LG OLED77W9PVA Owner’s Manual

Safety and Reference

Please read this manual carefully before operating your set and retain it for future reference.

*MFL71182433*

www.lg.com

(2012-REV03)

Copyright 2019 LG Electronics Inc. All Rights Reserved.

Warning! Safety Instructions

	<![if ! IE]> <![endif]>ENGLISH	CAUTION
		RISK OF ELECTRIC SHOCK
		DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s

enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing)

instructions in the literature accompanying the appliance.

WARNING: TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

•• TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER ITEMS WITH OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES.

•• Do not place the TV and/or remote control in the following environments:

-- Keep the product away from direct sunlight.

-- An area with high humidity such as a bathroom

-- Near any heat source such as stoves and other devices that produce heat.

-- Near kitchen counters or humidifiers where they can easily be exposed to steam or oil.

-- An area exposed to rain or wind.

-- Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g., on shelves above the unit).

-- Near flammable objects such as gasoline or candles, or expose the TV to direct air conditioning.

-- Do not install in excessively dusty places.

Otherwise, this may result in fire, electric shock, combustion/ explosion, malfunction or product deformation.

•• Ventilation

-- Install your TV where there is proper ventilation. Do not install in a confined space such as a bookcase.

-- Do not install the product on a carpet or cushion.

-- Do not block or cover the product with cloth or other materials while unit is plugged in.

•• Take care not to touch the ventilation openings. When watching the TV for a long period, the ventilation openings may become hot.

•• Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the device.

•• Do not move the TV whilst the Power cord is plugged in.

•• Do not use a damaged or loosely fitting power cord.

•• Be sure do grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.

•• Do not connect too many devices to the same AC power outlet as this could result in fire or electric shock.

•• Disconnecting the Device from the Main Power

-- The power plug is the disconnecting device. In case of an emergency, the power plug must remain readily accessible.

•• Do not let your children climb or cling onto the TV. Otherwise, the TV may fall over, which may cause serious injury.

•• Outdoor Antenna Grounding (Can differ by country):

-- If an outdoor antenna is installed, follow the precautions below. An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can come in contact with such power lines or circuits as death or serious injury can occur.

Be sure the antenna system is grounded to provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes and requirements for the grounding electrode. Antenna grounding according to the National Electrical Code, ANSI/NFPA 70

2

•• Grounding (Except for devices which are not grounded.)

-- TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet. Ensure that you connect the earth ground wire to prevent possible electric shock.

•• Never touch this apparatus or antenna during a lightning storm. You may be electrocuted.

•• Make sure the power cord is connected securely to the TV and wall socket if not secured damage to the Plug and socket may occur and in extreme cases a fire may break out.

•• Do not insert metallic or inflammable objects into the product. If a foreign object is dropped into the product, unplug the power cord and contact the customer service.

•• Do not touch the end of the power cord while it is plugged in. You may be electrocuted.

•• If any of the following occur, unplug the product immediately and contact your local customer service.

-- The product has been damaged.

-- If water or another substance enters the product (like an AC adapter, power cord, or TV).

-- If you smell smoke or other odors coming from the TV

-- When lightning storms or when unused for long periods of time.

Even the TV is turned off by remote control or button, AC power source is connected to the unit if not unplugged in.

•• Do not use high voltage electrical equipment near the TV (e.g., a bug zapper). This may result in product malfunction.

•• Do not attempt to modify this product in any way without written authorization from LG Electronics. Accidental fire or electric shock can occur. Contact your local customer service for service or repair. Unauthorized modification could void the user’s authority to operate this product.

•• Use only an authorized attachments / accessories approved by LG Electronics. Otherwise, this may result in fire, electric shock, malfunction, or product damage.

•• Never disassemble the AC adapter or power cord. This may result in fire or electric shock.

•• Handle the adapter carefully to avoid dropping or striking it. An impact could damage the adapter.

•• To reduce the risk of fire or electrical shock, do not touch the TV with wet hands. If the power cord prongs are wet or covered with dust, dry the power plug completely or wipe dust off.

•• Batteries

-- Store the accessories (battery, etc.) in a safe location out of the reach of children.

-- Do not short circuit, disassemble, or allow the batteries to overheat. Do not dispose of batteries in a fire. Batteries should not be exposed to excessive heat.

-- Caution: Risk of fire or explosion if the battery is replaced by an incorrect type.

•• Moving

-- When moving, make sure the product is turned off, unplugged, and all cables have been removed. It may take 2 or more people to carry larger TVs. Do not press or put stress on the front panel of the TV. Otherwise, this may result in product damage, fire hazard or injury.

•• Keep the packing anti-moisture material or vinyl packing out of the reach of children.

•• Do not allow an impact shock, any objects to fall into the product, and do not drop anything onto the screen.

•• Do not press strongly upon the panel with a hand or a sharp object such as a nail, pencil, or pen, or make a scratch on it. It may cause damage to screen.

•• Cleaning

-- When cleaning, unplug the power cord and wipe gently with a soft/dry cloth. Do not spray water or other liquids directly on the TV. Do not clean your TV with chemicals including glass cleaner, any type of air freshener, insecticide, lubricants, wax (car, industrial), abrasive, thinner, benzene, alcohol etc., which can damage the product and/or its panel. Otherwise, this may result in electric shock or product damage.

<![if ! IE]>

<![endif]>ENGLISH

3

<![if ! IE]>

<![endif]>ENGLISH

Preparing

Separate Purchase

•  If the TV is turned on for the first time after it was shipped from the

	factory, initialization of the TV may take a few minutes.
•	Image shown may differ from your TV.
•	Your TV’s OSD (On Screen Display) may differ slightly from that
	shown in this manual.
•	The available menus and options may differ from the input source
	or product model that you are using.
•	New features may be added to this TV in the future.
•	The device must be easily accessed to a location outlet near the
	access. Some devices are not made by turning on / off button,
	turning off the device and unplugging the power cord.
•	The items supplied with your product may vary depending on the
	model.
•	Product specifications or contents of this manual may be changed
	without prior notice due to upgrade of product functions.
•	For an optimal connection, HDMI cables and USB devices should
	have bezels less than 10 mm thick and 18 mm width. Use an
	extension cable that supports		if the USB cable or USB
	memory stick does not fit into your TV’s USB port.
	B	B	*A =< 10 mm
	A	A
			=
			*B < 18 mm
•	Use a certified cable with the HDMI logo attached.
•	If you do not use a certified HDMI cable, the screen may not display
	or a connection error may occur. (Recommended HDMI Cable Types)
	-- Ultra High Speed HDMI®/™ cable (3 m or less)

Separate purchase items can be changed or modified for quality improvement without any notification. Contact your dealer to buy these items. These devices only work with certain models.

The model name or design may be changed depending on the upgrade of product functions, manufacturer’s circumstances or policies.

The manufacturer shall not be held responsible for any injuries, damages, or quality issues that may arise if an item that is not listed below is purchased separately and used.

Magic Remote Control

AN-MR19BA

Check whether your TV model supports Bluetooth in the Wireless Module Specification to verify whether it can be used with the Magic Remote.

Companion Box (AV box) Wall mount

W7AWB

4

Lifting and moving the TV

Please note the following advice to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size.

•  It is recommended to move the TV in the box or packing material that the TV originally came in.

•  Before moving or lifting the TV, disconnect the power cord and all cables.

•  When holding the TV, the screen should face away from you to avoid damage.

•  Hold the top and bottom of the TV frame firmly. Make sure not to hold the transparent part, speaker, or speaker grill area.

•  When transporting a large TV, there should be at least 2 people. •  When transporting the TV by hand, hold the TV as shown in the

following illustration.

•  When transporting the TV, do not expose the TV to jolts or excessive vibration.

•  When transporting the TV, keep the TV upright, never turn the TV on its side or tilt towards the left or right.

•  Do not apply excessive pressure to cause flexing / bending of frame chassis as it may damage screen.

•  When handling the TV, be careful not to damage the protruding buttons.

•  Avoid touching the screen at all times, as this may result in damage to the screen.

•  When supported cable is not long enough to connect TV set with Companion Box (AV Box), you can use an extension cable.

•  Please do not pile the stuff up or press strongly the speaker. This may result in product damage or degradation.

Mounting to the Wall

When you attach the TV to other building materials, please contact qualified personnel.

•  The installation should be done by a qualified and licensed electrician in accordance with wiring rules in the Australian and New Zealand Standards AS/NZS 3000 for Electrical Installations. (Depending on country)

•  Do not apply foreign substances (oils, lubricants, etc.) to the screw parts when assembling the product. (Doing so may damage the product.)

•  Do not use any unapproved items to ensure the safety and product life span.

•  Any damage or injuries caused by using unapproved items are not covered by the manufacturer’s warranty.

•  Make sure that the screws are inserted correctly and fastened securely. (If they are not fastened securely enough, the TV may tilt forward after being installed.) Do not use too much force and over tighten the screws; otherwise screw may be damaged and not tighten correctly.

<![if ! IE]>

<![endif]>ENGLISH

5

<![if ! IE]>

<![endif]>ENGLISH

Provided item

Wall mount	Punching Guide

Wall mounting screw

Wall mounting anchor

Ø5 x L65

Wall mounting screw for wood Ø3 x L18

•• Check the material of the wall and the thickness of the finishing.

•• Use the Wall mount anchor for wall material of concrete, light concrete, strong natural stone, soft natural stone masonry brick and hallow block that do not crack.

	Wall Material	Tools	Wall Width
	Concrete	Wall mounting
		anchor, Wall
	Brick
		mounting screw,	70 mm
	Natural stone
		Ø 3/6/8 mm
	Metal Panel	Drill bit
	Plywood	Wall mounting	30 mm
	EPS Panel	screw, Ø 1.8 mm	Penetrate the wall
		Drill bit
	Plasterboard + Plywood		30 mm

•• When installing on a gypsum board or medium-density fiberboard (MDF) wall, fasten the screws to the studs that support the wall. If there are no studs, check the distance from the inner wall before installing.

-- 30 mm or below: Install directly on the inner wall using a 65 mm screw.

-- 30 mm or above: Install using a separate hanger.

Wall

•• When installing the wall mount, check the positions of the wooden studs using a stud finder. Then, fasten the screws on at least two separate studs before proceeding.

Stud

Wall mount

•• When installing the product on wall material not designated, install the product so that each location can withstand the pull out load of 70 kgf (686 N) and shear load of 100 kgf (980 N) or above.

•• Use the Ø 8 mm drill bit for concrete and hammer (Impact) drill.

Tools you will need

•• Phillips head + driver (manual or motorized), Ø 3/6/8 mm Drill bit, Level, Stud finder, Drill

6

How to attach to masonry walls

Please follow the below direction.

1Use a drill bit Ø 8 mm to drill a hole for the anchor location within a depth of 80 mm to 100 mm.

2Clean the drilled hole.

3Insert the sealed wall mounting anchor to the hole. (When inserting the anchor, use a hammer.)

Wall mounting anchor

4Set the wall mount on the wall by aligning to the location of the hole. And, set the angle adjusting part to face upward.

Wall mount

5Align the wall mounting screw to the hole and tighten it. Then, fasten the screws at torque of 45 kgf/cm to 60 kgf/cm.

Wall mounting screw

•  When mounting a TV on the wall, make sure not to install the TV by hanging the power and signal cables on the back of the TV.

•  Do not install this product on a wall if it could be exposed to oil or oil mist. This may damage the product and cause it to fall.

•  Make sure that children do not climb on or hang on the TV.

•  Use a platform or cabinet that is strong and large enough to support the TV securely.

•  When installing the product, first check that the wall is strong enough. Use the anchors and screws provided.

-- If you use anchors and screws that are not specified by the manufacturer, they may not hold the weight of the product, causing safety issues.

•  Be sure to use the accessory cable provided. Otherwise, friction between the product and the wall may cause damage to the connector.

•  When drilling holes into the wall, make sure you use a drill and drill bit with the specified diameter. Ensure that you also follow the instructions regarding the depth of the holes.

-- Otherwise, the product may be installed incorrectly and cause safety issues.

•  Wear safety gloves when installing the product. Do not use your bare hands.

-- Otherwise, it may cause personal injury.

•  If some parts of the wall mount do not touch the wall after it is attached, use the double-sided tape included in the accessory box to stick the mount to the wall.

•  If some parts of the wall mount do not touch the wall after using the wall mounting screws for wood, use the remaining screws.

•  Be sure to use only the exclusive wall mounting screws provided as accessories.

•  If you want to connect the TV Cable is connected to the back panel partition, please use the enclosed Punching Guide.

<![if ! IE]>

<![endif]>ENGLISH

7

Using the kensington security system

		(Only OLED65W9*)
	<![if ! IE]> <![endif]>ENGLISH	The Kensington security system connector is located at the rear of
		the Companion Box (AV Box). For more information of installation
		and using, refer to the manual provided with the Kensington security
		system or visit http://www.kensington.com.

Connections

Connect various external devices to the TV and switch input modes to select an external device. For more information of external device’s connection, refer to the manual provided with each device.

Antenna/Cable

Connect the TV to a wall antenna socket with an RF cable (75 Ω).

•  Use a signal splitter to use more than 2 TVs.

•  If the image quality is poor, install a signal amplifier properly to improve the image quality.

•  If the image quality is poor with an antenna connected, try to realign the antenna in the correct direction.

•  An antenna cable and converter are not supplied.

•  For a location that is not supported with ULTRA HD broadcasting, this TV cannot receive ULTRA HD broadcasts directly.

Satellite dish

Connect the TV to a satellite dish to a satellite socket with a satellite RF cable (75 Ω). (Depending on model)

Other connections

Connect your TV to external devices. For the best picture and audio quality, connect the external device and the TV with the HDMI cable. Some separate cable is not provided.

HDMI

•  When connecting the HDMI cable, the product and external devices should be turned off and unplugged.

•  Supported HDMI Audio format : (Depending on model)

DTS (44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz),

DTS HD (44.1 kHz, 48 kHz, 88.2 kHz, 96 kHz, 176.4 kHz, 192 kHz), True HD (48 kHz),

Dolby Digital / Dolby Digital Plus (32 kHz, 44.1 kHz, 48 kHz), PCM (32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192 kHz)

(Only UHD models)

• → ( ) →[Picture] →[Additional Settings] →[HDMI ULTRA HD Deep Colour]

-- On : Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0) -- Off : Support 4K @ 50/60 Hz 8 bit (4:2:0)

If the device connected to Input Port also supports ULTRA HD Deep Colour, your picture may be clearer. However, if the device doesn’t support it, it may not work properly. In that case, change the TV’s [HDMI ULTRA HD Deep Colour] setting to off.

USB

Some USB Hubs may not work. If a USB device connected using a USB Hub is not detected, connect it to the USB port on the TV directly.

External Devices

Available external devices are: Blu-ray player, HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices.

•  The external device connection may differ from the model.

•  Connect external devices to the TV regardless of the order of the TV port.

•  If you record a TV program on a Blu-ray/DVD recorder or VCR, make sure to connect the TV signal input cable to the TV through a DVD recorder or VCR. For more information of recording, refer to the manual provided with the connected device.

•  Refer to the external equipment’s manual for operating instructions.

8

•  If you connect a gaming device to the TV, use the cable supplied with the gaming device.

•  In PC mode, there may be noise associated with the resolution, vertical pattern, contrast or brightness. If noise is present, change the PC output to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the PICTURE menu until the picture is clear.

•  In PC mode, some resolution settings may not work properly depending on the graphics card.

•  If ULTRA HD content is played on your PC, video or audio may become disrupted intermittently depending on your PC’s performance.

•  When connecting via a wired LAN, it is recommended to use a CAT 7 cable. (Only whenport is provided.)

Using Button

You can simply operate the TV functions, using the button.

Basic functions

Power On (Press)

Power Off 1 (Press and hold)

Volume Control

Programmes Control

1All running apps will close, and any recording in progress will stop. (Depending on country)

Adjusting the menu

When the TV is turned on, press thebutton one time. You can adjust the Menu items using the button.

Turns the power off.

Accesses the settings menu.

Clears on-screen displays and returns to TV viewing.

Changes the input source.

<![if ! IE]>

<![endif]>ENGLISH

9

<![if ! IE]>

<![endif]>ENGLISH

Using Magic Remote

Control

(Depending on model)

The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly.

When the message [Magic Remote battery is low. Please change the battery.] is displayed, replace the battery.

To replace batteries, open the battery cover, replace batteries (1.5 V AA) matching theandends to the label inside the compartment, and close the battery cover. Be sure to point the magic remote toward the remote control sensor on the TV. To remove the batteries, perform the installation actions in reverse.

1	1
1	1

(Some buttons and services may not be provided depending on models or regions.)

To use the button, press and hold for more than 1 second.

(POWER) Turns the TV on or off.

(STB POWER) You can turn your set-top box on or off by adding the set-top box to the universal remote control for your TV. Number buttons Enters numbers.

Accesses the [QUICK HELP].

(DASH) Inserts a between numbers such as 2-1 and 2-2. (DASH) Enter data broadcast.

Accesses the saved programmes list.

(MORE ACTIONS) Displays more remote control functions.

Edits QUICK ACCESS.

-- QUICK ACCESS is a feature that allows you to enter a specified app or Live TV directly by pressing and holding the number buttons.

Audio descriptions function will be enabled.

Adjusts the volume level.

(MUTE) Mutes all sounds.

(MUTE) Accesses the [Accessibility] menu.

Scrolls through the saved programmes.

(Voice recognition) Network connection is required to use the voice recognition function. Once the voice display bar is activated on the TV screen, press and hold the button and speak your command out loud.

(HOME) Accesses the Home menu.

(HOME) Shows the previous history.

(Q. Settings) Accesses the Quick Settings.

(Q. Settings) Displays the [All Settings] menu.

Wheel (OK) Press the center of	button to select a menu. You
can change programmes by using	button.
(up/down/left/right) Press the up, down, left or right
button to scroll the menu. If you press	buttons while the

pointer is in use, the pointer will disappear from the screen and Magic Remote will operate like a general remote control. To display the pointer on the screen again, shake Magic Remote to the left and right. (BACK) Returns to the previous level.

(BACK) Clears on-screen displays and returns to last input viewing.

Shows programme guide.

1 Streaming Service buttons Connects to the Video Streaming

Service.

Shows the previous history.

(INPUT) Changes the input source.

(INPUT) Accesses the [HOME DASHBOARD].

Displays the set-top box Home menu.

-- When you are not watching via a set-top box: the display changes to the set-top box screen.

,	,	,	These access special functions in some
menus.

Runs the record function.

Enter Cheering mode.

, (Control buttons) Controls media contents.

10

Registering Magic Remote Control

How to register the Magic Remote Control

To use the Magic Remote, first pair it with your TV.

1Put batteries into the Magic Remote and turn the TV on.

2Point the Magic Remote at your TV and press the Wheel (OK) on the remote control.

*If the TV fails to register the Magic Remote, try again after turning the TV off and back on.

How to deregister the Magic Remote Control

Press the(BACK) and(HOME) buttons at the same time, for five seconds, to unpair the Magic Remote with your TV.

*Pressing and holding thebutton will let you cancel and re-regis- ter Magic Remote at once.

•  It is recommended that an Access Point (AP) be located more than 0.2 m away from the TV. If the AP is installed closer than 0.2 m, the Magic remote control may not perform as expected due to frequency interference.

•  In Analogue TV and some countries, some remote control buttons may not work.

•  Do not mix new batteries with old batteries. This may cause the batteries to overheat and leak.

•  Failure to match the correct polarities of the battery may cause the battery to burst or leak, resulting in fire, personal injury, or ambient pollution.

•  This apparatus uses batteries. In your community there might be regulations that require you to dispose of these batteries properly due to environmental considerations. Please contact your local authorities for disposal or recycling information.

•  Batteries inside or inside the product shall not be exposed to excessive heat such as sunshine, fire or the like.

User Guide

For more information about this TV, read the USER GUIDE embedded in the product.

•  To open the USER GUIDE →()→[General] →[About This TV] →[User Guide]

Troubleshooting

Cannot control the TV with the remote control.

•  Check the remote control sensor on the product and try again.

•  Check if there is any obstacle between the product and the remote control.

•  Check if the batteries are still working and properly installed (

	to ,	to ).
No image display and no sound is produced.
•	Check if the product is turned on.
•	Check if the power cord is connected to a wall outlet.
•	Check if there is a problem in the wall outlet by connecting other

products.

The TV turns off suddenly.

•  Check the power control settings. The power supply may be interrupted.

•  Check if the auto-off function is activated on the settings related time.

•  If there is no signal while the TV is on, the TV will turn off automatically after 15 minutes of inactivity.

When connecting to the PC (HDMI), no signal is detected.

•  Turn the TV off/on using the remote control. •  Reconnect the HDMI cable.

•  Restart the PC with the TV on.

Abnormal Display

•  If the product feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is nothing wrong with product.

•  This panel is an advanced product that contains millions of pixels. You may see tiny black dots and/or brightly coloured dots (white, red, blue or green) at a size of 1 ppm on the panel. This does not indicate a malfunction and does not affect the performance and reliability of the product.

This phenomenon also occurs in third-party products and is not subject to exchange or refund.

•  You may find different brightness and colour of the panel depending on your viewing position(left/right/top/down). This phenomenon occurs due to the characteristic of the panel. It is not related with the product performance, and it is not malfunction.

<![if ! IE]>

<![endif]>ENGLISH

11

<![if ! IE]>

<![endif]>ENGLISH

•• A blue light blinks on the front of the Companion Box (AV Box). -- The TV may have a problem with the cooling fan or the

temperature in the TV may be too high. Contact an authorized service center.

•• A magenta light blinks on the front of the Companion Box (AV Box). -- The TV may have a problem in the moving speaker. Contact an

authorized service center.

•• An orange light blinks on the front of the Companion Box (AV Box). -- The cable from panel may not be properly connected to the

Companion Box (AV Box). Unplug the power cord and reconnect the cable and then plug the power cord and press the power button. If it still doesn’t work after the steps above, contact an authorized service center.

Generated Sound

•  “Cracking” noise: A cracking noise that occurs when watching or turning off the TV is generated by plastic thermal contraction due to temperature and humidity. This noise is common for products where thermal deformation is required.

•  Electrical circuit humming/panel buzzing: A low level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending on the product.

This generated sound does not affect the performance and reliability of the product.

•  Make sure to wring any excess water or cleaner from the cloth.

•  Do not spray water or cleaner directly onto the TV screen. •  Make sure to spray just enough of water or cleaner onto a

dry cloth to wipe the screen.

•  To clean the top of the Companion Box (AV box), spray a soft cloth with water. Then, wipe the surface so that the product does not come in direct contact with water. Next, wipe it again so that no moisture remains.

12

Specifications

Broadcasting Specifications

		Digital TV			Analogue TV
		(Depending on country)			(Depending on country)
		DVB-T/T2			PAL B/B, PAL B/G,
Television system					PAL D/K, PAL-I,
		DVB-C
					SECAM B/G, SECAM D/K,
		DVB-S/S2
					NTSC-M
	DVB-S/S21	DVB-C1		DVB-T/T21
				VHF III : 174 ~ 230 MHz
Program coverage				UHF IV : 470 ~ 606 MHz	46 ~ 862 MHz
	950 ~ 2150 MHz	46 ~ 890 MHz		UHF V : 606 ~ 862 MHz
				S Band II : 230 ~ 300 MHz
				S Band III : 300 ~ 470 MHz
Maximum number of	6,000			3,000
storable programmes
External antenna		75 Ω
impedance

1 Only DVB-T2/C/S2 support model only.

•  The energy information provided with the product is indicated in accordance with the regulations of each country. (Depending on country) -- The Energy consumption is measured in accordance with IEC 62087.

•  Actual Energy consumption may vary depending on factors such as the type of video content being played and TV settings.

(Except for Philippines)

Wireless module(LGSBWAC92)Specifications

	Wireless LAN (IEEE 802.11a/b/g/n/ac)
Frequency range		Output power(Max.)
2400 to 2483.5 MHz		18 dBm
5150 to 5725 MHz		18 dBm
5725 to 5850 MHz (Not for EU)		12 dBm
	Bluetooth
Frequency range		Output power(Max.)
2400 to 2483.5 MHz		8 dBm

As band channels can vary per country, the user cannot change or adjust the operating frequency. This product is configured for the regional frequency table.

For consideration of the user, this device should be installed and operated with a minimum distance of 20 cm between the device and the body. * IEEE 802.11ac is not available in all countries.

<![if ! IE]>

<![endif]>ENGLISH

13

<![if ! IE]>

<![endif]>ENGLISH

(Only Philippines)

	Wireless module(LGSBWAC92)Specifications
	Wireless LAN (IEEE 802.11a/b/g/n/ac)
Frequency range		Output power(Max.)
2400 to 2483.5 MHz		18 dBm
5150 to 5725 MHz		18 dBm
5725 to 5850 MHz		18 dBm
	Bluetooth
Frequency range		Output power(Max.)
2400 to 2483.5 MHz		8 dBm

As band channels can vary per country, the user cannot change or adjust the operating frequency. This product is configured for the regional frequency table.

For consideration of the user, this device should be installed and operated with a minimum distance of 20 cm between the device and the body. FCC ID: BEJLGSBWAC92 / IC: 2703H-LGSBWAC92

	Environment condition
Operating Temperature		0 °C to 40 °C
Operating Humidity		Less than 80 %
Storage Temperature		-20 °C to 60 °C
Storage Humidity		Less than 85 %

14

Open Source Software

Notice Information

To obtain the source code under GPL, LGPL, MPL, and other open source licenses, that is contained in this product, please visit http:// opensource.lge.com.

In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download.

LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping, and handling) upon email request to [e-mail].

This offer is valid for a period of three years after our last shipment of this product. This offer is valid to anyone in receipt of this information.

Licenses

(Magic Remote supported models only)

<![if ! IE]>

<![endif]>ENGLISH

15

<![if ! IE]>

<![endif]>ENGLISH

Important Information for Preventing Image Retention

OLED is a self-emissive technology, which brings many significant benefits to image quality and performance. As with any self-emitting display, it is possible for users of OLED TVs to experience temporary image retention under certain conditions, such as when displaying a static image on the screen for a long time. LG OLED TVs incorporate dedicated functions that protect the screen from possible image retention.

If a static image persists on screen, screen brightness is automatically reduced in specific areas of, or across the entire screen. Once the static image disappears, screen brightness will automatically return to its prior setting. This is not a product malfunction.

Examples of Images that may Cause Image Retention

•• Still images or fixed images containing certain information that are displayed uninterrupted on the screen, such as channel numbers, station logos, program titles, news or movie subtitles, and headlines.

•• Fixed menu or icons for video game consoles or broadcasting set-top boxes.

•• Black bars shown on the left, right, top, or bottom of the screen, such as in images with a 4:3 or 21:9 ratio.

Recommended Measures for Preventing Image Retention

•• Avoid watching a video displaying an image as listed above for extended periods of time.

•• Adjust your TV settings as below when turning on a video exhibiting an image as listed above for extended periods of time. -- [Picture] →[Picture Mode Settings] →[Picture Mode] →

[Eco]/[APS] (Depending on model)

-- [Picture] →[Picture Mode Settings] →[OLED LIGHT] →Adjust to lower value

-- [Picture] →[Additional Settings] →[OLED Panel Settings] → [Logo Luminance Adjustment] →[High]

•• Turn off the menu bar of an external device, such as a set-top box, to prevent long-term display of the menu bar of such device. (Please refer to the manual of the applicable external device for instructions.)

•• Adjust the settings as below when watching a video constantly showing black bars on the left, right, top or bottom, in order to remove the black bars.

-- [Picture] →[Aspect Ratio Settings] →[Aspect Ratio] → [Vertical Zoom] or [All-Direction Zoom]

Information on Functions Supporting Image Quality in Relation to Temporary Image Retention

•• LG OLED TVs provide a feature called Pixel Refresher, which helps to prevent temporary image retention.

•• When the accumulated television viewing time reaches 2,000 hours or more (this is equivalent to watching TV for five hours a day over the course of a year), Pixel Refresher will be automatically activated once your TV is turned off. When turning off your TV, a notice will appear on the screen informing the activation of Pixel Refresher. This feature will run for an hour while your TV is turned off. A horizontal line may appear at the top or bottom of the screen when the process is almost finished.

•• You may also manually activate Pixel Refresher via the TV menu:

→ ) →[Picture] →[Additional Settings] →[OLED Panel Settings] →[Pixel Refresher].

•• Whenever you watch your TV for more than four cumulative hours, Pixel Refresher will be automatically activated for a few minutes once your TV is turned off. (Note: Pixel Refresher will not be activated if the power cord of your TV is not plugged in or the main power is off.)

16

Regulatory

WARNING!

Never place a television set in an unstable location. A television set may fall, causing serious personal injury or death. Many injuries, particularly to children, can be avoided by taking simple precautions such as:

•• Using cabinets or stands recommended by the manufacturer of the television set.

•• Only using furniture that can safely support the television set.

•• Ensuring the television set is not overhanging the edge of the supporting furniture.

•• Not placing the television set on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the television set to a suitable support.

•• Not placing the television set on cloth or other materials that may be located between the television set and supporting furniture.

•• Educating children about the dangers of climbing on furniture to reach the television set or its controls.

If your existing television set is being retained and relocated, the same considerations as above should be applied.

Symbols

Refers to alternating current(AC).

Refers to direct current(DC).

Refers to class II equipment.

Refers to stand-by.

Refer to “ON” (power).

Refers to dangerous voltage.

<![if ! IE]>

<![endif]>ENGLISH

17

The model and serial number of the product are located on the back and on one side of the product. Record them below in case you ever need service.

MODEL

SERIAL NO.

For any Suggestion, Opinion, Complaints, Please Call 800 54 in UAE

0800 545454 in South Africa

080 100 54 54 in Morocco

19960 in Egypt

021 36 54 54 in Algeria Other countries, Please contact our

local dealer or log into

http://www.lg.com

Sécurité et référence

Veuillez lire attentivement ce manuel avant de mettre en service votre produit et conservez-le afin de pouvoir vous y référer ultérieurement.

www.lg.com

Copyright2019 LG Electronics Inc. Tous droits réservés.

Avertissement! Consignes de sécurité

			AVERTISSEMENT
			RISQUE D'ÉLECTROCUTION
	<![if ! IE]> <![endif]>FRANÇAIS		NE PAS OUVRIR
		AVERTISSEMENT : AFIN DE RÉDUIRE LE RISQUE D'ÉLECTROCUTION,
		NE RETIREZ PAS LE CAPOT (OU L'ARRIÈRE). AUCUNE PIÈCE N'EST
		RÉPARABLE PAR L'UTILISATEUR LUI-MÊME. CONFIEZ L'ENTRETIEN
		DE CET APPAREIL À UN PERSONNEL QUALIFIÉ.

Ce symbole est destiné à prévenir l'utilisateur de la présence d'une « tension dangereuse » non isolée dans le

boitier du produit. Cette tension peut être d'amplitude suffisante pour constituer un risque d'électrocution.

Ce symbole est destiné à prévenir l'utilisateur que des instructions importantes sur le fonctionnement et

l’entretien (réparation) de l'appareil se trouvent dans la documentation.

AVERTISSEMENT : AFIN DE RÉDUIRE LE RISQUE D'INCENDIE ET D'ÉLECTROCUTION, N'EXPOSEZ PAS LE PRODUIT À LA PLUIE OU À L'HUMIDITÉ.

•• POUR PRÉVENIR TOUT RISQUE D’INCENDIE, TENEZ LES BOUGIES OU AUTRES OBJETS À FLAMMES NUES ÉLOIGNÉS DE CE PRODUIT EN TOUT TEMPS.

•• N’installez pas la TV et la télécommande dans les environnements suivants :

-- Évitez d’exposer l’appareil à la lumière directe du soleil. -- Une zone fortement humide comme une salle de bain

-- À proximité d’une source de chaleur comme une cuisinière et tout autre appareil produisant de la chaleur.

-- À proximité d’un plan de travail de cuisine ou d’un humidificateur où elles pourraient facilement être exposées à la vapeur ou à l’huile.

-- Une zone exposée à la pluie et au vent.

-- Ne placez pas d'objets contenant du liquide (tel qu'un vase, une tasse, etc.) sur ou au-dessus de ce produit (par exemple, sur une étagère au-dessus de l'unité).

-- N'installez pas le téléviseur à proximité d'objets inflammables, comme de l'essence ou des bougies. N'exposez pas directement le téléviseur à l'air conditionné.

-- N'installez pas l'appareil dans un endroit excessivement poussiéreux.

Le non-respect de cette consigne peut provoquer un incendie, un choc électrique, une combustion/explosion, un dysfonctionnement ou une déformation du produit.

•• Ventilation

-- Installez le téléviseur dans un endroit bien aéré. Évitez les espaces fermés, tels qu'un meuble de bibliothèque.

-- N’installez pas le produit sur un tapis ou un coussin.

-- Évitez de bloquer ou de couvrir le produit avec un tissu ou autre matériau lorsque l'unité est branchée.

•• Évitez de toucher les ouvertures de ventilation. Lors de l'utilisation prolongée du téléviseur, les ouvertures de ventilation peuvent surchauffer.

•• Protégez le câble d’alimentation contre les mauvais traitements physiques ou mécaniques, la torsion, la pliure, le pincement, et évitez qu’il ne puisse être pris dans une porte ou que l’on puisse marcher dessus. Vérifiez soigneusement les fiches, les prises murales et les points de sortie du cordon de l'appareil.

•• Ne déplacez pas le téléviseur tant que le cordon d'alimentation est branché.

•• N'utilisez pas de cordon d'alimentation endommagé ou déformé.

•• Veillez à tenir le cordon d'alimentation par la fiche pour le débrancher. Ne tirez pas sur le cordon d'alimentation pour débrancher le téléviseur.

•• Ne branchez pas trop d'appareils à la même prise secteur pour éviter les risques d'incendie ou de choc électrique.

•• Déconnexion de l'appareil de l'alimentation principale

-- La fiche d'alimentation est l'élément de déconnexion. En cas d'urgence, la fiche d'alimentation doit rester facilement accessible.

•• Ne laissez pas les enfants grimper sur la TV ou s’agripper dessus. Dans le cas contraire, la TV risque de tomber ce qui peut entraîner des blessures graves.

•• Mise à la terre de l'antenne extérieure (peut varier selon le pays):

-- Si une antenne extérieure est installée, respectez les précautions suivantes. Un système d'antenne extérieure ne doit pas être installé à proximité de lignes électriques aériennes ou autres lumières ou circuits électriques. Il ne doit pas entrer en contact avec des lignes ou circuits électriques au risque d'entraîner un décès ou des blessures graves.

Assurez-vous que le système d'antenne est mis à la terre pour assurer une certaine protection contre les surtensions et

l'accumulation des charges statiques. La section 810 du National Electrical Code (NEC) aux États-Unis fournit des informations concernant la mise à la terre correcte de l'antenne et de la structure porteuse, la mise à la terre du câble d'entrée à une unité de décharge d'antenne, la taille des conducteurs de terre, l'emplacement de l'unité de décharge d'antenne, la connexion et les prérequis des électrodes de terre. Mise à la terre d'une antenne selon le National Electrical Code, ANSI/NFPA 70

2

•• Mise à la terre (ne s'applique pas aux appareils ne nécessitant pas de mise à la terre)

-- Un téléviseur muni d'une fiche électrique secteur mise à la terre avec trois broches doit être branché sur une prise secteur mise à la terre avec trois broches. Veillez à brancher le câble de mise à la terre pour éviter les chocs électriques.

•• Ne touchez jamais cet appareil ou cette antenne pendant un orage. Vous pourriez vous électrocuter.

•• Assurez-vous que le cordon d'alimentation est bien branché au téléviseur et à la prise murale. Si ce n'est pas le cas, la fiche

d'alimentation et la prise risquent d'être endommagées. Dans des situations extrêmes, un incendie peut se déclarer.

•• N'insérez pas d'objets métalliques ou inflammables dans le produit. Si un corps étranger tombe dans le produit, débranchez le cordon d'alimentation et contactez le service client.

•• Ne touchez pas le bout du cordon d'alimentation lorsqu'il est branché. Vous risqueriez de subir un choc électrique.

•• Si vous êtes confronté à l'une des situations suivantes, débranchez immédiatement le produit et contactez votre service client local.

-- Le produit a été endommagé.

-- Si de l'eau ou une autre substance pénètre dans le produit (adaptateur secteur, cordon d'alimentation ou téléviseur).

-- Si vous sentez de la fumée ou toute autre odeur émanant du téléviseur

-- Pendant les orages ou lorsque l'appareil n'est pas utilisé pendant un long moment.

Même si le téléviseur est éteint via la télécommande ou un bouton, l'alimentation secteur est connectée à l'unité si elle n'est pas débranchée.

•• N'utilisez pas d'appareil électrique à haute tension à proximité du téléviseur (par exemple, un tue-mouches électrique). Cela pourrait endommager le produit.

•• N'essayez pas de modifier ce produit sans une autorisation écrite de LG Electronics. Un incendie accidentel ou un choc électrique peuvent se produire. Contactez votre service client local pour tout service ou réparation. Des modifications non autorisées peuvent annuler le droit de l'utilisateur à utiliser ce produit.

•• Utilisez uniquement des pièces/accessoires approuvés par

LG Electronics. Le non-respect de cette consigne peut provoquer un incendie, un choc électrique, un dysfonctionnement ou des dommages au produit.

•• Ne démontez pas l’adaptateur secteur ou le câble d’alimentation. Le non-respect de cette consigne peut provoquer un incendie ou une électrocution.

•• Manipulez l'adaptateur avec précaution pour éviter de le faire tomber ou de l'abîmer. Un impact pourrait endommager l'adaptateur.

•• Pour réduire les risques d'incendie ou de choc électrique, ne touchez pas le téléviseur avec les mains mouillées. Si le cordon d'alimentation est mouillé ou couvert de poussière, séchez intégralement la prise d'alimentation ou essuyez la poussière.

•• Batteries

-- Rangez les accessoires (batterie, etc.) dans un endroit sûr hors de portée des enfants.

-- Ne court-circuitez pas les batteries, ne les démontez pas et ne les laissez pas surchauffer. Ne jetez pas les batteries dans un feu. N’exposez pas les piles à une température excessive.

-- Avertissement : Risque d´incendie ou d´explosion si la batterie est remplacée par un autre modèle de batterie inadapté.

•• Déplacement

-- Lorsque vous déplacez le produit, assurez-vous qu'il est éteint, débranché et que tous les câbles ont été retirés. Il faut deux

(2) personnes ou plus pour porter un téléviseur de grande taille. Ne vous appuyez pas sur le panneau avant du téléviseur et n'appliquez aucune pression dessus. Vous risqueriez d'endommager le produit ou de vous exposer à un risque d'incendie ou de blessure.

•• Ne laissez pas le matériau d'emballage anti-humidité ou l'emballage en vinyle à la portée des enfants.

•• Évitez tout impact ou chute d'objets sur l'appareil, et ne laissez rien tomber sur l'écran.

•• N’appuyez pas fortement sur le panneau avec la main ou un objet pointu tel qu'un clou, un crayon ou un stylo. Ne rayez pas le panneau. Cela risquerait d'endommager l'écran.

•• Nettoyage

-- Lorsque vous nettoyez le produit, débranchez le cordon d'alimentation et essuyez délicatement la surface avec un chiffon doux et sec. Ne pulvérisez pas d'eau ou autre liquide directement sur le téléviseur. N’utilisez jamais de produit pour vitre, de désodorisant, d’insecticide, de lubrifiant, de cire pour voiture ou industrielle, d’abrasif, de diluant, de benzène, d’alcool, etc., car ces produits risqueraient d’endommager le produit et / ou son écran. Le non-respect de cette consigne peut provoquer un choc électrique ou endommager le produit.

<![if ! IE]>

<![endif]>FRANÇAIS

3

<![if ! IE]>

<![endif]>FRANÇAIS

Préparation

Achat séparé

•  Si le téléviseur est mis sous tension pour la première fois depuis son expédition depuis l’usine, l’initialisation peut prendre quelques minutes.

•  L’image présentée peut être différente de votre téléviseur.

•  L’affichage à l’écran de votre TV peut différer légèrement de celui

	qui est présenté dans ce manuel.
•	Les menus et options disponibles peuvent être différents selon la
	source d’entrée ou le modèle de produit utilisé.
•	De nouvelles fonctionnalités pourront être ajoutées ultérieurement
	à ce téléviseur.
•	Le téléviseur doit être raccordé à une prise électrique facile d'accès
	située à proximité. Le bouton marche/arrêt n'est pas présent sur
	tous les modèles de produit. Pour éteindre ces appareils, il est
	nécessaire de débrancher le cordon d'alimentation.
•	Les éléments fournis avec votre produit diffèrent en fonction du
	modèle choisi.
•	Les caractéristiques des produits ou le contenu de ce manuel
	peuvent être modifiés sans préavis en cas de mise à jour des
	fonctions.
•	Pour une connexion optimale, les câbles HDMI et les périphériques
	USB doivent comporter des connecteurs d’une épaisseur inférieure
	à 10 mm et d’une largeur inférieure à 18 mm. Utilisez une rallonge
	prenant en charge	si le câble USB ou la clé USB ne s’adapte
	pas au port USB de la TV.
	B	B	*A =< 10 mm
	A	A
			=
			*B < 18 mm
•	Utilisez un câble certifié sur lequel est apposé le logo HDMI.
•	Si vous utilisez un câble non certifié HDMI, l’écran peut ne pas
	s’afficher ou une erreur de connexion peut survenir. (Types de

câbles HDMI recommandés)

-- Câble HDMI®/™ ultra haut débit (max. 3 m)

Des articles vendus séparément peuvent faire l’objet de remplacements ou de modifications sans préavis dans le but d’améliorer la qualité du produit. Contactez votre revendeur pour vous procurer ces articles. Ces périphériques fonctionnent uniquement avec certains modèles.

Le nom ou le design du modèle peut changer en cas de mise à niveau des fonctions du produit, des conditions de diffusion ou des politiques de confidentialité du fabricant.

Le fabricant ne peut être tenu responsable des blessures, dommages ou problèmes de qualité qui peuvent survenir si un élément non répertorié ci-dessous est acheté séparément puis utilisé.

Magic Remote

AN-MR19BA

Vérifiez si votre modèle de téléviseur prend en charge la

fonction Bluetooth dans les spécifications du module sans fil afin de vous assurer qu’il est compatible avec la Magic Remote.

Fixation murale pour Companion Box (boîtier AV)

W7AWB

4