of local codes, with the National Electrical Code, and the instructions given in this manual.

If the power source capacity is inadequate or the electric work is not performed properly, it may result in re, electric shock, physical injury or death.

Use copper conductors only. Refer to local, state, and federal codes, and use power wires of sufcient current capacity and rating.

Wires that are too small may generate heat, cause a re and physical injury or death.

Before making power terminations during earth grounding, de-energize the 24V power source. Do not restore power until completing all other mounting and wiring.

There is risk of electric shock and physical injury or death.

Installation Manual

Install in a controlled environment relatively free of contaminants.

There is risk of electric shock and physical injury or death.

Secure all eld wiring connections with appropriate wire strain relief.

Improperly securing wires will create undue stress on equipment power lugs. Inadequate connections may generate heat, cause a re and physical

injury or death.

Ensure the system is connected to a dedicated power source that provides adequate power.

If the power source capacity is inadequate or the electric work is not performed properly, it may result in re, electric shock, physical injury or death.

Do not change the settings of the protection devices.

If the pressure switch, thermal switch, or other protection device is shorted and forced to operate improperly, or parts other than those specied by LG are used, there is risk of re, electric shock, explosion, and physical injury or death.

Properly tighten all power connections.

Loose wiring may overheat at connection points, causing a re, physical injury or death.

Dispose of any packing materials safely.

• Packing materials, such as nails and other metal or wooden parts may cause puncture wounds or other injuries.

• Tear apart and throw away plastic packaging bags so that children may not play with them and risk suffocation and death.

Do not install the MultiSITE Communications Manager unit if it will be exposed to rain or other precipitation. Do not

install the unit in a location exposed to open ame or extreme heat. Do not touch the unit with wet hands.

There is risk of re, electric shock, physical injury, and/or death.

Due to our policy of continuous product innovation, some specifications may change without notification.

SAFETY INSTRUCTIONS

CAUTION

Wear protective gloves when handling equipment.

Sharp edges may cause personal injury.

Note:

Failure to carefully read and follow all instructions in this manual can result in equipment malfunction or property damage.

Disconnect power before installing or servicing the unit.

There is risk of equipment damage or degraded performance.

MultiSITE Communications Manager is for use with select LG air conditioning systems only. Do not attempt to use this unit with any other type of system.

There is risk of equipment damage or degraded performance.

Clean up the site after all procedures are nished, and check that no metal scraps, screws, or bits of wiring have been left inside or surrounding the controller or indoor units.

Do not allow water, dirt, or animals to enter the controller.

There is risk of unit failure or degraded performance.

Communications Manager

Do not spill water or other liquid on the inside of the controller. Do not drop the controller into water. If the unit is

immersed in water or other liquid, contact your local authorized LG distributor for support.

There is risk of unit failure or degraded performance.

Remove all power to controller before attaching (plug in) or detaching (unplug) any option module.

There is risk of possible equipment damage.

LG MultiSITE

Do not remove the controller’s cover.

No congurable or user-serviceable items (such as jumpers or a battery) require cover removal. All items are accessible as switches and connectors

on the unit’s top, bottom, and side, or behind the unit’s front access door or microSD card shutter.

This device is only intended for use as a monitoring and control device. Do not use it for any other purpose.

There is risk of data loss or equipment damage.

Before removing or inserting the microSD card, disconnect all power to the controller and use static discharge precautions.

There is risk of equipment damage.

The MultiSITE Communications Manager controller is not compatible with a Power-Over-Ethernet (POE) network. Do not connect the controller on a network segment which carries power.

The unit may fail.

Due to our policy of continuous product innovation, some specifications may change without notification.

CERTIFICATIONS

The MultiSITE Communications Manager controller has the following agency listings, compliances, and certifications:

• UL-916, Energy Management Equipment - Edition 4

• FCC Part 15, Class B - Federal Communications Commission, with FCC Part 15, Subpart C - WiFi

• ICES-003, Class B - Industry Canada Interference-Causing Equipment Standard

• RoHS 2 (Restriction of Hazardous Substances), Directive 2011/65/EU.

CE Declaration of Conformity (Council Directive 004-108-EC)

ACMA, complies with the requirements of the relevant ACMA Standards. This document covers mounting and wiring of the following products.

Installation Manual

Due to our policy of continuous product innovation, some specifications may change without notification.

COMPLIANCE AND APPROVALS

Federal Communications Commission (FCC)

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy. If the equipment is not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Canadian Department of Communications (DOC)

This device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: 1) this device may not cause interference, and 2)this device must accept any interference, including interference that may cause undesired operation of the device.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain ap-

Communications Manager

proved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be

so chosen that the equivalent isotropically radiated power (EIRP) is not more than that necessary for successful communication.

The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems.

Approved Antenna Listing

• ANT-DB1-RAF-RPS

LG MultiSITE

Transmitter Module Listing

• Contains Transmitter Module FCC ID: W98-12977

• Contains Transmitter Module IC: 8339A-12977

To comply with FCC and Industry Canada RF exposure limits for general population /uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Due to our policy of continuous product innovation, some specifications may change without notification.

+ 16 hidden pages

LG PBACNBTR0, ZSMA01BMS, PBACNBTR0A Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual